Search Documents

By Y. W. Mou

In order to improve the construction of pile foundations and deep foundations of largo sizes, the paper deals with the method of installing square or rectangular bored-piles for annular foundation as well as large-sized hollow or solid foundation.

Jan 1, 2010

By Z. Q. Bian

The wireline sampling originates from core drilling in rocks. The authors combined the wireline sampling technique with conventional undisturbed soil samplers, including Osterberg sampler, Denison sampler and double tube barrel, and then developed the wireline samplers of WPS, WSS and WSR models. These samplers are able to sample various soils. They reserve all the advantages of the original samplers, and moreover, they are noted with quick hoisting and lowering by wire rope. Therefore, it becomes an efficient new technique of sampling undisturbed soil from deep foundation.

Jan 1, 2010

By Jack Hayes

Vibrating wire strain gages have proven to be a very reliable and effective tool for the measurement of strains associated with the loading of bored piles (drilled shafts). However, when these strains are used to calculate the load, or stresses in the pile, the results can sometimes be confusing and/or difficult to interpret. This paper describes some of these situations, using examples from actual case histories, and discusses some of the difficulties associated with residual load effects, curing and temperature induced strains, load stress distribution effects, estimated modulus and area.

Jan 1, 2002

By Andrew Baxter

This paper focuses on the design of steel bearing plates to transfer load from tiebacks and tiedowns to a concrete mass. It lists and describes the various available procedures for design of bearing plates as well as explains the design procedure recommended by the authors, which incorporates the Post Tensioning Institute (PTI) recommendations. The paper includes a step-by-step design example following the recommended procedure that captures the most important aspects of plate design. The dimensions of the plate calculated from this example are compared to the design dimensions obtained from various other procedures, including those by American Association of State Highway and Transportation Officials (AASHTO) and VSL International, Ltd. (VSL). The paper also includes the results of numerical modeling of the plate that will help the reader understand important aspects of plate-concrete interaction. The authors envision that this paper will serve to create an understanding in the geo-industry of suitable design methods and help improve procurement of bearing plates for tiebacks and tiedowns.

By A. Partos

It was decided to build a fourteen-storied office building over a six-storied garage and a four-storied office building. The high vertical and horizontal loads required foundations on rock approximately 18m below street level. Drilled piers (caissons) were selected. Eight caissons (1.98m diameter) were installed through the six-storied garage and four caissons from a temporary deck at the location of a former two-storied building. Excavations were done by the slurry method. Proof testing of rock was done before construction by test borings and during construction with a core barrel of small diameter. Quality control measures included telecommunications between ground crews and the equipment operator on the garage roof; records of field observations and testing of bentonite slurry and rock; and a continuous evaluation of all information. Instruments were installed in one caisson to monitor load distributions and curing of concrete.

Jan 1, 2010

By Cem Akgüner

The displacements of axially loaded single piles are analyzed with an approach based on elasticity. Young?s modulus and Poisson?s ratio of the soil encompassing a pile are the unknowns required as input to obtain predictions based on the elastic method. Attention is directed towards Young?s modulus because the range and variability of Poisson?s ratio is not significant in displacement calculations. A database of axial pile load tests established for the California Department of Transportation (Caltrans) is investigated. All of the tested piles were driven into the ground. Measurements of displacements and loads were made only at the top of the pile. First the magnitude of displacements is determined up to loads that are half of the failure load measured from pile load tests. Various correlations for Young?s modulus are then employed to determine how accurately each predicts the actual measured displacement. The chosen correlations utilize the routinely available parameters of laboratory triaxial undrained shear strength for cohesive soils and standard penetration test blowcount for cohesionless soils.

Jan 1, 2008

By Leong, William. Chong, Kam Weng

Deep Vibro Techniques namely Vibro Compaction (VC) and Vibro Replacement (VR) are widely used in ground improvement to densify sands and strengthen cohesive soils. This paper describes the application of these techniques for the construction of 20 Ha Iron Ore Stockpile Yard with the maximum stockpile height of 14 m in Quang Ngai, Vietnam. The challenges of this project are to limit the stockpile allowable settlement and the surrounding pile’s lateral movement. The soil condition can be summarized as 12m – 18m thick of loose to medium dense SAND with qc around 5-18MPa and followed by 2.0 – 6.0 m thick soft clay with qc around 0.4 – 0.8MPa. Localized very dense sand layer was found. VR using stone columns were installed in soft clay layer while VC was adopted to densify sand layer. Additional shallow stone columns were built in sand strata to minimize pile top lateral movement. The post construction performance was verified by a large 6 m by 12 m plate load test (PLT). The predicted PLT deformation using Priebe’s improved properties for the VR will be presented and compared with the measured plate load test results.

Nov 1, 2022

By D. Cantali

This paper will be presented in two parts. The first part will present the latest advancements in pile installation techniques using state-of-the-art press-in piling technology by Giken. By pressing in sheet piles and large modulus contiguous steel tube pile walls – as opposed to the more traditional installation methods using percussive hammers or vibrators – retaining structures can be constructed effectively noise and vibration free. For over water and coastal projects with limited access, this provides significant environmental benefits in the form of minimising the construction foot print and the impact to surrounding communities and the marine natural habitat. Typical noise and vibration data will also be presented. The second part of this paper will review the current manufacturing techniques for sheet piles and introduce innovative new materials used in the current piling market for embedded sheet pile walls. Materials include long service life non – ferrous materials such as new age plastics and fibre reinforced polymer piles. Their excellent long term performance and durability make them an effective solution in the marine environment. For steel piles, a number of steel grades with reduced corrosion characteristics will also be discussed including a newly developed steel to combat corrossion in the low water zone, an area often exhibiting the highest moments in a retaining wall. A number of project case studies will also be presented to reinforce their relevance in today’s changing construction landscape.

Nov 1, 2022

By W. Morgan NeSmith

Drilled displacement (DD) piles often develop significantly larger unit shaft resistance values than other drilled or augered pile systems in coarse grained materials. Minimal vibration and limited spoil development are also associated with DD pile installation and these factors are frequently additional financial and/or environmental benefits of the system. The application of DD piles in North America dates to the mid-1990s and their use in the Midwestern United States has been significant, particularly in the past 10 years. The authors have collected an extensive database of DD pile performance in the United States. The alluvial and glacial deposits of the Midwestern U.S. provide conditions where drilled displacement piles perform very efficiently when compared to coastal and residual geologies. This paper presents a summary of the authors? experience regarding installation and performance of DD piles in the Midwestern U.S. Information presented includes summary presentations of DD performance across a range of site conditions as well as a discussion of the relationship of DD performance and installation effort in the Midwest as compared to other geologic settings in the U.S.

Jan 1, 2009

By Viswanadham B. V. S., Babu K. V

Wind energy is one of the most economical renewable energy sources. In order to support wind turbines onshore or offshore open-ended monopile foundations are widely used. Unlike conventional structures, wind turbine foundations experience a large magnitude of lateral loads in the order of 20 % to 30% of total vertical loads. The presence of soft clayey layers at shallow depth along the coastal region, offers lesser lateral load resistance to monopile foundations. One option to enhance lateral load capacity is by introducing fins to the outer surface of the monopiles. Studies pertaining to lateral load response of finned piles in clayey soils are very sparse. This paper presents some of the numerical model studies on the lateral load response of monopiles and finned piles in soft and stiff clay. In the present study, three-dimensional finite element analyses were performed on monopiles as well as finned piles. Analyses were performed in clay with different consistency varying from soft to stiff. Pile material is mild steel for all analyses. The pile section modeled as linear elastic material whereas soil was modeled as Mohr – Coulomb constitutive model with non-associated flow rule. Monopiles and finned piles having four and eight fins with different fin sizes and configurations are considered during the analyses. Finned piles advantage over monopiles to resist lateral load is highlighted in the present study. The results have shown that fins are effective to enhance the lateral load carrying capacity of monopiles and also it reduces the bending moment in monopiles for a given design load.

Sep 1, 2022

By M. Hesham El Naggar, Maged A. Abdlrahem

"Hollow bar micropiles have constructional advantages such as: fast and low-noise and low vibration installation process and small installation equipment, which allow access to tight places. In addition, they have efficient load transfer mechanism, which facilitates carrying considerable load in compression and tension. The common practice is to use diameter ratio of drill bit/ hollow bar (Db/Dh) around 2 in their construction, and they are typically designed assuming type B as classified by the Federal Highway Administration (FHWA). In this paper, the performance and capacity of Hollow bar micropile with different (Db/Dh) ratios are investigated. Full-scale micropiles were installed at a site in Ontario, Canada, and were tested in order to evaluate the uplift performance of Hollow bar micropile with different(Db/Dh) ratios. Two micropiles with two different ratios 2.25 and 3 were constructed and tested. The total length of the micropiles was 6m with embedded length of 5.75m. The soil at the site was primarily medium dense to dense sand. The results of the load tests are presented and discussed. It was found that the uplift capacity of the micropile increased by about 19.5% as Db/Dh increased from 2.25 to 3.INTRODUCTIONMicropile is a small diameter, less than 300 mm, drilled and grouted pile and is typically reinforced according to Federal Highway Administration (FHWA, 2005). The technology of micropile was introduced in North America in 1970’s, but the growth in the east coast of United State was intense compared to all other cities around the globe (Bruce and Nicholson, 1989). Nowadays, micropile construction is used extensively worldwide as a viable solution that offers several advantages such as fast installation in low headroom, minimal disturbance to the adjacent structure efficient load transfer due to high grout to ground bond strength. As the method of grouting has major influence on the grout – ground bond strength, FHWA has classified the micropiles into four categories. Type A: the grout is placed under gravity and no pressure is required. Type B: The grout is typically pressurized under a pressure range from 0.5 to 1 MPa as the temporary casing is withdrawn. Type C: the grout is placed in two-step process. First, the grout is poured under gravity only as in Type A. Before the hardening of the grout, similar grout is pressured of at least 1MPa without the use of packer. Type D: Like Type C, it is a two – step process, the grout is placed under gravity as in Type A and sometimes pressurized as in Type B. After hardening of the initial grout, additional grout is pressurized between 2 to 9 MPa through sleeved pipe by using packers, as many times as needed. According to this classification, hollow bar micropile is usually designated as Type B. However, the construction technique is completely different from Type B. Recently; there is a trend to supplement the four types of micropiles by Type E as represent to hollow bar micropile (Timothy et al, 2012). The construction method of hollow bar micropile involves two main stages which can be performed in one–step process: advancing the drilling bit attached to a threaded hollow bar to the required depth; and pressurizing the grout through nozzles of the drill bit."

Jan 1, 2016

By M. Hesham El Naggar, Mehdi Heidari

"Equivalent fixed-base cantilever model is a common approach for performance base seismic design of bridge structures supported by extended pile-shaft. In this method, global displacement ductility factor is related to local curvature ductility demand by assuming a concentrated plastic hinge at location of maximum bending moment. Equivalent plastic hinge length is one of the key parameters that should be assumed accurately in kinematic expression of the cantilever model. Although, some expressions have proposed to estimate the length of the in-ground plastic hinge; however, these relations yield differing results. In this paper, a general expression is derived based on the concept of distributed plasticity to predict the plastic region of yielded piles in clay and sand. A length modification factor is defined to relate the equivalent length of plastic hinge to the real plastic zone. Then, results from nonlinear pushover analyses are used to propose an equation for the modification factor as a function of displacement ductility factor.IntroductionDuring severe earthquake events, development of the plastic hinge in pile foundation below ground level is inevitable for bridge structures supported on extended pile-shafts. A common approach for seismic design of the yielding pile-shafts is to replace the pile-soil system by an equivalent fixed-base cantilever assuming the equivalent system has the same global response as that of the pile-shaft (Budek et al. 2000; Chai 2002). In this method, plastic curvature is concentrated at the center of the equivalent plastic hinge below ground surface. Prior knowledge of plastic-hinge length is essential for proper assessment of assess plastic displacement at the top of the pile-shaft. Unfortunately, existing recommendations for estimating plastichinge length are largely incomplete and/or inadequate.During the last two decades, several relationships have proposed for evaluating the equivalent plastic hinge length, Lp, based on experimental and numerical studies. Budek et al. (2000) conducted numerical modeling to calculate the plastic-hinge length of piles embedded in cohesionless soil. They found that the plastichinge length varies linearly with both soil stiffness and aboveground height, e. Chai and Hutchinson (2002) conducted full-scale experimental tests on reinforced concrete piles in sand. They reported that Lp depends primarily on the aboveground height of the pile, neither sensitive to the soil stiffness nor to the value of displacement ductility factor. They stated that the equivalent plastic hinge length is relatively independent of the displacement ductility factor and is not very sensitive to the change in soil density. On the contrary, Goel (2014) and Liu et al. (2016) conducted nonlinear numerical analyses which revealed that Lp changes with the displacement ductility factor and even suggested that using different values of Lp for different seismic design levels is essential for a reliable estimation of the ductility capacity."

Jan 1, 2017

By Chris M. Haberfield

The design of side resistance of drilled shafts socketed into rock has traditionally been empirically based on the results of pile loading tests in which the side resistance can be isolated from the side resistance. In practice, this is achieved in one of several ways : loading the pile in tension, using a collapsible base, or by using a device such as an Osterberg cell to load the pile from the base. Although this approach has resulted in generally safe design practice, this has been at the expense of efficient design practice. Safety in design has been achieved through conservatism, which has been necessary because of the large scatter that is evident in the pile socket resistance database (Rowe and Armitage, 1984; Kulhawy and Phoon, 1993). Research at Monash University through the 1980's has been aimed towards understanding and then modelling the complex mechanisms of shear transfer at the concrete-socket interface of sedimentary rocks. Armed with such an understanding, the important factors which affect the strength of pile sockets can be isolated, and the reasons for the large scatter can be deduced. This paper briefly describes the research approach taken, and the main features of the design method and computer program which have now been developed. Some load-settlement predictions of the program are compared with the results of full-scale pile socket tests. The paper then presents the results of a numerical study which relates predicted socket a factors to unconfined compressive strength of the rock, socket diameter, initial normal stress and socket roughness.

Jan 1, 1996

By Christopher J. Ramsey, Don W. Dotson

"An existing four lane section of US 27 was widened to eight lanes. The project lies in the rugged Valley and Ridge Province of the Appalachian mountains starting at the Tennessee River in Chattanooga, Tennessee and extending 2.6 km north to Signal Mountain Boulevard. This terrain presented many challenges to accommodate the road widening in the narrow, rugged topography. Multiple tiered wall systems consisting of large tieback walls, post-tensioned reaction blocks, and gravity MSE walls for a total of approximately 30 retaining walls were required. The retaining walls served to stabilize the thrust faulted geology while also minimizing right-of-way acquisitions. The cut walls consist mainly of a tiered system of tied-back soldier piles walls with cast-in-place concrete facing. Cast-in-place pile shear walls were required along the toe of existing MSE walls to maintain stability during construction. This paper discusses the design methodology, which includes a hybrid (rather than traditional) earth pressure diagram intended to reduce life-cycle maintenance and long-term performance. Further this paper addresses wall construction, slope stability analysis, landslide mitigation alternatives, soldier pile wall design features, site challenges, monitoring and performance (to date) of the wall systems.INTRODUCTIONThis project involves the proposed widening of US Highway 27 (State Route 29) from the north end of the Tennessee River Bridge at Manufacturer’s Road to State Route 8 (Signal Mountain Road), approximately 2.64 km of roadway (Fig. 1). The project site is located adjacent to the Tennessee River on the north side of downtown Chattanooga, Tennessee in Hamilton County. The existing, limited access highway is to be widened from four lanes (two northbound and two southbound) to a minimum of eight lanes. Some portions of the alignment will expand to as much as ten lanes where northbound and southbound ramp acceleration/deceleration lanes coincide.In addition to the number and heights of cuts and fills involved, a major factor in determining an economical design for the alignment is the complicated geologic conditions along the roadway alignment. The existing roadway is situated between several steep cut slopes, some of which are only marginally stable or currently exhibit signs of instability. Due to the proximity of the project to the downtown area, the steep slopes along the alignment, and the relatively dense population near the alignment, widening the pavement and constructing cut and fill slopes to a stable configuration would result in major land acquisition for slope right-of-way."

Jan 1, 2015

By J. G. La Fonta

The rapid development of real-time monitoring technology for the construction of large underground structures in urban areas can be attributed to: the zero-risk objective, the need for transparency between all parties involved and the control of real cost within the budget. Real-time monitoring can be an integral part of the construction contract (for example when compensation grouting is required) or independent, in particular when measurements of existing structures and buildings bordering the project are to be taken before construction starts. Three examples of extensive field instrumentation schemes are described: a large road tunnel in the Moscow suburbs, a new metro line in Amsterdam and major redevelopment works at a busy Central London rail interchange.

Jan 1, 2006

By L. J. Whitworth

Five trial piles were constructed during the trial pile programme for the Birmingham International Convention Centre. In addition, trial piles have been tested on two other sites in central Birmingham. Methods of pile construction were conventional sandstone rock sockets, sleeved piles and voided piles. The results of these load tests are compared with the theoretical predicted behaviour based on the results of unconfined compressive tests of rock core taken on the Convention Centre site and on other sites in the central Birmingham area. On the basis of this work, the various design procedures are discussed.

Jan 1, 1989

By John D. Thornley

Alaskan villages typically store a one-year supply of fuel to reduce significant delivery costs. Alaska Village Electric Cooperative (AVEC), an electric utility cooperative providing power to 51 Alaska villages, has made a concerted effort to upgrade and improve their undersized and aging facilities. The Village of Stebbins, located south of Nome on Norton Sound is receiving upgrades to its AVEC bulk fuel facilities. Stebbins offered unique challenges from a foundations perspective due to the nature of the soil. The geotechnical investigation found the soil below roughly a third of the footprint of the bulk fuel facility to be thawed with seasonal freezing and the remainder was found to be warm permafrost with ground temperatures of between 30°F and 32°F. This is a unique and challenging arctic engineering design issue because foundations are designed differently for frozen ground conditions. Driven piles were selected because of site constraints, such as the design flood elevation and the change from thawed to frozen ground conditions. The pile design specified that the pile embedment depths would be selected based on the results of pile driving analyzer (PDA) testing during construction in the thawed ground and maintained within the frozen ground portion of the footprint. Difficulties during pile driving in the frozen ground resulted in several piles becoming severely damaged, requiring subsequent removal. This resulted in a reevaluation of the means and methods for pile installation. Additional fieldwork was performed to further characterize the subsurface soils and their frozen nature. Options for installation of piles in difficult areas were evaluated including ground thawing, predrilling, and reducing embedment depths. Presented within this paper are the findings from the initial and subsequent field explorations, discussion of the design methodology, and the decisions that led to successful installation of piles at this challenging remote village.

By Charles M. Wilk

"Mass stabilization (MS) is a ground improvement technique that can prepare areas of low bearing strength soil for subsequent infrastructure development. The technique involves mixing binding agents such as portland cement, fly ash, slag, or lime into the subject soil while the soil remains in-place (insitu). The binders “cement” the soil grains together to form a cement modified soil or a soil cement. The MS-treated area now has improved bearing capacity to support infrastructure or to prevent movement of the material such as landslides.The same insitu soil mixing technique can be used to address contaminated areas. Binders or reagents are mixed into soil. The treatment protects human health and the environment by immobilizing hazardous constituents within the treated material. When used for the purpose of environmental remediation the technology is called Insitu Solidification/Stabilization (ISS).Both Mass Stabilization and ISS treatments require laboratory studies to develop a mix design of soil and binder(s) that produce the desired physical and/or chemical properties. The mix design is then transferred into the field. Successful MS and ISS treatments rely on reproduction at full-scale of the mix design and the thorough mixing attained at laboratory scale. Fifty to 70% of the cost of a MS or ISS project is in the cost of the binding agent that is to be mixed into the subject soil. Under-dosing, overdosing, non-thorough mixing, and mixing in the wrong areas all create cost over-runs.This paper will discuss recent innovations in mass stabilization systems that improve the cost effectiveness of the treatment technology. Specialized equipment can impart greater mixing shear thus improving the thoroughness of mixing. Dry powder pressure feeders can conserve the “drying capacity” of binder resulting in higher strengths at lower binder dosages. Global Positioning System (GPS)-based systems can guide the mixing operator for complete mixing coverage. An integrated tracking and feeding system can record that proper dosing and mixing was accomplished and generate construction QA/QC reports for the client.INTRODUCTIONNew or expanding infrastructure projects may encounter areas of low bearing capacity soil or areas where marginal materials such as waste, dredged material, or sediment have been placed. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu.Mass stabilization technique can also address contaminated soil therefore, the same technique can be used to attain both civil and environmental engineering goals. In this environmental application the technology is known as insitu solidification/stabilization (ISS). ISS protects human health and the environment by immobilizing hazardous constituents within the treated material."

Jan 1, 2015

By Arturo Ressi di Cervia

"The Construction of the Thrust Pits for Jacking of the I-90 Tunnel for the Central Artery/Tunnel Project (Part of Contract No. C09A4) in Boston MA was nominated for DFI’s 2002 Outstanding Project Award. In the judging, the project and the specialty subcontractor, Treviicos Corporation, was chosen for a Special Recognition Award. INTRODUCTIONBoston’s Big Dig, as the construction of the underground artery became known, is undoubtedly the largest urban construction project of this century.The Central Artery/Tunnel Project, or CA/T, to call it by its proper name, runs approximately eight miles through the heart of Boston, five miles of which are built underground while maintaining traffic on the elevated existing structure, while at its southern end I-90 is extended to Logan airport under active rail lines, Fort Point Channel and Boston Inner Harbor.Since the alignment of the road closely parallels the shoreline as it existed in colonial times, the cut and cover construction had to contend with substantial portions of filled ground, not to mention existing subway lines, live utilities, building foundations and, last but not least, the irritable Boston drivers and litigious adjacent property and business owners.Consequently, while it is impossible to single out the most difficult or challenging contract, the jacking of the tunnels of I-90 under the live rails of Amtrak certainly will rank high on the list.Never before, anywhere in the world, was an attempt made to jack tunnels of this size: the South Bay Interchange consists of three 78 feet (24 m) wide by 38 feet (11.6 m) high tunnels, the shortest of which is 167 feet (51 m) long. TECHNOLOGYIn order to achieve this engineering feat it was necessary to consolidate the soil under the track to prevent it from moving or settling during the jacking process. After a detailed analysis of the geological profile to be traversed it was decided that freezing was the most suitable method, since it could be applied to the full range of soils present on the proposed alignment."

Jan 3, 2003

By Nabil F. Ismael

Load tests were carried out to examine the ultimate bearing capacity of short, large diameter bored piles in connection with the construction of a multistory building on the Arabian Gulf in Kuwait. Testing included 0.45 m, 1.0 m, and 1.2 m piles installed through loose sand into a bearing stratum consisting of very dense cemented sands. All tests were carried out to failure. The base resistance and shaft friction were calculated using the Meyerhof method for a layered soil profile. The method employs the standard penetration test N-values. The results indicate that the piles are end bearing piles with a great portion of the pile capacity due to base resistance. The mobilized skin friction is small. The calculated pile capacities were very close to the measured values with the maximum difference not exceeding 10%.