Search Documents

By Robert C. Rabeler

Soil and Materials Engineers, Inc. (SME) has utilized drilled cast-in-place (D-CIP) piles on a number of projects in the midwest. These foundation systems have typically consisted of drilling an 8 to 9-inch diameter borehole with a rotary type drill rig or driving a casing with a small hammer. A structural steel member is installed in the center of the excavated space, and the borehole or casing is grouted to complete the installation of the D-CIP pile. This type of piling system has also been called: mini-pile, micro-pile, or drilled-in pier. The capacity of these piles varies depending upon subsurface conditions, as well as the structural capacity of the pile. The structural capacity can be modified based on the size and yield strength of the structural steel member. SME has used the D-CIP piles for underpinning of lightly-loaded structures for a number of years. Steel brackets can be welded to the structural steel member in the center of these piles, and the bracket extended underneath existing foundations to provide proper foundation support. D-CIP piles have also been used for new construction where access was limited. Recently, SME had the opportunity of providing design as well as construction monitoring services for a unique project where these piles were used, but at much higher capacity. The project involved adding seven additional floors on top of a five-story building (total of 12 stories). New columns were extended through the existing building to support the new floors. Access to construct foundations was available to one level of underground parking beneath the structure, as well as to a basement area. Access required equipment to travel through a 3-foot wide hallway. A special duplex drilling machine was used to access the foundation locations and to install the piles in a limited headroom condition. Eight-inch diameter D-CIP piles were extended to a depth of approximately 40 to 50 feet below grade and socketed into a dense clay till or sandstone, and No. 18 or No. 20 threaded bars were installed in the center of these piles. The design pile capacity was as high as 190 kips and were verified by a compression load test. The load test was performed with limited access and headroom. These piles were installed by Spencer White and Prentis Foundation Corporation (SWP). For conditions where rock or hard soils are encountered at reasonable depths, D-CIP piles can provide working load capacities comparable to larger driven steel piles. The ability of the equipment to access very restricted areas, combined with the high capacities results in a very attractive solution to a number of difficult foundation problems.

Jan 1, 1999

By Christopher J. Pacitto

This paper presents a case history of an engineered, monitored, and tested program that provided an effective and satisfactory basis for the completion of pile foundations for Twin Dolphins 1 at La Peninsula Condominiums located in the Isles of Capri in southwest Florida, U.S.A. An 8-story building (withl-story parking underneath) along with recreational facilities (such as a swimming pool and tennis courts) had been planned for final construction. Following an evaluation of various foundation alternatives, a precast prestressed concrete (PPC) pile-supported system was selected. The building foundations were designed for pile capacities of 445kN (50 tons) and 890kN (100 tons) in compression and 133kN (15 tons) in uplift. A test pile program was performed to provide site-specific pile driving data, verify design assumptions, determine production pile lengths, and evaluate pile driving criteria. A total of 24, 356 mm (14-in.) square, 19.8 m (65 ft) PPC concrete piles were driven and dynamically load tested utilizing a Pile Driving Analyzer (PDA) within the building limits. Dynamic monitoring during probe pile installation and restriking was performed to estimate the ultimate capacity of the piles and to evaluate driving stresses during installation. CAPWAP analyses were preformed on PDA data to better estimate pile capacity, resistance distribution, and predict pile freeze (increase in pile resistance with time) and thus optimized the production pile lengths. Upon completion of probe pile installation, 12 of the probe piles were tested using the Pile Echo Tester (PET) function of the Pile Integrity Sonic Analyzer (PISA). PET testing was performed to evaluate the integrity of piles which had exhibited high driving stresses during PDA testing. Information gathered during the probe pile driving program was effectively utilized as part of the overall quality control program to install a total of 539 PPC piles (including 24 probe piles) within the building limits at the project site to depths ranging from 9.1 to 19.8 m (30 to 65 ft) below the existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the CAPWAP analysis for probe piles. Use of geotechnical instrumentation and PDA assisted technology enabled each foundation support element to be constructed to its optimum capacity and at optimum cost. Furthermore, by using PDA the consultant was able to quantify a difficult to measure geotechnical phenomenon termed "pile freeze" which eliminated costly overdriving and unnecessary splicing of piles.

Jan 1, 2002

By Mike Muchard

Augered cast-in-place piles are one of the most cost effective deep foundation options available to designers but have been largely underutilized due to skepticism associated with quality assurance and hence capacity. When installed correctly, unit friction values can rival any other competing foundation system. To this end, many means have been implemented to increase confidence in the competence of the foundation. One such method is load testing via the Statnamic test method. This paper presents an overview of the Statnamic test method, advantages and disadvantages of its use, and several case studies where Statnamic testing of augered cast-in-place piles confirmed quality construction, brought about design changes, or proof tested problematic installations.

Jan 1, 2000

By Harald Ludwig

In 2002, excavation support work commenced on the Capitol Visitor Center project located adjacent to the nation?s Capitol building in Washington, D.C. The outlying work (Slurry Wall Work at Main Site is not discussed) consisted of providing excavation support for a new truck tunnel approximately 1900 feet long up to 50 feet deep as well as support for the new underground auditorium and Library of Congress tunnel. The excavation support consisted of a combination of conventional drilled in soldier beams, lagging, tiebacks and braces; intricate underpinning inside the existing Capitol building; support of an existing Russell Tunnel; soil nailing and tiebacks underneath the existing Russell Tunnel; two temporary bridges; and a deep soil mixed wall with lateral support provided by braces. As part of an on-going research program, some of these braces were instrumented with strain gauges. The deep soil mixed wall was approximately 300 feet long and 65 feet deep on either side of the truck tunnel. Approximately 34,000 sf of deep soil mixed wall, 90,000 sf of conventional excavation support, 200 braces, and 320 tiebacks were installed. This paper describes the large scope and breadth of the project that required a variety of excavation support techniques. A few of the challenges in designing and installing the support of excavation are discussed. This paper also presents the results of the instrumentation program conducted on the deep soil mixed wall, which stood open for more than a year.

Jan 1, 2006

By Harry K. Weatherbee

The paper presents a design case study for a four-story correction facility addition in south Boston, Massachusetts, supported on friction piles driven into the Boston Blue Clay. 356 mm (14-in.) square prestressed-precast (PSPC) concrete piles were selected as they were found more effective and economical. A static load test was performed where the pile was brought to "failure". The load test data were evaluated to estimate the Ultimate Pile Capacity as well as the Ultimate Unit Skin Friction (Adhesion) to serve as a design tool for friction pile projects in the south Boston Area.

Jan 1, 2003

GENERAL CONTRACTOR: ALEXANDER CONSTRUCTORS, INC. STRUCTURAL ENGINEER: CAGLEY & ASSOCIATES, INC. GEOTECHNICAL ENGINEER: F.T. KITLINSKI & ASSOCIATES, INC. PILE FOUNDATION CONTRACTOR: L.G. BARCUS AND SONS, INC. PROJECT PROFILE: 108-10 in. diameter AugerPiles installed to an approximate depth of 32 ft. Piles were installed through Stiff Clayey Fill and Medium-Dense Sands to Decomposed Shale. Piles were drilled to a refusal criteria of 1 ft. / 3 min. Piles were installed using a Barcus Mantis AugerPile rig which is large enough to install piles 25 to 50 ft. long outdoors. The Mantis is also ideal for indoor and low overhead installations. On top of being extremely versatile, the Mantis is also very economical to mobilize. The existing structure is supported on H-Piles. The AugerPiles were furnished and installed for less than the material price of the H-Piles. Design loads were under 40 tons which eliminated the need for a load test. AugerPiles were selected for minimal vibration, limited noise, and economy.

Jan 1, 2001

By Wesley Schmutzler

The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.

By Paikowsky, Samuel G.

"Due to the way drilled deep foundations are being constructed, their structural integrity and geotechnical capacity are highly variable. Drop weight systems are increasingly being used to dynamically test the capacity and integrity of drilled deep foundations. Conventional pile driving hammers are often either inadequate or not economical to test these foundations and drop weight systems have therefore been developed to allow for dynamic testing.The advantages of the tests include high mobility, short testing time, low cost relative to static load tests (allowing multiple tests at a single site), and integrity/construction quality evaluation concurrent with capacity determination. The dynamic testing method for drilled deep foundations encounter several difficulties including: the need for a pre-testing analysis for matching pile, soil and testing system, adequate mass and drop height to reflect the mobilized capacity without structural damage, test interpretations for irregularly shaped and/or non-uniform piles, need for reliable dynamic measurements depending on the impact and the distance between the impact and the measuring point, and limited knowledge about the accuracy of the predictions.The principles of the tests are presented using simplified models and demonstrated via a case history. Drop weight systems are reviewed. Dynamic measurement principles are explained and the construction and testing quality effects are outlined and demonstrated via numerical modeling and case histories. A comparison of dynamic and static tests is presented via a database, case histories and finally a short review of relevant codes is provided.1 IntroductionTraditional static axial load test is performed by a slow application of a force produced against independent reaction, imitating structural loading. It is the most reliable method to determine the pile’s performance as commonly required under typical service conditions. The major limitations of this testing are: (i) high cost associated with set-up, test duration, interpretation and construction delays, and (ii) inability to obtain information about the pile-soil interaction along the pile without additional testing means (e.g. tell tales, strain gauges, etc.). These limitations are acute when high capacity foundations are involved."

Jan 1, 2015

By Arpit Parikh

"Ground Water or Pore water pressure development in Sandy Soil formation is Critical situation in foundation analysis and design.Moreover it become severe while associated with higher liquefaction probability in river bank areas. It is difficult to find cost optimized solution for liquefaction mitigation under limited budget allocated for the project. Here in these research paper the attempt has been made to have clear picture of liquefaction by using various techniques and field tests. And its mitigation by suitable foundation type. In Bangladesh, On Bank of River Meghana, Power plant structures are proposed. The particular site is full of fine sand having partial silt throughout from EGL to 55 m depth. Hence in addition to Conventional Boring / Drilling operations, CPLT, SCPT, SCHT and PMT had been performed to arrive deterministic effect of liquefaction. By use of Geologismiki software and some excel based programs developed which indicates that Certainly liquefaction occurs under the event of earthquake. By Checking past records of Bangladesh we found, there are small magnitude earthquakes are inevitable and frequent. Hence fourth to overcome the bad effect of liquefaction, the deep pile foundation -Driven Pre Cast Solid Square Pile of 400 mm dia. had been suggested for various types of power plant structures. Which densify the soil and ground will improve in resisting liquefaction.1. INTRODUCTIONA Detailed Geotechnical/Foundation design Analysis had been done to arrive at optimum foundation design solution in highly probable liquefaction zone of Silty Fine Sand near Dhaka City of Bangladesh for proposed 750 MW Cyclic Power Plant. Hence about 24 no. of (Borehole) Boring and Drilling up to depth of 55 m from existing ground level has been carried out. Additionally, 09 nos. of Static Cone Penetration Test (SCPT), 02 Nos. of Dynamic Cone Penetration Test (DCPT), 02 Nos. of Pressure meter test (PMT), 02 nos. of Cyclic Plate load test (CPLT) of suitable capacity with 06 nos. of Seismic Cross Hole Test (SCHT) in boreholes had been carried out. The purpose of PMT and SCHT was to have clear idea about the Seismic behavior - knowhow of site. According to Basic principles of Soil Mechanics and foundation design, it is proved that PMT & SCHT are dynamic test. These tests stimulate field condition of occurrences of earthquake. In later stages of analysis, it is found that site have high probability of liquefaction through use of Geologismiki – Liquefaction Analysis Software. Author of these research paper also felt earthquake vibrations – strong aftershocks during site study where Epicenter of the earthquake was in Myanmar during month of august 2016."

Jan 1, 2017

By Sikko Doornbos

For the extension of the Paper Mill of Parenco in Renkum, the Netherlands, the application of a pile foundation was required. The demands for this pile foundation were very explicit a vibration free and soil displacing pile systems with low allowable settlement. Another important aspect was the total amount of piles (originally over 1600 auger piles) which had to be executed within 3 months, in very difficult and unhomogeneous soil. Based upon these conditions the Tubex Grout Injection Pile was chosen to be used for this project. This system involves the drilling of a steel tube with a conical pile shoe while grout is injected at the point simultaneously, creating a mixed-in-place layer around the tube. INTRODUCTION After extensive marketing, the board of directors of Parenco, decided to a large extension of the production capacity of its paper mill by building a new production building called Paper Mill 1 or PM-1. The new PM-1 extension had to be constructed beside the existing PM-2 because of limited terrain. The site is located right between the Rhine river and Renkum, approximately 15 kilometers (10 miles) west from Arnhem (see figure 1). The construction involved the building of the PM-1 extension of approximately 250 meters (820 ft.) long by 40-60 metres wide (130-200 ft.). The main structure was to be constructed of precast concrete beams and columns.

Jan 1, 1987

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By Y. G. Li

The design and construction of the hand-dug caisson pier foundation of the Shenzhen International Trade Centre are described in the paper. In addition discussions and inquires about the load-bearing capacity of the hard bedrock are offered.

Jan 1, 2010

By Hal W. Hunt

Heavier loading and more efficient equipment is helping to keep driven piles competitive in America. Better Knowledge and testing of soils and support materials make it practical to use higher stresses; this is being strongly promoted by those directly concerned with timber, steel and concrete piles. Readily available point protection is increasingly used to assure penetration of piles without damage to full load bearing capability. Fabric drains are being installed with pile equipment to speed consolidation of soils. Sheet pile configuration has changed; production has been reduced largely because of imports. Dynamic checking of representative piles for load carrying capability is replacing conventional load testing of just a pile or two ? at much lower cost.

Jan 1, 1987

By Mohammed Sakr

The use of helical piles for permanent foundation applications has become a practical and feasible alternative to the traditional cast-in-place concrete or driven steel piles. Research and development, installation equipment and manufacturing improvements in the helical piling industry have led to this trend. Moreover helical piles are typically smaller in size and weigh less than traditional piles, and require relatively smaller equipment and therefore it is a cost effective option. The latter is a very attractive feature for foundations installed in remote sites across Alaska. This paper presents full-scale pile load test results of helical piles and driven steel pipe piles installed in a site located in Anchorage, Alaska. Four full-scale pile load tests were carried out including two axial compression and two uplift load tests. Both helical piles and driven steel pipe piles were installed and tested at the same site under similar conditions to provide a direct comparison. The results of the full-scale load tests indicate the superior performance of helical piles compared to driven steel pipe piles. This paper describes the pile installation and test setup, presents the test data, and discusses the results.

Jan 1, 2009

By Dimitris Pachakis

In this paper, the authors give a brief overview of the current practice guidelines and tools for the seismic design of sheet pile quay walls, emphasizing how the design guidelines are lacking when the existing structure performance evaluation is required to meet performance-based criteria. Relying on recent experience they explain how the existing practices can be amended to focus more on performance evaluation as opposed to design. An example is given of an old sheet pile quay wall analyzed and evaluated for its performance according the recent performance criteria devised for Californian Marine Oil Terminals.

Jan 1, 2011

By Kenneth Gavin

Design practice for piles installed in Irish glacial till has developed in an ad-hoc manner, based on the results of un-instrumented load tests. This had led to designers using similar design parameters for both CFA and displacement piles. To address the concerns of industry a series of instrumented pile tests were performed by two Irish Universities. These tests summarized herein, revealed that CFA piles develop higher shaft resistance than piles driven in glacial till. However, they exhibit low base stiffness and the end bearing resistance that can be mobilized at acceptable pile settlement is low. The use of simple non-linear elastic design approaches to predict the load-displacement response is considered. The methods are used to predict the capacity of two large diameter CFA piles installed in glacial till. While the predictions were reasonably accurate at predicting the initial load-displacement of the piles, significant creep settlement developed at higher load levels. The cause of the creep settlement was investigated through the use of plate load tests and the consequences for pile design are discussed.

Jan 1, 2009

By R. J. Yan

There was a plant equipped with a 32000t Hydraulic Press to be built, under which a box foundation of 22.5m x 15m x 14.25m (depth) with a base slab of, varying thickness was proposed. The subgrade reactions, bending moments and settlements needed to be determined by means of in-situ model test. A model of the same materials as the prototype scaled to l/10 was embedded in-situ with simulated depth in the bedrock. A lot of data obtained from 39 bench marks, 32 elongation measuring points, 30 couples of electric resistance strain gauges and 24 pressure cells attached to the model foundation enables all the quantities required to be found out. Since it was put into operation, the settlements measured has reasonably agreed with the test results and the foundation has been in good condition.

Jan 1, 2010

By G. Price

The Building Research Establishment installed a base load cell in a driven cast-in-place pile prior to it being tested under vertical load. The monitored base loads were found to be significantly less than could have been predicted by current design methods. The less than expected capacity was attributed to the drilling out procedure. An electro-level system installed in a second similarly formed pile, provided detailed information on the performance of the pile under lateral load. The information obtained was used to check several current design methods for laterally loaded piles. The findings show the potential dangers of attempting to improve design parameters from only limited performance data.

Jan 1, 2010

By Chu E. Ho

Key variables that govern the jet cutting process are examined based on fundamental theories of jet hydrodynamics and soil mechanics. Under normal conditions of jet grouting operations, lift speed and rotation speed are found to be of less importance than the depth of jetting, nozzle pressure, nozzle diameter, and the soil bearing resistance, with regards to their influence on jet cutting distance. An analytical equation linking the governing variables is proposed, which allows for the possibility of evaluating column diameters achievable in different ground conditions based on theoretical calculations. When used in conjunction with shallow jet grouting field trials, the equation can provide a means for extrapolating trial results to conditions at actual depths for production jet grouting.

Jan 1, 2006

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2003