Search Documents

By Yvone Franco Crosato

The dense population of Hong Kong requires the construction of tall buildings in reclaimed areas or perched on the slopes of the many hills. The large loads to be supported are carried by deep foundations. Many of those are bored piles, to rock, of diameters up to the 3.0 m. of today.

Jan 1, 2000

By David Siu

Many problems were encountered with the mechanical wedge-type splices used for the 15-inch square precast prestressed concrete piles installed at an industrial plant site. Many of the wedges were breaking during installation of the splices and after pile driving resumed following splicing. Dynamic monitoring of the piles and uplift loading tests confirmed that the problems were associated with cracked or damaged wedges. More ductile, annealed wedges were subsequently used, and, while not completely satisfactory, they were found to perform better than the original more brittle wedges. Introduction Long precast prestressed concrete piles were installed to support heavy, settlement-sensitive structures at an industrial plant in Port Alberni, British Columbia, Canada. The piles were driven through soft compressible silts and clays to toe bearing in a dense sand and gravel deposit or on bedrock. Each pile consisted of two or three segments joined with mechanical wedge-type splices trademarked DYN-A-SPLICE. Shortly after construction began, problems arose during pile installation, and these problems were, later, identified to be related to the wedges, or clamps, used to connect the splice plates.

Jan 1, 1991

By Xu Ronglie

This paper looks back on the developments and achievements of deep foundations, on the basis of the complex geological conditions and environments in China. It sums up advances in theoretical and applied researches, engineering constructions, practical experiences, case histories, and problems and developing prospects of piles and deep foundations in recent years in China.

Jan 1, 1991

By Donald A. Bruce

Pin Piles are small diameter, bored, cast-in-place piles used to underpin structures. They were first employed over 40 years ago in Italy, and have been used in the U.S. since the late 1970's. However, it is only in the last few years that their full potential in terms of load holding capacity has been exploited: whereas 100 kip working loads typified former practice, ultimate loads approaching 700 kips have recently been recorded for Pin Piles founded in sand. In order to better understand the actual performance of these piles, fundamental research has been conducted by a consortium of industry and academia. This paper describes the advances made in the laboratory and full scale field testing programs. In particular, the extensive field tests have been conducted in a variety of materials in which different pile configurations have been cyclically tested to failure. By using this test method, the elastic performance of the piles has been examined and so the progressive interfacial debonding phenomenon has been studied. This has led to the development of the Elastic Ratio concept which is proving extremely useful in analyzing and predicting Pin Pile performance. Data are provided from the full scale Test Pile Programs conducted at Mobile, AL and Port Vancouver, WA. Given that Pin Piles are usually installed in areas of low headroom or restricted access, and through difficult, occasionally contaminated soils, the paper also describes key aspects of construction.

Jan 1, 1993

By Karen Dawson

Pressure-grouted helical piles support a new seven-story homeless housing center in the Coney Island neighborhood of Brooklyn, New York. The project team instrumented and statically load tested piles to as much as 1,000 kips (4.4 MN) in advance of construction to obtain the approval of the New York City Building Code officials and to verify the design. Use of pressure-grouted helical piles required additional design effort and time risk because of New York City's Construction Code Determination (CCD1) process, which is required for non- standard deep foundation types. Despite

May 1, 2022

By Sam X. Yao

The underwater concrete technology has historically evolved largely through a trial-and-error process of constructing marine works. Many outstanding examples exist of high quality concrete placed underwater. However, failures also occurred and led to excessive cost and/or schedule overruns. These failures were largely due to improper concrete mix design or improper placement. The problems may have occurred because proper underwater concrete construction techniques and experience have not been widely disseminated. This section focuses on technical issues of underwater concrete mix design, concrete production and placement, and quality control.

Jan 1, 2013

By Joel L. Volterra

Since 1910, Mueser Rutledge Consulting Engineers (MRCE) has regularly provided professional engineering services including inspection of pile load tests. Historically, such services included on-site inspection of the driving of test piles and subsequent static load tests by qualified Geotechnical Engineers. Load testing procedures are specified by local or State Building Codes, locally the 1968 Building Code of the City of New York (1968 BCCNY). Between 1968 and 2008, the 1968 BCCNY required a minimum 48-hour hold period for standard loads per pile type, an extended 96-hour hold period for higher capacity piles, and a settlement criterion that the pile maintain a test load equal to two times the design load with less than 0.012 inches of settlement over the last 48 hours of the hold period. Effective July 2008, the new 2008 BCCNY shortened the hold period and relaxed the settlement criteria to that which is more similar to other governing codes and standards such as the International Building Code (IBC 2006) and the American Society for Testing and Materials (ASTM). MRCE implemented an automated load test monitoring system to reduce costs and to alleviate or minimize overnight and off-hour staffing for load test readings. Initially, a series of linear variable differential transformers (LVDTs) and data loggers were included in the Contractor?s load test setup to electronically record pile head settlement and where applicable, settlement of telltales installed to varying depths in the pile. A pressure gage was subsequently added in the hydraulic line, then a load cell, strain gages, and remote access using modems. The ease of the setup and modular adaptive nature of this system have proven it to be a useful tool and improved our ability to better serve our clients and manage our pile load testing services.

Jan 1, 2008

By A. R. Gaba

Phase I of the Canary Wharf development in London's docklands involves the construction of six fifteen storey buildings located predominantly over water of the West India Docks. The buildings are supported on some 1000 No., 25m long, open ended steel tubular piles driven through 10m of dock water to found in dense sand at a depth of about 15m below dock bed level. The piles are of composite section with reinforced concrete within the upper 17m of the steel tube. Three trial piles were installed in the dock to investigate the driveability and performance of the driven steel tubular piles. The piles were subjected to dynamic and static load testing. Loads were applied in both vertical and horizontal directions. Vibrating wire strain gauges were installed on the inside of the steel piles, on the reinforcement and in the concrete to determine the relative proportions of the applied load carried by the steel tube and concrete infill and to establish how these proportions varied along the length of the piles. Inclinometers were also installed to monitor the lateral deflection of the piles. This paper describes the driving, construction and testing of the three trial piles. The results of the vertical and horizontal loading tests are discussed and comparisons are made between dynamic and static tests carried out on the piles.

Jan 1, 1989

By Kenneth A. Pidgeon

This paper presents a case history on mitigating vibration problems associated with the installation of steel sheetpiles. The project in-cludes installation of steel sheetpiles for a utility trench within 40 feet (12.2 meters) of a very sensitive manufacturing facility. Numerous production line quality control instruments and manufacturing processes within the manufacturing facility are extremely sensitive to vibrations. To minimize the impact to the owner, we specified that the contractor perform a vibration study using different types of pile hammers. The results and conclusions of the vibration study are presented in this paper.

Jan 1, 1995

By A. R. Katti

The stone columns are widely used in the improving the bearing capacity of weak soils mostly for supporting flexible foundation systems. The load carrying capacity of a stone column is complex in nature. The load capacity is derived from the lateral stresses acting on the stone column due to load transmitted from the flexible structure due to deformation to soil mass and which in turn transmits lateral pressure in s3 direction. The load capacity is also function of the f value of the stone column, cohesion of the surrounding soil, K0 and Gb2 of surround­ing soil including passive resistance developed to lateral deformation of the stone column. The assessment of axial and radial deformation is much more complex. Recently Katti et.al. have developed a method based on a granular heap approach and computed with equivalent fe. which combines the effect of s3a and equivalent volume concept to estimate radial and axial strains. In this paper an attempt is made to put forward guidelines for design of stone column accounting for both stability with respect to shear and also with respect to settlement. The estimate of settlement are based on the internal properties of stone column and surrounding soil. It is considered thus the settlements computed are more realistic.

Jan 1, 1996

By D. Waite

The Chairman opened the session by wondering why so few papers on Maritime Structures had been received for this conference. Perhaps because the marine environment is so hostile and the access so difficult that engineers tend to be more prudent about new ideas and designs. Dennis Waite noted the number of grey hairs in the room - grey hairs which could be equated with experience gained the hard way. He hoped that this experience would be passed on in the discussion period of this session. The Chairman was delighted to welcome two authors from China, Mr Sun and Mr Liang. He was most grateful on behalf of the conference for their efforts both in preparing their papers and for being able to present them. He regretted that Messrs Noce and Fedolino were not able to present their paper and then welcomed Mr Christensen from Denmark who would present the first paper.

Jan 1, 1991

By Mohab Sabry

Pile foundations are used extensively around the world to support both inland and offshore structures, including important structures such as nuclear plants and oil drilling platforms. The limit of the pile depth is currently predicted during the pile deriving process, given no chance for the designer to predict accurately the capacity of these piles prior installation. Furthermore, after pile installation, designer may not be able to modify the pile group design by increasing the number of piles and or changing the geometry of the pile group. This paper presents a numerical model for the case of single piles driven in homogenous sand using finite element technique and the theory of cavity expansion. The model is capable of simulating all the construction stages of concrete piles up to the maximum depth, which can be driven in sand and accordingly the capacity, which can be attained by these piles. The program "PLAXIS" is used to perform the proposed analysis. This model simulates the process of pile driving in terms of the changes in the earth pressure and the overconsolidation ratio acting along the pile's shaft. Based on the results of the present investigation, these depths can be predicted based on the pile geometry and the sand properties. Charts are given to provide these depths for given pile/soil conditions.

Jan 1, 2006

By S. X. Liang

In China, the bearing capacity predictions of the pile with Stress-Wave Theory have been developed rapidly in recent years. This paper recommended a DZH-3 Pile Driving Analyzer and its relevant computer programs. Taking Qinghai Hotel Project for example, it gave their applications in the dynamic tests of large diameter cast-in-place piles.

Jan 1, 2010

By George Mylonakis

The curvatures and subsequent bending imposed to piles by the surrounding soil during the passage of strong seismic waves is studied. This type of bending develops even in the absence of a superstructure and is referred to as "kinematic bending", to distinguish it from bending imposed to piles by loads generated from the inertia of the superstructure ("inertial bending"). Although kinematic loading may be severe in the presence of sharp stiffness discontinuities in the profile and may lead to damage, it has received little attention by engineers. The scope of the paper is twofold: (i) to discuss some fundamental aspects of seismic pile bending, and (ii) to review some existing design methods. To this end, a dimensionless bending strain parameter (instead of the more commonly used bending moment), and a strain transmissibility function relating pile bending strain and corresponding soil shear strain are introduced. Numerical examples are also presented.

Jan 1, 2002

By Tomohiro Yamasaki

"At the pre-construction foundations of the controlled waste disposal site built at the Port of Kinuura, the clayey soil account for the most, and with lesser amounts of sand compaction piles and sand mat. The cement deep mixing method (CDM) was used to improve ground impermeability and to reinforce the foundations on the seawall. Laboratory mixing and testing was performed to determine the appropriate quantities of cement additive for clayey soil, SCP sand, and sand mat. The test results indicated that maintaining the design strength of qu = 1,550 kN/m2 would require C = 100 kg/m3 of cement additive for all three soil types (clayey soil, SCP sand, sand mat). The permeability performance needed to improve ground impermeability assumes a permeability coefficient of K = 1.0×10-6cm/s. And the clayey soil satisfied the performance requirements at C = 100 kg/m3. However, to improve grand impermeability of the SCP sand and sand mat required more than 5% of particles having diameters of less than 75 µm. Thus, in the latter two cases, the required cement adding quantity was C = 250 kg/m3. The test specimens at one to two weeks after the created with a permeability coefficient of K = 10-6cm/s became permeability coefficient of K = 10-7cm/s six week later due to the effects of cement solidification. So the permeability coefficient declined about one order. The permeability coefficient three months later tends to decline continued with a somewhat lower.INTRODUCTIONBetween 2008 and 2011, the Aichi Seaside Environment Center constructed the Kinuura No. 3 offshore controlled waste final disposal site at Taketoyo in Aichi prefecture. (see Figure 1). The disposal site offers a landfill capacity of 5.21 million m3 and measures 472,000 m2 in area, of which some 344,000 m2 is a managed controlled sector enclosed within an impermeable seawall."

Jan 1, 2015

By A. B. Desai

The construction of 1144 nos. of piles, each 1.5 m diameter, bored-cast-in-situ type and varying in depths from 6.5 to 23m, has been completed as foundation for 26 piers of 548 m long aqueduct across Orsang river to carry 1128 m3 water of Narmada Main Canal of the Sardar Sarovar Project in Gujarat. These piles are socketed 1.5 m into foundation grade rockmass. The portal system of 44 nos. of piles and pile cap at the top for each pier is analyzed considering the portal fixed at bottom of piles. The borings for pile shaft were done deploying reverse mud circulation rigs and also by conventional chiseling and bailing operations. Besides vertical loading tests and lateral loading test on piles, dynamic tests such as low strain integrity testing on 290 piles and high strain pile testing on 17 piles were also conducted. The results indicated that (a) the settlement/ displacement are much less than the prescribed limits (b) good quality of concrete (c) piles are firmly socketed and (d) piles have adequate structural capacity to withstand the design load.

Jan 1, 1996

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006

By Sun Shao Xian

The Port of Shekou is situated at Shenzhen Bay on the east side of the Pearl River estuary. Geological condition of the site is quite complicated. On top of the sea bed, there is a layer of soft silt 8 - 14 m thick. Under the soft silt, there are intercalated layers of sand, silt and clay. Average surface elevation of the underlying undulatory weathered bed rock is about - 20 m, with a variation of about 10 m. In certain locations, the weathered bed rock is covered with a layer of silt 3 - 4 m thick. This paper gives brief account of three types of wharf structures which are of particular interest, constructed in the last few years: (A) Platform type wharf structure with frontal sheet piling and steel raking pile in the rear; (B) Relieving Platform type structure with steel sheet piling and inclined anchoring HP pile ; (C) Steel pipe pile row supported apron added to a marginal quay. Average construction time of a deepwater berth is about six months.

Jan 1, 1991

By Dennis Wrixon

It was a little bit exceeded. The decision was the uniform settlement is measured at each one corner and the highest one corner is the important one. And in addition there is a differential settlement of 2.1 mm allowed. So we reached about 7.8 or 7.9 mm with the highest corner and in addition 2.1 so it was a little too much. But behind there is a very difficult calculation of the authorities where all of the displacements are combined together and there are of course some more factors of safety in these settlements.

Feb 10, 2003

By T. Jason Hardell

The Victory Bridge project was contracted by the New Jersey Department of Transportation. The project included the construction of two 4000-ft precast segmental concrete bridges to replace the existing Victory Bridge that was built in the 1920's. The existing bridge was a swing span bridge that was in desperate need of replacement. The project was considered high priority due to the large maintenance costs to keep the swing span operating over the busy navigational channel. In March of 2003 construction began on the first bridge and by April of 2005 all of the segments were set for the second bridge. On September 5 of 2005 the second bridge was open to traffic. The total cost of the project was $110-million. The two new bridges required the construction of 24-eight foot and 32-six foot diameter-drilled shafts with rock sockets. All of the shafts were constructed in the tidal Raritan River working from barges. What will follow is a description of the construction techniques that were used to build these drilled shafts, the anticipated and unanticipated challenges that were encountered during the project, and the lessons learned.

Jan 1, 2005