Search Documents

By Challa Venkata Rami Reddy, Anindya Roy, G. R. Konni

This paper presents the results of pile lateral capacities obtained from both conventional design and fullscale pile lateral load tests. Conventional design using P-Y curve analysis is very commonly being used by designers; designers use well accepted software programs like Lpile and Allpile for analysis. However, these programs do not cover the soil models to simulate engineering behavior of marine carbonate sands; which generally have different engineering behavior than silica/quarts sands. In this study, the existing soil models for common sands have been used to assess pile lateral capacities and these results are compared with the results from full-scale instrumented pile lateral load tests performed in compacted marine carbonate sand fills of artificial island constructed for oil and gas facilities in Abu Dhabi. The objective of this study was to verify the applicability of the existing sand soil models for carbonate sands and also to verify the associated conservatism in the pile lateral capacities. This study shows that the actual pile lateral response is much stiffer than what was anticipated through the LPile analysis. Therefore, further research focus may be required to capture the engineering behavior of the marine carbonate sands to develop specific P-Y curves.

Sep 8, 2021

By Bernard H. Hertlein

Transportation system structures have come under very close scrutiny in the last couple of years, largely due to the damaging effects of disasters, both natural and man-made. In the Pacific northwest and California, earthquake risk is a major concern. In the central and eastern states barge impacts on bridge piers and docks are a big worry. In all cases of bridges over water and waterside structures, scour is a primary concern. Some of the results of this scrutiny have been changes in design and construction methods, and the introduction of more testing to supplement field inspection during construction, and throughout the service life of the structure. Future construction of bridges and docks will almost certainly see a continuing growth in these practices. Where foundations are concerned, particularly for bridges and waterside structures, many state and local authorities have started specifying drilled shafts rather than driven piles. Where the shafts must be constructed under water or slurry, visual inspection of most of the work is impossible, and one of several different Nondestructive Tests (NDT) is often specified. Contractors' experiences with these methods have varied considerably, and there is a great deal of controversy in the deep foundation industry over the reliability of NDT methods for assessing the integrity of foundation shafts or piles. The author has had more than 15 years of practice with the various NDT methods for deep foundations, on projects all over the US, particularly foundations for bridges and dock structures, and has developed an understanding of the "NDT controversy" as it has become known. In particular, experiences in the Pacific Northwest, California, and Alabama have illustrated the reasons for the controversy. This paper reviews these experiences, and suggests some steps that owners and contractors can take to reduce the risk of inconclusive or downright inaccurate test results.

Jan 1, 1998

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By R. Lee Wooten, David R. Shields, Darren D. Clark

"Borehole permeability tests that measure flow or head changes in boreholes located within seepage barrier walls are commonly used to estimate the in situ permeabilities of those walls for quality control and assurance. The current state of practice for estimating permeabilities from these barrier wall borehole tests is to use equations published by M. J. Hvorslev in 1951. Hvorslev’s borehole test equations model an infinite stratum of uniform permeability, which is not the actual condition for a test performed in a low permeability barrier wall located within a high permeability stratum. We examine and develop alternative equations based on line source analytical models, which more closely match barrier wall test conditions. We describe how these alternate equations can be used to estimate barrier wall permeabilities from borehole tests and compare the results to those obtained from the Hvorslev models. We also provide recommendations that consider differing upstream and downstream water levels.Barrier Wall Permeability Tests - State Of PracticeThe installation of seepage barrier walls has become more common in a variety of applications ranging from dams and levees to contaminated sites requiring retardation of groundwater flow. The types of seepage barrier walls and installation methods include soil-bentonite, soil-cement-bentonite, concrete, self-hardening slurry, geomembranes, and sheet piles, installed with various soil mixing, slurry-supported trench, and driving methods.Owners and contractors have used a variety of methods to evaluate the permeability of these seepage barriers. The following table lists commonly used quality control/assurance tests for evaluating the permeability of a seepage barrier."

Jan 1, 2016

By Athena C. Denivo, Pablo V. Lopez, Sissy Nikolaou, Alfred H. Brand, Ahmad Rahimian, Rudivien G. Josef

"The United States Tennis Association (USTA) Billie Jean King National Tennis Center (BJKNTC) site is located in the northeastern portion of the Flushing Meadows Corona Park area of Queens, N.Y. The site occupies some of the most difficult subsurface conditions for construction in the New York City (NYC) metropolitan area, with unique challenges from geotechnical, seismic and foundation design perspectives.At the USTA site, Paleozoic crystalline bedrock is found at a depth of roughly 300 to 400 ft (90 to 120 m) below grade. The geologic history of the site is complicated, starting from the early Pleistocene, when the ancient Hudson River temporarily changed course, flowing across Queens enroute to the Atlantic. It eventually carved a deep valley through the Cretaceous soils, in some places all the way down to bedrock. A series of glaciers advanced and retreated across the region during the Pleistocene times, filling the deep valley with layers of assorted glacial soils. At its southern edge, the last major glacier to flow across the region built up a ridge at the southern tip of Flushing Meadows known as the Harbor Hill terminal moraine. This ridge blocked the valley forming a dam, so as ice started melting away the valley filled up with a lake fed by glacial meltwater. Layers of clean outwash sand and varved silt and clay filled the glacial lake. The ice did not retreat in a steady manner, instead periodically readvancing over the previously deposited soil in the lake, then retreating far enough to let the lake drain temporarily into Long Island Sound, before readvancing again.As a result of this repeated sequence of retreat, advance, retreat, etc., there are places where a “crust” of desiccated soil formed when the lake drained, and areas with interlayers of outwash sand where ice readvanced into the lake. When the ice melted north of Long Island Sound, the glacial lake filling Flushing Meadows drained forming Flushing Creek. During the Holocene (roughly the last 11,000 years), as ice melted further away and sea-level rose, low lying areas filled with river sands and marine clays, along with coastal marsh deposits. Table 1 lists the soil design properties on site and Figure 1 exhibits the geologic section across the site."

Jan 1, 2015

By Travis A. Shoemaker, Mitchell S. Youmans, Nancy T. Chin, Michael S. Senior

A geologic assessment and stability analysis of the right abutment of Boundary Hydroelectric Dam in Pend Oreille County, Washington was completed in May 2017. The stability analyses identified a potential failure plane of a rock block that supports a bridge abutment, and weight restrictions were established to reduce the bridge loads. To restore full use of the bridge, a long-term stabilization solution was designed. A two-phased construction approach was implemented to reduce risk: (1) cable lashing and wire mesh and (2) 24 permanent post-tensioned tiebacks. The tiebacks were located and sequenced based on stabilization effect and site access to incrementally ease the bridge loading restrictions throughout construction. Due to weight restrictions and site tolerances, all work was performed with rope access construction methods. The contractor’s means and methods, tight drilling tolerances, and an exploratory adit within the rock block made the construction uniquely challenging. Due to limited exploratory data and irregular rock face geometries, the design orientation, location, and tolerances of the tiebacks were established in a 3D Building Information Model (BIM). The 3D model was revised frequently during construction to 1) model the as-drilled conditions of the tiebacks; 2) compare with the remaining proposed anchors; 3) anticipate the contractor’s sequence to reduce risk during drilling; 4) accommodate the contractor’s requests for information; 5) make design changes based on field observations; and 6) incrementally assess rock block stability. The 3D model was created using BIM software and automated using custom programming to link per-plan, proposed, and as-installed tiebacks between the 3D model, field logs, and a stability analysis. This system allowed for a near real-time 3D model and stability analysis, which were easily communicated between the design team and field staff. This workflow and automated model nearly eliminated manual editing of the 3D model, accelerated contract document response time, and helped reduce risk for the owner, contractor, and engineer. Here, we present a successful case study utilizing the Observation Method and a real-time 3D model to complete a project with numerous complexities relating to design, communication, and risk.

By Jeremiah M. Jezerski, Russell H. Lutch

The Mount Olivet Road Drop Shaft (MOR-DS) support of excavation (SOE) is a circular unreinforced concrete shaft with an inside diameter of a 30.5 ft (9.3 m) and depth of 120.5 ft (36.7 m), constructed using slurry wall methods. The SOE for the adjacent Mount Olivet Road Approach Channel (MOR-AC) and Mount Olivet Road Ventilation Vault (MOR-VV) near surface structures (NSS) consists of lean mix concrete walls and cement-bentonite walls, respectively, both constructed using slurry wall techniques and reinforced with embedded soldier piles. NSS SOE required multiple levels of preloaded internal bracing, with excavation depths of up to 75 ft (22.9 m). The original design construction sequence for the shaft and NSS SOE required that the MOR-DS be constructed in its entirety and backfilled to ground surface prior to excavation of the adjacent NSS SOE. After installation of the drop shaft and NSS SOE an accelerated construction sequence was implemented requiring the analysis of the excavation support systems to determine if the excavations could be open concurrently without adversely impacting the partially constructed permanent MOR-DS structure. The MOR-DS was analyzed using the finite element analysis (FEA) software, MIDAS GTS, to demonstrate that the unbalanced loads applied to the MOR-DS composite structure due to the revised sequence would not exceed the strength and serviceability requirements per ACI-350 or superseded by the more stringent project requirements. The results of the FEA were used to set limits for geotechnical instrumentation consisting of strain gauges located on the brace levels of the NSS SOE. A comparison of the SOE design hand calculations, FEA model results and instrumentation data is presented.

Oct 1, 2022

By Musbah A. Hasan, Ahmed M. Nasr, Fauzi Jarushi

Many transmission towers, high-rise buildings and bridges are supported by piles. These structures may be subjected to large lateral loads. Therefore, experimental investigations on model piles under lateral loads were conducted in uniform dry sand. Small-scale model tests were carried out considering the influence of pile length, pile diameter, sand density, roughness of pile surface and vertical load on the lateral resistance of a pile. Furthermore, the effect of pile load eccentricity (e/L) on the ultimate lateral resistance was studied. Investigations, of the influence of various parameters on the magnitude of the coefficient of subgrade reaction (nh), were also performed. It was found that the lateral load capacity of piles increases with increase in pile length, pile diameter, pile surface roughness and increase in the sand density. The results also showed that the coefficient of horizontal modulus of subgrade reaction, (nh), decreases with deflection increase. From the results, the coefficient of subgrade reaction for a smooth pile embedded in medium dense sand would decrease by (134%) when the lateral pile head deflection (yg) changes from (2% to 5%) of pile diameter.

Jan 1, 2017

By Gregory J. Canivan

Three test pile programs were conducted in Charleston, South Carolina to evaluate differences in bearing resistance due to installation methods. The tested piles were installed with impact hammers and vibratory drivers through soft clays and/or loose sands into the Cooper Marl, a stiff calcareous marine clay or silt. Piles driven into the Cooper Marl experience significant capacity gain with time following initial installation due largely to pore pressure dissipation. Pile size and pile type were both known to affect pore pressure generation during installation and subsequently the capacity gain with time. The test programs were primarily conducted to optimize pile design values and construction methods with regard to trestle construction but the results also contribute to the understanding of driven pile behavior. High strain dynamic testing was performed on several open-end pipe and H-piles. The measured difference in long-term bearing capacity of the H-piles as a result of the two installation methods was negligible, while the short-term bearing capacity of the pipe pile was larger when the piles were installed using impact hammers. The lower short-term resistance in the vibratory driven piles is attributed to larger excess pore pressures generated during installation compared to those generated during impact driving.

Jan 1, 2002

By Alper Turan

The use of aggregate pier foundation systems has become widespread as the engineering practice moves towards cost-effective ground improvement solutions that provide accelerated construction schedules. Increased bearing capacity, effective settlement control and potential for liquefaction mitigation are commonly acknowledged benefits of aggregate piers. This paper studies the mechanisms by which aggregate piers interact with each other and with the surrounding ground when excited by seismic loads. A particular emphasis was placed on the response of a raft foundation supported on a site improved using aggregate piers. Three-dimensional nonlinear finite element analyses were conducted using commercial software package, ABAQUS. Non-linear soil behaviour is modelled using a three-dimensional total stress-based bounding surface plasticity model, which is able to simulate stiffness degradation and damping increase in the soil. The soil stratigraphy considered in this study was a 30 m deep soil deposit that comprised a very stiff base layer and a shallow soft surficial clay layer. Ricker Wavelet time histories with different frequency contents are used as the excitation force in the analyses. Various area replacement ratios (ARR) for aggregate piers are studied for a square plan layout. The results presented in this study are considered to be of interest to researchers and designers in evaluating the seismic ground response of the sites improved using aggregate piers.

By Shaw-Shong Liew

This paper presents the design concept using floating piles to support 2500Ton oil storage tanks on a very soft alluvial clayey soil of about 40m thick in Riau Province of Sumatra, Indonesia. The floating piles of various penetration lengths were designed to support seven numbers of such storage tanks seating on a 20m diameter and 500mm thick reinforced concrete (RC) circular raft. The pile points have been strategically located at the RC raft. Varying pile penetration lengths have been designed to minimize the angular distortion of the thin RC raft and the out-of-plane deflection at the tank edge. Vibrating wire strain gauges were installed at different levels inside the ø350mm prestressed reinforced concrete piles to measure the load transfer profile during the static load tests and water-loading test. The installation and interpretation of the instrumentation are described and discussed. Boreholes, in-situ tests like piezocones, vane shear tests and standard penetration tests, and laboratory testing were carried out to obtain geotechnical parameters for the pile designs. Static load tests were also carried out on the spun piles of varying lengths of 24m, 30m and 36m respectively. It has been demonstrated that the floating pile system can be a cost effective design to support heavy structures on very soft compressible deposits with satisfactory performance. Finally, the design concept validated with the results of instrumentation is discussed.

Jan 1, 2002

By Robert R. Morrison

Alberta Piling Contractors very rarely are required to perform major marine construction in the prairies, so it became as a big surprise to AGRA Foundations Limited to be invited by Transalta Utilities Corporation to bid on a major marine project for the Sundance Cooling Pond Expansion at Lake Wabamun, Alberta. Even more of a shock, the work had to be undertaken during Alberta's harsh winter conditions with temperatures plunging to -30 C. Not a happy situation for prairie construction workers to be in, working from barges in the middle of a lake in the dead of winter. However, it is well known that prairie boys make the best sailors.

Jan 1, 1997

By Alper Turan, Hesham El Naggar

"The use of aggregate pier foundation systems has become widespread as the engineering practice moves towards cost-effective ground improvement solutions that provide accelerated construction schedules. Increased bearing capacity, effective settlement control and potential for liquefaction mitigation are commonly acknowledged benefits of aggregate piers. This paper studies the mechanisms by which aggregate piers interact with each other and with the surrounding ground when excited by seismic loads. A particular emphasis was placed on the response of a raft foundation supported on a site improved using aggregate piers. Three-dimensional nonlinear finite element analyses were conducted using commercial software package, ABAQUS. Non-linear soil behaviour is modelled using a three-dimensional total stress-based bounding surface plasticity model, which is able to simulate stiffness degradation and damping increase in the soil. The soil stratigraphy considered in this study was a 30 m deep soil deposit that comprised a very stiff base layer and a shallow soft surficial clay layer. Ricker Wavelet time histories with different frequency contents are used as the excitation force in the analyses. Various area replacement ratios (ARR) for aggregate piers are studied for a square plan layout. The results presented in this study are considered to be of interest to researchers and designers in evaluating the seismic ground response of the sites improved using aggregate piers. INTRODUCTIONThe schedule and cost limitations imposed by the traditional over-excavation and replacement method for the stabilization and settlement control for poor soils resulted are underlying factors for the significant increase in the use of aggregate pier foundation system, particularly in the last two decades. Various well known advantages of aggregate pier systems including increased bearing resistance, settlement reduction, and increased uplift capacity have been studied by various authors. The use of aggregate pier systems for settlement control in soft soil deposits was studied by various researchers including Lawton and Fox (1994), Lawton et al. (1994) and Wissmann et al. (2001). Lien and Fox (2001) studied the behaviour of aggregate pier systems supporting embankments and retaining walls. The stabilization of slopes by means of aggregate piers was studied by Lien and Fox (2001), Wissmann et al. (2002). Thompson et al. (2009) reported on a performance monitoring study of aggregate pier systems supporting MSE walls. The interaction mechanism between the aggregate pier system and the surrounding soil attracted attention of various researchers. Handy and White (2006a) and (2006b) studied the changes that occur less than 2 m from centers of the piers, and further away, respectively. The support mechanism of aggregate pier systems subjected to compressive loading were studied experimentally and numerically by White et al. (2007) and Pham and White (2007), respectively."

Jan 1, 2017

By Hyunsuk Yoon, Kiho Lee, Juhyng Lee, Younghoon Jung, Junboum Park

"The environmental double pile method is presented as a device to improve the engineering properties and to clean up contamination of low-permeability soil. This method is one of the novel technologies based on the concept of one step process. It can be applied to low permeable contaminated ground for site reuse. It uses piles to improve drainage, contaminant remediation, and bearing capacity of the ground. To evaluate the on-site applicability of this technology, drainage and strength properties of the environmental double pile were assessed by a series of experiments and numerical analysis. Environmental double pile was found to be a feasible alternative method to improve contaminated soft ground.Korea is a peninsula with many coastal industrial zones. These zones are located in regions mostly underlain by soft ground with low permeability and adjacent to industrial areas that can be contaminated. Therefore, a new region-specific remediation method is required to achieve environmentally sustainable development. This research introduces the Environmental Double Pile (hereinafter, refer to as EDP) for the lowpermeability contaminated ground and focused on both contaminant remediation and soft ground improvement. Basically, the EDP is quite similar to sand compaction pile (SCP). The SCP has been studied extensively to improve soft ground (Braja 1999; Hansbo 1994; Madhav and others 1978; Taylor 1948). But unlike SCP, EDP is filled with oyster shells instead of sand and an inner pile is inserted in the center of this oyster shell filled-zone. Therefore, it is a double pile consisting of the oyster shell pile and the inner pile, as depicted in Fig. 1."

Jan 1, 2005

By Mihir B. Roy

"Coal transported by rail for Thermal Power Plant in Haldia, West Bengal, India, was to be received and stored in Coal Complex comprising of Wagon Tippler, Track Hopper, Junction Houses and network of horizontal and inclined tunnels. The site was very soft with high ground water level. Deep excavation and dewatering posed great difficulty. Original plan was to drive about 1000 m of steel sheet pile and well sinking which had major impact on cost and time. High ground water was identified as the main problem. Controlling water level and maintaining it would allow open excavation over major areas. Scheme for lowering aquifer with one and two-stage well-point dewatering system was developed following basic principles of groundwater and seepage. Arrangements of wells, installation and pumping were worked out in detail. Water levels could be lowered below bottom levels of excavation. Design of sheet pile was modified under lowered ground water condition. Overall length and depth of sheet pile were reduced drastically. Open excavation was possible in segments over major areas. The scheme was highly successful in smooth and fast progress of underground works. The works were completed safely months ahead of schedule time and with significant saving in cost.INTRODUCTIONThe Coal Receiving Complex of thermal power plant comprised of 250 m long 8 m deep Track Hopper (TH), 12 m deep Wagon Tippler (WT) with provision for addition of another Wagon Tippler. Track center lines of TH and WT were very close. Coal unloading facilities were connected with a network of underground tunnels and Transfer Points (TP) upto Pent House (PH). The facilities were optimized in a compact layout within about 400 m x 120 m area. Initially excavation for TH was started adopting side slope of (1 V : 1.5 H) with 2 m wide berm and dewatering by in-pit sump and pump. When depth of excavation reached about 5-6 m, failure occurred over a long stretch as shown in Figs. 1a - 1b photos. Further work was stopped to develop scheme for carrying out deep excavation and civil works safely."

Jan 1, 2015

By Adrian M. Keller

Borehole televiewers are downhole inspection devices available for high-resolution imaging of a borehole wall following rock coring. Borehole televiewers should be considered by geotechnical engineers and geologists as a supplemental way of investigating rock for deep foundations. The optical televiewer (OTV) produces a digital optical image and the acoustic televiewer (ATV) utilizes reflected acoustic waves to produce images of the borehole walls. These devices can be utilized to examine soft or fractured zones in the rock mass, solution features, open joints or other voids not observable from traditional rock coring techniques. These devices along with computer post-processing can determine the strike and dip of joints, bedding planes, shear surfaces, or other structural features, eliminating the need for expensive oriented cores or manned downhole logging. An acoustic televiewer was utilized in the Fall of 2008 during the investigation phase for the I-70 New Mississippi River Bridge (I-70 MRB) in St. Louis, Missouri. Voids and fractures in the upper portion of the rock were described by prior consultants. Further investigation of these features was necessary to evaluate deep foundation options to support the main towers. Ten borings were drilled from a barge in the river at the two main tower pier locations. An ATV was utilized in each of the ten borings to produce images of the rock mass in the borehole and allow further investigation of the voids. Voids interpreted as solution features were readily identified in the ATV logs in multiple borings and at similar elevations, suggesting connectivity. Measurements of the voids? width, location in the borehole and orientation allowed a more thorough understanding of the potential impact the solution features may have on the planned deep foundations. An extensive grouting program was eliminated based on the ATV results.

Jan 1, 2010

By Alexi J. Neill

"This presentation will showcase two challenging projects with deep excavation support systems in the Atlanta area where state-of-the-art instrumentation and monitoring systems were used to manage risk by confirming design performance requirements / calculations during construction. The instrumentation and monitoring system successfully reduced risk by recording real-time data on a project website while simultaneously sending email alarms to key site personnel when data exceeded pre-determined alarm thresholds. The monitoring data revealed unexpected performance at an early enough stage so that contingency plans could be engaged and remedial efforts devised in order to limit the consequences. Finite element analysis was used to model deformations, analyze the unexpected performance, and prepare theremedial design.INTRODUCTIONConstruction in densely populated urban areas is becoming more common in order to keep up with the increasing infrastructure demands of our growing population. America’s big cities continue to outpace the overall nation in population growth. The city of Atlanta, the nation’s ninth largest city based on metropolitan population, is a prime example of this. The population has grown at a rate of 6.6% between 2010 and 2013, nearly triple the overall growth rate of the United States during the same period (SustainAtlanta, 2015).As a result of increasing infrastructure demands in Atlanta, developers are now constructing larger buildings on smaller properties. In addition, developers are attempting to maximize space on their selected properties, often by designing underground parking garages to accommodate as many cars as possible on these compact sites. In some cases the selected sites are adjacent to buildings, utilities, and other existing structures. The risk associated with construction increases during underground work that requires a support of excavation system, particularly on confined sites adjacent to existing structures. There is a risk posed to people, property, and the environment that the project team should monitor when constructing in these conditions."

Jan 1, 2016

By W. J. Kingwell

Where the equipment, technique and materials are available for the construction of large diameter rock socketted piles, this is frequently the most economical and environmentally acceptable method of supporting very large concentrated foundation loads in geoglogically appropriate areas. This paper outlines the current approaches in Australia to design and installation of large diameter rock socketted piles. The equipment and procedures described generally reflect those developed or used by Vibro-Pile (Aust.), a company which, while installing the usual range of driven and bored piles, specializes in the design and construction of large diameter rock socketted piles and possesses special expertise in drilling in high strength rock. A high capacity crane attached drill for large diameter drilling in rock is briefly described. Discussed in detail are the construction techniques employed and structural and geomechanical design methods adopted.

Jan 1, 1989

By Niels Krebs Ovesen

Close economic cooperation was established among the countries in western Europe during the seventies. As a consequence, among others, a need for harmonized technical specifications for civil engineering works arose. Technical specifications for design and execution of building and civil engineering structures exist in most of the European countries. In some countries such technical specifications are part of the building regulations and in other they are independent codes of practice and standards. The works on the Eurocodes was initiated by the Commission of the European Communities about 1976. The Eurocodes are intended as common unified design codes for different load bearing structures constructed from different materials. They are also intended to cover design of geotechnical structures. They are established with a view to promote the free movement of goods and services within the member states of the European Community - the so called Internal Market - and within the member countries of the European Free Trade Association, EFTA by removing obstacles arising from different rules for calculation and design.

Jan 1, 1994

By Tai Luu, Michael McNicholas, James C. McIntyre

The Jersey City Municipal Utilities Authority (JCMUA), discovered that an existing sewer pipe had collapsed under the New Jersey Transit Conrail Railroad between Pine Street and Ash Street in Jersey City New Jersey. Immediate action was taken to abandon the pipe in place and install a new sanitary sewer. The borings showed 10-20 ft (3.04 m.- 6.09 m) of competent fill overlaying approximately 8 ft. (2.44 m.) of compressible peat and organics. Groundwater was at 8 ft (2.44 m) below ground level. The poor condition of the soils at subgrade could not withstand the extreme weight of the jacking machine or the thrust force required to push the casing from the launching pit to receiving pit. The support of excavation (SOE) would therefore not only need to retain the soil to allow the jacking equipment to reach subgrade at 14 ft (4.27m) below working grade, but also the back wall of the SOE would need to be sufficiently robust to function as the reaction block for jacking operations. The alignment and allowable tolerance for the jacked casing was minimal, therefore the performance of the SOE was extremely critical to the success of jacking operations. This paper will discuss in detail the design concepts that were developed and implemented by the team to overcome these obstacles. HISTORY The discovery of a collapsed section of an existing sanitary sewer led the Jersey City Municipal Utilities Authority to act on an emergency contract. The project design team was tasked with developing an abandonment plan for the broken pipe and installation of the new pipe through challenging geology. The new 180 ft.(54.96 m) long, 54-in. (1.37 m) . diameter sewer pipe was designed to be contained within a 72-in. (1.83 m) protective steel casing. The installation of the new sewer pipe would require a detailed understanding of the geology. The geotechnical subcontractor assembled a subsurface investigation report on November 2nd, 2017. It was quickly realized that the only way to replace the pipe was with a jacked pipe system since the large grade change and the Conrail Right of Way created no other alternative. Delaying or closing the railway was absolutely not an option as that particular railway served as the main heavy-haul route to and from Jersey City. It became apparent that a major obstacle to pipe jacking was the challenging geology present across and beneath the proposed sanitary sewer. The following challenges faced the design team prior to the installation of the replacement pipe:

Jan 1, 2019