Search Documents

By Filippo Maria Leoni, Wesley Schmutzler

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 90 inch forced sewer main relocation and to improve the soils for the base of a new drainage channel. The project is located just east of San Juan and south of the Horizon Port. The soils to be improved consisted of fill, marine clay, organics (peat) and the foundation clay layer. A preconstruction soil investigation campaign was performed to assess soil properties and to retrieve samples of the different soil layers for the laboratory Bench Scale Testing program (BST). The BST was conducted using various binder contents and water/cement ratios in each of the soil types; the selection of the different combinations and dosages was based on past extensive experiences on similar materials. Following the laboratory program, a full scale Field Test (FT) was done installing several DMM elements to verify the results of the BST and fine tune the construction parameters. Each element consisted of two 5.5 feet diameter overlapping mixing augers installed simultaneously to a depth of approximately 60 feet using a SOILMEC SR-90 dual axis drilling rig. The FT construction and post-construction coring results showed significant differences between the lab study and the actual field conditions. This paper will highlight these differences and the importance of performing both pre-construction laboratory and field tests in order to ascertain the proper mixing parameters in the different soil layers.IntroductionThe Puerto Nuevo project consists of the stabilization of a major drainage channel using Deep Mixing Method (DMM) and the relocation of a 90 inch forced main sanitary sewer outfall. The first portion of this project was a 40 x 16 x 2,000 foot box culvert installed in 2004. In order for the drainage system to be completed and function properly, the 90 inch forced main needed to be lowered about 20 feet to allow for proper drainage.DMM was chosen by the US Army corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The overall layout of the project is shown in Figure 1. The DMM is arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for ZONE A and B as an example. (Figure 2) The total amount of soils to be treated by DMM is approximately 84,000 cubic yards up to a maximum depth of 57 feet from ground surface and an Area Replacement Ratio of 100%.The equipment used to perform the DMM is a Soilmec SR90 twin-shaft jet assisted deep mixing rig (Figure 3) coupled with a LODOS 30 grout plant and two Soilmec 7T-500J high pressure pumps."

Jan 1, 2015

By M. Kumaran, A. Vetriselvan, A. Purantharan

"This paper presents a case history of evaluating the stability of a distressed earth bund and rectification measures carried out. A 5.45 km long, 7m high earth bund for drinking water storage was constructed in Andhra Pradesh. During construction of the bund following were observed – (a) a longitudinal crack at the downstream side (b) Bund on the downstream side along the crack settled to a max of 700 mm and (c) downstream rock toe level area raised by heave up to 175 mm. Investigation of the events made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. It was found that the variation in subsoil strata was not addressed during the execution.After careful evaluation, stone columns were recommended as a suitable ground improvement technique. Stone columns were used as a reinforcement to improve the shearing resistance of foundation and in turn ensure stability. By using and applying advanced geotechnical engineering analysis tools and modelling techniques, earth bund and its foundation was analysed and examined against failure by slope instability. Stone column design was carried out using in-house computer program GEOSTONECOL and stability of earth bund was analysed using TALREN software. Earth bund construction was completed after ground improvement and is performing satisfactorily.INTRODUCTIONIn order to supply water during summer season, Government of Andhra Pradesh decided to construct a 7m high and 5.45km long earth bund summer storage tank. It was one of the largest earth bund summer storage tanks in whole of South India at the time of its construction. During construction, the earth bund has undergone sudden distresses. Investigation of the series of events occurred during construction has made important contributions to the fundamental understanding of the behaviour of large earthworks of this type. This paper presents the reasons for earth bund failure, slope stability assessment of the distressed earth bund and recommendation of stone column as a suitable ground improvement remediation technique.DESCRIPTION OF STUDY SITEThe characteristics of the original construction are briefly described as follows. A shallow cut-off trench was excavated below existing ground level at the centreline of bund as shown in Fig. 1. Below the base of the trench a cut-off grout curtain was installed. Upstream and downstream shell earth filling was carried out using Clayey Sand ‘SC’ type soil. At some locations, bottom of cut-off trench has reached as deep as 12m from the existing ground level."

Jan 1, 2017

By R. T. Stain

Dynamic methods of load testing piles using a drop hammer to generate the input force have been in use for many years. These systems are based on the wave equations developed at the Case Institute of Technology, Cleveland, Ohio in the late 1960's and are well documented. Such tests are generally restricted to preformed driven piles, the driving hammer being a convenient means of generating large input forces. In 1979 the CEBTP (France) was sponsored by the FNTP (Fédération Nationale des Travaux Publics) to undertake research into existing classical methods and to develop a test that would be equally applicable to bored cast in place piles. The result of this research programme is a methodology known as SIMBAT, and which was included in a series of class A prediction trials in Belgium in 1987 (Refs 1 & 2, Paquet 1987, 1988). The purpose of this paper is: a) to examine the type of 'dynamic'/'static? load test correlations that can be obtained. b) to highlight the differences between the classical' methods and the 'SIMBAT' technique.

Jan 1, 1989

By T. Jason Hardell

The Victory Bridge project was contracted by the New Jersey Department of Transportation. The project included the construction of two 4000-ft precast segmental concrete bridges to replace the existing Victory Bridge that was built in the 1920's. The existing bridge was a swing span bridge that was in desperate need of replacement. The project was considered high priority due to the large maintenance costs to keep the swing span operating over the busy navigational channel. In March of 2003 construction began on the first bridge and by April of 2005 all of the segments were set for the second bridge. On September 5 of 2005 the second bridge was open to traffic. The total cost of the project was $110-million. The two new bridges required the construction of 24-eight foot and 32-six foot diameter-drilled shafts with rock sockets. All of the shafts were constructed in the tidal Raritan River working from barges. What will follow is a description of the construction techniques that were used to build these drilled shafts, the anticipated and unanticipated challenges that were encountered during the project, and the lessons learned.

Jan 1, 2005

By C. Vipulanandan

It is critical to monitor the ground conditions during excavation and drilling of boreholes during construction to identify possible changes in the soil and rock formations. Drilled shafts are increasingly used as foundations to support structures, bridges and other facilities in geomaterials such as soft-rocks and hard clays. Locating the bottom of the borehole during construction with the required design strength is critical. Hence developing a simple device that could be easily adapted/used with the drilling tool was of interest in this study. Determining the shear strength of the geomaterial in the borehole and at various elevations including the bottom of the borehole can lead to better quality control of construction by identifying the various layers based on strength. In this study, a down-hole penetrometer (DHP-CIGMAT) was designed, built, calibrated and tested in the field to determine its effectiveness in measuring the strength of soil/soft rock in the boreholes. Based on limited field tests, linear correlations between geomaterial strengths and DHP-CIGMAT deflection have been developed. The DHP-CIGMAT can be used to identify soils and soft rocks.

By Arpit Parikh

"Ground Water or Pore water pressure development in Sandy Soil formation is Critical situation in foundation analysis and design.Moreover it become severe while associated with higher liquefaction probability in river bank areas. It is difficult to find cost optimized solution for liquefaction mitigation under limited budget allocated for the project. Here in these research paper the attempt has been made to have clear picture of liquefaction by using various techniques and field tests. And its mitigation by suitable foundation type. In Bangladesh, On Bank of River Meghana, Power plant structures are proposed. The particular site is full of fine sand having partial silt throughout from EGL to 55 m depth. Hence in addition to Conventional Boring / Drilling operations, CPLT, SCPT, SCHT and PMT had been performed to arrive deterministic effect of liquefaction. By use of Geologismiki software and some excel based programs developed which indicates that Certainly liquefaction occurs under the event of earthquake. By Checking past records of Bangladesh we found, there are small magnitude earthquakes are inevitable and frequent. Hence fourth to overcome the bad effect of liquefaction, the deep pile foundation -Driven Pre Cast Solid Square Pile of 400 mm dia. had been suggested for various types of power plant structures. Which densify the soil and ground will improve in resisting liquefaction.1. INTRODUCTIONA Detailed Geotechnical/Foundation design Analysis had been done to arrive at optimum foundation design solution in highly probable liquefaction zone of Silty Fine Sand near Dhaka City of Bangladesh for proposed 750 MW Cyclic Power Plant. Hence about 24 no. of (Borehole) Boring and Drilling up to depth of 55 m from existing ground level has been carried out. Additionally, 09 nos. of Static Cone Penetration Test (SCPT), 02 Nos. of Dynamic Cone Penetration Test (DCPT), 02 Nos. of Pressure meter test (PMT), 02 nos. of Cyclic Plate load test (CPLT) of suitable capacity with 06 nos. of Seismic Cross Hole Test (SCHT) in boreholes had been carried out. The purpose of PMT and SCHT was to have clear idea about the Seismic behavior - knowhow of site. According to Basic principles of Soil Mechanics and foundation design, it is proved that PMT & SCHT are dynamic test. These tests stimulate field condition of occurrences of earthquake. In later stages of analysis, it is found that site have high probability of liquefaction through use of Geologismiki – Liquefaction Analysis Software. Author of these research paper also felt earthquake vibrations – strong aftershocks during site study where Epicenter of the earthquake was in Myanmar during month of august 2016."

Jan 1, 2017

By Frederick C. Rhyner

Drilled shafts have become an economical foundation choice for bridges in the northeast United States, especially when they can be constructed over water without the use of cofferdams. For the Boscawen-Canterbury Bridge over the Merrimack River in New Hampshire, an unusual design was used to avoid the use of cofferdams and avoid the need for pier caps at the waterline. This design used a pair of integral drilled shaft ? columns to form a bent type of substructure for support. Drilled shafts were 8-foot diameter, about 90 feet deep, with 16-foot long rock sockets. These are integrally constructed with 6-foot diameter reinforced concrete columns extending 37 feet from the waterline to the superstructure. Design load cases focused on lateral loads from ice flows, stream flows, wind and seismic events. Alternative analyses using different methods were made to check the design results. This paper discusses the subsurface conditions, design of the drilled shafts and columns, rebar and joint detailing issues, and construction of the drilled shafts.

Jan 1, 2004

By Shoichi Tsukuni, Akihiko Uchida, Kazuo Konishi

"In order to investigate the effect of grid-form deep mixing walls as a countermeasure for liquefaction damage to roads and private houses in Urayasu, Japan, three dynamic centrifuge model tests were conducted. Urayasu is located in the Tokyo Bay area, and private houses in the city incurred severe damage due to liquefaction during the 2011 Tohoku earthquake. In grid-form deep mixing walls design, the distance between grid-form walls is critical to prevent liquefaction. This study clarifies the relationship between the settlement of private houses and the distance between grid-form walls under the conditions that exist in Urayasu.INTRODUCTIONMany private houses in Urayasu, Japan suffered severe damages due to liquefaction during the 2011 Tohoku earthquake (Photograph 1). Fig. 1 shows the location of Urayasu and the maximum acceleration of the observed seismic waves in the Tokyo Bay area. At Urayasu, the duration of the seismic waves (hereafter called the Urayasu Wave) was about 2 min. The maximum acceleration was 1.57 m/s2 (Fig. 2), which is relatively small. The damages occurred in the land reclamation areas that consist of loose sand with an SPT-N value less than 10.To prevent liquefaction in future, it is necessary to adopt suitable countermeasures in the areas where many private houses suffered severe damages. Grid-form deep mixing walls are one such countermeasure. Fig. 3 and Photograph 2 show grid-form deep mixing walls. Walls are constructed using the deep cement mixing method. Fig. 4 shows a plane view of planned grid-form deep mixing walls for roads and existing private houses in Urayasu."

Jan 1, 2015

By Mohammad Eslami

The Tabriz-Urmiyeh Highway shortens the distance of north-western cities of Iran by about 130 km, resulting in improved access and efficient transit between Iran and Europe through Turkey. The highway crosses the Urmiyeh Lake, an inland lake surrounded by mountains. Due to the circulation of salt-water in the lake and the necessity to continue shipping between adjacent ports, a waterway should be kept open. Consequently, a bridge was built to provide access of marine traffic. A causeway bridge had a length of 1,260 m, comprising of 19 spans. In construction of the bridge, more than 400 piles having a total length of 32 km have been driven. For design of piles different methods have been used such as static analysis, dynamic testing, and correlations to in situ tests, such as cone penetration test (CPT). This paper presents construction of bridge substructure, full-scale piling tests, and methods of analysis used in the evaluation of the deep foundation capacity. The presentation includes an assessment of four current direct CPT and one CPTu methods to calculate the bearing capacity of the piles. It was found that the CPTu and dynamic testing are two suitable tools for rapid and optimum pile design and verification.

Jan 1, 2010

By Abdul Aziz Hanifah

A novel instrumentation and analysis technique, called GLOSTREXT method has recently been introduced for bored pile load tests in Malaysia. This technique provides an innovative and improved alternative for conventional bored pile instrumentation methods commonly practiced for the past few decades. Results for five case histories involving full scale static load tests for high capacity bored piles with both new and conventional instrumentation details placed in within the same instrumented piles are presented to demonstrate the advantages of this novel technique. Results show good agreement between the new and conventional instrumentation.

Jan 1, 2006

By Yazen Khasawneh, Osvaldo P. M. Vitali, John E. Agee, Mohammad Nassim

A 3D FEM modeling of a ground improvement solution for an ice rink slab with stringent differential settlement limits is presented. Due to the complexity of the geotechnical conditions and strict deformation requirements, a structural slab supported by micropiles was initially proposed. However, this solution was costly and alternative solutions using ground improvement techniques were investigated. The proposed slab is supported directly on rock at one end and on approximately 45-ft deep cohesive soils on the other end. The numerical simulations show that differential settlement would be larger than allowable, if the ice rink slab is supported directly on the existing subgrade. The addition of the ground improvement scheme with compaction grouting demonstrated that the anticipated differential settlements are reduced significantly and would become less than the allowable magnitude. This study demonstrates that the use of numerical simulations to study complex loading and geological conditions will help to optimize designs and may result on significant cost savings.

Sep 8, 2021

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees was applied to a 0.61 m (2 ft) diameter flagpole and a 0.61m (2 ft) diameter fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil was represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2012

By Robert S. Thomas, Bernard M. Tarralle, Nasser Massoudi

"The Commonwealth of Virginia is restoring and expanding its Capitol of great historic significance. Designed by Thomas Jefferson in 1785, it is the second oldest Capitol building in the United States. The building expansion required excavations immediately adjacent to its South Portico. The building, which rests on shallow brick footings, is very sensitive to any disturbance caused by construction and excavation. A comprehensive and secure plan of operations was devised by the design team to ensure that this national monument remains unharmed by the new construction. Various construction techniques were implemented to satisfy the strict movement goal of 0.25 inch and distortion of U2000. They consisted of jet grout columns to stabilize the upper soils, compensation grouting for future foundation leveling, a tied-back reinforced concrete diaphragm wall for excavation retention and foundations, and realtime instrumentation for monitoring. This paper describes the design approach for the retention system, providing information on the various construction phases and techn iques, and reports on the movements recorded by the real-time monitoring system during the course of the project. At the time of this manuscript preparation, and the deep excavation complete to final grade, the results indicate that the extremely restrictive building movement criteria have been met. The success can be credited to detailed design, close cooperation among the project team, prudent construction methods, and real-time monitoring. INTRODUCTIONThe Commonwealth of Virginia is undertaking a comprehensive renovation and expansion of the Virginia Capitol building located in Richmond, Virginia. The Capitol building was designed by Thomas Jefferson in 1785, with construction of the original building starting the same year. The Capitol building was designated a National Historic Landmark in 1960 and was listed on the National Register of Historic Places in 1966.A part of the comprehensive renovation and expansion of the Capitol is a 25,000-square foot, two-level subterranean extension on the south side of the Capitol building, which will serve as a new Visitor Center and public entrance for the Capitol. Deep excavations were required for the construction of the new Visitor Center. The excavation required a permanent retention system to accommodate an approximately 40- foot deep excavation."

Jan 1, 2005

By Nien-Yin Chang

The contemporary seismic response analysis of structures using a finite element analysis code requires six elastic spring constants to address the six degrees of freedom ground/foundation contribution to the response of a structure to earthquake shaking. However, the ground response is nothing but linear. Thus, it is critical to address the effect of the nonlinear ground response to the performance of structures under strong earthquakes. This study specifically addresses the effect of pile foundation on building vibration using finite element analyses. The effect of single pile was first investigated and the load was applied at the pile head using the single-degree-of-freedom load at a time, including three translational loads in the x, y and z directions and three moment loads about the three respective axes. In this study, the coupling effects between two or more different loads were not investigated. A load is increased monotonically to investigate the nonlinear behavior of pile under various loads. The Mohr-Coulomb model was used to represent concrete. To explore the effect of soil models on the nonlinear spring functions, the following constitutive models of soils were used: linear elastic, Mohr-Coulomb model, Cap model, modified Cam-Clay model, and Duncan-Chang hyperbolic model.

Jan 1, 2007

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity.

Jan 1, 2000

By Alan B. Wagner

The River Tower is a proposed 27-story condominium building in the heart of downtown Milwaukee, Wisconsin (USA). The tower will be over 100 m tall, and will have a ground area measuring 15 m by 40 m. The structure will be constructed of cast-in-place reinforced concrete. Certain transfer girders and stabilizing diagonals will be constructed of post-tensioned concrete. Vertical loads will be transmitted through an arrangement of columns, bearing walls, and elevator and stair cores. A mat foundation will be used to connect and integrate these load-carrying elements. The site's geologic profile includes 8.4 m of compressible estuarine (organic) deposits. To control settlement, the mat will be pile-supported. These deposits are underlain by moderate-strength inorganic deposits that extend to bedrock at 32 m.

Jan 1, 2002

By Andrew Malinak, William Perkins

Seattle’s Elliott Bay Seawall protects the 1½ miles of downtown waterfront between South Washington and Broad streets. The seawall supports the urban waterfront and infrastructure, including the Alaskan Way Viaduct and Alaskan Way, access to historic waterfront piers, and numerous essential buried utilities. Most of the original seawall was constructed between 1916 and 1936 over soft/loose non-engineered fill, estuary, and beach deposits. The majority of the original seawall was a pile-supported timber relieving platform that extended up to 60 feet behind the face of the wall (Figure 1). With maximum spacing between the timber piles of 3 to 5 feet, a virtual forest of timber piles were driven for the original wall.

Jan 1, 2018

By SungWon Park

The efficiency of the current design methods for computing pile resistances is evaluated using field load-settlement tests results. Twelve load-settlement test data for drilled shafts and bored piles were obtained from the literature. These load-test data were fitted using the ?t-z? method. Subsequently, the ultimate resistances were evaluated based upon the failure criteria from following methods: (1) the Davisson?s approach and (2) settlement corresponding to 5% or 10% shaft diameter approach. The ultimate resistances for these drilled shafts and bored piles were also predicted using methods based on the design code from North America (United States, Canada), Europe, and Asia (Japan). The pile resistances determined from field load-settlement tests were compared with those calculated using the design codes. The comparisons show that most design codes predict a conservative resistance for drilled shafts and bored piles. However, in the case of drilled shafts, we find that some of the design codes can over-predict the resistance and, therefore, should be applied cautiously. This research also shows that ?t-z? method can be successfully used to predict the ultimate resistance and the load transfer mechanism for a single pile.

Jan 1, 2009

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano, Shinya Tachibana

"The helical piling system provides solution to many geotechnical related problems due to its quick installation, higher compressive and pullout resistance, no wastage of material, workable in limited areas and reusability. However, its use as a foundation for bridges and high-rise buildings is still limited as compared to other piling methods. In the present study, the performance and load settlement behavior of screw and straight pile is investigated under cyclic compressive load in dense ground conditions. To achieve the set objectives, pile load tests were conducted in a cylindrical steel container. The model ground was compacted with dry sand at relative density of 80%. It is observed from the test results that screw and straight pile resistance reduced when the cyclic load is applied at allowable pile resistance state. The reduction in the ultimate pile capacity is more in straight pile than in screw pile. However, straight pile showed higher ultimate pile capacity than screw pile under similar pile tip diameter. The effect of helix bending deflection on load settlement behavior and ultimate pile capacity increases under cyclic loading.INTRODUCTIONScrew pile is one of the new developments in deep foundation, which is growing tremendously fast because of its quick installation technique, less noisy operation, no wastage of material and involvement of minimum manpower. Screw piles have an edge on straight pipe piles due to its high bearing capacity and uplift resistance. The installation mechanism of screw pile is different from straight pile. Torque and pressure is required to install the screw pile whereas hammering, pressure and vibration is required to install straight pile. As the installation mechanism is different between screw and straight pile, therefore, the ground disturbance that is produced during their installation is also different. The ground disturbance produced during the installation also depends upon the pile tip condition i.e. open or closed ended. Sakr, (2009) stated that the compressive capacity of screw pile in 3 to 5 times higher than driven piles having the same shaft diameter and length. The reason for this increase in pile capacity is due to helix, which is generally 2 to 2.5 times the pile shaft diameter. Larger helices can give higher end bearing capacity but it requires very powerful machinery to install in dense grounds. For instance, if large helix screw pile is installed in a dense ground then helix-bending deflection will start affecting the end bearing capacity (Yttrup and Abramsson, 2003; Malik et al. 2013 and 2015). According to Malik (2015), the equations of thin plate (Young and Budynas, 2002) with uniformly distributed load on the plate can give reasonable estimation of helix deflection due to dense ground conditions."

Jan 1, 2016

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The subsurface soil profile consists of up to 50 ft of a soft organic silty clay layer that is very vulnerable to scour, underlain by a deep deposit of hard sandy clay. Foundation construction in the Potomac River required the use of cofferdams to allow structural concrete work to be performed in the dry. This paper will the present the types of cofferdams used to construct the foundations for the WWB replacement project. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over a navigation channel in relatively deep water. Foundation construction included the installation of 48? to 72? open end steel pipe piles and cast-in-place concrete pile caps. To achieve the desired bridge appearance, pile caps were required to extend below the water surface and below the existing river bottom in shallow water locations. Conventional steel sheet pile cofferdams with tremie concrete seal were used to construct fixed span, shallow water piers. Selection of deep water bascule span foundation cofferdams was governed by several factors including contraction scour, environmental considerations and cost. Potomac River cofferdams, i.e., relatively shallow depth cofferdams that are supported by the foundation piling were selected. This cofferdam system provided a shallow profile which minimized contraction scour and the amount of filling in the river. Design issues include load selection and cofferdam stability in very soft alluvial soils. Construction issues include erection sequence, tremie concrete mix design and placement procedures.

Jan 1, 2013