Search Documents

By Chandramohan P. V

A unique tension pile where the pull is at a point a certain distance below the top of the pile. The pull is transferred by a cable consisting of high tensile strands. The HDPE duct of the cable prevents bond between the strands and pile concrete in upper portion. While soil friction on the pile will act downwards on the whole length, there is tension in the bottom portion of pile, there will be compression at the top portion.

Nov 1, 2022

By J. -M. Rescoussier

Due to Important settlements inducing major structural damages, the western part of the Grand Littoral shopping centre has been closed in 1997. The present paper describes the project of underpinning including not only micropiles under the structure of the building but also a reinforcement of the soil located between the shopping centre and the edge of the embankment surrounding the western part of the shopping centre. The aim of this reinforcement is to reduce existing horizontal movements to allowable values.

Jan 1, 2002

By Zhang Baoshan

In this paper, the forced features and dynamic behaviors of stone-column composite foundation are concisely related. The characteristics of Rayleigh wave method is summarised. This method is proposed in which, the stress ratio of the stone-column to the surrounding soil and the bear­ing capacity of the composite foundation are determined. Through the engineering cases, it is shown that, checking and evaluating the composite foundation in this method, is feasible, with high speed and low cost.

Jan 1, 1991

By E. R. Wang

This paper outlines the engineering properties of shallow soil in Shanghai area. The main points that should be paid attention to during deep foundation investigation, and general conditions of experimental soil engineering are discribed.

Jan 1, 2010

This Section describes four alternative methods for load testing of drilled shafts: high strain dynamic test (HSDT), rapid load test, static load test, and bottom load test. Until recently, static load tests were the only method available for verifying the capacity of a drilled shaft. However, because many drilled shafts carry very high design loads, the static load test was prohibitively expensive. The alternative methods, HSDT, rapid load testing, and bottom load testing are gaining acceptance because of their lower cost and faster implementation. However, these different methods do not necessarily yield the same results. This section describes the load testing methods and the differences that may occur when interpreting the test results.

Jan 1, 2004

By Ali Azizian, Brian Hall

"Driven piles were selected to support the Fraser Heights Bridge bents. Piles were a key component of the top-down construction approach, which was adopted for minimizing potential impacts on an environmentally sensitive wetland. Project requirements mandated verification of pile capacities using dynamic methods. More than 40 Pile Driving Analyzer (PDA) tests were performed. The subsurface conditions were highly variable. On the east side, piles extended through loose sands, soft silts/clays, and two peat layers and were founded in glacial till-like soils at about 45 m depth. However, on the west side, till-like materials were so shallow that it was difficult to drive the piles sufficiently deep to obtain the necessary lateral support. This paper provides an overview of the geotechnical considerations of the bridge design and top-down construction approach, and expands on the presentation of PDA results and how they compared to pile capacity estimation methods and parameters recommended in the applicable design codes.INTRODUCTIONThe Fraser Heights Bridge (FHB) was a component of the Fraser Heights Connector (FHC), a 2 km section of the South Fraser Perimeter Road (SFPR), constructed as part of the Port Mann/Highway 1 (PMH1) Improvement Project. The FHC is located in northeast Surrey BC (Fig. 1).Two major design and construction determinants were: 1) a mandated tight schedule to provide a non-tolled alternative to a new toll bridge; and, 2) an obligation that construction had to occur with minimal impact on the environmentally sensitive wetland the FHB crossed, including limiting the footprint of the permanent and temporary works to less than 45 m2, and prohibiting construction access onto the wetland. Construction equipment was only allowed on the wetland on temporary trestles or on the finished structure. This latter requirement resulted in the bridge being constructed span by span, using a top-down approach."

Jan 1, 2016

By Tony D. Canale, Anthony Mazzo

"Times Square, arguably one of the best-known destinations in the world, has undergone and continues to undergo a re-development aimed at attracting corporate tenants to the area. Mueser Rutledge Consulting Engineers (MRCE) was involved with the planning, design and construction of the foundations for the Conde Nast and 5 Times Square sites, as well as Times Square Tower. These sites are pictured in Figure 1.This paper will focus on the design and construction of the deep foundations for Times Square Tower that was developed by Boston Properties. PROJECT DESCRIPTIONTimes Square Tower is 47 stories tall, with no setbacks and an overall height to top of crown of 730 feet (222.5m). It has two basement levels extending 30 feet (9m) below grade over the full site. As shown in Figure 1, the structure occupies the entire site and has a footprint of 22,000 square feet (2,044 m2), with a total rentable area of about 1.2 million square feet (111,480 m2). The planned use for the building is office space with retail at the ground level. When completed, Times Square Tower was the final building constructed as part of the Revitalization of Times Square. Due to the site constraints, designing and constructing the foundations was akin to placing the final piece of a puzzle.Times Square Tower provided numerous design and construction challenges that were a result of tight working conditions, heavy column loads, and a compressed schedule.GEOLOGIC SETTING AND SITE HISTORYThe Times Square area is part of the Manhattan Prong called the Manhattan Ridge, a formation of old and durable metamorphosed and folded bedrock, now termed the Hartland Formation. The bedrock generally has a thin soil cover and uneven surface overlain in some areas with a thin mantle of decomposed and/or weathered rock. Overburden soils include glacial and post-glacial deposits and recent fills.Transit improvements have been made in and around the Times Square area since the early 1900’s. The 1, 2 and 3 Subway Lines that run below 7th Avenue were constructed circa 1915 using cut and cover techniques and extend about 28 feet (8.5m) below grade. The N, R, Q & W Subway Lines that run below Broadway were also constructed in 1915 using cut and cover techniques and extend about 38 feet (11.6m) below grade. The 7 Line that runs below 41st Street was constructed later, using both cut-and-cover and tunneling methods as it runs below the other subway structures at a depth of about 55 feet (16.8m) below grade."

Jan 1, 2005

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

This paper describes the general principles of the expander body with post-grouting (EBI) system, and how it is similar in nature to a large-scale pressuremeter device. The results from the installation of an EBI can be used to provide information about the stress-strain characteristics of the soil adjacent to the device and to compute estimates of nominal axial resistance. As the EBI expands during grouting, pressure is applied to the in-situ soil surrounding the device thereby compacting/densifying the soil. The nominal axial resistance for small diameter piles/ground anchors can be increased due to the greater soil stiffness and shear strength around the device, larger surface and end area, and improved soil-to-EBI interaction in side resistance. The shape of the response curves depends on the geotechnical conditions of the soil (e.g., in-situ stress state, strength, and stiffness) and the installation method of the piling/ground anchor. This technique has been used successfully with different pile types and ground anchors in a wide range of conditions from very loose sands/silts to very dense sands and medium-dense gravels as well as in soft to stiff clays. This paper also describes a mini case history in which 80 piles were installed to support an office building, and the results of the static axial compression load tests performed on a production FDP+EBI pile is also included.

By A. R. Dover

The Richmond San Rafael Bridge (Figure 1) is a 4.3 mile long major toll bridge span across northern San Francisco Bay. Tutor-Saliba/Koch/Tidewater (TSKT) conducted a comprehensive seismic retrofit, which was at the time Caltrans? largest-ever construction contract at $484 million. The robust foundation retrofit design of 11 bridge piers included the installation of 26 new, large diameter (126 to 162 inch OD, wall thickness 1.5 to 2.25 inches) CIDH and CISS piles, with steel pipe piles installed to tip elevations of Elev. ?140 to -220 ft, in water depths up to 70 feet. The open-ended steel pipe piles had initial sections ranging from 71 to 172 feet long, with full lengths that extended to the bay bottom and then through 100 to 130 feet of marine sediments to top of bedrock. The marine soils of most interest consisted mainly of soft to firm Young Bay Mud (YBM), a silty, moderately-sensitive clay common to SF Bay. A key constructability issue was the prediction of pipe piles ?running? under self weight (198 to 625 kips in air) and pile driving hammer weight (IHC S-500 with total assembly weight of 322 kips). The term "pile running" is used to describe the penetration of the pile into the soil due to the self-weight of the pile only. This issue was critical because 1) there was limited head room under the bridge deck, and 2) if piles run too deep, the pile splicing on several piles would be problematic (the lowest desirable pile top elevation after running was +10 ft). While running measurements are sometimes made during marine/nearshore construction, there is little published data on predicted vs. actual running. This paper discusses the running prediction under self weight for 26 piles, and the methodology used in developing the predictions, which ranged from 15 to 94 ft of penetration below mudline. Pile running was recorded and compared with predicted values. The prediction methodology was quite good, and no significant constructability problems were encountered. The authors ?tweaked? the model to provide a slightly improved prediction method. The paper presents the model, predictions, observations, and discusses important lessons learned.

Jan 1, 2006

By Sepideh Damavandinejad Monfared

In recognition of the practicality of using inclined micropiles as elements for foundation support to resist static and seismic loading conditions, specifically in retrofitting projects, this study presents an investigation into the beh avior of an inclined micropile subjected to simultaneous lateral load and bending moment. Three-dimensional numerical simulations are performed using the finite element method to assess the influence of micropile geometrical parameters such as angle of inclination, length, and diameter on the response of micropile-soil system. The Mohr-Coulomb failure criterion is used to define the behavior of soil and stabilized soil around micropile materials and the micropile, constructed of concrete and steel, is assumed to be elastic. The interaction between soil and micropile is taken into account by defining interaction elements covering both tangential and normal behavior. The study is carried out using nonlinear FEM analyses. The results of these simulations indicate that negative micropiles, in which slip surface deflects downward, have higher lateral load capacity than positive micropiles with slip surface deflecting upward. The conducted research also shows that increasing the diameter and the length of micropile increases the lateral load capacity. Increasing micropile diameter is more effective in increasing lateral load capacity. A relationship is developed from statistical regression analysis of the finite element modeling computations to estimate the lateral displacement of a micropile inclined at an angle of 30o in silty sands.

By Jacob A. Jordan, Rachel M. Garrett, W. Robert Thompson III, James C. Pegues

"Environmental control structures for an existing fossil-fuel power generating plant near Pascagoula, Mississippi faced several design and construction challenges due to space limitations. Conceptual design calculations indicated drilled shaft foundations would likely be needed to accommodate the higher lateral and compressive loads expected under some structures. A maximum drilled shaft diameter of 60-in was preferred due to various space constraints. Smaller diameter drilled shafts were deemed acceptable under structures with more moderate loading conditions. Furthermore, augercast piles were considered where lateral loading was not a governing design criterion.A series of SPT borings and CPT soundings revealed a subsurface profile consisting of soft to firm clays to depths of about 25 feet, underlain by fine to coarse sands. The apparent relative density of the sands was loose just below the clay, with increasing density noted with an increase in depth.Analysis of conventional drilled shafts indicated needed capacities could not be achieved unless shaft lengths exceeded 100 feet. Post-grouted drilled shafts were therefore evaluated to decrease shaft lengths by taking advantage of increased base capacity. Analyses showed the higher predicted capacities needed for some structures could be achieved with this approach. Final design for the project incorporated 90-ft long, 60-in diameter post-grouted drilled shafts; 60-ft long, 48-in diameter post-grouted drilled shafts; and 60-ft long, 48-in diameter conventional shafts. Both post-grouted and conventional trial shafts were installed as part of the detailed design phase of the project. Each trial shaft included CSL integrity testing and Osterberg-cell bi-directional load testing. Load test results revealed that additional base capacity was, in fact, achieved through the post grouting process. The 60-in diameter post-grouted production shafts and the 48-in diameter conventional production shafts have been installed at the site, with the project that would utilize the 48-in diameter post-grouted shafts deferred at this time."

Jan 1, 2015

By Emad Farouz, Francis A. Abreu

"This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule.This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.SITE AND PROJECT DESCRIPTIONThe Great Neck Water Pollution Control District (GNWPCD), located in the Town of North Hempstead in Nassau, New York, owns and operates a municipal wastewater treatment plant (WWTP) that discharges treated effluent through an outfall to Manhasset Bay, which is a tributary of the Long Island Sound. The site is located west of Manhasset Bay and is surrounded on three sides by local roads, and commercial, industrial, and recreational properties. The site has a gentle slope ranging from elevation +20 to +7 from west to east, respectively, based on the Nassau County Datum.To comply with new nitrogen discharge requirements and new design flows, the GNWPCD contracted CH2M HILL, Inc. and William F. Cosulich Associates as a Joint- Venture (JV) to design and provide services during construction of eight new advanced nitrogen removal facilities."

Jan 1, 2017

"Guideline Augered Cast-In-Place (ACIP) Pile Specification and Commentary11.0 GENERAL1.1 SCOPEThe Pile Contractor shall furnish all labor, materials, tools and equipment necessary for furnishing, installing and testing Augered Cast-in-Place (ACIP) piles as shown on the Contract Drawings and as specified herein.ACIP piles are commonly referred to by several other names. Some of them are trademarks or service marks owned by Foundation Contractors and some are names that try to describe the installation process. The term “cast-inplace” is sometimes replaced with “cast-in-situ,” especially in Europe. Some common names are Auger Cast Piles, Intruded Mortar Piles, Augerpress Piles, Augered Pressure Grouted Piles, AugerPile Foundations, Continuous Flight Auger (CFA) Piles, Grouted Bored Piles, Augered Grout-Injected Piles, Drilled or Augered Uncased Piles, and Uncased Cast-in-Place Concrete Piles. To avoid confusion, ACIP pile will be used exclusively herein.1.2 PILE CONTRACTOR QUALIFICATIONSThe ACIP piles shall be installed by an experienced Pile Contractor who upon request of the Engineer shall submit evidence of successful ACIP pile installation under similar job and subsurface conditions, including a job supervisor who shall have a minimum of five years of method specific experience.The proper installation of the ACIP piles is dependent upon the procedures used by the Pile Contractor’s field representatives and equipment provided. The Pile Contractor’s personnel responsible for the installation should have relevant experience with the auguring and pumping equipment, experience placing piles under similar site conditions (including restricted headroom if appropriate), in similar subsurface conditions, as well as experience handling the special grout mixes, admixtures, etc."

Jan 1, 2016

By Anup Kumar Mandal, Sanjoy Chowdhury, Biswajit Das

"Tailing pond of an iron ore mine necessitated raising the height of its embankment to create additional storage capacity. The tailing pond is located in eastern India and raising the height of embankment was going on during the month of January, 2014. Upstream method of construction was adopted since there was no space available at the downstream side. During the construction, about 200 m stretch of the north east embankment of height about 5.5 m failed forming a classical slip circle on the upstream side involving about half the top width of the embankment. To find out the root cause of the slope failure, detail geotechnical investigation work was carried out within the embankment as well as in the adjacent areas within the pond. About 7.5m thick very soft tailings were detected below the constructed embankment. Shear strength of the soft tailing was very low and was inadequate to sustain imposed embankment load. This resulted in the failure of the embankment. Analysis of the tailing deposit revealed that even after failure, settlement was continuing due to imposed embankment load. Under normal onedimensional consolidation, the tailing deposit would have taken about 5.7 years for 90% of primary consolidation. However, in order to mitigate the scarcity of storage space, mining plan required raising the height of the embankment within next six to eight months. Therefore, despite the fact that there was a failure, it was necessary to continue the construction on the underlying weak stratum. The system was redesigned with installation of prefabricated vertical drains (PVDs) to accelerate the consolidation process thereby gaining the in-situ strength. Strength was additionally enhanced by installing geogrids in multiple layers. It stabilized the existing embankment and also ensured construction of additional height over and above the existing embankment.INTRODUCTIONBeneficiation plant in the Iron mines enhances the mineral content by separation of contaminants and fines. The residue (waste material) is called tailings/tailings depending upon the grain sizes. These tailings in a slurry form are generally disposed in a pond called as tailing pond/tailing pond. Height of embankment of such ponds is increased either by upstream or by downstream or by centrally raising methods in different phases as quantum of deposition in the pond increases with time."

Jan 1, 2015

Jan 1, 2003

Jan 1, 2002

By Frank Haehnig, Kurt Kogler

"With a height of 200 m, a crown width of 626 m and a concrete volume of 1.6 million m³, the Kölnbrein Dam in the upper Malta valley in Carinthia / Austria is the largest concrete dam in Austria. Boasting a storage capacity of 200 million m³ with a received water load of 54 MN, this is one of the strongest arch dams in the world.During its construction from 1974 to 1977, the dam was equipped with a comprehensive monitoring system capable of comparing developing deformations and stresses with the design values.With a planned reservoir level of 1,900 m a.s.l. the dam saw the reservoir level of 1,860 m a.s.l. breached in the year 1978. This led to extremely high seepage losses of up to 200 ltr/sec and a rise in the foundation water pressure up to 100% of the dam’s height. These observations were caused by the development of horizontal cracks in the area of the middle dam blocks, between the lowest inspection walkway and the waterside.As a consequence, power plant operations had to significantly be reduced and a number of additional measures were carried out – though these did not lead to the desired sealings.The developer subsequently decided that the dam should undergo a general rehabilitation from 1998 to 1994 in accordance with a concept developed by Professor Lombardi. This concept involved erecting a 50 m high support structure with a concrete volume of 500,000 m³ on the airside of the dam, along with the addition of neoprene bearings to transfer 1.2 million tons of the horizontal load. These measures were able to reduce the deformations in the dam enough so that mostly load-bearing injections into the cracks in the dam’s concrete could successfully be carried out by way of targeted grouting measures using injection resin (RODUR) specifically developed for this purpose.In the years 1998 - 1994, a total of 130,000 m of grouting, monitoring and control drillings were executed, and around 200,000 kg of synthetic resin was injected into the cracks in the dam’s concrete.These measures have ensured the dam‘s uninterrupted operation since 1994. A number of small re- injections were again carried out on the contact surface in the years 2011 and 2012."

Jan 1, 2016

By Robert Bachus, Nikolaos Machairasm, Allen Cadden

Data Interchange for Geotechnical and Geoenvironmental Specialists (DIGGS) is a data transfer standard that is gaining widespread acceptance in the geotechnical and geoenvironmental communities. Originally developed using funding from the Federal Highway Administration (FHWA) to efficiently capture data related to geotechnical boring logs, cone penetration test (CPT) soundings, and lab testing results, the data transfer protocol is rapidly gaining traction. It has been shown to have beneficial impacts in other allied areas where disparate parties (i.e., consultants, contractors, vendors, etc.) routinely publish/submit data as part of project deliverables. The historic problem is that many of these submissions use paper copies (i.e., .pdf images) to transmit valuable data for the project… data that may extend beyond the “technical” aspects of the project (e.g., equipment operating conditions, construction production rates, project costs, etc.). These data could be used by multiple parties to assess project performance and safety, as well as to track productivity, etc. Currently, in the limited situations when actual data are compiled and transmitted, the data often are submitted as an author-specific (and often proprietary) software application and must then be re-entered into other software applications (e.g., analysis software, database, etc.) for use beyond simple data collection. An initiative undertaken by the Geo-Institute (G-I) of the American Society of Civil Engineers (ASCE) focuses on exploiting the full potential of DIGGS to geoprofessionals both within and outside of the transportation community. The deep foundations industry represents one community that could benefit significantly from using DIGGS. Data of interest to DFI members include production records, quality assurance information (e.g., verticality and alignment, concrete strength), and, importantly, load test results. When adopting DIGGS, users need not modify how they capture data, but rather will use DIGGS as a vehicle to transfer data to other applications in a standard format where it can be shared, used, stored, and retrieved. This paper and associated presentation will describe DIGGS and demonstrate how DIGGS can be used effectively within the deep foundations community.

Jan 1, 2019

By Renzo D. Verastegui, T. C. Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high rise towers in New York City. The 52-story condominium building is located on a 60 by 100 feet lot on East 60th Street between Park and Madison Avenues. The geographically complex site is bounded by two fragile 5-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City subway tunnel on the south. To add to this complexity, the ambitious development required 70 to 80 feet of excavation, mostly below groundwater level in highly permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 feet over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This paper describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.INTRODUCTIONThe project site is located at 45 East 60th Street, on the block bounded by East 61st Street to the north, East 60th Street to the south, Park Avenue to the east, and Madison Avenue to the west. As shown in Fig. 1, the site is surrounded on three sides by buildings sensitive to differential settlement. In addition, a NYCT underground subway structure lies below East 60th Street approximately 13 feet south of the site. The base of the subway structure is approximately 42 feet below the street.The project consisted of constructing a 52-story tall building. A portion of the superstructure cantilevers 24 feet over an adjacent five-story historic building. The underground construction for the new building involved a four-level basement, extending about 60 feet below ground surface. The excavation subgrade is much deeper than both the subway structure and the adjacent shallowly-founded building foundations."

Jan 1, 2016