Search Documents

By D. T. Bergado

The uppermost subsoil profiles of the Bangkok plain can be divided into four layers, namely: weathered clay, soft clay, stiff clay, and dense sand layers. The soft Bangkok clay is a normally consolidated marine clay with built-up preconsolidation effects and overlain by a weathered crust. Up to the present, a large number of full-scale tests on excavations and pile foundations has been made by numerous investigators. Based on these results, the available data are reviewed and evaluated. The results show that for test excavations, the excess pore pressures were overpredicted by the existing theories. The vertical and lateral movements in the excavations can be predicted by the bilinear and non-linear finite elements using appropriate modulus values. Relationships among probability of failure, safety factor, and safety margin of the excavation were also obtained. In the case of pile foundations, good agreement between the measured and predicted ultimate pile capacities were obtained for long piles. The adhesion factors ranged from 0.4 to 1.0 while the average skin friction factor was found to be 0.33. The ultimate capacity of the pile was also predicted successfully by using the Dutch cone data. For lateral deflection of piles, Davisson and Gill's theory predicted well in the low deflection zone while Poulos' theory agreed well in the high deflection zone. From the probabilistic analysis of ultimate pile capacity, the probability of failure was related to the central factor of safety. The piles usually used in Bangkok area are mainly precast concrete piles

Jan 1, 2010

By H. W. Hunt

Accessories are increasingly used to protect and extend H, pipe, precast concrete, timber, and sheet piles for any soils conditions. With point protection, piles can be driven through boulders, layered rock, garbage dumps, and waterfront debris to provide dependable support for all types of structures. Splicers for pipe piles can be tapered for a water-tight drive-fit that does not require welding. The pipe splicer can be made applicable to precast concrete piles. Splicers for H make the long pile as strong as an unspliced length with only simple welding. Transition splicers quickly connect different types or sizes into efficient composite piles.

Jan 1, 2010

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By Peter Faust

The foundations for the new South Viaduct Bridge in San Francisco were extremely challenging due to the requirement for very large and deep piles installed adjacent to historic structures. Drilled shafts up to 12? foot in diameter were constructed to a maximum depth of 200? feet in alluvial soils and Franciscan Bedrock using an oscillator system for the installation of the permanent steel casing. This paper provides an overview of the construction techniques, the equipment, and the challenges associated with constructing 12? foot diameter shafts on this very complex project in one of the nation?s nicest landscape setting.

Jan 1, 2011

By Robert L. Parsons

This paper describes the results of a detailed analysis of a loess deposit at the deep foundations test site established by the Kansas Department of Transportation. Multiple CPT, SPT, and pressuremeter tests were conducted as part of the investigation. This paper includes an evaluation of the effectiveness of common correlations used with the CPT, SPT when used for classification of loess and estimating its properties. Results show that common correlations must be used with caution as significant errors in estimation may result from using methods developed for other soil types. Laboratory testing included direct shear, triaxial, collapse, and consolidation testing, with many of the tests conducted on both vertically and horizontally oriented samples to evaluate anisotropic behavior. The results showed that strength properties could be considered to be isotropic.

Jan 1, 2009

By M. Zanotto

[ ] A period of heavy rains caused the river Adda to flood parts of the Valtellina, one of the Alpine valleys of Northern Italy. The exceptionally high waters put under considerable strain the whole system of embankments and levees controlling the river and protecting the adjacent towns and lands. In some places the water breached and washed away the embankments, submerging large tracts of cultivated land, buildings, roads and railway tracks. The town of Talamona, in the lower Valtellina, was hit particularly hard: in its proximity the river overrun and then washed away 300 m (1,000 ft) of embankment (see vicinity map, fig. 2), depositing large amounts of riverbed debris onto over 400 hectares (1,000 acres) of fertile land.

Jan 1, 1992

4.5.1 General The provisions of the article shall apply to the design of axially and laterally loaded driven piles in soil or extending through soil to rock. 4.5.1.1 APPLICATION (Revised Article 4.3.1.1) Piling may be considered when footings cannot be founded on rock, or on granular or stiff cohesive soils within a reasonable depth. At loca-tions where soil conditions would normally permit the use of spread footings but the potential for scour exists, piles may be used as a protection against scour. Piles may also be used where an unacceptable amount of settlement of spread footings may occur. 4.5.1.2 MATERIALS Piles may be structural steel sections, steel pipe, precast concrete, cast-in-place concrete, prestressed concrete, timber, or a combination of materials. In every case, materials shall be supplied in accordance with the provisions of this Article.

Jan 1, 1989

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees is applied to a 0.61 m flagpole and a 0.61m fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil is represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2011

By Chris Sammon

The Block 75 portion of the City Creek redevelopment project in Salt Lake City required multiple shoring walls surrounding the 6 acre site constructed to depths ranging from sixty-five to ninety feet below original street grade. Shoring for the project was challenging due to site soils consisting of cobbles, sands and gravels, interlayered lakebed silty clay and fine sandy silt with incised stream deposits of silty/clayey sand and gravels combined with a high groundwater table. Moreover, several abutting structures each with a unique foundation system would be directly or indirectly supported by the shoring system. Three sections of interest are the shoring walls constructed at Main Street, Deseret Trust Building and Eagle Gate Tower. Main Street shoring extended to as much as sixty-five feet below street grade and utilized existing basement walls anchored in place in the upper zones with soil nail walls with pre-installed vertical elements for face stabilization below. Data are presented which illustrates the effect dewatering had on the settlement of the Main Street Shoring. The Deseret Trust Tower shoring supported a 12 story, historical masonry building. Site conditions dictated a separate design for the east side and the north side of the building allowing comparison of relative performance between these walls. Settlements of this structure were controlled by installing micropiles through the 90 year old structures spread footings. Shoring for the Eagle Gate Tower was to be constructed immediately adjacent to a mat supported 22 story high rise structure. This shoring system combined secant piles, ground anchors and incorporated existing abandoned-in-place pipe piles with infilling high pressure jet grouting to create a cutoff wall and eliminate the adverse impacts of dewatering below this sensitive foundation.

Jan 1, 2010

By Brian P. Waagner

Construction law in general and the law of deep foundations in particular continues to develop rapidly, particularly in the areas of risk allocation. Public and private owners are increasingly using contractual disclaimers to shift the risk of differing site conditions to contractors, and courts are increasingly willing to enforce these contractual devices. Perhaps also in an effort to control costs, public and private owners are turning to design-build contracting techniques. While design-build offers many advantages over traditional project delivery systems, it does not answer all of the risk-allocation questions that frequently arise. Even in design-build, problems with unanticipated subsurface conditions and defective design are not easily addressed. Finally, developments in electronic commerce present the potential to transform the construction industry.

Jan 1, 2002

By Brent Wilkins

The project team was tasked with the design and installation of a deep foundation system to support an expansion to a power generating station in Glenrock WY. Cast-in-place piles installed by a fixed mast drilling platform were assessed to be the most efficient foundation system for the subgrade conditions and range of design loads for the project. It was determined that conventional augered, cast-in-place piles could not be installed to the required pile toe elevations. Subsurface materials consisted of interbedded coarse- and fine-grained soils to about 23 ft to 30 ft depth below the ground surface, underlain by carbonaceous shale (claystone) with interbedded sandstone. The overburden materials varied from very soft to medium stiff and loose to dense. The claystone was typically foliated and very weak to weak whereas the sandstone was typically massive and very weak to weak. The site characterization consisted of a variety of field and laboratory programs including soil borings with Standard Penetration Tests, pressure-meter testing, and geophysical testing. A load test program was performed involving the compressive, lateral, and tensile testing of piles ranging from 14-in to 24-in diameter. Compression test piles were instrumented with vibrating wire strain gages. The paper includes a discussion of the regional and local geologic and geotechnical parameters, particularly the results of the various in situ and laboratory test programs. The selected foundation system is introduced. Load test results are then presented along with analysis and discussion of these results with regard to performance of the piles in the claystone.

Jan 1, 2009

By Sitotaw Y. Fantaye

"The first segment of the Second Avenue Subway extension is approaching construction completion. The new extension will operate along Second Avenue from 96th Street to 63rd Street, where it will divert west along the existing 63rd Street line, stopping at the Lexington Avenue/63rd Street Station. The new line will have stateof-the-art stations at 96th, 86th, 72nd and 63rd streets.Most of the two-track, twin-tunnel subway was constructed using bored tunnel methods (Figure 1), with a tunnel boring machine (TBM). The launch and retrieving box of the TBM was strategically located at the south end of the 96th Street Station where bedrock exists approximately 70 ft (21.3 m) below street level. The TBM launch box and the 96th Street Station (Figure 2), including the ancillary facilities adjacent to the station, were constructed by the cut-and-cover method. The cut-and-cover work required the contractor to design and implement a stiff, tightlybraced retaining wall, approximately 100 ft (30.5 m) long, to tie the existing tunnel constructed in the 1970s to the new station, temporary street decking over the entire excavation, and a wide range of excavation support systems at various locations.The cut-and-cover construction posed significant challenges including: installation of street decking on busy Second Avenue, relocation and suspension of the myriad utilities beneath the streets, and configuration of a lateral support system that would minimize movement of adjacent structures but not slow down excavation activities. This article describes the innovative solutions developed to manage and facilitate safe and efficient construction without disrupting Second Avenue, a major southbound one-way thoroughfare.The work was performed in several phases involving: (1) preconstruction condition survey of existing buildings, (2) installation of instrumentation and monitoring, (3) major utility relocation efforts to move vital utilities from within the alignment of the slurry wall on both the east and west sides of the avenue, (4) implementation of maintenance and protection of traffic plans, (5) installation of temporary street decking across the entire avenue and over the excavation to allow an orderly movement of traffic and pedestrians, (6) staged excavation and installation of an intricate temporary bracing system beneath the decking (7) step-by-step construction of the new subway station’s structure and (8) staged removal of the bracing as the structure gained sufficient strength to resist the lateral loads. The main focus in this article is the design and construction of the temporary street decking and lateral bracing systems; the utility suspension system and the north tie-in that allowed the daunting task of excavation and construction of a new subway station in bustling New York City, with minimal disruption to the community, businesses and everyday traffic."

Jan 1, 2016

By Bengt H. Fellenius

The bearing capacity equation?"the triple N formula"? is now about 50 years old. It was developed from theory of plastic resistance of metal to a cone being pressed into the surface of the metal, superpositioned by resistance due to shear in an interparticulate medium (soil; note, we are not dealing with metallurgy), and tempered by work necessary to move the footing into the medium. The equation (and its coefficients) was "confirmed" by tests on small footings placed at or near the surface of the soil. The equation is a basic tenet of every geotechnical textbook, manual, and code. Over the years, innumerable variations of the N-coefficients and adjustments to the equation have been published. The main assumption behind the bearing capacity equation is that a shear plane develops between two essentially otherwise unaffected bodies: the main soil body and a body comprised of the footing with some soil. Moreover, the notion is that a model footing placed at or near the surface of a soil would behave proportionally or similarly to a full-scale footing, or to even a same size footing (pile toe) placed at some depth in the ground. This is not in agreement with factual observations. It is suggested that the behavior of a small or large diameter footing as well as a pile toe is governed by compression of the soil below the footing or pile toe and not by "bearing capacity".

Jan 1, 1999

By Joe Harris

Large structures, such as a multistory office building or a large storage tank, are constructed the most economical way possible, which may involve a shallow foundation system placed on native soil or compacted fill material. Over the life of the structure, the foundation system may not perform as originally anticipated, leading to differential settlement. Minor differ- ential settlement is expected; however, settlement that exceeds allotted tolerance can render the structure inoperable. Compaction grouting is a well-known and accepted ground improvement technique that can be used to not only stabilize but relevel multistory buildings and large dia- meter storage tanks. Two projects, each with differing types of structures, were successfully remediated utilizing com- paction grouting as the primary method to remedy settlement.

Sep 1, 2023

By Yu Zhenquan

At the construction site of Bao Shan Iron &. Steel Mill in Shanghai, lots of RC driven piles with length of 50 to 60m were applied. The most unfavourable distribution of stress along the pile shaft was known by measuring the compressive and tensive stresses. With analysing the test results a phenomenon of impact fatigue of RC pile was discovered, the range of impact fatigue and its critical zone can be distinguished. Finally some countermeasures are presented to avoid the impact fatigue of RC long pile.

Jan 1, 1991

By Reinhard Gnilsen

Soil Nail walls, like any other structure, must meet high standards of design to be acceptable to the public and owners. On the other hand, the concept of soil nailing trails behind other structures in terms of defined design criteria that are commonly acknowledged. This is not to say that soil nail walls need to be less safe or less conservative than alternative more conventional concepts. Instead, the lack of established design criteria and design methodology entails that rules of thumb from past experience, overly simplified calculation assumptions, and the engineers' common sense judgement must substitute for a complex analysis of true stability and wall performance. Those "design approaches" must be conservative to ensure an adequate structure. Also, soil nailing may not be perceived prudent where site conditions are considered beyond past experience. For instance, site conditions may be perceived out-side the scope of soil nailing applicability where walls are very high, soil parameters variable or low, or nearby buildings close to the wall edge. The latter relates in particular to deep

Jan 1, 1988

By Robert Bittner

The following is a report on the development of two unique and separate cofferdam systems used in the construction of the marine foundations for the I-205 Columbia River Bridge at Portland, Oregon for the Oregon Department of Transportation. The first of these two systems utilized interlocking H-pile 100 ft long to form a cofferdam 145 ft by 58 ft in plan and 100 ft deep. The second system consisted of two immense bell shaped steel forms. The larger of the two forms was 83 ft by 66 ft in plan, 62 ft high and weighed 450 tons. This form was externally stiffened for a designed hydrostatic head of 54 ft. Both forms were designed, except for the top 14 ft, to be set and stripped in one solidly welded unit. The supporting geological formation for the bridge foundations is the Troutdale, a cemented sand and gravel. This formation is at the ground surface on the Washington Shore and slopes downward to a depth of 115 ft below normal high water at about mid-channel. In this area the Troutdale formation is covered with a layer of fine to medium sand 90 to 100 ft thick. It was the variable depth of the Troutdale which determined the two types of foundations and the corresponding to the two cofferdam systems.

Jan 1, 2013

By Eric M. Klein

As part of the Woodrow Wilson Replacement Bridge project several damaged wetland and environmental areas were to be mitigated. One of the mitigation projects consisted of constructing a Denil fish ladder around Peirce Mill Dam in Rock Creek National Park, Washington, D.C. The dam is a historic structure operated by the National Park Service. The fish ladder is located between the east abutment of the dam and Beach Drive, a major collector road. Construction of the fish ladder required removal of a portion of the east abutment and an excavation that extended about 22-ft below the pavement of Beach Ave. It was not possible to close Beach Drive except for very brief intervals or at night; therefore, a support of excavation system that would minimize disruption to the public was required. The high groundwater required that the groundwater be cut off prior to excavation; the random rubble and soil fill, and shallow but erratic rock surface precluded driving sheet piling. A jet grout system was selected because the grout probe could penetrate the rubble fill, stabilize a variety of soil conditions, and cut off the ground water prior to excavation. It was not possible to construct a stable wall without tiebacks or soil nails. Given the schedule and tight working conditions it was decided that soil nails through the jet grout wall facing would be the most cost effective method, as it did not reduce the working space as rakers would and would be more cost effective than prestressed tiebacks.

Jan 1, 2006

By Narong Thasnanipan

Performance of diameter 1.5 m toe-grouted bored pile founded at depth 44 m in sand-gravel formation of Chiang Mai City is presented in this paper. Toe grouting was applied by using tube-a-manchette method. Effectiveness of toe grouting was observed from the standard penetration tests conducted immediately below pile toe through grouting pipes at two stages, prior to grouting and three weeks after completion of grouting. Improvement of pile end resistance by toe-grouting is demonstrated with a series of back analyses carried out by load-transfer method employing hyperbolic transfer function. Construction experience of large diameter deep-seated bored piles in multi-layered subsoil and practical aspects of toe-grouting are also briefly discussed.

Jan 1, 2002

By Kyle A. Kershaw

The City of Grand Forks, North Dakota obtains drinking water from both the Red River and Red Lake River through a system of raw water intakes, shallow pipelines, and pump stations. However, during flood events, the City often loses access to the system, as evidenced during the record flood event in 1997. As a result, the City decided to construct a new gravity raw water intake system, including a pump station at the base of a 65-foot-deep, 60-foot-diameter caisson, behind a new levee system. Because of high design flood elevations and connectivity of river head to underlying soils, uplift resistance was required for the caisson. A total of 37, 2-foot-diameter, augered cast-in-place (ACIP) piles were chosen to provide uplift resistance. Because of the difficulties associated with installation of piles within the confined space of the constructed caisson and basal stability concerns, installation was completed from the existing ground surface to a depth of 120 feet. Several design and construction issues arose, including squeezing ground during pile installation, placement of long reinforcing bars, and installation of a dual material pile. A dual material pile was required to ensure that the ACIP pile below the base of the caisson was structurally sound and the pile above the base of the caisson could be easily excavated during sinking of the caisson. This paper discusses the solutions to each of these issues, as well as construction sequencing, load testing and integrity testing of the ACIP piles, and the successful completion of the project.

Jan 1, 2003