Search Documents

By Liu Run, Jia Zhao-lin, Yan Shu-wang

"Piles with diameter larger than 2m in engineering can be defined as large diameter pile, and piles used for oil platform foundation in Bohai Gulf, are usually over 100m long and 2m in diameter. Such long piles have to be manufactured by segments before installation, because of transformation and hoisting difficulties. The segments of the pile are assembled by welding during installation one to another. Normally, assembling two pile segments takes one day or even a longer time, which mainly depends on construction conditions. After pile segment assembling, it proves to be difficult to restart the successive penetration. The mechanism of pile refusal is discussed and the process of driving a segmented pile is simulated with a finite element program. The calculating results show that, when the stick-up stability was satisfied, increasing the length of the last segment of the pile and assembling the pile segments when the pile tip penetrates into a clay layer could greatly ease the difficulty of driving the pile. Furthermore, cutting down the pile extension time is also one of the most effective measures to minimize the refusal risk.1. InstructionIn recent years, more and more oil platforms with six or eight legs have been adopted in Bohai Gulf, China. The leg piles with diameters of 2m or more have to be driven to about 100m below the sea bed. Such long piles have to be manufactured by segments before installation, because of transportation and hoisting difficulties. The segments of the pile will be assembled during installation, in which a successive segment will be attached to a formerly penetrated one by welding (Fig.1). The assembling work often takes one day or even a longer time."

Jan 1, 2014

By Frank Haehnig

Ground freezing is a technique which is used more and more in tunnelling under complex ground conditions. This paper will present three case studies which highlight different aspects of the ground freezing technique when applied in urban environment. The first project is the City-Tunnel in Leipzig, Germany, which is being built beneath the central station and which is the largest ground freezing project currently under construction in Germany. The second case study is part of the North-South-Line project in Amsterdam, Netherlands where ground freezing will be carried out to al-low the TBM drive through old wooden foundation piles. The freeze tubes for this project will be driven using Horizontal Directional Drilling (HDD). The last project is the Hallandsas Tunnel Sweden where the ground freezing equipment has to be installed against high water pressure. The paper illustrates that ground freezing can be implemented in difficult ground conditions such as soft ground, highly fractured rock and high water pressure. The case studies highlight the importance of good workmanship. With the increasing numbers of large tunnels being constructed in difficult ground conditions the paper concludes that the complex case studies presented will be-come more representative for future tunnel projects in urban environments.

Jan 1, 2008

By Frank Rausche

Introduction and Background Testing -Pile Preparation -Data Processing -Data Interpretation/Case Studies Case Studies - Existing Piles Stories from around the world

Jan 1, 2001

By Philip J. H. Ball

The new application and development of grout jacking processes has combined, over the last decade in particular, to provide a method by which the effects of new underground construction on superficial structures can be controlled to acceptable levels. This paper sets out the basic principles, processes and limitations of compensation grouting. It describes key elements of the philosophy and design and details the control systems required to perform satisfactorily. To illustrate the application, a case history is described for the construction of a shaft and tunnel within and beneath the prestigious structure of Harrods in London.

Jan 1, 2000

By D. Michael Holloway

The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the structures along the realignment of Interstate 880. The project replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers well beyond local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata and quantifying the effects of installation on the long-term capacities of the piles led Caltrans to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1995

By Mait Mets

In Estonia, the deformations monitoring of 1500 buildings are currently under investigation, buildings on pile foundations make up 10 per cent of these. In the following text we will be considering the behaviour of pile foundation buildings in various parts of Estonia, in differing geotechnical conditions.

Jan 1, 2002

By Jeff Jackson, Paul Axtell, David Graham

The Montana Department of Transportation recently awarded a contract to construct a replacement bridge across the Clark Fork River in Heron, MT. Both abutments and both intermediate bridge bents were to be founded on 6-ft and 8-ft diameter, permanently cased drilled shafts with rock sockets, respectively. Two drilled shafts per substructure location were designed for a total of eight drilled shafts. The original design included 6-ft diameter drilled shafts at the abutments but the Contractor elected to submit a Value Engineering proposal that increased them to 8-ft diameter. On the basis of the subsurface exploration program, extremely challenging subsurface conditions were known to exist, including the potential presence of large boulders within the predominantly sand and gravel soil matrix. The successful bidder elected to use an oscillator to install the permanent casing to the top of bedrock, while simultaneously removing the spoils from inside the casing with a clam-grab. On seven of the eight shafts, this approach worked well. Unfortunately, on one of the shafts, the casing met refusal on one or more boulders encountered in the predominantly sand and gravel soil overburden. Following several attempts, and despite several variations of approaches, it was determined that the casing could not be advanced beyond the obstruction without unacceptable risks to the pile-supported temporary work trestle (i.e., loss of soil and reduction in pile capacity for the foundations supporting the work trestle). To mitigate the problematic drilled shaft, a unique solution was designed and successfully constructed. The solution involved the construction of seven 16-in diameter micropiles constructed within the confines of the obstructed casing. The micropiles were drilled to bedrock through the sand, gravel, and boulders and include rock sockets to satisfy axial design requirements. The micropile casing thickness, grade and grout strength were designed to provide adequate flexural strength as well as to satisfy other design requirements. Upon completion of the micropile installation, the upper portion of the drilled shaft above the boulders and within the permanent casing was constructed as usual. This paper discusses the difficult subsurface conditions at the site, the drilled shaft construction difficulties, and the design and construction of the micropile solution.

Jan 1, 2018

By Sheryl D. Gallagher

The project consisted of filling an abandoned underground limestone mine to facilitate construction of a new entrance ramp to I-470 in Lee?s Summit, Missouri. Due to collapse of mined areas near the project site, design included determination of the limits of remediation for the project and minimum construction requirements for mine infilling. The Judy Company, contractor selected for the mine infilling, experimented in the laboratory with several grout mixes to determine the appropriate mix for the project. Infilling was accomplished from the ground surface, and camera observation was used to monitor the barrier wall construction and infilling process. It was discovered that some of the mapped rooms were larger and some were smaller than indicated on the construction plan.

Jan 1, 2009

By T. Iwanowski

Stress wave measurements and calculations are often used to make a safe determination of the bearing capacity and the integrity of driven piles. Some applications to the restoration of old buildings in the Old Town of Stockholm are referred to and especially analyses of measurements combined with simulations are discussed here.

Jan 1, 1991

By Feng Yongxuan

Anchored sheep pile is normally used in deep excavations, many of which only require stability in accordance with Terzaghi theory. In this paper, based on the experience, new lateral earth pressure method is adopted taking account into interaction among soil, anchors and sheet piles so that a group for the project under very difficult conditions and very severe requirments, especially, for the displacements are determined according to that mentioned above. During and after construction, displacements monitoring were carried out for about four months, which was proved that there was a little difference between calculation and practice.

Jan 1, 1991

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By Julie Hampden, Tim Dardis, Per Reinhall

"Noise from impact pile driving can harm fish, marine mammals and other sensitive wildlife over large areas. Marine pile driving is highly regulated, and regulators require sound levels to be below certain thresholds to avoid harassment and injury to sensitive marine life. In many locations, timing restrictions, use of noise attenuation technologies and extensive monitoring for impacts to wildlife are also required. As a result, permitting can be laborious and time consuming, and project implementation and scheduling can be complicated. Underwater noise levels are measured with an underwater microphone (hydrophone), which converts noise pressure to voltage and is calibrated to express the noise pressure in Pascals (Pa). The pressure is often expressed using a logarithmic scale, in decibels (dB). Several specific metrics can be used to describe underwater noise. Three common metrics are the instantaneous peak sound pressure level (dBpeak), the root mean square pressure level (dBRMS) and the sound exposure level (dBSEL) referred to as the peak, RMS and SEL levels, respectively.During impact pile driving, the peak pressure represents the instantaneous maximum pressure, either overpressure or underpressure, observed during each pile strike. The RMS level is the square root of the mean of the square of the pressure during the duration of the impulse; it is the average pressure level of the pile strike from beginning to end. The cumulative SEL (SELcum) is calculated by summing the cumulative pressure squared and integrating over time of duration of the pile strike. SEL is used as an indication of the cumulative energy of a pile driving event, which may consist of one or many pile strikes.Regulatory agencies use these metrics to help characterize the noise pressure levels that can affect sensitive species. Some of the most frequently encountered biological thresholds in the Northwestern United States that are used by regulators to describe potential impacts to sensitive species are summarized in the following table. Agencies have defined thresholds for different types of injury, either hearing or bodily harm, and for temporary injury or disturbance."

Jan 1, 2017

By Frank Callanan

The Ameristar Casino expansion project included the design and construction of a 25-story hotel and 9-story parking structure expansion. The site is located in a floodplain on the banks of the Missouri River in Saint Charles, Missouri, where the underlying soils are potentially liquefiable. The geotechnical engineer performed subsurface exploration and analysis, which included site-specific seismic response and liquefaction, and provided geotechnical design recommendations. In the event of an earthquake, post-liquefaction settlement was calculated to be approximately 14 inches. Additional project constraints included wetlands protection, construction adjacent to the existing facility, flood protection and river bank stability. Because of the liquefaction issue, the geotechnical engineer consulted with a specialty geotechnical contractor on ground improvement methods. This consultation led to a proposal to eliminate deep foundations from the design and support the structures on shallow and mat foundations. The geotechnical engineer assisted the design team with foundation design analysis and value engineering assessments. Together with the project team, the geotechnical engineer used the data to evaluate foundation options and construction methods to overcome the site challenges and concluded that ground improvement was the optimum course of action. Because of the nature of the site constraints, a number of ground improvement methods were needed. The geotechnical engineer evaluated the methods proposed by the geotechnical contractor and provided the technical specifications for the ground improvement bid package, which included vibro-compaction, compaction grouting and micropiles. The ground improvement allowed for the use of shallow foundations (mat and spread footings), which provided the client with significant time and cost savings over the deep foundation alternatives.

Jan 1, 2009

By Gordon King

The City of Atlanta Water Department required the construction of a two sludge tanks and a wet well at the existing Chattahoochee Water Treatment Plant. Western Summit won a design build contract to build the project and proceeded to evaluate the wet well size options, and construction procedures. The final design required the construction of a 1 million gallon tank. The proximity of the underground tank to adjacent roads and existing plant structures ruled out laying back the excavation. As a result a tied back sheet pile retaining wall was initially proposed.

Jan 1, 2003

By R. A. Bullivant

Roger Bullivant Piling Limited has started 1992 with the introduction of the CONE PILE into its range of precast concrete foundation techniques. Since the establishment of its Piling Division ten years ago, alongside the original Underpinning Company, a commitment to innovated development has seen a steady growth in Roger Bullivant's activity in piling, ground treatment and general foundation engineering. Over the last four years, £1.2 million has been invested by the Bullivant Piling Division into research and development in the field of precast piling and other foundation systems. The goal has been to develop economically attractive systems tailored to our clients design requirements and, wherever possible, unique to Roger Bullivant Piling.

Jan 1, 1992

By N. S. Yet

This paper shall present the design and construction of bored pile and diaphragm wall for the proposed MHA complex in Singapore. The work was carried out by L&M Foundation Specialist Pte Ltd and PWD Consultants Pte Ltd was the consultant for this project. A brief description of the project is first presented to illustrate the scope and scale of the work involved, which includes the construction of bored piles and diaphragm walls and installation of steel stanchions in the bored piles. This is followed by a description of the methodology used to analyse and design the wall and bored piles. As both towers in this project are supported on bored piled foundation and are constructed by top down construction method, the analysis of the wall has taken into consideration the sequence of work phase by phase and this was carried out by means of a commercial finite element program called CRISP. Modelling of the problem will be briefly described and the findings from the numerical analysis will be presented. This is followed by a description of the structural and geotechnical design aspects of bored piles. The paper shall then describe the difficulties encountered for this project and solution used to solve the problem. The subsoil condition will be described with special mention on the encounter of very strong granitic rock at depth above the maximum excavation level of the basement at certain locations, hence necessitating the drilling of rock for a considerable depth for both bored piles and diaphragm wall. At this juncture, the construction method used to drill through the rock will be briefly described. For construction of bored piles, penetration of rock was carried out by chiselling or drilling using reverse circulation rigs. For construction of diaphragm wall, it requires the employment of Bauer hard rock cutter which uses cutting wheels fitted with roller bits and are capable of excavating into granitic rock of compressive strengths more than 100 MPa.

Jan 1, 2000

By E. R. Wang

This paper outlines the engineering properties of shallow soil in Shanghai area. The main points that should be paid attention to during deep foundation investigation, and general conditions of experimental soil engineering are discribed.

Jan 1, 2010

By K. Rainer Massarsch

The effects of soil displacement caused by pile driving on adjacent piles and structures are discussed. A method is proposed to estimate the point of force equilibrium which makes it possible to calculate up-lift forces and pile head movements. For the case of pre-coring a method is proposed to estimate the stability of the bore hole, based on cavity expansion theory. Model tests were performed to establish the displacement pattern of the soil during the driving of a pile group. It can be concluded that at the ground surface, already installed piles have little influence on the lateral displacements, but reduce significantly the soil heave. During the driving of a pile group, the soil is displaced according to a complicated pattern, which is strongly influenced by the order in which the piles are driven. In clay the displaced soil volume corresponds to the total volume of driven piles.

Jan 1, 1989

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

By Mark R. Svinkin

Construction-induced vibrations may be detrimental to adjacent structures and sensitive electronics operating nearby. Construction vibration sources have a wide range of energy and velocity, as a function of time, transmitted on the ground. Analysis of existing methods for predicting ground and structure vibrations shows that empirical equations provide calculations only of amplitudes of vertical soil vibrations with insufficient accuracy. This paper presents the application of the impulse response function concept to solve the geotechnical problem of predicting ground and structure vibrations before installation of vibration sources. Impulse response functions reflect real behavior of soil and structures without the investigation of soil and structure properties. A procedure is presented to compute predicted ground and structure vibrations. Good agreement is found between predicted and measured records.

Jan 1, 1999