Search Documents

By Takeshi Maki, Kh. Adeel Tariq

"The lateral resistance of the structure plays an important role during seismic event and it can be increased by using ground improvement. In this study an attempt has been made to investigate the effect of cement-treated sand on the lateral capacity of the pile. The behavior of piles surrounded by sand only and cement-treated sand confined in a steel box (30 x 30 x 50 cm) which is subjected to lateral cyclic load has been investigated. Piles having a diameter of 2.5 cm and embedded to a depth of 45 cm were used. Steel and aluminum piles were used to investigate the effect of flexural stiffness on the lateral capacity of the pile. Bottom supports of piles were also changed from pinned to fix. Well graded sand compacted to 70% of relative density (RD) was used. Cement-treated sand having a compressive strength of 3.7 MPa was used. Displacement controled lateral load tests were performed and cyclic loads were applied until pile displacement was 4%, 10%, 20%, 35%, 50%, 75% and 100% of pile diameter. Results evaluated are compared with common method of analysis like Brinch hansen (1961), Brom (1964), Poluos (1980) etc. Results have indicated that the stiffness of a pile affects its lateral capacity. The introduction of central cement-treated sand part increased 5 times the lateral capacity of piles as compared with a sand only condition.IntroductionPiles are used extensively around the world to support loads of structures. Piles are commonly used to carry axial load, but in some structures, the lateral capacity of the pile is more important than the axial capacity: for example piles supporting earth retaining structures, electric tower foundation, etc. Structures can be subjected to both axial and lateral forces, like structures constructed at harbor that are subjected to lateral force due to waves action; and structures built in earthquake prone areas like Japan."

Jan 1, 2017

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By Walid El Kamash, Sadik Oztoprak

"Soft soil presents a challenge against multistory buildings in some cities of Egypt such as Port Said due to the consolidation settlement. Deep mixed (DM) columns are used to improve the soft foundation soil in order to reduce the total and differential settlements. Latest research revealed that this improvement technique also increases the rate of mechanical consolidation due to column yielding caused by stress concentration from the soft soil. In this study, extended poly-styrene (EPS) Geofoam is used to replace the soft soil over DM columns in order to control the stress concentration and settlement. To understand the effect of EPS geofoam on the degree of consolidation, stress concentration and settlement, a parametric study was carried out through a mechanically and hydraulically-coupled numerical method. A unit cell model is used, in which the soil was considered linear elastic; DM column and EPS Geofoam are elasticplastic materials. Results reveal that EPS geofoam is helpful for reducing the settlements and accelerating the consolidation. Increasing the length of the column of the deep mixed foundation with EPS geofoam has a significant effect on accelerating the consolidation.INTRODUCTIONExpanded polystyrene (EPS) geofoam is a lightweight polymeric material which is made by expansion of raw plastic beads. The expansion of the EPS beads are spherical-shaped particles containing closed hollow cells. EPS which plays an important role as an innovative lightweight construction material is now well recognized due to its low density in addition to high compressive and rupture strength. Inglis (1996) reported the first use of EPS geofoam as a seismic buffer to reduce potential seismic loads against a nonyielding basement wall. Gaskin (2000) and Bathurst et al. (2007) carried out reduced-scale shaking table test on a rigid retaining wall protected by EPS geofoam. The test data showed that the peak lateral loads acting on compressible model walls were reduced below values measured for nominally identical structure but with no compressible inclusion. Abdelrahman and El Kamash (2014) investigated the behavior of EPS Geofoam beneath raft foundation on soft soil of Port Said. They showed the ability of EPS to control vertical displacements. The investigation of the behavior of EPS geofoam with DM column has not attracted more attention of previous researchers. In this paper, the behavior of replacing the soft soil by EPS geofoam was examined in the presence of DM column."

Jan 1, 2015

By Liiban A. Affi

The most difficult task of designing multilevel tieback walls for deep excavation support is the determination of lateral stresses. These lateral stresses act not only on the shored height, but also on the embedded portion of the soldier pile, all the way down to the pile tip. Examples of lateral stresses include uniform surcharge load (soil spoils or equipment), strip load surcharge from Cooper E80 (train loads), line load surcharge (exterior footing or retaining walls), and point loads (cell tower). In this paper we will discuss the various surcharges, do step by step example calculations and show how to take the total lateral stress output and present the design pressures for direct use by the substructural designer. Included is a case study from a project Anaheim Hills, California, USA.

Jan 1, 2010

By Racquel Nottingham, Marc Mastrantuono, Freddy Lopez

In the digital era that we live in, connectivity and mobility play a decisive role in our daily activities. In this context, insufficient telecommunication infrastructure gives origin to the so called “dead zones” (areas with poor or non-existing cell phone reception), which hinder economic development in small communities and in many rural areas, since they remain invisible to a larger marketplace due to the inadequate cellular coverage. Several countries are working to identify these dead zones and with this information, establish strategies together with mobile providers in order to improve the existing mobile networks by expanding the coverage areas. As a result of the analysis, it is expected that thousands of telecommunication towers for 4G and 5G networks will be erected in the coming years. Telecommunication towers are slender elements that require large shallow foundations to verify primarily the safety against overturning. However in remote areas, it can be advisable to consider alternatives to the conventional shallow foundations, in order to optimize the use of materials (concrete, reinforcement steel, etc.). The following article presents an overview of intervention projects, where telecommunication towers were founded on micropiles. The micropiled foundations allowed to reduce considerably the dimensions of the originally planned shallow foundations. Furthermore, the use of micropiles allows for additional optimization, in combination with pre-fabricated foundations (i.e., precast concrete elements, etc.). This paper will focus mainly on the design and the execution of the micropiled foundation.

Sep 8, 2021

By Allen Cadden

The type of soil we had was a silty fine sand. It had been placed by hydraulic methods in 1904 so it was quite clean I would say less than 10% silt the rest of it was very loose sand. That I'm not certain, I've only done it on sandy soils but it would stand to reason that some sort of a number should apply because you are measuring the amount of work that you are doing to it so if the soil is fairly consistent over the site it should be able to generalize from there but I don't know for a fact that it works. Well, verifying to ourselves that this method actually worked because we weren't certain at first when we were doing it so then we would develop the numbers and then check the results.

Feb 10, 2003

By Filippo Leoni, Wesley Schmutzler

"The LPV-111 East Back Levee Improvement Project lies along the Gulf Intracoastal Waterway (GIWW) in Orleans Parish of New Orleans, La., and is an essential component of the New Orleans Hurricane Protection System. The Hurricane Protection Office of the U.S. Army Corps of Engineers (USACE) attributed failure of the New Orleans East levees system to overtopping, erosion and subsequent breaching of LPV-111 along the GIWW, as well as other sections of flood protection during Hurricane Katrina in 2005. The existing levee suffered extensive damages from Hurricane Katrina, such that the USACE elected to provide earth stabilization and to rebuild the levee sections. Due to the adverse geotechnical properties of the foundation soils, the Corps deemed ground improvement necessary to stabilize the new levee and to limit its footprint. Wet Deep Mixing Method (DMM) was selected as the most suitable technology for this task.ChallengesDesign: This reach specifically protects East New Orleans and the Bayou Savage National Wildlife Refuge, the largest urban wildlife refuge in the U.S. and home to several threatened or endangered species of birds as well as many reptiles, amphibians and small mammals. The Corps chose DMM due to the sensitivity of the protected marshlands and because the method limits the footprint of the raised levees. The increase in the load bearing capacity of the treated soil significantly decreases the footprint necessary to attain the required height increase. This limitation required the new levee to have steep slopes, drastically increasing the surcharge on foundation soils characterized by overall poor geotechnical properties (soft clays and peats). The design also considered the increased horizontal stresses on the levees due to the extreme storm surges during a hurricane.The design of the 1.6 m diameter (5.25 ft) DMM elements called for overlapping them to form a double auger element that formed buttresses perpendicular to the levee alignment. The contractor installed the buttresses at a maximum on center spacing of 4.7 m (15.5 ft). One additional double auger DMM element was midway between consecutive buttresses at the centerline of the levee to further help prevent settlement (Figure 1)."

Jan 1, 2013

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022

By Emre Biringen

"Results from a small-scale laboratory experimental program show the changes in the vertical stiffness and strength of a soft clayey soil adjacent to the shaft of an inserted pile (i.e. expansion of a cylindrical cavity). The experimental program provides a realistic axi-symmetric physical model of an element of a cylindrical pile and the surrounding soil. The study interprets the improvement and assesses its magnitude in vertical stress-strain-strength properties of a normally consolidated soft cohesive soil in response to preloading impact in the radial direction. The results verify that insertion of a cylindrical pile causes densification of surrounding soil in a radial direction due to change in stress state around the pile, and thus consolidating and stiffening of the soil.The test results indicate that most improvement in modulus and strength takes place within a distance of 4 times the radius of a pile, though significant improvement is realized to a distance of 8-10 times the radius, beyond where there is negligible effect. Settlement characteristics of the surrounding soil in a zone of 12 times the pile radius improve significantly after the formation of a cylindrical cavity. The miniature vane shear strength tests show a 1.5 times increase in a zone of 4 times the pile radius compared to the strength at 10 pile radii. The results also imply that the spacing of cylindrical piles should not be more than 4 to 10 times pile radius, so that the surrounding soil matrix may improve the vertical bearing capacity under any foundation or embankment loading.INTRODUCTIONThe engineering community is familiar with different techniques to improve the bearing capacity and settlement characteristics of weak cohesive and organic soils. Some of the in situ techniques to improve the properties of soft ground (e.g. soft clays) prior to placement of foundations are vertical preloading, deep cemenUlime mixing, stone columns, and grouting (Henn 1996; Moseley 1993). In addition to these methods, researchers have recently showed interest in achieving soft ground improvement by means of applying radial compression method for which different names exist including expanding pile (Kelleher et al. 2001 ), Preload™ Pier (Biringen and Edil 2003), and sand compaction pile (Lee et al. 2004). Handy (2001) has described how preloading can also be achieved by imposition of radial loading in soft ground with an expected improvement in stiffness. The idea behind the latter method is densification and consolidation of soft soil in the radial direction by controlled displacement for which the process can be viewed as a cavity expansion problem (Vesic 1972)."

Jan 1, 2005

By Jorj O. Osterberg

This paper is for presentation at the 14th Annual Members Conference of the Deep Foundations Institute held at the Hyatt Regency Hotel, Baltimore Maryland on October 10, 1989. This is an introductory presentation of a one hour symposium on the applications of a new testing device. This paper discusses how the device works and its uses. Papers following this describe: - How the cell is constructed and calibrated - Two projects on which the device was used on long driven piles to determine the frictional capacity - A bridge project on which the device was used on an instrumented test drilled shaft and a working drilled shaft

Jan 1, 1989

By Francisco A. Flores, Rigoberto Torres

The Complementary Technical Standards of Mexico’s City Building Code do not mention the criteria to compute the bearing capacity of Steel H-piles. It is necessary to increase knowledge in using steel H-piles as foundation elements in very soft soils of Mexico City. Considering their applicability to reinforce structures as well as new foundations in confined spaces, this research is proposed to obtain the axial load capacity of piles at scale in laboratory. This paper describes the construction and testing of scale models in laboratory of steel H-piles to measure their axial compression and tension load capacity in the soft soils of Mexico City. Three types of piles were fabricated at scale. Tests were performed on individual piles and pile groups. Based on the axial load tests, the load-displacement curves are presented both in compression and tension. The analysis of the results is shown, and comments are given regarding the ultimate bearing capacity of piles. Recommendations are presented regarding the determination of the bearing capacity of these piles in the very soft soils of Mexico City.

Sep 8, 2021

By Kim Chan, Bryn Thomas, Ben Dening

"Increased rail capacity is required into Kooragang Coal Terminal near Newcastle, NSW, Australia to relieve rail traffic congestion and improve management of train arrivals. An additional arrivals track is proposed on new embankment within a heavily constrained site located between existing railway tracks, a high pressure gas pipeline located 7m beyond the toe of the embankment and an environmentally sensitive wetland area. Ground conditions at the site consist of deep soft estuarine clays, a soil profile which is consistently encountered throughout this part of the east coast of Australia. Upon determining that a ground improvement solution was required to ensure global embankment stability, various solutions were considered including a piled viaduct, retaining walls, dry deep soil mix (DSM) columns and concrete injected columns (CICs). DSM columns were adopted as the design solution, a decision which was driven by the presence of sensitive infrastructure and a confined site. DSM offered further advantages including reduced impacts on temporary working platform design, where the use of a thinner platform could be justified owing to the lower track loads of a DSM rig relative to other ground improvement techniques.INTRODUCTIONThis paper presents a case study of the design of DSM ground improvement works to provide support for and enable safe construction of a new railway embankment over deep soft soils with a number of nearby infrastructure and other constraints. The project site is approximately 1km long and is constrained by existing railway tracks, a high pressure gas pipeline and a wetland area of ecological significance. Due to the site constraints and ground conditions, a number of ground improvement techniques were considered during the design process, with DSM columns eventually adopted. This paper discusses the design development and the particular suitability of the technique for use in this application.SITE DESCRIPTIONLandformThe site is located along the northern boundary of the Kooragang Coal Terminal (KCT) at Kooragang Island (KI), a collection of former islands located near the mouth of the Hunter River, north of Newcastle, NSW. The topography of the original area was generally flat with mudflats, swamps and mangroves existing along tidal water courses. Subsequent dredged fill reclamation and development has amalgamated the previous islands into the current KI. The site area extends over numerous channel infills including the buried former course of the Moschetto Channel (paleochannel).Figure 1 shows the proposed 1km long new rail corridor construction area in relation to the various natural and man-made site constraints including existing tracks, the high pressure gas pipeline, the wetland area and the existing reclaimed area."

Jan 1, 2015

By Mohammad Ali Rowshanzamir, Mehdi Aghayarzadeh

"This article is an effort to improve our understanding of the performance of geogrid retaining structures (GRS) through numerical analyses. The numerical modeling utilized a commercially available finite difference program, FLAC3D. In this context an extensive parametric study has been carried out on two different GRS walls (vertical reinforced block and inclined reinforced block) to investigate the influence of internal design factors such as soil strength properties and reinforcement stiffness on the performance of these walls. The main purposes of the parametric study were to (1) investigate the sensitivity of the modeling results to the input material properties, (2) examine the influence of the internal design factors on the performance of GRS retaining structures, and (3) improve the internal design of GRS walls on the basis of the working stress information obtained from the parametric study. Based on the analyses results, it was revealed that GRS walls with oblique reinforcement and reinforced block (rotated against natural backfill) have much better performance in terms of reduction in the stresses and strains of reinforcing elements as well as decrease in the wall lateral and vertical displacements in comparison with vertical reinforced block (conventional wall). For example, with 12° inclination of the wall reinforced block there was 50% reduction in the backfill settlement. Also increasing the reinforcement stiffness amount from 10MPa to 50MPa decreases the wall face displacement more than 50% in both GRS walls.INTRODUCTIONOver the past few decades, Geosynthetic- Reinforced Soil (GRS), a soil mass reinforced by geosynthetic layers to restrain the soil lateral deformations, has been employed in the construction of many types of earth structures, including retaining walls, embankments, slopes and bridge abutments. In fact GRS structures are typically more flexible (hence more tolerant to differential settlement), more adaptable to low quality backfill, easier to construct, require less over-excavation, and more economical. Nevertheless, there is a need for an accurate design tool that can predict the performance of GRS structures under working stress conditions and can predict their failure loads as well.Many studies have been published on the performance of the soil reinforced walls such as Isabel et al., 1996; Bathurst et al., 2000; Kazimierowicz-Frankowska, 2005; Nernheim and Bathurst, 2008; Chen and Chiu, 2008 Correia et al., 2012; Erlich et al. 2012. Several numerical studies have also been made throgh finite elements and finite difference techniques on reinforced soil retaining walls to analyze the wall deformations (e.g. Hatami et al. 2001& 2006, Liu and Won 2009, and Abdelouhab et al. 2011). A limited laboratory research has been reported indicating of improving effect of tilting face on GRW performance (Chen and Chiu, 2008). However no major numerical study was found on the effects of face or reinforcement tilting."

Jan 1, 2017

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.IntroductionStone column ground improvement was implemented as a means of supporting mechanically stabilized wall approaches for a new bridge over the Puyallup River, part of HOV improvements to I-5 in Tacoma, Washington. The work discussed in this case history was part of the Washington State Department of Transportation (WSDOT) I-5/Portland Avenue to Port of Tacoma Road, Stage 1 Northbound HOV contract, developed as an early work element to a follow-on bridge construction project. The area requiring stone column ground improvement is shown in Figure 1. The improved ground supports permanent geosynthetic walls and embankments up to 50 feet high. This wall can be seen in Figure 1. The selected ground improvement primarily provides global stability of the soils beneath the walls during anticipated seismic loading and also reduces the time and magnitude of consolidation settlement under the weight of the planned embankment.Approximately 74,000 cubic yards of liquefiable alluvial soils were improved by stone columns. Stone column construction occurred in late 2010 and early 2011. This was followed by the embankment and wall construction. Settlement monitoring began with the embankment construction and continued into 2012."

Jan 1, 2017

By Jamey Rosen, Georgette Hlepas

"Bluestone Dam is a concrete gravity structure with an overall length of 2,060 feet and a maximum height of 165 feet above the streambed. Several major project modification designs have been implemented and additional modifications are currently in construction and design phases. Due to the various modifications since original construction was completed in 1948, detailed documentation with visualization of the project features is needed. A three-dimensional model of the internal and external features of Bluestone Dam was generated from LiDAR data, survey information, and other data sources. One of the key features of interest in this model is an accurate visualization of over 200 dam anchors based on downhole anchor surveys. The model is accessible in Microstation and Geographic Information Systems (GIS), allowing users to rotate the anchors in three dimensions; view them in the context of geology, internal dam structural features, historical construction records, site photographs, bathymetric data, and instrumentation data. Users can “click” on individual anchors to view associated construction details and open a comprehensive installation packages. The model will be used by the United States Army Corps of Engineers (USACE) as part of a larger Geospatial Data Management System as a historical accounting of the project construction data, and be a long-term living document for use by both design engineers and operations staff to assess dam safety risk and to design future project modifications.IntroductionDuring the life of any project, critical data concerning the construction and performance history are required to be collected and maintained. The data collected prior, during, and post-project construction help with the design process, ensure that the project is built to specifications and is performing as per design intent. During the Post-Implementation Evaluation (an evaluation performed after a major project modification), these data are used to visualize the repairs, verify the construction was performed per design intent, and document the history of the construction phases, associated test results, and overall effect on the project. The project described in this paper is the construction of a system of tools to effectively use these data.Data collected and maintained during the operations phase helps to ensure that the project is continuing to perform as per design and aids in advance warning of any potential failure or required maintenance. Dam Safety, Emergency Management (EM), and Operations and Maintenance personnel can use the system to verify the status of the project in preparation for a high flood event. For example, if there is repair work being performed on a critical feature of the project that would affect the operation of the dam structure during a flood event, Operations personnel would be responsible to update the status of the system such that Dam Safety and EM would be able to identify the feature that is out of service, its date of expected repair completion, and the implications during a flood. In addition, risk assessments typically require a full history of the project and its performance. Any concerns that arise concerning the safety or performance of a project will require a full documented history of the project and its components. Proper documentation and data management are key in this assessment process."

Jan 1, 2016

By Edward C. Clukey

A deep mixing method (DMM) foundation was selected by the Project Team for a very largeLNG facility in West Africa. As described in a companion paper, this foundation consists of alarge number of columns installed by mixing cement with in-situ soils. The foundations arearrayed as a variety of honeycombed type configurations which, if installed to desiredspecifications, can provide a robust foundation alternative. The foundation is capable ofdistributing loads and limiting settlements even if some of the soil in the columns is not fullymixed during installation. An important part of the overall quality assessment program,therefore, involved developing a testing program to verify the methodology. In addition theimpact of potential defects in columns on the overall foundation integrity had to be assessed.This paper describes some of the preliminary work done to establish the requirements for thequality assurance program. A key component of this program involved the samplingfrequency used to assess potential defects in the columns. To verify the column integrity 104-mm samples were taken continuously at a selected frequency through the 23 m longcolumns. The preliminary work described in this paper demonstrated that the appropriatesampling frequency depends on both the desired reliability level as well as the number ofdefective columns encountered during testing. Initial finite element analyses were performed to assess the extent that defects could occur incolumns within the honeycombed structure without adversely affecting the overall foundationintegrity. The results from this work demonstrated that the spatial location of the defects wascritical to properly assessing the foundation integrity. In addition to column sampling a load test was performed as part of the foundationverification process. The methods used to apply appropriate loads so that loads at thebottom of the columns approached design values are discussed in the paper. The results obtained from this preliminary study were then used to help develop a morecomprehensive assessment program, described in a companion paper, to determine therobustness of the DMM foundations for both the LNG processing facilities and a condensatetank.

By Thomas M. Caruso

Construction of a new ship dock at a major Philadelphia area refinery required geotechnical design and field consultation. The new dock, which consists of a system of mooring dolphins and platforms, will be capable of docking the Stena V-MAX Oil Tanker (V-MAX). The 1100 ft long V-MAX is currently the largest tanker to travel the Delaware River and will induce significant lateral loads on the new ship dock. Lateral loads induced on the dock will be resisted by over 200 pipe piles installed on a batter. The piles used for support of the dock included 20 and 30 in. diameter reinforced, concrete filled pipe piles. Complete construction of each pile included driving of the pile to the design ultimate capacity, flushing the pipe pile casing clean of overburden materials followed by drilling rock sockets into the underlying Wissahickon Formation. Variations in depth to bedrock, rock quality and degree of weathering and presence of very hard quartzite lenses created a complex geologic environment that presented challenges for the pile/rock socket design and installation. The design of the pile system, installation methods, QA/QC and testing (Pile Dynamic Analysis), as well as the challenges that were encountered through the duration of the project are presented and discussed.

Jan 1, 2008

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By Benjamin B. Buensuceso III

Crosshole sonic logging (CSL) is a popular quality assurance and quality control method used to examine the concrete quality of cast-in place deep foundations, though the evaluation of the results is subject to certain limitations. One such limitation explored in this paper is the occurrence of false positives, where signal anomalies indicated by CSL test results are not necessarily indicative of imperfections in the foundation that could affect its performance. A case study of false positives evaluated in CSL records in a major infrastructure project in Metro Manila is presented in this paper. A detailed desktop evaluation and results from complementary high-strain dynamic load testing and low-strain pile integrity testing were used to evaluate the significance of the suspected false positive signal anomalies from the CSL test results. Recommendations for the proper interpretation and evaluation of CSL test results in Philippine practice, given the method’s limitations and examples presented, are also shared.

Sep 8, 2021

By Guilherme L. M. G. Carvalho, Zachary T. Fleming

In a world of 2-dimensional design documents, envisioning and understanding 3-dimensional interferences for complex foundation construction scenarios can be challenging. Videos and computer models serve as 3-dimensional spatial aids but have drawbacks related to a fixed perspective. Augmented and virtual reality (AR/VR) provide new tools to communicate design challenges and improve construction planning. This paper provides a practical look at the basics of AR/VR systems and the tools available to the foundation design and construction industry by giving a high-level example of the technologies’ use in the design and delivery phases of a complex micropile installation project for the remediation of a dam foundation. Using these technologies, GEI was able to design and deliver a complex foundation remediation solution. AR/VR benefited regulators, and the client, to help understand the design concept, construction sequencing, and approach to overcoming installation challenges. Due to its user-friendly nature and less rigorous programming and hardware requirements, AR proved to be more useful than VR for this scenario. AR/VR will likely not replace videos and computer models; however, it can be a useful 3-dimensional visualization aid that complements the project delivery process and offers benefits that traditional methods cannot. INTRODUCTION Augmented and virtual reality is a promising and rapidly developing technology within the engineering and construction world. Like any rapidly developing new technology, the language describing it can be confusing and dynamic. To eliminate the confusion some definitions must be made. AR/ VR definitions The definitions of virtual reality (VR) and augmented reality (AR) for the purposes of this paper are as follows: VR is a computer-generated immersive environment that the user experiences within a digital 3- dimensional space (Satava, 1993)AR is a composite view created by superimposing digital objects into the user’s real-world view (Azuma, 1997). Often, VR is used in an office environment and allows the user to “visit” the digital site to review site planning, construction sequences, and interference geometry. AR can be utilized in both the office and onsite environments. Like VR, the in-office application for AR is commonly site planning. AR also can be utilized in the field for applications such as seeing through the ground to locate known existing obstructions like utilities, gas tanks, etc.

Jan 1, 2019