Search Documents

"Full time inspection of drilled shafts by qualified personnel is a necessary part of construction. Detailed inspection procedures for routine inspection are provided in the Drilled Shaft Inspector’s Manual, published jointly by the DFI and ADSC: the International Association of Drilled Shaft Contractors.The use of NDT methods or other observation methods, such as probes, video camera inspection, remote shaft wall inspection devices or various calipers are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT and other "remote" or indirect observation methods are valuable alternatives to direct entry of personnel into drilled shaft excavations. They should be considered whenever appropriate to reduce the risks of direct entry of personnel into drilled shaft excavations.As described in the Drilled Shaft Inspector’s Manual, observations made during construction are essential for quality construction of drilled shafts. The shaft depth, diameter, plumbness, bottom conditions, reinforcement, concrete continuity, and bearing conditions are most easily checked during construction. Some of these observation methods include excavation around the shaft for relatively shallow inspection, down-hole inspection for end bearing conditions or rock sockets, and video camera devices for remote inspection. In rare circumstances, a drilled shaft can be extracted for inspection. Before concrete placement, the bottom of the shaft can also be probed by drilling or coring to determine if there are voids or soft zones in the material at the base of the shaft.The Drilled Shaft Inspector’s Manual focuses on traditional "topside" inspection for routine drilled shaft construction."

Jan 1, 2004

By Lance A. Roberts

The Federal Highway Administration (FHWA) has mandated the use of the AASHTO Load and Resistance Factor Design (LRFD) specifications for all new federally-funded transportation infrastructure projects beginning in October 2007. This includes the design of all geotechnical-related elements, such as deep foundations, which have historically been excluded from the LRFD requirements. The basis of the LRFD specifications is the application of a probabilistically computed parameter called a resistance factor to the foundation capacity in lieu of the traditional, and often arbitrary, factor of safety. Therefore, the process of computing resistance factors for use in the design of deep foundations is extremely critical to ensure a safe, efficient, and consistent design methodology. In this paper, various methods to calibrate resistance factors for use in the design of deep foundations are examined. The methods that are currently utilized to calibrate the resistance factors reported in the AASHTO LRFD specifications may be classified as the allowable stress design (ASD) method and the reliability theory calibration method using static capacity prediction techniques. These methods are compared to a ?t-z? model design methodology. The current methods focus exclusively on the strength limit state design of deep foundations. The advantage of the ?t-z? model methodology is that it can be utilized for both strength and service limit state design. In addition, the results show that resistance factors vary based on geological setting, construction method, failure criteria and deep foundation type. This variability in the resistance factors should therefore be integrated in the design to ensure that the objectives of the LRFD approach are satisfied.

Jan 1, 2008

By Bartho J. Admiraal

"As part of the Schiphol-Amsterdam-Almere project, the largest aqueduct in Europe is being built in order for the A1 motorway to cross the Vecht River. The A1 consists of 12 lanes and the total width of the aqueduct will be 65 m (213 ft). The total length of the structure will be 620 m (2035 ft). Speed of construction is essential for the DBFM-contract, which forms the primary reason for choosing a building method with a horizontal water retaining barrier created by low pressure grouting. After final checks on the water tightness of the silica based layer (softgel), excavation to a depth of approximately 12 m (40 ft) below the water table could be started in order to build the aqueduct.This paper presents a new approach for the calculation of the required grout volumes needed to ensure a “softgel” layer without gaps or holes. The approach applies measurement of deviations due to execution aspects in a probabilistic model. With this model, one is able to study the effects in a field application, i.e. multiple rows of grouted spheres. The results are visualized in order to analyze the risk of holes more easily. It is evident that the existence of a hole means a major leakage. By completing multiple runs, the strategy for grout volumes can be adjusted to minimize this risk.INTRODUCTIONThe Dutch Department of Waterways and Public Works invests over € 4 billion between 2012-2020 to increase the capacity of 63 km (41 mi) motorways of one of Holland’s major corridors. The A1/A6 will be transformed over a distance of 20 kilometers (13 mi). Near Muiden, the current drawbridge on the A1 for crossing the Vecht river will be replaced by a new aqueduct to be located slightly south of the existing bridge."

Jan 1, 2016

By Renzo D. Verastegui, T. C. Michael Law, Sitotaw Y. Fantaye, Alfredas Daugiala

"When completed, 520 Park Avenue will amend the Manhattan skyline and be one of the most prestigious high rise towers in New York City. The 52-story condominium building is located on a 60 by 100 feet lot on East 60th Street between Park and Madison Avenues. The geographically complex site is bounded by two fragile 5-story masonry buildings on the east and west, a mid-rise building on the north, and a New York City subway tunnel on the south. To add to this complexity, the ambitious development required 70 to 80 feet of excavation, mostly below groundwater level in highly permeable rock, to accommodate four levels of cellars. The new building also cantilevers 24 feet over a five-story historic building on the east. The limited footprint of the building coupled with large compressive and tensile axial loads, considerable base shear and over-turning moments, and the required deep excavation, presented unique foundation challenges. This paper describes how the challenges were solved with an innovative combination of permanent secant pile walls and drilled shafts.INTRODUCTIONThe project site is located at 45 East 60th Street, on the block bounded by East 61st Street to the north, East 60th Street to the south, Park Avenue to the east, and Madison Avenue to the west. As shown in Fig. 1, the site is surrounded on three sides by buildings sensitive to differential settlement. In addition, a NYCT underground subway structure lies below East 60th Street approximately 13 feet south of the site. The base of the subway structure is approximately 42 feet below the street.The project consisted of constructing a 52-story tall building. A portion of the superstructure cantilevers 24 feet over an adjacent five-story historic building. The underground construction for the new building involved a four-level basement, extending about 60 feet below ground surface. The excavation subgrade is much deeper than both the subway structure and the adjacent shallowly-founded building foundations."

Jan 1, 2016

By Monica R. Garcia, Antonio Alberto S. Correia, Paulo J. Venda Oliveira

"The aim of this paper is to analyze the creep behavior of a Portuguese soft soil stabilized with binders in one-dimensional conditions, based on oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. The results show that the best binder type for this soil, in terms of creep behavior, is composed of Portland cement and fly ash with a dry weight proportion of 75/25, as this promotes the development of secondary pozzolanic reactions. The results also show the decrease in the secondary compression index with the increment of the binder content, since it promotes an increase in the cementation bonds between soil particles. The general analysis of the results shows a clear dependence on C??and qu, until values of qu of 1500 kPa; after that this relationship is negligible.INTRODUCTIONThe geotechnical structures (such as embankments, dams and buildings) built on organic soils exhibit notable creep deformations, which increase the maintenance and exploitation costs and can even compromise their functioning. To attenuate the creep effects of the soft ground, some improvement techniques are frequently used, such as preloading or reinforcing the soil foundations with vertical rigid inclusions, like concrete piles, stone columns or deep mixing columns (DMCs). However, the installation of DMCs in the soft ground induces (via the arching effect) a transfer of stresses from the soft soil to the DMCs, which causes an increase in the creep settlement on the DMCs (Venda Oliveira et al. 2011).Notwithstanding the fact that the creep behavior of clays has been the object of several studies (Leroueil et al. 1985; Mesri and Castro 1987; among others), the study of the creep behavior of soil-binder admixtures has been practically ignored by the scientific community. The few studies on this theme have revealed that a stabilized soil’s creep behavior is dependent on: the type of binder (Venda Oliveira et al. 2013), the binder content (Correia 2011; Bobet et al. 2011; and Venda Oliveira et al. 2013), the stress level applied during the creep phase (Venda Oliveira et al. 2013), the organic matter content of the natural soil (Venda Oliveira et al. 2012; 2014), and the curing conditions (humidity, vertical stress applied during curing, and curing time) (Correia 2011; Venda Oliveira et al. 2012).The aim of this paper is to contribute to a better understanding of the creep behavior of a soil-binder admixture, by examining the results of oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. Additionally, the creep behavior is correlated with the effective vertical yield stress and the unconfined compressive strength (UCS)."

Jan 1, 2015

By Krishna R. Reddy, Jyoti K. Chetri, Girish Kumar

Geotechnical engineering encompasses a major portion of the civil and infrastructure projects. The large amounts of energy and resources typically used in these projects leads to undesirable emissions and wastes which contribute substantially towards global environmental impacts (e.g., global climate change). This could further include secondary economic and societal issues which are often unaccounted in traditional engineering design of the geotechnical projects. In order to address this issue, it is imperative to integrate the broader environmental, economic and social implications into decisions of a geotechnical project. Recent years have seen a major impetus on life cycle assessment to evaluate the environmental sustainability of the geotechnical designs. However, there are no tools that can quantify the life cycle triple bottom line sustainability of potential design alternatives in a project with holistic considerations towards broader economic (indirect costs and benefits) and social impacts (stakeholder preferences, socio-environmental and socio-economic impacts). This study presents a new framework for quantitative assessment of life-cycle sustainability (QUALICS) for alternative designs in engineering projects. The framework integrates two multi-criteria decision analysis methods namely, the Integrated Value Model for Sustainable Assessment (MIVES) and Analytic Hierarchy Process (AHP), to support decision making on the potential design alternatives. In this study, a brief overview of the framework is presented. A case study demonstrating the use of QUALICS framework is discussed with its application to the sustainability assessment of two deep foundation systems, caissons and piles, over their design life. The technical designs of both systems are developed based on bearing capacity, both primary and secondary settlements, and structural integrity. The results from the sustainability assessment of the two deep foundation systems are discussed, and the most sustainable option based on different stakeholder preferences and site-specific conditions are identified.

Jan 1, 2019

By Timothy C. Siegel, Paul J. Axtell

The Missouri Department of Transportation (MoDOT) recently replaced the Hurricane Deck Bridge that carries Highway 5 traffic across the Osage Arm of the Lake of the Ozarks in Camden County, Missouri. The former bridge was constructed in the 1920's and was supported on pneumatic caissons bearing on dolostone bedrock. The replacement structure is founded on drilled shafts socketed into the bedrock. During the design phase of this bid-build project, a baseline design was developed and Alternative Technical Concepts (ATC's) were allowed from approved contractors. Those ATC's were confidential and not shared between teams. Either the baseline design or the approved ATC design could be bid by the respective contractors. The baseline design included re-use of the 90-year old caisson foundations. Accordingly, an extensive evaluation of the caissons and underlying bedrock were conducted by coring, laboratory testing, acoustic tele-viewer (ATV), and cross-hole sonic logging (CSL) methods. The results of the investigation indicated the caissons were in excellent condition and suitable for re-use. However, a more cost-effective ATC was submitted, awarded, and constructed that did not re-use the existing caisson foundations but rather reduced the span lengths, increased the number of piers in the water, and supported those piers on drilled shafts. Interestingly, the difference in low bid price between the awarded ATC and the baseline design was less than one percent of the construction cost. This paper describes the multiple foundation designs that were necessary for this interesting project. The various foundation evaluations include the existing pneumatic caissons, large-diameter open-ended pipe piles to support the baseline design, and the design of rock-socketed drilled shafts that were successfully constructed in 2012.

Jan 1, 2017

By Raymond E. Sandiford

"The redevelopment of the World Trade Center (WTC) provided an opportunity for the Port Authority of NY and NJ to complete a long sought underground connection between all of Lower Manhattan’s transit lines, the World Trade Center and the World Financial Center (WFC) (Figure 1). Creating this connection was a challenge because the WFC lies west of the heavily trafficked Route 9A, also known as West Street. The previous connection was a bridge that required pedestrians to make significant level and directional changes to navigate the crossing. The positioning and elevation of the Route 9A pedestrian tunnel was established to provide pedestrians with a clear, single level, climate controlled corridor from the new WTC Transit HUB to escalators leading into the WFC Winter Garden.As the most direct link to the WFC, tens of thousands of people a day will use the pedestrian corridor. To accommodate this large number of pedestrians and provide an obstruction free passage, the tunnel has a clear width of 50 ft (15.2 m). Although only 250 ft (76.2 m) long, that short length presented many technical challenges.Here I describe how the challenges were overcome during the construction. However, some of the truly problematic issues arose from coordinating the phasing of this project with adjacent construction activities at the WTC, the reconstruction of Route 9A, and the WFC’s redevelopment program. The limited access to the excavation areas and confined site logistics were further complicated by having to maintain six lanes of traffic on Route 9A at all times. The efforts were so intertwined that, well into the underpass construction, the Port Authority Construction Department decided to merge a portion of that work into the WFC redevelopment."

Jan 1, 2012

By Austin Metz, Kevin Stanton, Ramin Motamed

"A recent study calibrated Load and Resistance Factor Design (LRFD) resistance factors for local soil conditions in the Las Vegas Valley. As a part of this calibration, an extensive database of drilled shaft load tests and associated subsurface soil information were collected and compiled. This database, deemed the Nevada Department of Transportation Deep Foundation Load Test Database or NDFLTD, was designed with the presentation of load test data, the subsurface soil conditions, and the spatial distribution of the data in mind. In addition, the NDFLTD was developed in a way that allows additional data to be added as it becomes available. As such, the rules of database normalization were followed to allow for additional and different types of data to be added to the database and reports. Microsoft Access was chosen to present the data because it is easily accessible to anyone with Microsoft office software, it has a quick learning curve, and it has the ability to present a relational database. The largest obstacle faced when creating the NDFLTD was normalizing the data used in the LRFD calibration, with the goal of reaching the 5th normal form.INTRODUCTIONLRFD is based on statistical performance of engineering components, as opposed to the more traditional Allowable Strength Design (ASD), which divides the strength of a component by a safety factor. Calibration of resistance factors for LRFD requires a robust statistical analysis of past performance. For drilled shafts this requires a database of full scale load tests (Abu-Hejleh et al. 2014). The FHWA developed the largest US based deep foundation load test database, deemed the DFLTD, collecting data from 1985 to 2003 when funds ran out (Abu-Hejleh et al. 2014). Recently, the DFLTD has been updated to modern standards (Petek et al. 2016). In October of 2007, the FHWA mandated state department of transportations (DOTs) to follow AAHSTO LRFD guidelines for their highway foundation designs (Abu-Hejleh et al. 2014). Since then multiple state DOTs have developed their own, region specific deep foundation load test databases. Florida has a long history of developing databases for deep foundation LRFD resistance factor calibration, with the two main databases being the FL database, and The Deep Foundations Database (Abu-Hejleh et al. 2014). Iowa developed a Microsoft Access based database in 2014 (Garder et al. 2014). Oregon developed a database compiling pertinent data from the DFLTD, Florida DOT’s Deep Foundation Database, as well as from other databases (Smith et al. 2011). Illinois developed the “International Database” for static and dynamic reliability based calibration (Long et al. 2009). Louisiana developed a database for LRFD Calibration of driven piles in 2009 (Abu-Farsakh et al. 2009). The California Department of Transportation has its own internal foundation database, which is housed within the Foundation Testing Branch archive (Smith et al. 2011). In 2016, the Nevada Department of Transportation (NDOT) presented its own LRFD calibration for the Las Vegas Valley (Stanton et al. 2017), and the NDFLTD was developed as a part of that project (Motamed et al. 2016)."

Jan 1, 2017

By Matthias Baeßler, Markus Herten, Ernst Niederleithinger, Steven Georgi

"Abstract: BAW and BAM have performed a large scale comparison and calibration test on static and dynamic load capacity evaluation of bored piles in glacial sandy soil. The test was performed using eight piles at the BAM test site for technical safety at Horstwalde 50 km south of Berlin. The test area has been prepared and investigated in great detail using boreholes, cone penetration tests, pore pressure sensors and geophysical methods to assure controlled conditions for all piles and tests. The piles (10 m length, 0.9 m diameter) are mainly friction piles (low toe resistance) and have been checked by integrity testing. Five piles have been tested by five contractors using the dynamic method in a blind experiment, the other ones piles by static load and/or later on by the dynamic method. Some piles have been equipped with additional fibre optic instrumentation which proved to be robust and helpful in interpreting the results of static, dynamic and integrity tests. We have experienced a deviation of the dynamic load test results gathered in the blind experiment from the static values of up to 20% in most cases, sometimes even up to 30%. This can be related to the known soil inhomogeneities, interpretation and modelling in CAPWAP and method inherent uncertainties. In cases where the static values were known by the testers for calibration, the deviations were significantly smaller. It has to be taken into account, that the two static load tests showed different results as well. Due to the low toe resistance, use of a big drop weight (11 tons) and large drop heights most piles suffered from cracking, which was clearly seen in follow up integrity tests and confirmed by excavation. The piles are available for further research.IntroductionBored piles are used in many construction projects of the German waterways authorities, e. g. bridges, piers or locks. Their load carrying capacity varies with pile type and geometry as well as soil type, parameters and structure and is thus not easy to calculate in advance. Dynamic pile testing as a cost effective addition or replacement for expensive load tests is accepted in many places (Beim and Likins 2008) but still doubted in others. Inspired by the international prediction event for piles in residual soil carried out in the frame of ISC’2 (Viana de Fonseca and Santos 2008), governmental research institutes have designed an experiment in a geological setting typical for glacial and post-glacial areas in northern Germany. Some results have already been presented by Niederleithinger et al. (2012), Herten et al. (2013) and Baeßler et al. (2013). It was intended to perform a blind test for load capacity estimation using dynamic pile testing on six drilled shafts involving five test crews. Two other piles would have to be tested thereafter using static and dynamic methods."

Jan 1, 2014

By Yazn Khasawneh Ph. D. P. E., Will Tjaden, Spencer E. Ness P. E., Mohammed Nasim Ph. D. P. E.

Wind turbine components undergo many loading cycles during their operational life. Additionally, wind turbines may undergo extreme loading conditions from natural hazards, mechanical failures, or emergency stops. Current design practice for the foundations of wind turbines accounts for these complex loading conditions through a simplified pseudo-static approach based structural loading combinations. A rotational stiffness for the foundation is estimated from the pseudo-static analysis and then compared to an acceptable minimum rotational stiffness provided by the turbine manufacturer. These minimum rotational stiffnesses are based on dynamic analysis of the tower and nacelle system with the foundation represented as linear springs. This approach provides a reasonable approach to the foundation design but does not accurately capture the true dynamic performance of the entire soil-foundation-tower-nacelle system. This becomes especially important for pier-type foundations, which are being more commonly used to support modern and future generations of larger turbines. Additionally, the dynamic performance of the foundation will vary as the adjacent soil undergoes a large number of loading cycles of varying strain magnitudes. In this study, the full turbine-tower-foundation-soil system was modeled using finite element methods. An advanced non-linear soil constitutive model and dynamic loading time histories were used to investigate changes in stiffness of the soil, and the possible impact on the dynamic response of the system. Results were compared to conventional design methodologies with the goal of reducing foundation capital costs while avoiding increases in O&M costs and which can lower the LCOE of wind energy.

Oct 1, 2022

By Eric S. Lindquist, Charles A. Luxford

The State of Texas recently adopted a master plan to expand the existing Capitol Complex in Austin. Phase 1 of this expansion will add two new State office buildings and five levels of underground parking to the existing Complex. Additionally, a landscaped pedestrian mall will be built atop a portion of the underground parking to enhance the area as a cultural destination. Capitol Complex website: https://www.tfc-ccp.org/ Brierley Associates was selected to provide detailed design of the entire Phase 1 earth retention system for an approximately 40-65 ft (12-20 m) deep, 500,000+ yd3 (380,000+ m3) excavation through overburden soils and limestone bedrock. To facilitate overall project coordination, all design packages were required to develop Revit models, including the retention system package. With the project located in an urban setting, this 3D model also facilitated coordination of the retention system with adjacent major structures and utilities. The retention system is a combination of soil nails, soldier piling with tiebacks and rock anchors with a shotcrete facing as a substrate for the below-grade blindside waterproofing system. Due to the substantial scope of excavation, a significant number of utilities had to be routed on a temporary span over the excavation. Brierley Associates designed this utility support structure, which required extensive coordination with the excavation support and existing utilities located directly underneath the structure’s foundations. Preconstruction geotechnical work identified a fault zone that might be encountered within the excavation; however, the fault feature was found to have a more adverse location and orientation than originally anticipated. This observation required that a portion of the temporary anchors be converted to higher-capacity, corrosion-protected permanent anchors.

By N. Aarthi, G. R. Dodagoudar

The improvement of soft clay deposits using stone columns is a well-established ground improvement technique in the western world. This technique has been well documented and has proper design codes for precise execution in the field. The sand compaction pile (SCP) method is a contemporary technique to stone columns and has limited literature related to the strength characteristics of the loose to medium dense sand deposits treated with SCP. The available studies on the SCPs installed in cohesionless deposits focused on the improvement by indirectly assessing the SPT-N values pre- and post-installation of the SCPs. The widespread implementation of the SCP technique in recent years has increased the need for a more direct evaluation of the improvement. Earlier studies in this regard have revealed that the available design solutions are based on the type of installation equipment, their working efficiency, and accumulated field data. However, it is found that there are no generic design codes for the direct estimation of the ultimate bearing capacity of the SCP improved cohesionless deposits. To meet the design requirement for the SCP treated ground, a series of experimental and numerical investigations are performed in the present study to arrive at a direct framework in the form of design charts based on the pressure-settlement response of the treated ground. The developed design charts give the ultimate bearing capacity (UBC) of the treated sand deposit for the known initial relative density (RD) of the deposit, spacing and diameter of the SCPs, size of the footing, and for the specified target unit weight required for the intended application. It is concluded that the design charts will be of preliminary use to the design engineers to directly evaluate the UBC of the SCP improved loose to medium dense cohesionless deposits as part of the SCP method of ground improvement. It is expected to have more field-scale experiments and in-depth analysis before implementing these charts for actual field execution.

Nov 1, 2022

By Ekhlaq A. Khan

"The new third Bridge over Narmada River at Bharuch which was recently completed is characterized by some aesthetically appealing elevations of the pylon and large size of the deck. This paper gives an insight to design and construction technique adopted for foundation construction of Extra-dosed span - 3 rd Narmada Bridge at Bharuch over river Narmada, Gujarat. Site being located in intertidal zone had its unique geological characteristics and own set of difficulties during construction.INTRODUCTIONThe Indian subcontinent offers diverse subsoil conditions. With current modern and future trend of long span bridges the substructure design often demands large size foundations. The foundation of theses bridges are usually deep and large in size. The execution of such foundations in maritime environments often involves important temporary works, in order to provide a safe workplace, comply with environmental requirements and achieve high quality standards.Often Pile foundations are preferred solution now a days, but due to various statutory and environmental regulations their construction poses a challenge. With better equipment and corresponding quality control, construction of large diameter pile foundation has emerged as a faster and reliable option.OVER VIEW OF THE PROJECTThe first two lane bridge on NH-8 (Vadodra – Mumbai) known as Sardar Bridge was constructed in 1977, subsequently an additional two lane bridge was constructed in 1999-2000, 29 m downstream of the first. In view of rising volume of traffic and as part of upgradation of NH8, National Highways Authority of India (NHAI) proposed to construct 3rd new 4 Lane Bridge 100 m downstream of 2nd Narmada Bridge, based on Central Water and Power research Institute (CWPRS) study and recommendation.The general layout (fig. 1) of the 3rd Narmada bridge has 8 spans of 144 m and 2 spans of 96 m with total length of 1344 m, supported by132 nos. of 1.5 m diameter piles of about 50 m depth. The substructure has leaning “Y” shaped lower pylon of height 30 m together with cast in situ pier diaphragm. The piles are of M40 and superstructure & pylon of M50 grade of concrete."

Jan 1, 2017

By George G. Goble

The use of augercast piles has been limited by the engineer's concern for the structural quality of the installed pile. The nature of the pile is such that its final structural continuity is very dependent on the skill of the personnel that do the installation. Thus, NDT methods have been used to verify integrity and when problems are indicated the available solutions are usually quite costly. If information were available during the pile installation so that immediate steps could be taken to correct perceived problems, the concerns of the engineer could be addressed and the system would gain increased reliability. Pile Dynamics, Inc. has developed a quality control system, the Pile Installation Recorder for Augered Cast-in-Place piles (PIR CFA). This system consists of the following devices as shown in Figure 1. 1) The Control Unit powers the sensors, conditions the signals from the sensors, records all measurements, takes input information from the operator, displays the results, and stores the recorded data on a flash card for later permanent storage and processing. During the use of the system all of the results obtained during a test are seen during recording and can be reviewed on the screen again after completion of the installation. The ability to review the measured information makes it unnecessary to print a copy in the field. Since printers often give difficulty in the construction site environment the ability to review the results quickly after completion of the installation is an important capability.

Jan 1, 1997

By P. V. Chandramohan

"In ports, piled berths are designed and constructed for berthing of ships with a finite draught. Piles in a bridge foundation also have a large free stand above scoured level. The piles of these structures have to withstand large horizontal forces imparted by the impact of the approaching vessels or due to longitudinal and transverse action in a bridge. It is also imperative that these piles have to project out of the dredged / scoured bed. These piles are normally designed as slender compression members subjected to bending also. They are subjected to vertical load tests for assessing the soil resistance. Lateral load tests, as a rule, are also stipulated. IS and IRC codes stipulate a deflection criteria for lateral load test to arrive at the capacity. These tests are usually conducted on a working pile by jacking out two piles. At the time of the test, pile will be free headed. But in service, piles are fixed head. There is a large difference in deflections between a fixed head and a free headed pile. Besides, a free headed pile will be subjected to a much higher bending moment than the fixed head one. This will put the working test pile under risk of breaking during the test. The problem is analyzed with case studies. INTRODUCTION Vertical capacity of piles is assessed by static formulae. This formula is based on the soil properties obtained from random soil exploration and laboratory and in-situ testing. Since soil is not a homogeneous medium, properties can vary. The design parameters taken for computations may be different from the ones at the interface of the pile with the soil. The best way is to find out is by a load test. The code IRC:78-2014 has rightly stated that initial load test is part of the design process. This is true with the vertical load test. But there are certain problems with the purpose and inference of the lateral load test. In both the tests the criteria for acceptance is the quantum of movement of the point of application of the load. In the former, the movement is vertical and depends more on the compression of the soil than the compressive strain in concrete. But in the latter, this movement is partly on account of the flexural rigidity of the pile and partly due to the horizontal compressibility of the soil. The role of rigidity of the pile is more when compressibility of the soil is higher. Lateral load test is done by jacking one pile against another because it is difficult to get an independent horizontal reaction. Please see Fig.1 Photo."

Jan 1, 2015

By Pancho J. Garza, Keith H. Dahlen, Chris A. Labye

"Design for reconstruction of the East Flagstaff traffic interchange project located in Flagstaff, Arizona posed particular challenges. The proposed design included construction of a nearly 50-foot tall mechanically stabilized earth (MSE) wall given rightof- way constraints and soft subgrade soils. The tight right-of-way, approximately 15 feet in certain locations, adjacent to existing structures limited the number of viable remedial alternatives to provide grade separation at the proposed bridge abutment without significant settlement. Preliminary analyses indicated the existing subgrade soils - consisting primarily of relatively soft silts and clays with decomposed pumice - would settle approximately 12 to 14 inches resulting in unacceptable wall deformation. Stone columns placed via vibratory methods (vibro-replacement) consisting of circular excavations which penetrate to firm bearing soils and which are filled with crushed stone were selected to densify the existing subgrade soils. The implemented mitigation measures helped limit settlement to less than one inch and allow for successful construction of the project. The project history - including site constraints, subsurface conditions, evaluation of remedial alternatives, stone columns methodology, and effectiveness of ground improvements - will be discussed.IntroductionThis paper describes the subsurface investigation performed for the reconstruction of the Business Route 40 (B-40) (Country Club Drive) and United States (US) 89 Traffic Interchange (TI) located within the city limits of Flagstaff, Arizona. This project is currently referred to as the East Flagstaff TI. The Project Site Vicinity Map is shown below.The former B-40/US 89 TI was considered ineffective in handling the current and projected volumes of traffic which transition from northbound (NB) B-40 to US 89 (both directions), as well as from southbound (SB) US 89 to SB B-40. The intent of the project was to reconstruct the TI to better accommodate projected traffic volumes. The project eliminated the existing ramps from both NB B-40 to SB and NB US 89. The new interchange includes a Tee intersection from B-40 to US 89. In order to accommodate this alignment, the profile of US 89 was raised several feet (on nearly the same as existing horizontal alignment) to match the elevated profile of B-40. B-40 was shifted just west of its current alignment to accommodate construction of a new, wider bridge structure which spans over Industrial Drive, the Burlington Northern Santa Fe (BNSF) railway, and old Route 66. South of the new bridge, B-40 transitioned back to the existing alignment just north of the I-40/B-40 TI. Within the project limits, both US 89 and B-40 were widened to three travel lanes in each direction."

Jan 1, 2015

By John P. Turner, Benjamin J. Turner

"This report describes a research project for evaluating the applicability of the widely accepted 80 percent criterion for elongation of ground anchors to anchors with unbonded lengths exceeding 100 feet. This issue is driven by several recent projects involving ground anchors for landslide stabilization in which a significant percentage of the anchors did not meet the criterion that requires measured elongation during proof load testing of at least 80 percent of the theoretical elastic elongation. The projects involved anchor unbonded lengths in the range of 85 to 220 feet, which is outside the range traditionally used in practice, although anchors of this length are being used more frequently for landslide stabilization. The principal objective of this research is to address whether the widely accepted criterion of 80 percent elongation is applicable for such applications, and whether other factors affect the ability of anchors to meet the criterion.Analytical methods for predicting transfer of load along the length of steel strand due to friction loss are used routinely in the prestressed concrete industry. These analytical expressions provide a rational framework for quantifying changes in load due to friction along the length of a ground anchor in terms of a ‘wobble coefficient’ (K) as defined in Aalami (2004). Values of the wobble coefficient for ground anchors can only be determined by back-calculating from load tests, i.e., fit the value of K to the appropriate analytical expression based on the known test load and measured percent elongation. The analytical basis is first developed and shown to provide a tool for evaluating results of anchor load tests to determine the magnitude of expected elongation as a function of unbonded length. Next, a database of anchor load tests is used to back-calculate values of K for anchors with unbonded lengths in the range typically used in geotechnical applications (< 100 feet). These values of K are then used to calculate expected friction loss for anchors with high unbonded lengths (100 to 250 feet) to evaluate whether the 80 percent criterion is reasonable."

Jan 1, 2017

By John Lemke

Current practice for monitoring static pile load tests commonly consists of measuring load and displacement at the top of a pile. This is typically accomplished by monitoring dial gauge movements, line pressure of a hydraulic jacking system, and electronic load cells on occasion. While this testing approach provides useful information for one boundary condition (the top of the pile), a system that measures movement and/or strain along the entire length of the pile can provide additional useful data that can be used to refine pile design. Automated data acquisition systems provide the essential ingredient that can integrate these types of sophisticated instrumentation devices into a standard pile load test program in a cost effective way. This paper provides a general overview of pile testing instrumentation and describes a newly developed chain of instrumentation modules that can be embedded in a pile to gather additional testing information. The new system can measure forces and movements within the test pile synchronously with measurements at the pile top, and the direct application of this system to axial and lateral pile testing is illustrated. This is particularly relevant to the design of ACIP and drilled displacement piles since determination of the reinforcement cage length is important from the standpoint of both seismic design and foundation cost.

Jan 1, 2002

By Serhat Baycan, Mikias Yohannes

"Kuala Lumpur Karst is a complex limestone formation that is characterized by presence of cavities, solution channels, pinnacles and floaters. Basement excavations in such geological formations are usually challenging, mainly owing to the unpredictable rock head depths and potential for groundwater inflow. Any excavation support system should have adequate robustness and water tightness. Traditionally, Secant Bored Pile walls (SBP) with struts are the preferred option for karst ground. This paper discusses a cost effective and innovative alternative solution for a particular site – using Deep Soil Mixing (DSM) and using Contiguous Bored Piles (CBP) together with Ground Anchors (GA). The site, located around one of the busiest areas of Kuala Lumpur, is a 5,700 m2 commercial and residential development. A 16.0 m deep excavation was needed for four levels of basement and excavation support along the 275 m perimeter of the development. Within the site, the depth to rock head varied from 6 m to 19 m. The basis for each solution and conditions for its suitability are discussed in detail. Some design considerations and construction challenges are also presented. The performance of the two retention systems during excavation are presented, together with comparisons versus design predictions. Suggestions for future development are also given. Advantages of this approach compared to other traditional approaches are highlighted.1. INTRODUCTIONThe geology of Kuala Lumpur is among the most complicated and geotechnically challenging formations in South East Asia. The majority of the city falls into the Kuala Lumpur Limestone formation; which is a thick, highly-weathered and cavernous limestone. This formation is pure calcitic to dolomitic in composition, having infrequent schist and phyllite interbedding (Gobbett et al., 1973).The KL limestone has a highly karstic topography dotted with cavities, ravines, interconnected subterranean channels, pinnacles, overhangs, floaters and slump zones (Tan, 2006). This results in erratic bedrock profiles even within short distances. It is not uncommon to see a precipitous rock head incidence within short distances in the same site. In most parts of the City, the bedrock is typically encountered ranging from very shallow depths to about 30.0 m. The exception to this is at the heart of the City, where Kenny Hill formation prevails above the KL limestone. In such cases the limestone bedrock can be encountered much deeper. The erratic rock head profile and the highly karstic nature of the KL limestone makes it a geotechnical challenge requiring careful consideration of suitable engineering solutions.1.1 – Site DescriptionThe site, located in downtown Kuala Lumpur, is abutted by a busy street on the North. Before development, the site previously served as a car park. To the west an access road separates the site from an empty lot; while on the east, the lot is bounded by light weight residential and commercial buildings. On the south side, the site is bordered by a road that separates it from a prominent Shopping Mall in the City. A layout plan and an artist’s impression of the finished development is shown in Figure 1."

Jan 1, 1900