Search Documents

By Lucian Bogdan

On many occasions during construction and service life of the structure, it is crucial to know the load in post tensioning tendons and anchors. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive and the accuracy differs depending on the method used Dyna Force sensor uses the Elasto-magnetic technology (EM) and non destructive testing (NDT) to direct measure stress level in prestressed strands or bars installed on ground anchors or post tensioning tendons. Dyna Force sensor can be used to rapidly read the change in load during proof and performance tests and compare with the pressure gauge and during the life on the anchor to monitor existing lock-off load. It can be used also to determine the load along the bonded length of the anchor allowing the contractor to increase or decrease this length. The paper presents Dyna Force operating principle and some applications. In conclusion, the Elasto magnetic technology applied through Dyna Force is a new and easy to use approach to monitor anchor load during proof test and service life of the structure.

Jan 1, 2009

By David L. Borusiewicz, M. Suri Surendra

"Abstract Helical piles have been used as anchors and for supporting lightly loaded structures as a method of underpinning, etc in the past. Recently, helical piles are being used to support new structures because of their simple installation process using relatively light and mobile equipment. This paper presents the results of evaluation and design performed for the temporary support of existing piers during a bridge rehabilitation project.INTRODUCTIONThe helical screw foundation was invented and patented by Alexander Mitchell in England in 1833. He installed screw piles to support lighthouses in the tidal basins of England. Many applications in the earlier years in the USA were in North Carolina and in Florida to support lighthouses (in coastal plain deposits). A lighthouse of similar foundation design is still in use at Key Biscayne, Florida.In the USA, the helical piles were reintroduced as foundation elements for electrical transmission towers. Helical piles were also used for anchoring guys of self supported towers and as tie-backs for excavation support systems. Typically, helical piles are being used for supporting lightly loaded buildings and for underpinning buildings undergoing distress as a means of remediation. The helical piles are not commonly used in the transportation industry.HELICAL PILESHelical pile is a segmented deep foundation system with helical bearing plates welded to a central steel shaft. Load is transferred from the shaft to the soil through these bearing plates. Central steel shafts are available in either a square shaft (Type SS) or a round shaft (Type RS). The Type SS series are available in 38 mm to 57 mm square sizes. The Type RS series are available in 73 mm to 114 mm diameter sizes. Type SS-RS combinations are also available for compression applications in soil conditions where dense/hard soils must be penetrated with softer/loose soils above the bearing strata.The leading segment consists of a shaft with one or more helical plates that are welded to the shaft. The plates vary in diameter from 203 mm to 355.5 mm and have a thickness of 9.5 mm or 13.7 mm. Typically the plate diameter increases from the bottom of the shaft upward. A helical bearing plate or helix is one pitch of a screw thread. All helices, regardless of their diameter, have a standard 76 mm pitch. Being a true helical shape, the helices do not auger into the soil but rather screw into it with minimal soil disturbance. Helical plates are generally spaced a distance of two to three times the diameter of the plate directly below in order for them to function independently as individual bearing elements. A typical detail of helical pile is shown on Figure 1."

Jan 1, 2014

By Vivek Samu, Murthy Guddati

A new method called Effective Dispersion Analysis of Reflections (EDAR) was recently developed to effectively analyze the dispersive waves generated from lateral impact to piles. This paper presents the results of nondestructive length estimation of existing piles through EDAR. EDAR provides a new visualization method for analyzing wave reflections by transforming the response into the frequency domain thus eliminating the need to perform difficult peak picking in the time domain. In addition to being able to analyze dispersive waves, EDAR also incorporates the effects of radiation damping due to the surrounding soil leading to more accurate length estimates. Concrete filled steel tubes of different embedment depths were tested both in laboratory and field conditions. Length estimates obtained were within 10% error margins after careful analysis accounting for the presence of soil effects and effects from pile top reflection.

By W. H. Craig

Techniques have been developed for installing model piles into beds of soil under high sustained acceleration levels aboard a centrifuge. These piles have been subjected to static and/or cyclic lateral loading in order to assess their performance and provide a data base for assessment of various design techniques for laterally-loaded single piles. From measured bending moment profiles the so-called 'p-y' curves have been deduced using fifth order splines for curve fitting, followed by subsequent differentiation and integration. The results show some divergence from the predictions of the semi-empirical designs, but these latter are generally found to be acceptable.

Jan 1, 2010

By John P. Turner

The behavior of tieback retaining walls depends on many factors, including soil properties, groundwater conditions, construction sequence, spacing and stiffness of tiebacks and soldier piles, tieback loads, and others. The primary design considerations for tieback walls are 1) adequate stability and 2) limiting wall movements. Traditional design methods rely on apparent earth pressure diagrams and experience to predict the forces which must be supported by the tiebacks to provide adequate stability. The required soil properties depend upon whether the soil is sand, soft clay, or stiff clay. Design to limit wall movements is more difficult and the usual approach is to design the wall with an adequate factor of safety for stability and then evaluate wall movements during construction through the use of load tests on individual tiebacks and monitoring of wall movements by optical surveying, slope indicators, and extensometers. If excessive movements are likely to occur, it is often not known until construction is well underway. This approach is reflected in the fact that few tieback walls fail due to a lack of adequate stability, while most litigation involving tieback wall performance is related to excessive movements. Much progress has been made in recent years in methods for predicting the movement of all types of insitu retaining walls (Clough et al. 1989, Clough and O'Rourke 1990). These methods are based upon both experience and analytical methods. This paper reviews the methods currently available for evaluating both the stability and movements of tieback retaining walls. Case histories involving excavations constructed in the downtown Seattle area are used to evaluate the applicability of the available methods to Seattle conditions and to illustrate the importance of soil behavior in tieback wall performance.

Jan 1, 1990

By Davide Grassi, Joel Joaquin Cortez, Giovanni Spagnoli, Nick Chittenden

Grouting is a technique used to improve the engineering properties of soils and rocks. Grouting techniques are classified under different criteria: injection method used, type of grout material injected, typical application, and the sequence of construction. The best-known criterion is the mode of entrance or admission of grout into the soil or rock. It is possible to identify therefore several grouting techniques: compaction, fracture, jet/mixing and permeation. The function of penetration grouting is to reduce the permeability of the soil or rock and/or increase the strength and density. In order to avoid displacement, permeation grouting shall be carried out at carefully controlled pressures and flow rates, using appropriate grouts. Colloidal silica is an innovative binder which has low viscosity (about 5 m·Pas), it is not toxic (pH lower than 9) and it is workable between +5°C and +45°C. This paper presents several case histories: a consolidation job related to the installation of a new sewer in North Italy in cohesionless soils, water stopping injection in a weathered granitic bedrock in California, permeation works in the US in sandy soils to improve excavation and the installation of sheet piles in the UAE. Results show that the colloidal silica an innovative and robust technology to perform grouting in very fine soils where conventional binders or micro-fine cements cannot penetrate.

May 1, 2022

By Dhanaji S. Chavan, Thallak G. Sitharam

"It is well known that sites comprising of saturated loose sand undergoes large deformations, due to liquefaction, during seismic shaking. To cope with this, different mitigation techniques such as vibroflotation, deep dynamic compaction, compaction grouting, deep soil mixing etc. have been used in practice. However, as all these methods are costly, a new mitigation technique is required. Air injection has emerged as a new mitigation technique in which air is injected into the saturated loose sand. The introduced air makes the pore fluid mixture compressible and results into decrease in the generation of excess pore water pressure during seismic shaking. This paper reviews the laboratory and field studies performed to investigate the effect of air injection on liquefaction resistance. In addition to this, previous research in the direction of desaturation has evolved different techniques to generate gas in saturated sand. These techniques have also been discussed in the present paper. All the field and laboratory studies have shown that even a slight decrease in the degree of saturation increases the liquefaction resistance significantly.Keywords: desaturation, air injection, liquefaction resistance, pore pressureINTRODUCTIONEarthquake events in the past, caused liquefaction of loose saturated sands at many sites in the world. The consequence of liquefaction varied from small deformations to catastrophic failures such as flow slides, lateral spreading, sand boiling etc. (Kramer, 1996). To reduce the liquefaction potential of such soils, different mitigation techniques have emerged across the world. Some of the most widely used mitigation techniques are vibroflotation, deep dynamic compaction, compaction grouting and deep soil mixing (Idriss and Boulanger, 2008).Yoshimi et al. (1989) found that the liquefaction resistance of partially saturated sand is significantly higher than that of saturated loose sand. Further, Pietruszczak et al. (2003) proposed desaturation of the saturated loose sand as a new liquefaction mitigation technique. It is observed that the liquefaction resistance of sandy soil is enhanced significantly owing to the desaturation caused during construction of sand compaction piles (Ishihara et al. 2003). Over past few years research is being carried out on desaturation of sandy soil and its liquefaction resistance ( Ishihara et al. 2003; Okamura and Soga 2006; Yegian et al. 2006; Yegian et al. 2007; Takemura et al. 2009; Eseller-bayat et al. 2013; He et al. 2013; Marasini and Okamura 2015; Zeybek and Madabhushi 2016). As a result of this, different techniques of desaturation have also emerged. Different studies conducted in this direction and their outcome has been discussed in the section to follow."

Jan 1, 2017

By Makoto Kimura

Failure tests on laterally loaded single and pile group are analyzed with a 3-dimensional elasto-plastic finite element program. In the analysis, the mechanical behavior of the ground is supposed to be elasto-perfect plastic with Drucker-Prager's yielding criterion. The nonlinearity of the piles is simulated by assuming a hyperbolic relation between the bending moment and the curvature of the piles. The influence of the axial stress on the cast-in-place concrete piles is also considered in the numerical analysis. It is found that the mechanical behavior of the piles subjected to lateral loading, such as the load-displacement relation up to an ultimately large deformation, and the distribution of bending moment in the pile group can be well simulated.

Jan 1, 1996

By James Weaver

During the past 16 years, the authors have successfully used high-capacity rock anchors installed inside open-ended pipe piles, driven to bedrock, to provide uplift and overturning resistance for various structures including piers, bridges, power plant components and commercial buildings. These systems were ultimately used on the projects due to a combination of high uplift forces or overturning moments on the structures and the relatively poor subsurface conditions present at the sites. Other, foundation systems such as rock-socketed drilled shafts and spin fin piles were considered but were found to be economically prohibitive or not technically feasible.

Jan 1, 2011

By Alain E. Holeyman

After scoping out the objectives of this general report, the report reviews the three assigned main themes addressed by the papers submitted to the session: pile monitoring, testing, and data processing. It focuses on later developments and on issues requiring clarification, thereby identifying topics for potential discussion. Pile Monitoring does not bring much novelty, except for the integration of IT on construction sites. As far as testing, new developments focus on internal pile loading procedures while more confidence is being gained with dynamic and kinematic load tests. Significant advances are noted in the interpretation of data, where variability of results are coped with, loading rate effects are being better addressed, and more routine use of Finite element analyses are observed. Several many older problems remain while new issues emerge from more recent technologies and approaches.

Jan 1, 2006

By Michael J. Atwood

Many buildings in Boston are founded on untreated wood piles, which can deteriorate and lose their structural capacity if groundwater levels are lowered below the tops of the piles, exposing the wood to air in the unsaturated soils that surround the piles. The problem of wood pile deterioration due to lowered groundwater levels in Boston first became evident in 1929 following discovery of rotten piles beneath walls of the Boston Public Library building. Repairs to reconstruct the library building?s wood pile foundations were made in 1930 using pit underpinning methods. Today, more than 80 years later, the subsurface conditions beneath several of Boston?s historic neighborhood areas continue to be plagued with low groundwater levels - regrettably resulting in ongoing deterioration to the wood piles that support some of Boston?s oldest and most beautiful buildings. Pit underpinning is still recognized as the preferred approach to repair wood piles and restore uniform foundation support beneath the impacted buildings. This paper provides a brief historical review of the land filling in Boston through the early 1900s that led to the use of wood piles as building foundations. Also discussed is the impact that groundwater level can have on the long term performance of wood pile foundations and the pit underpinning procedures used to reconstruct decayed wood pile foundations in 1930 beneath the Boston Public Library, and today beneath some of Boston?s oldest buildings. Also included are discussions on engineering controls and permitting requirements that help ensure safety and protection to the workers and buildings during underpinning, and some procedures being used to supplement and improve the loading capacity of the reconstructed foundations and facilitate construction of new useable below-grade space.

Jan 1, 2011

By P. Seethalakshmi, Yatakuri Yaswanth Naidu

The use of a single pile, group of piles with pile cap, piled raft foundation system, etc., are prevalent in transferring the superstructure load from the soft soil layers to the firm underground layers to reduce the settlement and improve the bearing capacity. The recent development of disconnected piled raft foundation has gained greater importance in improving the load transfer mechanism among the pile, raft, and subsoil by reducing the vulnerability of the greatest axial force on the pile head which leads to pile failure. The present study aims at analyzing the performance of unreinforced and Geogrid reinforced disconnected piled raft foundations under vertical loading using the commercially available finite element software PLAXIS-3D. A parametric study was conducted on unreinforced and reinforced disconnected piled raft foundations to explore the effect of varying pile stiffness as well as the inclusion of Geogrid layer on the load vs settlement, the load sharing ratio of piles and raft, and the distribution of axial load and bending moment along the length of the pile. The Mohr-Coulomb model was used for the granular cushion layer while the Modified Cam Clay model was used for soft clay underlain the sand layer. Raft and piles were assumed to be rigid and linear elastic. The results showed that axial force taken by piles with higher stiffness was maximum while settlement at the bottom tip of the pile with higher stiffness was maximum in both reinforced as well as unreinforced disconnected piled raft systems.

Sep 1, 2022

By Robert Jakiel

The following paper is being presented to provide a basic understanding of the equipment and procedures used in multi-auger deep soil mixing as part of the program for the Deep Foundations Institute (DFI) Deep Soil Mix Seminar. The paper is written as a summary of the author's experience using multi-auger deep soil mixing equipment while working with SMW Seiko, Inc. on several east coast projects in the United States, particularly the soil-cement mixing for the soil stabilization of the Fort Point Channel area in Boston, Massachusetts, one of the largest and most difficult soil mixing projects completed thus far in the United States. The summary provides a brief summary and insight into some of the operational aspects of the equipment and procedures, and some of the important considerations when using multi-auger deep soil mixing. This paper is intended for use by both the contractor and the designer involved in selecting appropriate soil mixing equipment and procedures for various types of soils, depths or applications, or for a better understanding of the operational aspects, potential benefits, and impacts that the performance criteria may have on the operational capabilities of the soil mix equipment, when specifying multi-auger soil mixing for a particular project. Prior to reading this article it is important to become more familiar with the various acronyms and terminology used in soil mixing technology. A Definitions section has been provided at the end of the paper that will help the reader become more familiar with some of the terms used throughout this paper.

Jan 1, 2001

By David S. Graham, Joseph D. Bailey, Paul J. Axtell, Michael K. Muchard

"Two instrumented test piles were simultaneously subjected to a static lateral load test by jacking the piles apart. One of the piles was loaded in axial compression via kentledge during the lateral load test. Both piles were constructed in an identical manner. These piles were constructed and tested as part of a construction-phase load test program for a floodwall improvement project along the Missouri River in Kansas City, Kansas. Details of the subsurface conditions, drilled pile construction, instrumentation, and load testing procedures are described. Data collected during testing of the piles are presented and compared. Potential effects of the axial compressive load related to observed differences in pile lateral response are discussed.INTRODUCTIONTwo instrumented test piles were simultaneously subjected to a static lateral load with one of the piles also subject to a combined axial load during testing. The load test program was part of a floodwall improvement project in Kansas City, Kansas. Known as the BPU floodwall, the floodwall runs along the south bank of the Missouri River at a Kansas City Board of Public Utilities power generation and water treatment facility. The project location is shown in Fig. 1.Drilled, 2-ft (610-mm) diameter piles were designated by the designer, the U.S. Army Corps of Engineers (COE), as the foundation type for supporting extended floodwall footings. The drilled piles are fully cased, cast-in-place concrete, reinforced with a steel 12x74 (310x110) H-pile. In order to test soil lateral response and pile structural response under combined loading, the COE required that both a lateral test and combined lateral and axial test pile be constructed and tested. In order to most efficiently test both piles and to allow for simpler comparison, the two piles were simultaneously laterally loaded by jacking the piles apart, applying a maximum lateral load of 195 kips (867 kN). A constant axial load was applied to the combined test pile by kentledge prior to lateral loading and was maintained for the duration of the lateral load test. The total weight of the kentledge was 61.5 kips (274 kN). Fig. 2 shows the test setup."

Jan 1, 2017

By D. Millgard

Dennis Millgard introduced the Session by hoping that participants to the Conference would also share their piling problems. He then invited the first speaker to present his paper. Paper 5.1. Pat Kelleher commenced by saying that he belonged to a one hundred year old firm that had experience in the New York Harbour area. They were often asked to assess the integrity of many waterside structures such as piers, walls, and docks which were deteriorating whilst still in use. The earliest structures, built in the 1800's, were on timber piles. These have now changed to Steel H and tube piles and concrete piles. Usually they were called in when the structure was showing signs of distress, or had reached the end of its life but could not be closed. In particular, they had found that marine borers had returned to New York Harbour because of the improved quality of the water. There is now a far greater incidence of attack on the timber piles than when the water was polluted. Repair is usually carried out by encapsulating the pile within the tidal range of about -2ft to +8ft (-0.6 to +2.4m). Reinforced concrete forms, reinforced fibre jackets, or nylon bags are used. Reinforced fibre jackets are used with a protective coat on the pile, while nylon bags prove the cheapest method.

Jan 1, 1991

By Fathi Abdrabbo

Open caissons are used for many geotechnical engineering applications. Open caissons may be used as deep foundation elements bypassing weak soils to tip in firm deeper strata, and in rivers and maritime construction to reduce the risk of scour. Open caissons are also used for collecting sewage water through gravity sewer pipe networks or from sewer force mains. In such applications, the design and construction of open caissons require a detailed soil investigation program. In this way, the design and construction plan of an open caisson can be developed with full knowledge of the prevailing subsoil conditions. The engineering and construction techniques are key factors to achieve functional caissons. Based on close observations during construction stages, the current study presents some challenges that were encountered during the construction of two open caissons of internal diameters 20 m and 10 m (65.6 ft and 32.8 ft). This paper describes the procedure followed to alleviate the construction difficulties encountered. Site exploration program and control measures required to satisfy design and construction requirements are crucial aspects. Sinking of open caissons in dense or very dense sands is risky. Incorrect sinking of open caissons may cause extra cost, delay in construction, and harm to nearby structures. Air/water jetting near the cutting edge of an open caisson, outside slurry trench, and/or inside open trench may be used to drive an open caisson downward. Unsymmetrical work around an open caisson may lead to tilting of the caisson. If this occurs, the tilt should be immediately corrected before resuming the sinking process. Improper cleaning of fine materials on the caisson?s excavation bed, and/or inappropriate pouring of underwater concrete may result in a defective concrete seal. The paper contains a series of practical guidelines to assist those intending to use open caissons, and shares good caisson sinking practice with practitioners. Finally, the study aims to understand the difficulties encountered and to anticipate future problems.

Jan 1, 2012

By Richard J. Hartman

This presentation identifies some of the more common problems associated with cofferdam construction. After the various problems are identified, they are briefly explained and possible solutions and preventive measures are noted. Photographic slides used during the seminar illustrate the conditions. This discussion is limited to cofferdams which are braced structures excavated inside to allow access for construction. The common procedure is to drive sheet piling and then alternatively install bracing and excavate. They can be located either on land or in water. Loads are applied by soil, water, surcharge pres-sure, eccentricities, and impact loads. The loads are resisted by the sheet piling, the bracing, and the soil below the bottom of the excavation; each of these three components must be capable of resisting the applied loads.

Jan 1, 1987

By Shoji Higashi, Nobuhiro Honda, Takeo Asanuma, Tatsuo Nagatsu, Masaki Kitazume, Sachihiko Tokunaga, Shigeru Kubo, Hidenori Takahashi, Tsuneyasu Onishi, Yoshiyuki Morikawa

"Various kinds of civil engineering structures and facilities were seriously damaged in the earthquake in Tohoku and Kanto regions of Japan on 11 March 2011 due to the greatness of its magnitude. In contrast, many structures resisted the large seismic force having been reinforced by the CDM (Cement Deep Mixing) method, which is often used for increasing the bearing capacity of ground and improving seismic performance. This paper summarizes the field survey undertaken to investigate damage to structures and facilities reinforced by the CDM method. Several prefectures and metropolitan areas were selected for the survey, based on the occurrence of strong seismic motions. A total of 847 structures and facilities were studied, in the survey using a questionnaire, which mainly inquired about the appearance of structures and facilities. Of the respondents to the questionnaire, 789 replied that there were no seriously damaged structures. The paper presents the damaged and non-damaged sites of CDM-technique sites and non-CDM-techniques sites. It can be concluded from the field survey that the CDM Method demonstrates high efficacy and durability against a strong seismic motions.INTRODUCTIONDuring the afternoon of 11 March, 2011, a huge magnitude-9.0 Mw (Category 9.0 on the Richter scale) earthquake occurred about 25 kilometers below the Pacific Ocean’s surface off the coast of Tohoku. This massive earthquake, now called the 2011 Off the Pacific Coast of Tohoku Earthquake was the largest earthquake ever observed in Japan. The seismic intensity of this earthquake was measured 7, the maximum on the Japanese intensity scale, as observed 7 in northern Miyagi Prefecture. The earthquake caused severe damage over a wide area from Tohoku to Kanto, and triggered large tsunamis that struck the Pacific coast of Hokkaido, Tohoku, and Kanto. The number of missing and fatalities caused by this earthquake exceeded 18,000 persons, making this an unparalleled earthquake disaster with a cost-in-life toll not experienced by Japan in recent years. Because of the scale of its seismic motions, the earthquake damaged facilities and structures of many kinds. In the years prior to this earthquake, the CDM method was used extensively to increase the bearing capacity of the ground as an anti-seismic countermeasure and to prevent liquefaction. Immediately after the earthquake, the CDM Association visually surveyed the state of damage to about 800 facilities in the Tohoku and Kanto regions where a seismic intensity of 5 or higher was observed. This report summarizes the survey of damage to facilities and structures constructed applying the CDM method in order to confirm the durability and performance of the method against seismic motions."

Jan 1, 2015

By Annika Gram, Teddy Johansson, Lutfi Ay

Micropiles transfer tension or compression forces as well as cyclic loads into the ground via skin friction. The Self Drilling Micropiles (SDM) can be utilized for permanent applications. The hollow bar simultaneously acts, as drilling rod, injection tube and reinforcement for the micropile. The SDM system can be used in any type of soil, including unstable soils, without the need for temporary casing. Injecting a cement grout through the hollow steel tendon ensures that the borehole is filled from the bottom to the top. The system is fast, simple, and flexible. The installation minimises noise, vibration, and spoil. There are many potential applications, including foundations, underpinning, resisting uplift, dynamic/cyclic load applications and geothermal installations. The SDM technology were introduced to India first time in the Indian history and utilised in the 4G and 5G network projects. The SDM challenge the traditional cast-in-situ piles in the 4G project and raft foundations in the 5G project. Utilisations of the tensile and the compressive strength capacity of SDM with smart solutions results in noticeably big costs, 17-38 % depending on the soil conditions and time savings. The cost of the SDM solutions was about 40% less than the cast-in-situ piles and raft foundations in an ongoing 5G project. The SDM were used successfully in the liquefiable soil types as well.

Nov 1, 2022

By Richard E. Sylwester

Evaluating surface and subsurface conditions for marine foundations (bridges, causeways, terminals, etc.) is often done with a limited amount of data. Subsurface information for these projects is primarily acquired using traditional methods, such as boreholes, test pits or divers, which tend to be expensive and limited in the area of coverage. A number of geophysical methods, including precision bathymetry, sidescan sonar, and seismic reflection or subbottom profiling are extremely cost-effective and obtain significantly more data than can be acquired using traditional intrusive methods. These geophysical methods provide detailed surface images and continuous profiles of the subsurface stratigraphy. This information can be invaluable for selecting the best location for geotechnical boreholes and to map potential geohazards such as submarine slides and filled or open scour holes. Offshore investigations conducted for a proposed highway bridge (Knik Arm Bridge, Cook Inlet, AK), the retrofit of two existing bridge (Antioch and Dumbarton Bridges, CA) and a proposed cruise ship terminal (Ketchikan, AK) used a combination of geophysical methods to map water depth, detect and map debris on the seabed, map the thickness of unconsolidated sediment, determine the depth to bedrock and identify potential geohazards such as scour holes. The results of the geophysical investigations will be used to select locations for obtaining geotechnical borings, to extrapolate geologic information between existing or proposed boreholes, evaluate the potential depth of scour and design a pile support pier. Geotechnical engineers, offshore contractors and bridge designers are realizing the importance of the early use of offshore geophysics for (i) site characterization, (ii) to reduce the uncertainty of geotechnical conditions thus avoiding designs that may be overly conservative and thus more expensive and (iii) to assist in selecting locations for geotechnical borings.

May 11, 2007