Search Documents

By Dan Brown

Improvements in construction equipment and techniques in recent years have made possible the use of drilled shaft foundations in diameters and lengths not previously considered practical or feasible. Many highway bridge and other structures are now routinely founded on drilled shafts which are 2.5 m to 3.0 m (8 to 12 feet) in diameter and extending over 60 m (200 feet) in depth below grade. There are unique challenges associated with constructing such large and deep cast-in-place foundations and engineers should be aware of the special needs associated with site investigation, construction specifications, material requirements, and quality assurance. This paper outlines a number of special considerations for these foundations, along with strategies that may be employed to improve the reliability and quality of large drilled shaft foundations.

Jan 1, 2008

By Hayel M. El-Naggar, Marawan M. Shahien

"Large capacity piles are important type of foundation elements that are needed in case of high column loads such as in tall buildings with large span between columns. In many projects, especially if the designer uses the concept of one pile supporting one column (Hamza, 2003a & b). The axial capacity of the large bored deep foundations can be further increased by grouting the shaft skin and the base of the pile. The increase in the capacity of the piles due to grouting can be tremendous. Thus grouting appears as an ideal solution for achieving more reliable foundation and greater savings (Littlechild et al., 2000). A data base of pile load tests of instrumented grouted piles is under development in a major study aiming to propose a simple method to estimate the axial capacity of large bored grouted piles. The data base include pile load tests from projects constructed in Egypt and abroad. The main goal of this paper is to analyze pile load test(s) from one project. The tested deep foundations included 1.2 m diameter and 1.5 m diameter piles and a barrette of size 1.0mx2.8m. The instrumentation of the tested piles and barrette allowed for the separation of skin friction and base contributions to the axial load. Further, the contribution of the skin friction of every layer along the pile shaft could be identified. The results of the analysis clarified how base and shaft grouting increased the axial capacity of the pile and decreased the settlements for certain load level compared to conventional un-grouted piles installed under similar conditions.INTRODUCTIONIn recent years, significant research has been carried out to develop new techniques which are suitable to withstand problems in major projects such as high applied loads in high rise building, large spans structures projects and structures designed using the concept one pile supporting one column (Hamza, 2003a & b). Base and shaft grouting of piles are one of these new techniques which aim at decreasing the settlements and increasing the capacity of the pile under axial load that became major requirements in large projects (Stocker, 1983; Mullins et al., 2001; and Hamza, 2015).Base grouting consists of injection grout under pressure at the base of the pile after the concrete is sufficiently hard. Field evidences showed that the ultimate end bearing of base-grouted piles could be as high as 1.5 that of non-base-grouted bored piles (Suckling and Eager, 2001). Further, field evidences was provided by Shahien and El-Naggar (2015) that showed an increase in end bearing resistance due to base grouting reached to 2 to 3 times that of non-base-grouted bored pile. On the other hand, shaft-grouting causes increase in the soil density in the zone which had been disturbed by the pile construction and thereby improves the shaft resistance of the pile. Field measurements by Gouvenot and Gabaix (1975), Stocker (1983), Robson and Wahby (1994), Troughton and Stocker (1996), Byrne et al. (1998), Joer and Randolph (1998), Hamza and Leoni (1998), Littlechild et al. (2000), Hamza and Ibrahim (2002), Hamza (2003 a&b), Hamza (2015) and Shahien and El-Naggar (2015) showed that the shaft resistance of grouted piles could be nearly 1.5 to 5 times that of non-grouted piles."

Jan 1, 2017

By Lu Yitan, Frances Badelow, Manish Tiwari

"Large ‘design and construct’ projects often present significant geotechnical risks. However, these also present significant opportunities for value engineering in design. These opportunities can be realised through systematic site investigation and close collaboration with the Contractor to dovetail the design solutions to suit construction methods. This paper presents a case study of a large infrastructure project in Singapore which involved design optimization of an earth retention system for a deep excavation in a constrained urban environment. The project also required installation of over one thousand bored piles in highly variable ground conditions - identified as a key risk. Systematic site investigation was undertaken to develop a reliable ground model. A detailed value engineering exercise identified opportunities for design optimization by changing the retention systems and construction sequence in some segments. An innovative low cost ground improvement method was used in some areas to reduce the forces on the retention system. An extensive instrumentation and monitoring plan was implemented for verification of design and to mitigate the remaining risks. This paper includes the lessons learnt on this challenging project, which are relevant to a wide range of construction projects.INTRODUCTIONSingapore has been rapidly expanding its underground Mass Rapid Transit (MRT) network over the past two decades. The Thomson-East Coast Line (TEL) forms part of this expansion and is 43 km long and fully underground comprising 31 stations. This paper describes the value engineering and design optimizations undertaken during detailed design of the earth retaining and support structures (ERSS) for one of the underground stations along TEL. The station, currently under construction, is up to 24m deep and 350m long. The edge of the station excavation is less than 10m away from the existing MRTviaduct. The proposed station is surrounded by high-rise residential and commercial structures, somewithin 2m of the excavation. Land Transport Authority (LTA) of Singapore imposes stringent technical and contractual requirements on MRT construction works to ensure high quality and safety standards. These include minimum requirements for embedment of retaining walls, groundwater control, additional site investigation, instrumentation and monitoring, and compliance to LTA’s Civil Design Criteria (CDC). Any deviations from the minimum requirements can only be approved by LTA after detailed calculations, analysis and field testing are completed and additional monitoring and control measures are proposed."

Jan 1, 1900

By Murad Y. Abu-Farsakh, Md Habibur Rahman

The properties of all natural soil deposits are highly variable, and they are rarely homogeneous. Cone penetration tests (CPT) were used to assess the site variability, which was then incorporated into the Load and Resistance Factor Design (LRFD) of pile foundations. Data from six project sites with multiple CPT tests conducted at various locations were collected for this research. The semi-variogram was used to assess the spatial variability of CPT data (corrected tip resistance, qt) for each location. For each location, the coefficient of variation due to spatial variability (COVR,spatial) was calculated. From COVR,spatial and COVR,method, the total coefficient of variation (COVR,total) for each site was calculated, which was then used to calibrate the resistance factors (ϕspatial, ϕtotal) for use in LRFD pile foundation design. The findings of this study demonstrated the importance of using site variability in LRFD pile design. For sites with lower site variability than the design method (i.e., COVR, spatial < COVR, method), the value of the COVR, total will be decreased, and hence the resistance factors (ϕspatial or ϕtotal) will be increased (credit), and vice versa.

Sep 8, 2021

By Luo Yang

It has been known that after initial pile driving, pile capacity gain over time (set-up) could constitute a significant portion of the total pile capacity. In the past, there has been very little guidance for incorporating pile set-up capacity in design. This may be due to large uncertainties involved in predicting the pile set-up. A comprehensive statistical database is developed to describe the increase of pile axial capacity with time, known as set-up, when piles are driven into sand. Based on the collected pile testing data, pile set-up is significant and continues to develop for a long time after pile installation. The statistical database shows that a lognormal distribution can be used to describe the probabilistic characteristics of the predicted set-up capacity using Skov and Denver?s equation. The main objective of this paper is to incorporate the set-up effect into a reliability-based Load and Resistance Factor Design (LRFD) of driven piles in sand. A First Order Reliability Method (FORM) is used to derive separate resistance factors that would account for different degrees of uncertainties associated with the measured short-term capacity and the predicted set-up capacity from the proposed semi-empirical equations. The incorporation of set-up effects in the LRFD helps improve the prediction of the total capacity of driven piles, resulting in more economical design. A practical design procedure within LRFD framework to incorporate the pile set-up effect is outlined at the end of the paper.

Jan 1, 2006

By Fredrik Sarvell, Leo-Ville Miettinen, Veli-Matti Uotinen

"Abstract The continued concentration of building activities in cramped areas of city centres means more underground construction and facilities. Demand to minimize execution time and any kind of disturbance to business, general traffic, people and nearby technical structures is increasing. To answer these challenges foundation business has to develop schedule-wise and technically reliable deep excavation and foundation solutions in vulnerable surroundings and challenging soil conditions.Drilled pipe pile wall – RD-pile wall – is a combination of Ruukki drilled steel pipe piles and interlocking sections. Individual RD piles, typical diameters between 219 mm to 610 mm, are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole hammer (DTH) using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings.RD-pile walls have been used as permanent and temporary retaining walls for different kinds of demanding excavations and structures, such as bridge foundation, as quay wall and as sealing structure in rehabilitation of an existing dam. Rigidity and watertightness of the lower end of the RDpile wall is being researched as well as fire design issues examined. One of the most fascinating RDpile wall solution is to utilize the wall as a permanent underground basement wall. Reliable and rigid connection to bedrock decreases the bending moment and deflection of the wall and good fire resistance in addition to large variety of pile dimensions and steel grades gives possibilities to design and execute a cost-efficient basement wall and foundations without temporary retaining wall works. 1. IntroductionIn northern Scandinavian soil conditions, installation of sheet pile walls, or even secant pile walls, is often problematic due to the existence of hard and large boulders in the overburden, and especially when the retaining wall structure should penetrate to or into the hard bedrock. On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid-1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers)."

Jan 1, 2014

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan, Joseph Toth

The difficulty in material characterization and the erratic response of cemented soil layers, such as caliche in the Las Vegas valley, creates challenges for practicing engineers to reliably predict the response of deep foundations. The focus of this paper is the numerical prediction of axial response in drilled shaft foundations, which are commonly used in infrastructure projects (i.e., bridges and tall buildings) in Las Vegas, NV. The prevalence of hard caliche layers with variation in the degree of cementation add to the complication in numerical modeling. In this study, the applicability of two existing t-z models, developed for Florida limestone and soft rock, was evaluated based on numerical simulations of three bi-directional load tests conducted at caliche-dominant sites. The corresponding top-down load tests were also simulated for further assessment. A MATLAB-based finite-difference program, NVShaft, has been used to implement the mentioned t-z models in axial load analysis. Complexity originating from drilled shaft construction and the interaction with caliche during one axial load test resulted in a stiffer predicted response compared to measure data. For the other two load tests, both t-z models produced comparable load-displacement responses. It was observed that the t-z model for Florida limestone predicted relatively stiffer responses and higher drilled shaft capacity.

Sep 8, 2021

By Timothy C. Siegel

This report presents the results of a synthesis on the design and analysis of ground improvement for liquefaction mitigation. The synthesis included an industry survey concerning the practice of ground improvement for liquefaction mitigation. Participation in the survey was solicited by advertisements in several trade magazines and by e-mail for the DFI membership. The survey participants numbered 150. Their professional roles include consulting engineers, specialty contractors, design engineers, government engineers, and academicians. They represent a variety of geographical areas including North/Central/South America, United Kingdom, Middle East, Caribbean, Hawaii, Japan, India, Egypt, France, Australia and New Zealand. Upon completion of the survey, several professionals in the field of liquefaction and ground improvement were interviewed for them to elaborate on the survey results. The interviews are included in the Appendix of this report. Financial support for the project was provided by DFI and Dan Brown and Associates PC. The concept of the liquefaction mitigation synthesis was developed by DFI?s Ground Improvement Committee in recognition that: (a) The results of recent research and post-earthquake reconnaissance have challenged previously longheld beliefs about liquefaction and associated mitigation techniques, and; (b) The DFI membership and the engineering/construction industry are interested to know if and how engineers and designers are subsequently adjusting their practice in consideration of recent research and post-earthquake reconnaissance. For more detailed information on recent research and post-earthquake reconnaissance, presentations are available from the State-of-the-Art Forum: Liquefaction Consequences and Mitigation that was held in St. Louis in 2012. A commentary of the state-of-practice in ground improvement for liquefaction mitigation (prepared by DFI?s Ground Improvement Committee) is included in this issue of the DFI Journal. The author would like to thank the participants of the survey and especially Mr. Mike Jeffries, Dr. Les Youd, and Dr. Ikuo Towhata for their willingness to share their expertise in interviews. The author also acknowledges Mary Ellen Bruce of DFI, Billy Camp of S&ME, Inc., and Marty Taube of DGI Menard (and Chair of DFI?s Ground Improvement Committee) for their signifi cant contributions.

Aug 1, 2013

By Richard Berry

The spacing of grout injections is typically about 2 to 2 V½ meters if the purpose of the grouting is densification of the in-situ soils. Hole spacing will vary with the in-situ soil properties and the grout injection rate; faster rates requiring closer hole spacing.

Feb 10, 2003

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

A Smart Cell is a closed-type tip post-grouting device that is attached to the bottom of the steel reinforcement cage of a drilled shaft and is used to enhance performance and to reduce uncertainty thereof. Control of the grout is maintained within the device during injection and a uniform stress is imparted across entire base area simultaneously, inducing a pre-mobilization load into the shaft as well as the soil. This paper describes the construction and tip post-grouting of drilled shafts from two bridge projects in the Santa Cruz, Bolivia region along the Paraí River. During the grouting process at each project site, there were noticeable differences in the grouting pressures achieved and responses observed, even within short distances between shafts. For this project, the greater benefit of using the Smart Cells was the reduction of risk and uncertainty of performance due to the highly variable soil conditions. Ultimately, since the response of each shaft was observed during grouting and because a “minimum” value of shaft resistance (i.e., pre-mobilization of load) was measured, there is a greater reliability with the anticipated performance of the shafts when axial loading is eventually applied.

By Rae Mackay, Kaveh Ranjbar Pouya, Ali Tolooiyan

"A major part of Melbourne’s central business district is underlain by a very soft silty clay deposit known as Coode Island Silt (CIS). Due to the low strength of CIS, most construction in the region is based on pile foundation systems. Traditionally, the design of pile foundations is mostly based on empirical and analytical methods. However, numerical methods such as Finite Element Methods (FEM) can be utilised for more accurate estimation of the bearing capacity and deformation of pile foundation systems, especially in complex loading scenarios. Unfortunately, no systematic effort is made yet to calibrate a realistic nonlinear constitutive model to describe the geomechanical behaviour of CIS in a numerically based solution. Among the nonlinear constitutive models, the Hardening Soil (HS) model is an advanced hyperbolic model which accounts for the nonlinearity of stress-strain relationship as well as the stress dependency of the soil stiffness. In this study, the HS model is calibrated based on laboratory tests performed on CIS. Also, to validate the accuracy of the calibration, the wellknown cavity expansion theory is employed to model the CPT cone tip resistance (qc) in CIS, and results are compared against the measured CPT qc profile at the field.INTRODUCTIONA large percentage of world’s coastal areas are covered with soft marine clay deposits. Having very low shear strength and high compressibility, the alluvial deposits are known as one of the most problematic soil layers for the design and construction of infrastructure facilities. A major part of Melbourne’s central business district is underlain by a very soft silty clay deposit known as Coode Island Silt (CIS). Basically, there are two main solutions for construction in such weak soil conditions. One is the use of pile foundations transferring the applied load to deeper and stronger soil layers, and the second one is to employ ground improvement techniques such as using deep soil mixing columns to improve the bearing capacity of the soil. In both cases, a practical geotechnical design should incorporate both stability analysis and deformation analysis to achieve a cost-effective and reliable solution. Most of the classic solutions for stability analyses such as limit equilibrium analysis disregard the stress-strain relationship of the soil for the sake of the simplicity (Chen, 2007; Sokoloviskii, 1965). In a similar simple approach, most of the past studies of deformation analysis have been established on the basis of linear elasticity. However, it is well recognised that the soil stress-strain behaviour is highly nonlinear even at very small strains (Burland, 1989). Hence, for a precise deformation analysis of the foundation of important geotechnical structures, the application of advanced nonlinear constitutive models is extremely beneficial. Precise deformation analysis is essential as geotechnical designers have to predict the displacement of geotechnical structure and the adjacent soil as well as the induced displacement and forces to adjacent structures. This issue is more highlighted recently in the analysis, and design of highly important infrastructures as geotechnical engineers are facing new challenges in the analysis and design of infrastructures in congested areas. Rapid population growth, especially in the major cities all around the world necessitates the design and construction of more integrated infrastructure facilities. Consequently, geotechnical engineers should employ more advanced design approaches to address the new challenges in geotechnical engineering practice. Complicated geometries, different loading scenarios and the application of nonlinear deformation models which is believed to be essential for a precise deformation analysis, necessitate the application of numerical methods to satisfy most of the design requirements."

Jan 1, 1900

By Sina Z. Yekta, Zhangwei Ning, Pierre Frappin

This paper describes a DC (direct current) electrical resistivity method, which uses the contrasts in resistivity measurements to estimate the diameter of jet grouted columns as soon as they have been completed, with varying depth and water table, and without excavation. The measurement procedure is illustrated by several examples of application sites, including the Grand Paris tunneling works during the last 3 years where the method was systematically recommended in quality control for jet grouting works.

Sep 8, 2021

By John C. Ryan

The Emeca Pile Splice, an innovative mechanical prestressed concrete pile splice, is the first robotically welded splice to be fabricated in the United States. An analytical and experimental study was conducted to establish the capacity of the standard splice for 12-in. and 14-in. square piles. The study illustrates compliance of the splice with International Building Code (2006) requirements. A case study for a large petroleum tank foundation project in Port Canaveral, FL is presented, demonstrating the efficiency achieved through use of spliced-piles. For the case-study project, single-piece 18-in.-square, 100-ft-long piles were replaced with 12-in.-square, two-piece, spliced piles. As a result, a significant reduction of material, labor, handling, and equipment was documented for the project. Savings realized on the installed pile cost was estimated to be in excess of 30% by the owner.

Jan 1, 2010

By Marcel Bielefeld, Joost Bakker, Rob van Dorp

Pile load testing can be performed by a static, rapid or high strain dynamic (generally designated as dynamic) testing method. The static load test is often considered the “gold standard” of testing with the other methods merely ‘alternatives’. However, the rapid load test, as a quasi-static test, has all the positive elements of the static alternative: the direct measurement of loads and displacements. Moreover as stress wave phenomena have no influence, the interpretation of rapid load test results is more straightforward than that of dynamic testing, and also independent of the person performing the interpretation. This paper will explore the Rapid Load Testing method and illustrate the advantages and limitations through a case study in Rostock, Germany

May 1, 2022

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By Willie M. NeSmith, W. Morgan NeSmith, Alan Roach

"In 2013, Augered Cast-in-Place (ACIP) piles are a mature foundation technology throughout the United States. General guidelines for the design and construction of ACIP piles are available along with numerous references for design in specific North American geologies. In fact, the current generation of contractors and geotechnical practitioners might view ACIP piles as just another deep foundation option to be considered, along with driven piles, drilled shafts and others. This acceptance has developed, however, over a 60-plus year period.The term, Augered Pressure-Grouted (APG) pile is often used when referring to ACIP piles because the piles emerged out of construction processes at the Intrusion-Prepakt firm in the late 1940s. The company’s specialty was pressure grouting and preplaced aggregate concrete. The grouting was typically accomplished by driving a pipe to a target level and then injecting grout under pressure. In some soil conditions, it was necessary to use an auger to reach the desired grouting depth. In these circumstances, the grout pipe was driven beside the auger and grout was pumped as the auger was withdrawn. The grout pipe was then withdrawn as well. This was the genesis of the APG, or ACIP pile, and many piles were installed using this technique. The patent application, “Method for Forming Piles” was filed by Raymond Patterson of Intrusion-Prepakt in 1951, and the patent was granted in 1956. The process was eventually modified when a suitable hollow-stem auger was developed. Licenses were granted to the Lee Turzillo Contracting Company and Berkel & Company Contractors, Inc. in the late 1950s. Each of the three companies Patent, LicensesThe patent application, “Method for Forming Piles” was filed by Raymond Patterson of Intrusion-Prepakt in 1951, and the patent was granted in 1956. The process was eventually modified when a suitable hollow-stem auger was developed. Licenses were granted to the Lee Turzillo Contracting Company and Berkel & Company Contractors, Inc. in the late 1950s. Each of the three companies coined their own terms for the piling process: “Pakt-In-Place” for Intrusion-Prepakt, “Auger Pressure-Grouted” for Berkel and “Augercast” for Turzillo. Over time, “Augercast” was frequently used as a generic term for the system. The installation of these piles was, and still is, a highly nuanced process; “contractor dependent” is a term often seen today. Intrusion-Prepakt, Berkel and Turzillo all had personnel who were part of the original group that developed the system and who appreciated the craftsmanship involved in forming sound piles."

Jan 1, 2013

By Gust Van Lysebetten, Monika de Vos

The objectives of monitoring geotechnical structures can be very diverse, including optimisation of the design, quality control, long term performance assessment, and approval of innovative execution techniques. In this context, new measurement techniques, based on optical fibres, offer the possibility of accurate strain and temperature monitoring with very small sensors and limited numbers of cables. This paper briefly presents optical fibre sensing techniques and illustrates their application to geotechnical structures by means of some projects, carried out by the Belgian Building Research Institute (BBRI).

May 1, 2022

By Burt G. Look, David W. Lacey

"Certification of foundation capacity during the construction phase is often assessed by strength or weathering state descriptors based on visual observations. This case study used the Point Load Index (PLI) test as a quantitative tool in the construction certification of a pile’s design capacity. Construction phase tests were completed on irregular sized rock samples whilst comparable design phase testing was completed on intact rock core samples. Statistical comparisons were made to assess the repeatability between the PLI tests, with best-fit Probability Distribution Functions (PDFs) determined for both datasets. Pronounced differences were observed based on the PDF adopted to characterize the PLI dataset, the consequence of which would be a significant change to the pile’s design capacity. The adoption of the lower quartile value is shown to satisfy both design conservatism and construction simplicity requirements. The commonly held belief that rock samples produced during socket excavation may be biased towards the higher strength portion of the rock mass, is shown to be invalid for this site. As the central bridge piers were certified using Plate Load Tests (PLTs), the resultant load-settlement relationships were compared with the PLI strength assessments made for similar materials recovered from the adjacent abutment piles.INTRODUCTIONThe upgrade of the Foxwell Road Overpass across the Pacific Motorway in South East Queensland required the duplication of an existing four span bridge structure. The foundations of the new bridge included the installation of 1.2m diameter cast in place (bored) piles at the bridge abutments and 900mm diameter cast in place (bored) piles below a retaining wall to be constructed adjacent to the existing abutment.The site geology was dominated by the Palaeozoic Neranleigh–Fernvale Beds, predominantly comprised of argillite, sandstone and greywacke. Limited soil materials existed at the site, with Extremely Weathered (EW) rock typically encountered within metres of the existing ground surface. The exception to the existence of shallow rock were locations where existing filling of the site had occurred – i.e. approach embankments to existing bridge structure.Capacity of pile sockets is typically assessed onsite by descriptive rock strength or weathering assessment. Such descriptors encompass a wide range of values and lack precision. Due to the subjectivity of such assessment techniques – a factor of 3 is often observed in terms of strength assessment based on one’s interpretation of rock strength descriptors alone – uncertainty on site often occurs regardless of whether a lower bound, average or other characteristic design parameter applies."

Jan 1, 1900

By Jack Hayes

Vibrating wire strain gages have proven to be a very reliable and effective tool for the measurement of strains associated with the loading of bored piles (drilled shafts). However, when these strains are used to calculate the load, or stresses in the pile, the results can sometimes be confusing and/or difficult to interpret. This paper describes some of these situations, using examples from actual case histories, and discusses some of the difficulties associated with residual load effects, curing and temperature induced strains, load stress distribution effects, estimated modulus and area.

Jan 1, 2002

By John D. Nelson

Foundation underpinning is a common component of remediation schemes for distressed foundations on expansive soils. For many applications in expansive soil, micropiles have distinct advantages over other techniques. This paper will concentrate on the design and construction of micropiles in expansive soil. It discusses the nature of building distress and the relationship between foundation movement and soil heave. It presents methods for determining the factors that are required for the design of micropiles. Such factors include calculation of expected free-field heave, depth of soil wetting, and prediction of pier movement. A finite element program developed by the authors and others to determine pier heave and internal forces is presented. The input parameters that are required for pier analysis are discussed, and the nature of the output and the sensitivity of the results to the output are described. A case example illustrates the advantages of micropiles over other methods.

Aug 1, 2013