Search Documents

By Paul Pedini

The challenge of Contract C19E1 of Boston's Central Artery Project called for the construction of two roadways under the commuter rail yard at North Station. Two options were offered for the method of their construction: Slurry Wall Roof-First or Soft Ground Tunneling. The instability of the indigenous soils seemed to rule out the use of tunneling, so the slurry wall method was chosen. However, these soils were incapable of holding up during slurry trench excavation. After many episodes of ground loss on early panel excavations, Modem Continental Construction suggested a method of trench wall stabilization. The Contractor (MCC) both suggested wall stabilization method and requested that the owner participate in the funding for the effort. The Project and the Contractor were able to agree on a solution which resulted in collapse-free excavation...and found an innovative way to fund the solution.

Jan 1, 2002

By Hidekatsu Takeuchi, Masaru Sakakibara, Shigeo Tanabe, Kenji Harada, Akihiko Suzuki, Shoji Morihana

"Deep mixing (DM) method, one of the most commonly used solidification methods, is based on the principle of solidifying soft ground. It can be classified into two categories such as Cement Deep Mixing (CDM) method and Dry Jet Mixing (DJM) method which apply hardening agent in slurry condition and in powdery condition respectively. In recent years, DM methods have undergone changes that have evolved them from the traditional method to meet the needs of the diversifying market. Among them, the Contrivance-Innovation Clay Mixing Consolidation (CI-CMC) method is a DM method which mixes a cement-type hardening agent in slurry condition mechanically with soils in situ and incorporates the innovative technique, “atomized ejection” that has been developed to allow faster installation of larger diameter columns without sacrificing quality compared with conventional methods. At this technique, the atomized hardening agent is discharged together with compressed air through a device incorporated into the mixing blade. It also has advantages of performing the works with low-displacement of the surrounding soils in consideration of environmental friendliness and with higher penetration capability against hard ground.This paper presents the technological outline of the above-mentioned CI-CMC method, focusing on the atomized-ejection technique, followed by some construction examples, applied to the self-earth-retaining wall, to the hard ground and the area adjacent to the existing structures.INTRODUCTIONAccording to the accumulation of its case histories, Deep Mixing method has been receiving the demands of its application to more challenging conditions, such as harder ground condition, and requirement of lower displacement of the surrounding ground during its operation. In addition, to match its price against the other cheaper methods and widely receive its benefit of higher quality, the cost reduction of Deep Mixing is also one of the major challenges. For the cost reduction, higher productivity and lower consumption of the material to obtain the equivalent strength and homogeneity with the conventional method are required.The Contrivance-Innovation Clay Mixing Consolidation (CI-CMC) method has been developed to meet these demands. CI-CMC incorporates the mist ejection that has been developed to achieve faster installation of larger diameter columns without sacrificing quality compared with the existing methods. Normally, we obtain cement columns of about 1.0 m in diameter by using Deep Mixing method. To increase the productivity, it is not preferable to drastically increase the penetration and withdrawal speed of the mixing blades because of the hardness of the ground and restriction by minimum number of passage of rotating blades per a certain height of the soil cement. Instead, the expansion of diameter of the columns will simply increase the productivity. The development of the new mist ejection system, as shown in Photo 1, has enabled the diameter of soil cement columns to 2.0 m on single axis while 1.6 m on double axes. Mist ejection means that the hardening agent slurry is sprayed into the ground in mist form together with compressed air thereby achieving homogeneous mixing and reducing the resistance on rotating blades."

Jan 1, 2015

By M. Melih Demirkan, Jared Deible, Michael Rosenmeier, Mazen Elias Adib, Juan J. Gutierrez, Raghav Ramanathan

Dewatering and groundwater control is required frequently for construction projects and needs to be accounted for and dealt with care during design and construction to complete the project successfully. Dewatering can cause changes in porewater pressure, which changes the effective vertical stress in a soil mass. Dewatering can also cause changes in groundwater chemistry which in turn can cause changes in porewater pressure and also dissolution of soluble minerals in the soil and rock. The Guideline developed in this study addresses the engineering issues, approaches to lessen the potential risks associated with construction dewatering, and presents dewatering practices to support dewatering applications regulated by the Municipality of Abu Dhabi City (ADM) in the United Arab Emirates (UAE). The subsurface condition within the city presents significant geotechnical problems due to presence of shallow subsurface cavities and soluble minerals in the soil and rock. Therefore it is critical to develop standards for dewatering practices to provide information for local dewatering engineers and contractors with special emphasis to control and to eliminate the subsidence/collapse problems related to dewatering projects within the Abu Dhabi city. The ADM is also responsible for approval of permit applications for projects that involve dewatering. In order to minimize the risk related to subsidence/collapse problems due to dewatering, construction companies and dewatering contractors need to be informed about possible mitigative measures that can be employed to reduce risks. The guidelines were developed as part of this study based on detailed analysis of the local subsurface conditions. A set of rules and regulations are developed for geotechnical and hydrogeological investigations, dewatering design and monitoring criteria depending on the hazard zones, proximity of excavation to critical structures, excavation depth. The Guidelines include examples of permit application packages for three types of dewatering projects; one involving shallow dewatering, one involving intermediate depth dewatering, and one involving deep dewatering. These Guidelines are considered as living document and will be updated as required, as additional information is collected and additional local experience is gained.

Jan 1, 2016

By Michael Cianchetti, Nadir Ansari, Matthew Janes

"PROJECT DESCRIPTIONThe R C Harris Filtration Plant underwent an expansion to install an underground sludge treatment capability consisting of a series of underground tanks within stepped excavations 12m (39 ft) and 10m (33 ft) deep into compact, wet sands over stiff clays and clayey silts.Concerns regarding the original structure influenced designers to set the lateral deflection limit for the proximal front footing at 4mm (1/6 in), (0.03% excavation depth). The design-build team indicated at the time of tender that the movement criteria was unattainable using the tender design. Through extensive Fast Lagrangian Analysis on Continua (FLAC) and a novel construction geometry the design-build team crafted an alternative that produced significant savings over the original concept and met deflection concerns.GEOTECHNIQUEThe hillside site drops 14.5m (47.6 ft) over a distance of 53m (174 ft) between the existing Filter Building on the north and the Services Building on the south. The soils adjacent to the Filter Building consist of 6m (20 ft) of sandy fills, to the footing elevation, over compact sands and layered dense sands and silts to a depth of 10m (33 ft) below existing footing. Beneath the silts lies a 10m (33 ft) thick stiff clayey silt, 2m (6.6 ft) of sandy silt till (containing cobbles and boulders) and an artesian gravelly sand at a total depth of 30m (98.5 ft).The tender information was deemed inadequate to accurately determine soil parameters for a finite element analysis. As a result, the design-build team performed pre-tender Cone Penetrometer Testing (CPT), including dynamic analysis. The CPT data indicated stratigraphy consistent with the conventional bore hole exploration (SPT results) however, the CPT data provided consistently superior soil strengths. The CPT data indicated the sands and silts were dense to very dense throughout their full thickness. The clayey silts below the sands were found to have shear strengths in the 100 to 200 kPa (14.5 to 29 psi) range with an Over-Consolidation Ratio (OCR) ratio of 1.5 to 2. The dynamic analysis, while low strain, indicated very competent behavior with Young’s Modulus values in the 200 to 350 MPa (29,000 psi to 51,000 psi) range. The CPT derived shear moduli and OCR values were vital in determining the soil engineering parameters used for the FLAC analyses."

Jan 1, 2007

By J. Brian Anderson

Jointed micropiles were investigated to support bridge foundations where shallow rock was present. In this application, micropiles would have some amount of unsupported length, and would be subject to nominal lateral loads. Five lateral load tests were conducted on micropiles to demonstrate the impact of casing joints and rock socket embedment on lateral behavior. Load tests were simulated with FB-Multipier, a hybrid-finite element program for analysis of deep foundations, for proper design of the loading apparatus and instrumentation. The micropile sections were 2 m (6.56 ft) long, 273 mm (10.75 in) in diameter, 13 mm (0.5 in) thick walled, with a 50-mm (2-in) long threaded joint. Micropiles were made of one to three casing sections and were embedded 0.3, 0.6, 1.5, or 3.0 m (1, 2, 5, or 10 ft) into rock. In each test, two identical micropiles were pulled together using a simple frame until the weaker pile failed. All micropiles were instrumented with inclinometer casings while two contained strain gages at 0.76 m (2.5 ft) intervals. Load and displacement were measured at the pile heads. Tests showed the embedment of 0.6 m, 1.5 m, and 3.0 m (2 ft, 5 ft and 10 ft) sufficiently carried lateral loads over 180 kN (20 tons). The piles embedded 0.3 m (1 ft) were not able to maintain lateral load. In general, all micropiles tested to failure exhibited a brittle failure mode where there is small lateral deflection followed by a sudden failure at the casing joint. This was demonstrated in three of the load tests. In most cases, the micropiles were stiffer and stronger in the load tests than originally predicted numerically. The final test, where piles were not loaded to failure, verified that embedding vibrating wire rebar strain meters in the grout captured the bending moment profile of the micropile. The results showed the maximum moment in this case being carried directly across the threaded joint as predicted by the preliminary models. The results of these tests were used to calibrate the FB-Multipier numerical model. Using a load test that included bending strain measurements for a match, the soil properties were adjusted to produce reasonable matches for all of the load tests.

Jan 1, 2011

By Mohammed Faizal, Abdelmalek Bouazza

"The operation of ground source heat pumps combined with foundation piles can have an effect on the thermal behaviour of the pile and the surrounding soil. This paper presents the effects of continuous heating, continuous cooling, and alternate heating and cooling operations on ground and pile temperatures as well as the thermo-mechanical behaviour of a field scale energy pile. The effect of pile operation on the ground temperatures is highest near the pile and reduces with increasing radial distance. The results of the present studies generally showed that the thermal elasticity of the pile is not affected.INTRODUCTIONGeothermal energy piles are foundation piles used as underground heat exchangers to maintain thermal comfort in buildings, via the use of ground source heat pumps (GSHPs). Ground source heat pumps are more economical and environmental friendly compared to conventional heat pumps. Energy piles can be combined with supplemental surface heaters or coolers, known as hybrid systems, for forcefully recharging the ground during non-operational times of the GSHP. Alternative heating and cooling of the GSHP improves geothermal energy usage and alleviates heat build-up in the ground and provides a balance of ground temperatures around the heat exchanger (Jalaluddin and Miyara, 2012).The temperatures induced in the piles during GSHP operation can lead to a complex response of thermal strains and stresses in the pile concrete. An assessment of the thermo-mechanical response of energy piles for various thermal loads may assist engineers in the design process. Furthermore, an assessment of ground temperatures will also highlight any potential thermal interactions with other energy piles in actual building operations.At present, the thermal strain and stress distribution in field scale energy piles has mostly been studied for continuous operation (Laloui et al., 2006; Bourne-Webb et al., 2009; McCartney and Murphy, 2012; Akrouch et al., 2014; Mimouni, 2014; Murphy and McCartney, 2014; Murphy et al., 2014; Wang et al., 2015). These studies have contributed considerably to the understanding of the axial thermal strain and stress distributions in the piles and have shown that pile thermal behaviour is mostly thermo-elastic without inducing major structural concerns.The present paper adds to the current knowledge by assessing the pile thermo-mechanical and ground thermal response for continuous and alternating thermal loads of a field scale energy pile. The operation modes studied are 24 hours continuous cooling (Faizal et al., 2015), 24 hours continuous heating, (Wang et al., 2015) and alternate heating and cooling operation (Faizal and Bouazza, 2016). The forced ground thermal recharging is done during the non-operating times of the cooling unit, simulating a solar hybrid GSHP system for a scheduled intermittent mode of operation."

Jan 1, 1900

By Kozo Takeda, Arashi Shimano

"Dry Jet Mixing (DJM) technique is widely known as soil mitigation technique with small ground displacement during installation comparing with other techniques. Some projects involving sensitive structures, however, require smaller impact than in conventional technique. In order to reduce ground displacement during DJM installation, this paper introduces systematic mixing technique, RD-DJM (Reducing Displacement – Dry Jet Mixing). RD-DJM is characterized by injection nozzle on the rim of mixing blade and fin plate on mixing shaft. These devices contribute efficient collection of injected air toward mixing shaft and result in reduction of ground displacement. The authors demonstrate successful performance of RD-DJM indicating difference between conventional installation and RD-DJM technique.INTRODUCTIONThe Dry Jet Mixing (DJM) method is one of the most common techniques in Japanese deep soil mixing field and characterized mechanical mixing of powdery binder with in-situ ground (dry-mixing technique). It is widely believed that DJM Method has great advantages in less quantity of binder to achieve the desired strength and less waste generation during installation.DJM method can meet the required strength with less binder content than wet mixing. And volume of binder of dry mixing is absolutely less than wet-mixing injecting considerable volume of binder slurry. This means that dry mixing causes less ground displacement compared with wet mixing.As the medium for forced feeding of the binder, the DJM method uses compressed air, which is blown from the mixing blade nozzles to scatter the binder and then recovered through the periphery of the mixing shaft to the ground surface. Because the binder is injected outward from the injection orifice at the root of the mixing shaft, a part of the air may escape to untreated areas due to the blockage of air recovery path around the mixing shaft. Figure 1 illustrates possible escaped air and leakage around installation location."

Jan 1, 2015

By M. Meckkey El Sharnouby

In this paper, the results of full-scale field testing of reinforced helical pulldown micropiles (RG-HSP) installed in clayey till soils and resting on sandy soils are presented. Piles were tested under monotonic and two way cyclic lateral loadings. Effect of different loading setups on the results is demonstrated. The factors affecting the piles' performance are discussed. It was found that under monotonic loading the piles were able to sustain displacement up to 50% of the grout shaft diameter. Under low cyclic loading levels, the piles did not suffer degradation in the performance. Also, the degradation rate during cyclic loading increased with the increase of the load level. The experimental results show that the reinforced helical pulldown micropile is a reliable foundation option for lateral monotonic and cyclic loading applications.

Jan 1, 2011

"1.0 DESCRIPTIONThis work consists of furnishing all necessary labor, equipment, and materials to install prefabricated vertical (wick) drains in the ground in accordance with the Plans and as specified herein.2.0 REFERENCED CODES AND STANDARDSASTM D4716-08 Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant HeadASTM D4632-08 Standard Test Method for Grab Breaking Load and Elongation of GeotextilesASTM D4533-11 Standard Test Method for Trapezoid Tearing Strength of GeotextilesASTM D4491-99a Standard Test Methods for Water Permeability of Geotextiles by Permittivity (2009)ASTM D4751-04 Standard Test Method for Determining Apparent Opening Size (A.O.S.) of a GeotextileASTM 6918-09 Standard Test Method for Testing Vertical Strip Drains in the Crimped Condition3.0 QUALIFICATIONSThe Contractor shall have successfully completed a minimum of five wick drain installation projects in similar ground conditions, and installed not less than 5,000,000 linear feet (1,525,000 linear m) of wick drain in the past five years. The Contractor shall have a minimum of five continuous years of wick drain installation experience."

Jan 1, 2014

By Allen Cadden

The type of soil we had was a silty fine sand. It had been placed by hydraulic methods in 1904 so it was quite clean I would say less than 10% silt the rest of it was very loose sand. That I'm not certain, I've only done it on sandy soils but it would stand to reason that some sort of a number should apply because you are measuring the amount of work that you are doing to it so if the soil is fairly consistent over the site it should be able to generalize from there but I don't know for a fact that it works. Well, verifying to ourselves that this method actually worked because we weren't certain at first when we were doing it so then we would develop the numbers and then check the results.

Feb 10, 2003

By João Veludo, Eduardo Júlio, Helen D. Robinson, Jesús E. Gómez

"Utilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. The study resulted in important conclusions on the mechanism of connection capacity development and provided specific recommendations for practical design of micropile-to-footing connections. In the last five years, the original study was complemented by an intensive experimental effort in Portugal aimed at answering many of the questions still remaining on this topic. This paper is a summary of the knowledge that is presently available on the capacity of micropile-to-existing footing connections. It presents the results and observations of model tests performed in the US and Portugal, as well as some tests from actual construction sites. The paper presents clear evidence that friction may be the most important component of connection capacity. It also presents a clear correlation between confinement and connection capacity.IntroductionUtilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. This is often accomplished by drilling through the footing and developing the connection by direct bond between the micropile grout and the existing concrete. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. Smooth and textured micropile inserts of varying lengths were tested to failure inside pre-drilled holes of varying diameters. That investigation led to several publications (Gomez et al. 2005, Wilder et al. 2005, Cadden 2009) on the mechanism of development of bond strength between micropiles and concrete, which included a chart for preliminary bond value selection depending on the diameter of the hole and texture of the micropile.An intensive testing program was carried out in Portugal in the last five years. The program focused on answering questions posed by the original investigation and on finding the relationship between connection capacity and level of confinement. Both investigations, and especially the testing performed in Portugal, provided an invaluable amount of information on the mechanisms of failure of micropile-to-footing connections. This information should be the basis for development of design procedures that, until now, were not available."

Jan 1, 2015

By V. A. Sernov

"One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result building terms and foundation costs reduce considerably. However, nowadays in Belarus there is no reliable and suitable in design practice methods of calculation of piled-raft foundations. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of field and laboratory investigations in Minsk. The most important results of the investigations are provided in the article. Methods of analysis of piled-raft foundations are described.INTRODUCTIONPile foundations of late years are used extensively in connection with the increased number of storeys and load increment on the soil. Often pile foundations are applied in comparative favorable ground conditions at the surface of the base. In such cases the increase of the bearing capacity of foundations and the reduction of construction cost are questions of primary importance for designers. One of the ways to increase the bearing capacity of a piled foundation is to take into account soil resistance in the base of the raft. Piled raft is similar to shallow foundation and can transfer significant part of the load into the base. It allows reducing number of piles in the foundation or shortening their length. As a result, building terms and foundation costs are reduced considerably. However, nowadays there is no reliable and suitable in design practice methods of calculation pile foundations with bearing rafts. In order to devise such methods we have analyzed the results of piled foundation tests fulfilled by various authors up to date and have carried out series of laboratory and field investigations.Long before the constitution of the first piled-raft foundations in the Soviet Union there were attempts to consider soil resistance in the basis of isolated and strip grillages. Such bases can be considered as separate fragments of the piled-raft foundation. Prof. A. A. Bartolomey had tested more than 70 pile foundations of natural size in different ground conditions. The length of piles was 3 12 m (?????????? 1995). The observed results show that the raft carries about 10 12% of the total load applied when length of piles is over 9 m and space between piles is a=3d. Bearing capacity of the raft is about 35 40% when the length of piles is 5 8 m and a=6d. Prof. Golubkov has tested 2 prismatic piles (cross section: 350x350 mm, L=3800 m) and 2 pyramidal piles (cross section: head - 600x600 mm, foot – 100x100 mm, L=3000 m). One of the piles was tested with a raft and the other one without a raft. Significant influence of the raft on total bearing capacity was determined, the more the settlement was the more it influenced on the raft. Bearing capacity of the raft was 27,5% in foundation with prismatic pile and 42% with pyramidal pile (???????? et al. 1971)."

Jan 1, 2016

By Jean-Pierre Hamelin

Ground movements induced by underground excavation are always of critical concern, particularly in urban areas. Compensation grouting now appears as a safe means to control these movements. The paper presents new advanced systems developed by the specialist contractor to bring, at all stages of the project, an efficient control of operations and presents a case history taken from the project at Tren Urbano, Rio Piedras Section, constructed beneath an historic commercial section of San Juan de Puerto Rico.

Jan 1, 2000

By Donald Deardorff

"Helical piles often rely on the final installation torque for ultimate capacity verification. When helical piles are designed using traditional bearing capacity equations for deep foundations and field monitored for a specified final installation torque, a factor of safety equal to 2 is often allowed for the design. One of the more common methods of determining torque during helical pile installation is by correlating the differential pressure across a hydraulic gear motor to a torque. Most drive head manufacturers provide multipliers to convert differential pressure to torque for different drive head models. These multipliers are based on theoretical torque equations and vary with the planetary gear ratio, hydraulic gear motor displacement and drive head efficiency. Drive head manufacturers show a linear fit between the differential pressure and output torque with no scaling effect. Previous drive head testing performed by the author has confirmed that the drive head differential pressure to torque relationship is generally linear however there is a scaling adjustment needed. This results in a variation of multipliers across the differential pressure range for a given drive head.Eight hydraulic drive heads from three manufacturers were field tested by Foundation Supportworks, Inc. to compare the torque versus differential pressure curves with varying installation equipment, hydraulic line sizes and hydraulic flow rates. Differential pressure was monitored using three methods including pressure gages, PT-Tracker and an Ashcroft AT-100. Flow and temperature was measured using a Webtech system analyzer. Torque was measured using a Pro-Dig in-line torque transducer, a TruTorque indicator and a Chance Mechanical Dial in-line torque indicator. The current testing indicates that a change in installation equipment and/or a change in hydraulic flow rate may affect the torque versus differential pressure curve of a given drive head. The results of this testing also show that some of the methods for determining torque during helical pile installations may be unconservative, thereby resulting in safety factors less than required."

Jan 1, 2017

By Donald Deardorff

Helical piles often rely on the final installation torque for ultimate capacity verification. When helical piles are designed using traditional bearing capacity equations for deep foundations and field monitored for a specified final installation torque, a factor of safety equal to 2 is often allowed for the design. One of the more common methods of determining torque during helical pile installation is by correlating the differential pressure across a hydraulic gear motor to a torque. Most drive head manufacturers provide multipliers to convert differential pressure to torque for different drive head models. These multipliers are based on theoretical torque equations and vary with the planetary gear ratio, hydraulic gear motor displacement and drive head efficiency. Drive head manufacturers show a linear fit between the differential pressure and output torque with no scaling effect. Previous drive head testing performed by the author has confirmed that the drive head differential pressure to torque relationship is generally linear however there is a scaling adjustment needed. This results in a variation of multipliers across the differential pressure range for a given drive head. Eight hydraulic drive heads from three manufacturers were field tested by Foundation Supportworks, Inc. to compare the torque versus differential pressure curves with varying installation equipment, hydraulic line sizes and hydraulic flow rates. Differential pressure was monitored using three methods including pressure gages, PT-Tracker and an Ashcroft AT-100. Flow and temperature was measured using a Webtech system analyzer. Torque was measured using a Pro-Dig in-line torque transducer, a TruTorque indicator and a Chance Mechanical Dial in-line torque indicator. The current testing indicates that a change in installation equipment and/or a change in hydraulic flow rate may affect the torque versus differential pressure curve of a given drive head. The results of this testing also show that some of the methods for determining torque during helical pile installations may be unconservative, thereby resulting in safety factors less than required.

By Pawan L. Sethi

Design and construction of deep foundations and basements is increasingly becoming more complex, as the density and frequency of urban development increases. This growth brings various associated challenges in the form of design considerations and construction challenges. This paper discusses some of the challenges routinely encountered as well as some specific complications in this area, based on author’s experience gained through exposure as specialist contractor (designer), consultant and specialist consultant, along with some information on how these challenges were overcome. The paper highlights some of the key aspects of design coordination and importance of having an awareness of the overall perspective. Examples will be used to illustrate practical problems and the approaches used to respond.

Nov 1, 2022

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

By Sven Schröer, Lilma Schimmel, Dimiter Alexiew

"The Geotextile Encased Columns (GEC) deep foundation system for embankments on soft soils was introduced some 20 years ago and is now considered State-of-the-art worldwide.The GECs consist of compacted granular fill, similar to common gravel columns, with one decisive difference: they are confined in a high-strength low-strain flexible geotextile “cylinder” (encasement). This engineered element provides a very efficient tool to control and optimize the behavior of the system. GECs perform very well even in extremely soft soils ensuring bearing capacity (stability) and reducing settlements. Due to the encasement, they a lso provide high lateral ductility. A wide range of fills including sands can be used.The remarkable reduction of vertical stresses in the soft soil surrounding the GECs results in a decrease of lateral pressure as well. Such reduction combined with the lateral ductility allow GECs to be also used for lateral pressure-relief adjacent to sensitive foundations, e.g. rigid piles. The application of GECs as lateral pressure relief was recently used in Brazil and Germany where bridge abutments were built on concrete reinforced-piles. The GECs below the bridge approaches and adjacent to the piles decreased the lateral pressure to acceptable values.This paper presents two case studies for which the most relevant parameters, the geotechnical conditions, specific problems, engineering philosophy, final solution and lessons learned are discussed. Furthermore, instrumentation programs were applied in both projects. The most important results in terms of displacements and stresses are shown, evaluated, summarized and commented upon, focusing on the lateral stress-relief, followed by conclusions and recommendations."

Jan 1, 2016

By Murad Y. Abu-Farsakh, Md Habibur Rahman

The properties of all natural soil deposits are highly variable, and they are rarely homogeneous. Cone penetration tests (CPT) were used to assess the site variability, which was then incorporated into the Load and Resistance Factor Design (LRFD) of pile foundations. Data from six project sites with multiple CPT tests conducted at various locations were collected for this research. The semi-variogram was used to assess the spatial variability of CPT data (corrected tip resistance, qt) for each location. For each location, the coefficient of variation due to spatial variability (COVR,spatial) was calculated. From COVR,spatial and COVR,method, the total coefficient of variation (COVR,total) for each site was calculated, which was then used to calibrate the resistance factors (ϕspatial, ϕtotal) for use in LRFD pile foundation design. The findings of this study demonstrated the importance of using site variability in LRFD pile design. For sites with lower site variability than the design method (i.e., COVR, spatial < COVR, method), the value of the COVR, total will be decreased, and hence the resistance factors (ϕspatial or ϕtotal) will be increased (credit), and vice versa.

Sep 8, 2021

By Stefan K. Schwank

The paper describes the two foundation techniques - mini piles and postgrouted bored piles. The mini pile system is presented with its design and installation parameters, especially the drilling technique. Two case histories demonstrate the application under extremely limited space and traffic conditions and the required modifications of the equipment. After the description of the postgrouted bored piles and its grouting technique, the paper gives a comparison of postgrouted piles and standard piles on a large basic test in Germany. The Brooklyn Queen&apos;s Expressway, N.Y., case history shows the application of this technique after redesign of the original proposal. 1. General Increasing requirements to improve existing foundations to carry additional loads and to increase the bearing capacity of bored piles leads to two new piling techniques: the mini-pile and the post grouted bored pile.

Jan 1, 1991