Search Documents

By Dale Berner, Michael O’Sullivan

"This paper focuses on lessons learned from the innovative designs, in-the-wet construction methodology and modified foundation conditions, for two United States Army Corps of Engineers, USACE, Megaprojects:(a) The over $2 Billion Olmsted Dam across the Ohio River for the Louisville District; and(b) The $1.75 Billion Inner Harbor Navigation Canal, IHNC, Lake Borgne Hurricane Barrier in New Orleans for the Hurricane Protection Office, and the New Orleans District.Design innovations for the 24-inch dia. pipe pile foundation for the Olmsted Dam project include: (i) the use of controlled-fixity moment connections to the dam monoliths in order to tune the response of the dam under the 8.3 Richter scale seismic Maximum Credible Event, MCE; (ii) soil densification to inhibit liquefaction potential and (iii) design to facilitate underwater construction in a river with a highly moveable sand bed.Design innovations for 66-inch dia. concrete cylinder piles for the IHNC floodwall include: (i) the use of soil structure interaction, SSI, analyses to verify capacity to resist deep-seated failure plane in soft soil, while limiting lateral deflections to acceptable limits; (ii) the use of geo-fabric and scour stone for enhanced foundation response and (iii) design for ""in-the-wet"" construction on a fast-track basis.LESSONS LEARNED FROM THE INNOVATIVE OLMSTED DAM FOUNDATIONThe over $2Billion Olmsted Dam on the Ohio River is currently under construction 16 miles upstream from the confluence with the Mississippi River. It will consist of an 800-foot-long tainter gate section, a 1,400-foot navigable pass, two boat abutment sections, a fixed weir section, and upstream and downstream scour protection. The Olmsted Dam and its two, 1,200-foot locks, which were built in 2002, will eventually replace both Locks and Dam #52 and #53, both built in 1929, and thereby bring significant benefits to the Ohio River navigation system.In 2002, the Jacobs/COWI JV completed the design of the dam; which was an engineering challenge for several reasons, including:(a) Its proximity to the New Madrid Fault, could impose an 8.4 Richter Scale seismic event on the structure, which is located in an area of potentially liquefiable alluvium. The extensive seismic analysis performed by COWI included a response spectra analyses; lateral pushover analyses of pile foundations; hydrodynamic added masses; pile group effects; and the development of kinematic motions as a result of the soil-pile-structure interaction.(b) Maintaining vessel traffic along the river and accommodating fluctuating river elevations between 30-40 ft annually, and as much as 60 ft in a 100-year period.(c) Designing for the scour and uplift forces of artesian ground water and preserving a wildlife sanctuary on the Southern shore at the dam site."

Jan 1, 2017

By E. C. Demsky

This paper describes the large diameter caisson foundation for the upstream guidewall at the Lock and Dam No. 26 (Replacement) Project. The guidewall is supported on two rows of 1.8-m diameter concrete filled caissons. The 28.8 m long caissons are embedded 15.5 m into the foundation material and have an unsupported length of 12.2 m. This paper describes the philosophy and design decisions leading to this unique caisson design. The construction success and problems for the load test caisson will be discussed. The full scale 13,350-kN caisson load test and the associated lateral load tests will be described and the test results presented.

Jan 1, 1989

By D. J. Ketkar

It is a frequent experience to find that the Sub-surface Investigation (S.I.) data is either inadequate or misleading. However, such cases are rarely reported. Nonetheless, the projects suffer on-account of delays, cost-over-runs, disputes and/or compromise of the safety norms. Many times S.I. is considered unnecessary or is carried out as a ritual, mainly due to (i) non-availability of good S.I. agencies, or (ii) absence of Geotechnical consultant, or (iii) shortage of time. Importance of S.I. cannot be over emphasised. Yet the profession is in a state of confusion - mainly because of lack of competent professional agencies and of well-defined roles/responsibilities of the concerned parties. In this paper, some suggestions are made to get better returns from the S.I. activity.

Jan 1, 1996

By S. Narasimha Rao

Significant amounts of lateral load may act on pile foundations supporting structures such as transmission line towers, tall structures, bridge abutments, offshore platforms, quay wails, harbour structures and anchorages for water front structures. There were several theoretical and experimental studies conducted on laterally loaded piles in clays to determine ultimate lateral capacity and deflections under working loads. Under a lateral load, a pile deflects in the direction of load application and the soil in front of the pile offers resistance to this movement. The ultimate lateral resistance of a pile can be estimated considering the statics of the pile for a known distribution of soil resistance with depth. In this paper, considering the contributions from both lateral shear drag and frontal passive earth pressure, a method has been proposed to estimate the ultimate lateral capacity of rigid piles in clays. The lateral shear drag has been estimated in terms of adhesion and shape factor. A few load tests were conducted on model piles subjected to lateral loading and these experimental values are used in verifying the proposed method. The reported results obtained from both model tests and field tests were used in support of the predictions made. In all the cases, there is a good agreement between the predicted and measured capacities.

Jan 1, 1996

By Jesse A. Pfeiffer

CPAR, the Construction Productivity Advancement Research Program, is a new initiative of the Corps of Engineers to enhance U.S. construction industry productivity through the development and application of joint-funded research. CPAR seeks to balance the requirements of both the private sector and the Corps of Engineers construction program, to identify research needs that are common to both parties in a partnership for conducting research, and to achieve practical real-world products which will enhance productivity in the construction industry. Increasing costs of doing business has had a major negative impact on much of the nation's industrial base, and research and development (R&D) is among the areas hardest hit. The Congressional Budget Office estimates that since 1984 inflation adjusted R&D outlays in private U.S. firms have risen at an average annual rate of three percent, or about half the rate of gain of the preceding decade. And, despite a significant increase in foreign competition, the portion of gross national product (GNP) devoted to R&D is lower today than 20 years ago. For the case of the U.S. construction industry, the numbers are even more dramatic.

Jan 1, 1989

By Racquel Nottingham, Marc Mastrantuono, Freddy Lopez

In the digital era that we live in, connectivity and mobility play a decisive role in our daily activities. In this context, insufficient telecommunication infrastructure gives origin to the so called “dead zones” (areas with poor or non-existing cell phone reception), which hinder economic development in small communities and in many rural areas, since they remain invisible to a larger marketplace due to the inadequate cellular coverage. Several countries are working to identify these dead zones and with this information, establish strategies together with mobile providers in order to improve the existing mobile networks by expanding the coverage areas. As a result of the analysis, it is expected that thousands of telecommunication towers for 4G and 5G networks will be erected in the coming years. Telecommunication towers are slender elements that require large shallow foundations to verify primarily the safety against overturning. However in remote areas, it can be advisable to consider alternatives to the conventional shallow foundations, in order to optimize the use of materials (concrete, reinforcement steel, etc.). The following article presents an overview of intervention projects, where telecommunication towers were founded on micropiles. The micropiled foundations allowed to reduce considerably the dimensions of the originally planned shallow foundations. Furthermore, the use of micropiles allows for additional optimization, in combination with pre-fabricated foundations (i.e., precast concrete elements, etc.). This paper will focus mainly on the design and the execution of the micropiled foundation.

Sep 8, 2021

By Serhan Guner, Sundar Chiluwal

Although significant research has been conducted on helical piles, there is a lack of research and official design provisions on the helical pile-to-pile cap connections. These connections may govern the global response of pile cap systems—especially in tall and light structures where uplift forces dominate the response. To improve future industry practice, the objective of this study is to understand the influence of pile-to-pile cap connections on the global behavior of concrete pile caps and develop recommendations for their efficient design. For this purpose, 108 high- fidelity nonlinear finite element simulations are conducted to quantify the influences of bracket type, embedment depths, longitudinal reinforcement percentages, shear span-to-depth ratios, and loading conditions on the load, deformation, cracking, and failure behavior of concrete pile caps. The results indicate that the design configurations involving single bracket type may result in premature concrete cracking around the anchorage zones with a 25% reduction in the uplift load capacity. The investigations also confirm that high reinforcement percentages and low shear span-to-depth ratios result in higher load resistance in all bracket types, and that the load capacities of the double and studded bracket types are similar. For applications requiring the use of lower embedment depths, it is recommended that either double or studded bracket types be used. The research findings have applicability to both helical and micro piles given that both include similar connection types. INTRODUCTION Tall and light structures may experience significant uplift forces at their foundations due to large overturning moments from wind or other lateral loads. Helical piles (e.g., Fig. 1a) can provide a cost- effective, practical, and resilient solution for resisting significant uplift forces. In order to realize the full potential of helical piles, it is imperative that the helical pile-to-pile cap connections (see Figs. 1b, c and d for examples) are properly designed to resist the applied forces. However, there is a lack of research and associated knowledge on the influence of pile-to-pile cap connection detailing on the global response of pile caps.

Jan 1, 2019

By Xu Youzai

Static loading teets of five nodular piles and four non-nodular piles were performed in Tianjin soft clayey soil in which measurements of axial force and movements were made. Distribution of shaft resistance and load-movment curves for pile head and pile toe are presented in this paper. The applicability of nodular piles to soft soil and their effectiveness are also discussed. Based on the comparison, it is concluded that nodular piles have an advantage over non-nodular piles mainly in contri­bution to shaft resistance. Dynamic testing was also conducted through R. P. T. for evaluating the service load of tested piles.

Jan 1, 1991

By Emre Biringen

Over the past decades, there has been an increasing recognition of the strategic use of pile-supported rafts in design of heavily-loaded structures to reduce total and differential settlements. However, such a hybrid foundation construction method has not been widely utilized in many countries, including the U.S., due to code limitations. In current practice, the foundation design is based on either (i) the bearing capacity of the raft supported by the subgrade soils, or (ii) solely the pile capacity. This paper addresses the potential use of such hybrid piled-raft systems, where the structural load is shared by both by the piles and the subgrade soils directly beneath the raft, in foundation design of power plant structures. The study assessed some of the characteristics of piled-raft behavior by undertaking three-dimensional finite element analyses of two raft sizes, and various pile layout patterns, including the rafts with piles distributed evenly and only in the central area of the raft. The computer software PLAXIS 3D with the Mohr-Coulomb constitutive soil model was used to facilitate the modeling of such cases. The results presented in this paper indicate how strategically locating the piles could reduce the differential and total settlements.

By Narong Thasnanipan

Performance of diameter 1.5 m toe-grouted bored pile founded at depth 44 m in sand-gravel formation of Chiang Mai City is presented in this paper. Toe grouting was applied by using tube-a-manchette method. Effectiveness of toe grouting was observed from the standard penetration tests conducted immediately below pile toe through grouting pipes at two stages, prior to grouting and three weeks after completion of grouting. Improvement of pile end resistance by toe-grouting is demonstrated with a series of back analyses carried out by load-transfer method employing hyperbolic transfer function. Construction experience of large diameter deep-seated bored piles in multi-layered subsoil and practical aspects of toe-grouting are also briefly discussed.

Jan 1, 2002

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees is applied to a 0.61 m flagpole and a 0.61m fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil is represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2011

By Braxton P. Erbe, Douglas C. Brunot

A variety of systems and techniques exist to support deep excavations where sloping is not feasible. This paper will explore an example project involving the use of pre-engineered hydraulic bracing systems to support sheet pile walls. Challenges on site that drove the final design include a high water table, irregular excavation geometry, and underground obstructions. The hydraulic system, connected by pins and not requiring welds, allowed for quick deployment and the modularity to change as required due to unforeseen site conditions.

By Chu E. Ho

Key variables that govern the jet cutting process are examined based on fundamental theories of jet hydrodynamics and soil mechanics. Under normal conditions of jet grouting operations, lift speed and rotation speed are found to be of less importance than the depth of jetting, nozzle pressure, nozzle diameter, and the soil bearing resistance, with regards to their influence on jet cutting distance. An analytical equation linking the governing variables is proposed, which allows for the possibility of evaluating column diameters achievable in different ground conditions based on theoretical calculations. When used in conjunction with shallow jet grouting field trials, the equation can provide a means for extrapolating trial results to conditions at actual depths for production jet grouting.

Jan 1, 2006

By Roger A. Bullivant

The introduction of this size and type of piling rig is intended to address a multipurpose foundation activity. The 8000 denotes the size of equipment that is attached to the mast, namely 8000 Kg. Larger equipment can be carried subject to adjustment of rig geometry. The 8000 series rig will easily accept hydraulic piling hammers and CFA equipment, but for the purpose of this discussion it will be equipped with an auxiliary power pack that is matched to twin vibrators. The design of the siamesed vibrators allows long tube equipment or piles to be driven with a short mast configuration that provides a lower overturning risk. It is easily adapted within minutes to carry out other foundation requirements that are required on the same contract. The piling and ground consolidation activities that can be undertaken by the 800 series machine are:-

Jan 1, 1995

By D. Waite

The Chairman opened the session by wondering why so few papers on Maritime Structures had been received for this conference. Perhaps because the marine environment is so hostile and the access so difficult that engineers tend to be more prudent about new ideas and designs. Dennis Waite noted the number of grey hairs in the room - grey hairs which could be equated with experience gained the hard way. He hoped that this experience would be passed on in the discussion period of this session. The Chairman was delighted to welcome two authors from China, Mr Sun and Mr Liang. He was most grateful on behalf of the conference for their efforts both in preparing their papers and for being able to present them. He regretted that Messrs Noce and Fedolino were not able to present their paper and then welcomed Mr Christensen from Denmark who would present the first paper.

Jan 1, 1991

By S. F. Fu

The Charkhan Salt Lake area of the Chaidamu Basin in West China is characterized by soft super-saline soils with very high contents of soluble salts. From the engineering point of view, these saline soils are saturated, liquid-plastic and moderately to highly compressible lean silty clay and clayey silt. In the natural state, their allowable bearing capacity is only 60-80 kPa. As to the saturated lean silty clay, liquifaction in case of an earthquake of intensity 7 on the Modified Mercalli scale is considered likely. In order to improve the geotechnicai properties of the saline soils, stone colomn stabilization by means of vibroflotation was performed. As the geotechnicai properties of the soils are closely linked with the amount and composition of the soluble salt content, saline water with chemical content similar to that of the saline soils was used as flush fluid in the course of hole-making and column-forming, with a view to keeping unaltered the amount and composition of the salts in the soils and thereby precluding reduction in or loss of their strength. Systematic monitoring on the behavior of the foundation soils before and after the treatment and comparison of the numerical data thus acquired have shown good technical results, testifying to the effectiveness of stabilization of soft superealine soils by vibroflotation. As a result of the treatment, the allowable bearing capacity was increased one to two fold, accompanied by elimination of the liquefaction potential.

Jan 1, 2010

By Thomas C. Anderson

Thirty-four retaining walls are part of the $46 million upgrade of a 1942 depressed highway in Highland Park, Michigan near Detroit. This project will close a missing link between two newer roadways, I-75 and the John Lodge Freeway. The existing 75 ft. wide, six lane Davison Freeway is being replaced by a eight to ten lane, 200 ft. wide depressed highway in a limited right of way. The highway will be 20-25 ft. deep and 1.5 miles long. A design/build decision by the Michigan DOT saved about 37% of the engineers estimated cost of $19 million for the walls. The successful pre-qualified specialty contractor utilized an innovative solution for the walls consisting of tiedback/cantilevered walls on the north side and mechanically stabilized earth walls on the south side. All of the walls have an identical cast-in-place architectural facing.

Jan 1, 1999

By Zhu Tonghao

A method of calculating anti-slide pile, sheet pile, underground diaphragm and structure with anchors etc. is proposeed in the paper. The effect of the various layers of soil, anchors and bracings etc. on laterally loaded structures may be considered in the model. In the analysis the structure is divided into a series of elements. The transfer matrices of both deformation and internal force are established for each element. According to continuous condition neighbouring element should be connected. Thus the deformation and internal force of each element can be found out in conbination with boundary conditions. The method has a wider adaptability and it can be applicable to a great variety of the analysis of interaction between various structure and soil. If parameters in model are selected properly, the computed results would be in good agreement with the measured data.

Jan 1, 1991

By Todd Nottingham

Channel deepening of major ports is challenging designers to explore innovative solutions to ensure stability of bulkheads, such as for the Oakland Inner Harbor. This particular challenge was met with the use of the SPIN FIN® Tension Pile for restraint of an HZ combination wall along the Oakland Inner Harbor Shoreline in Oakland, California. A SPIN FIN pile is a pipe pile with welded plates at the pile tip that increase pile capacity. A brief history of the project will be provided as well as results of pile load tension tests, pile strain gauge, and wall deflection under construction loads. Tension pile load deflection results will be discussed with recommendations toward establishing deflection-based ultimate load criteria. A discussion of predicted wall loads and field observed wall loads will be provided.

Jan 1, 2008

By Ketan H. Trivedi

This paper describes the method of analyses used for the design of temporary and permanent Secant Pile Walls, describes various aspects of construction including, guide walls, sequence of pile installation, plan alignment and verticality tolerance, methods of drilling (auger, wash boring, cased and open holes), lateral bracing for secant piles, cutting of keys in secant pile walls for the connection of permanent floor slabs, sealing of water leaks and waterproofing. The paper concludes with a brief case history of a secant pile wall project recently constructed in New York City.

Jan 1, 2006