Search Documents

By S. Kanai

Nodular piles is to be piles provided with several nodular projections along the pile shaft, as shown in Fig. 1. Nodular piles are usually installed through either driving method with hammer or preboring method. This paper presents that the bearing capacity installed through each method is considerably higher than that of cylindrical pile without nodules. This paper also proposes the statistically analyzed unique formulae of the bearing capacity of nodular piles.

Jan 1, 1989

By Felix Cheng

Extensions to the Convention Centre in Adelaide, South Australia consisted in part of construction over the existing railway system comprising nine rail lines and passenger platforms. Vibro-pile (Aust) won the design and construct tender with a solution comprising over 500 cast insitu concrete piles. The pile types were 500 to 900mm diameter non-displacement CFA piles and 400mm diameter displacement V-piles. The V-pile is a cast insitu screw pile developed by Vibropile (Aust) Pty Ltd. Both pile types were installed with minimal noise and vibration required for the project, while the displacement V-pile had the advantage over the CFA pile by developing the same pile capacity but with a smaller diameter and with minimal spoil. The latter was important in alleviating spoil removal problems near the railway tracks and disposal of potentially contaminated spoil. The results of dynamic compression load testing and static lateral load testing indicated that the performance of a 400 mm V-pile was equivalent to a 500 mm CFA for this site. The lateral load testing indicated that the surficial soils have a major influence on the load-deflection response, but despite the site containing up to 4 m of filled ground, the piles were found to carry the required lateral loads satisfactorily.

Jan 1, 2002

By Liiban A. Affi

The most difficult task of designing multilevel tieback walls for deep excavation support is the determination of lateral stresses. These lateral stresses act not only on the shored height, but also on the embedded portion of the soldier pile, all the way down to the pile tip. Examples of lateral stresses include uniform surcharge load (soil spoils or equipment), strip load surcharge from Cooper E80 (train loads), line load surcharge (exterior footing or retaining walls), and point loads (cell tower). In this paper we will discuss the various surcharges, do step by step example calculations and show how to take the total lateral stress output and present the design pressures for direct use by the substructural designer. Included is a case study from a project Anaheim Hills, California, USA.

Jan 1, 2010

By Richard Shea

Morris-Shea, an Alabama-based deep foundation contractor, is installing foundation piles at the sites of North America's two largest liquefied natural gas (LNG) terminals currently under construction. The contractor has crews working at Venture Global's LNG lique- faction plant in Plaquemines Parish, Louisiana, as well as constructing foundations for the Cheniere Energy Stage 3 Liquefaction Project in Corpus Christi, Texas. This work includes installing ap- proximately 27,000 DeWaal drilled, full displacement, cast-in-place concrete piles to support seven new midscale LNG trains at Cheniere's Texas ter- minal. Deep foundation installation began at Venture Global's Plaquemines facility, located approximately 30 mi (50 km) south of New Orleans, with an initial phase of 24,000 piles. Plans for the Plaquemines LNG terminal include three loading berths on the Mississippi River and four LNG containment tanks. The facility will utilize new pretreatment com- pressors, liquefaction trains and on- site gas turbine power plants to maintain an annual LNG export capacity of nearly 20 million tons (18 million tonnes) per annum. The site's LNG trains are configured in 18 blocks. The contractor is installing piles through an initial 6-20 ft (1.8-6 m) of cement mixed improved soils, which provide a safe work plat- form for equipment to operate on the extremely weak native soils. Drilling continues through soft clay in the subsurface and tips into a stiff clay or dense sand layer. Production piles are drilled to depths up to 124 ft (38 m) below ground surface. The firm is working with engi- neering, procurement and construction contractor KZJV, a Kellogg Brown & Root and Zachry joint venture, at the Louisi- ana location. The foundation team mobilized at the Plaquemines site in May 2022, to install 16, 18 and 24 in (400, 450 and 600 mm) diameter test piles to depths of 90 and 120 ft (27 and 36 m). The piling contractor returned in September 2022, to start Phase 1 of the deep foundation project, beginning installation of production piles.

Apr 1, 2023

By Alec C. Bloem

A 55' deep excavation encompassing almost a city block in London, Ontario required a lateral earth retention system to provide both temporary excavation support and a permanent groundwater cut-off wall for a proposed office complex. The system selected was an interlocking Drilled Shaft wall with 3-4 levels of tiebacks. The specifications required the system to be designed for movements or settlements around the excavation of ¼" max. Design to be by the Contractor with design parameters and a comprehensive soils report provided. An extensive system of instrumentation in the form of inclinometers and survey targets were used to monitor vertical and horizontal movements of the shoring system and adjacent properties. Introduction The project, One London Place, is a two phase office tower development in downtown London, Ontario. Phase one consists of a 24 storey office tower on the northwest part of the site, with five levels of below ground parking over the entire site "Figure 1". A second office tower will be constructed at a future date.

Jan 1, 1991

By Ke Yang, Robert Liang

"Drilled shaft foundations are widely used for many types of structures, especially for highway bridges, high rise buildings, and costal structures. The lateral design considerations are crucial for those structures that are subjected to lateral thrust forces, winds, waves, and earthquakes. The p-y analysis is the most widely used method for the analysis and design of drilled shafts for lateral load applications in soils. However, existing p-y criteria were developed based on the lateral load tests on small diameter drilled shafts in soils. Although, a lot of lateral load tests have been conducted, there are a limited number of lateral load tests on large diameter drilled shafts embedded in clay. In this paper, a lateral load test on 2.44 m diameter fully instrumented drilled shafts in clay is presented. The site specific p-y curves are derived based on strain gage readings. The existing p-y curves are found to be much softer than the site specific p-y curves. Correspondingly, the deflection at the top of the test shaft under the maximum applied load is predicted to be eight times larger than the measured value using existing p-y criteria. A new p-y criterion is proposed in this paper. The proposed p-y criterion is proven to be able to capture the site specific p-y curves of the load test and to predict closely the deflections at the top of the test shaft. INTRODUCTIONDrilled shaft foundations are widely used for many types of structures, especially for highway bridges and costal structures. The lateral design considerations are crucial for those structures that are subjected to lateral thrust forces, winds, waves, and earthquakes. Although efforts have been made on studying lateral response of drilled shafts; nevertheless, only limited studies have been published on the behavior of large diameter drilled shafts under lateral loads and the corresponding design methods."

Jan 1, 2005

By Antonio Zechini, Giuseppe Iorio, Massimo Grisolia

"The new C Line of the Rome Metro runs northwest to southeast across the city center, with 30 new stations and a total length of more than 15.5 mi (25 km). Due to the presence of a dense urban environment, the selected solution for the construction of the stations consists of a cutand- cover excavation, which is retained by multipropped diaphragm walls to minimize settlement and prevent damage to the nearby structures. The bottom of the excavation of the underground stations are about 82 ft to 98 ft (25 m to 30 m) below ground surface, and about 66 ft to 82 ft (20 m to 25 m) below the groundwater table. To ensure dry conditions and to prevent hydraulic base heave instability, deep well systems were designed and used to lower groundwater level and piezometric head during excavation. The dewatering field tests showed how the local stratigraphy strongly affects the dewatering efficiency. Finite element modeling (FEM) of steady state filtration were used to compare the soil permeability with Lefranc in-situ test results and to verify the efficiency of the grouted plugs. The geological sequence along the new C Line consists of a very heterogeneously layered deposit. The base deposit of stiff overconsolidated clay (“APL,” Pliocene age) is overlain by fluvio-palustrine very dense sandy gravels (“SG,” Pleistocene age), which are then overlain by medium stiff clayey silts or dense sandy silts (“AR” or “ST,” Paleotevere units). These deposits are overlain by covered by pyroclastic volcanic soils, tuff, silty sand and sandy silt (Middle to Upper Pleistocene) deriving from the Colli Albani apparatus. A layer of made ground (“R”) of varying thickness covers the stratigraphic sequence and the natural soil profile everywhere.The local hydrogeological framework is very complex and characterized by a double groundwater system. The upper main aquifer is mainly represented by the “pozzolane sequences” (“PR/PN”), while the lower aquifer consists of a deposit of sandy gravel (“SG,” Pleistocene), which is underlain by marine claystone bedrock (“APL,” Pliocene). The pyroclastic deposits (e.g., pozzolane, lithoid and pseudolithoid tuff and clayely tuff) show large variations in permeability due to porosity, compaction processes, sealing and secondary fracturing. Permeability values for each soil type were determined using Lefranc tests at variable head and using pumping tests. The Lefranc tests indicated a wide range of permeability."

Jan 1, 2017

By Tracy Brettmann

The Highway 146 Bridge Expansion Project across the Clear Creek Channel in Houston, Texas was designed on driven precast concrete piles. However, during construction, the piles along one side of the bridge along the main channel encountered obstructions and couldn’t be installed. These obstructions turned out to be the remnants of a previous bridge foundation at this location, which was unknown to the designers since that bridge had been demolished 40 years ago. Those old foundations were massive 20 ft by 40 ft (6 m by 12 m) pile caps 11 ft (3.3 m) thick supported on precast concrete piles 37 to 55 ft (11 to 17 m) long. The foundation re-design for these locations involved installing a single 78 inch (2 m) diameter drilled shaft up to 125 ft (38 m) long to replace the originally planned driven pile supported pile cap. The drilled shafts would need to be installed within very tight tolerances since they were supporting a single bridge column directly above it. In addition to drilling through the obstructions, this work would need to be completed from barges in 30 ft (9 m) of water capable of dealing with both the current and tides affecting this area. The shafts were installed using a multi-step process. The first step involved coring a larger diameter 100 inch (2.5 m) hole through the reinforced concrete pile cap and removing the concrete inside. This was followed by the installation of a 72 ft (22 m) long permanent casing to and removing the soil and existing precast piles inside. Finally, the drilled shaft excavations were advanced to the completion depths (uncased) using bentonite slurry as the support fluid.

May 1, 2022

By Mandy Korff

Walls consisting of CFA-piles are often used for vertical cut offs for building pits. Several methods of installation and geometry may be used and sizes, depths and strengths of walls necessary vary widely. Based on experience with secant CFA-pile walls in The Netherlands, requirements for this type of wall can be set with a risk management view to it. This paper describes those requirements, based on specific local conditions.

Jan 1, 2006

By A. Daouadji, P. Cazes, S. Grange, L. Briançon, R. Milane

Construction in congested urban areas is often accompanied by geotechnical problems due to high loads and the impact caused by nearby buildings. For this reason, it is important to understand the behavior of the soil and the structure without forgetting the essential role of the interaction between them. Experiments, instrumentation and numerical modeling are the main methods used to study this behavior. To this end, pressure cell, strain gages, vibrating wire extensometers and optical fiber sensors are installed on the reinforcement steel of pile and raft foundations to monitor stresses and induced deformation in these elements during and after construction. A fiberglass rod extensometer is placed in the soil to help measuring the displacement due to excess loading, knowing that the pile foundations are embedded in the Rhône’s alluviums and reach the molasse, a particular and challenging soil with properties that are not yet well understood. The objective of this paper is to present the geotechnical instrumentation program carried out for the tower Silex2 in Lyon, France, and to describe the types of sensors used and their installation on site. INTRODUCTION The complexity of geotechnical structures like dams, bridges or high-rise buildings requires a sound understanding of the behavior of the soil, the structure itself and the interface. Therefore, a geotechnical instrumentation program can be essential in many ways. During the site investigation stage, it can help determine the initial conditions experienced by the soil in the field by measuring parameters such as the compressibility index or the permeability. During the construction stage, real time measurements can protect the structure from premature failure, help validate and optimize the design if needed. In addition, sensors measuring pore-water pressure, loads, deformations and settlements allow for monitoring the performance of the structure. This is called the observational method. Finally, during the operating phase, instrumentation aims to study the long-term behavior of the structure (Nicholson et al., 1999).

Jan 1, 2019

By A. Garassino

A pile design was performed for a thermal power station in Egypt and more than 4000 piles were to be driven. Technical economical reasons suggested the choice of driven composite LACOR piles designed for very high specific loads. Some uncertainties on the behaviour of the pile soil system suggested to perform a test on an instrumented pile. Scope of the test was to verify the possibility of developping the required bearing capacity within the range of the allowable pile settlements values and the effect of the pile joint enlargement on that portion of skin friction to be developped by the upper pile section.

Jan 1, 1991

By Bernard Hertlein

¦ Drilled shafts resist scour seismic loads better than groups of driven piles ¦ Drilled shaft construction creates less noise and vibration than driving piles ¦ Drilled shafts permit direct observation of bearing stratum, and confirmation of location ¦ Drilled shafts are cost effective

Jan 1, 2001

By K. Mallikarjuna Rao

There are several methods available to estimate deflection and ultimate Capacity of laterally loaded piles. In this investigation an attempt has been made to verify the existing methods for prediction of ultimate lateral resistance and deflection with the laboratory and field test results reported in the literature. A 75 pile loading test data obtained from the literature was used to evaluate two methods designed to predict the ultimate lateral resistance of rigid piles and three methods designed to predict the lateral deflections of rigid piles and four methods designed to predict the lateral deflection of flexible piles subjected to lateral loads. The accuracy and precision of each method is quantified statistically. The statistical results of the overall analysis indicate that the mean values of the ratios of predicted to measured lateral capacities vary from 0.62 to 1.14 with an average of 0.88. However, the settlement predictions were much more widely scattered than the ultimate load predictions and in general all the methods have a tendency to under predict the deflections. A new method is proposed by modifying the Broms's method to estimate the lateral deflections of free headed rigid and flexible piles separately. The proposed modified methods were found to be reasonably good in comparison to existing methods and to overestimate deflections.

Jan 1, 1996

By David T. Farber

"Stabilization of an existing cellular tower foundation system without dismantling the tower or compromising the existing foundation system was accomplished by installation of a jet grouted pile system. The tower was originally designed to be placed on a steep hillside and to be supported by a mat foundation founded on existing bedrock. The as-built conditions of the tower foundation system showed it to be constructed on a combination of loose fill of varying thickness and native stiff silts and gravel material. To avoid the potential of differential settlement, a jet grouted pile foundation system was installed to the top of bedrock. The jet grouted pile system was rapidly installed over a two-day period so as to not delay operational permitting of the tower.INTRODUCTIONA tri-legged lattice cellular communication tower was constructed on the side of a steep hill located in a mature hard wood forest. Access to the site as well as available work area was limited to small track type drill rigs and equipment. The original tower design required the tower to be supported by a mat foundation bearing directly on bedrock. Based on a review of the foundation construction and results of a subsurface investigation, it was discovered that the foundation was built directly over a loose fill material that varied in thickness from 0 to 4.27 meters (0 to 14-ft). Because of the uncompacted nature and varying thickness of the loose fill materials, the tower would be susceptible to differential settlement which, could lead to tower instability.The objectives of this project included the following:• stabilize the mat foundation against differential settlement without removing the existing tower structure or foundation system• rapidly complete stabilization activities to allow operational permitting of the towerSOIL CONDITIONSThe subsurface soil conditions that the tower mat foundation rested on were evaluated by installing three borings in a row from the inward slope portion of the mat foundation (B-1) to the outward slope portion of the mat foundation (B-3). Figure 1 illustrates the subsurface soil stratigraphy. The three borings encountered the following subsurface conditions:"

Jan 1, 2005

By Chiranjib Sarkar, Sibapriya Mukherjee, N Kumar Pichumani

With the rapid expansion of urban transportation systems, tunnels and cut & cover structures are considered as the only solution in improving the urban space congestion problem in mass rapid transit system. Therefore, it is necessary to accurately design underground structures with realistic assumptions and considerations of design parameters like site geotechnical data, water table, surcharge load etc. Over conservative approach provides not only uneconomical design but sometimes it also causes overdesign of the concerned structures. Water table depth has a significant role in some design aspects of underground structures like floatation check, lateral and uplift pressure on the buried structure, etc. In current practice of tunnel and cut & cover structure design, water table is assumed to coincide with the ground level. Most of the Design Basis Reports & Outline Design Specifications directly mention consideration of water table at ground level for floatation check and load calculations, etc. However, the actual scenario is different in most of the cities specially in northern, central, western and eastern regions of India except the coastal cities. In the present study an attempt has been made to carry out a parametric study on the effect of water table depth in the design of a typical 6.3m outer diameter circular tunnel with 6m backfill. In this study, it is also attempted to establish an analytical method of calculating the most realistic consideration of water table depth instead of the present hypothetical assumption of considering water table to coincide with the ground level. The findings of the current study may be helpful to the researchers and practising engineers in design of tunnel and cut & cover structure for subways and metros.

Nov 1, 2022

By Ben C. Gerwick

Large diameter steel tubular piles installed vertically or on a slight rake, offer many advantages as the foundations of major overwater bridge in regions of high seismicity. By proper selection of diameter and wall thickness, an optimum balance between stiffness and strength can be achieved. Under strong seismic motion, the piles will deflect and bend so as to reduce the acceleration forces transmitted to the superstructure, while still limiting drift. A major advantage of this concept is that the mass of the footing block is significantly reduced from that of the conventional pier. The design of the footing block requires great care in order to transfer the high shears and moments. Where the soils consist of significant depths of sediments, the kinematic interaction of soils, piles and structures must be considered. Moments will be a maximum just under the footing block. Filling the top portion of the pile with concrete will prevent local buckling and assure ductile behavior even under overload. Typically the piles will be long, with most or all of their support furnished by friction and will require the use of very large pile hammers to achieve the required capacities. Where the piles are founded on rock or in hardpan, sockets will be drilled and filled with reinforced concrete. For these piles, high moments can occur both at the head and just below the rock surface, so the concrete infill should extend the full length. This paper describes the use of tubular piles driven through the deep silty sands of the Jamuna River, Bangladesh, and also where socketed into the near-surface rock for the mail pylon pier of the new San Francisco-Oakland East Bay Bridge in California.

Jan 1, 2013

By Karl A. H iggins, James P. Racine

"Displacement Cast-in-Place (DCIP) piles are not a common deep foundation type in the Washington, DC Metro Area market. As a result, less regional data is available for these foundations compared to other alternate deep foundation types. Displacement cast-in-place piles (DCIP) differ from traditional Auger Cast-In-Place (ACIP) piles in that the pile annulus is formed by pushing a partially-flighted, auger bit to depth via a large mandrel. The auger bit includes a displacing body near the bottom of the tooling. Therefore, little to no spoils are generated during installation and the soil around the annulus is largely densified in-place due to the displacing body being slightly larger than the mandrel it is attached to.Due to this densification, one would expect that the theoretical DCIP capacities (compression or tension) would be greater than an ACIP pile (assuming a pile of similar length and diameter). After 20 static load tests and the installation of over 6,000+ piles on the MGM National Harbor Casino Project, the differences in pile support characteristics between DCIP and ACIP piles of same size and depth was small. The performance of both pile types depended on the density and type of soil within the bearing stratum. In some early cases of DCIP use, the performance exceeded expectations and appeared to be more in line (or better) than typical capacities obtained from driven displacement piles. Other times, the tip elevations could not be achieved or were so difficult to achieve that installation delays occurred and/or significant additional engineering effort was required to address piles short of their requirement embedment.This paper will discuss the limitations of DCIP pile installation in dense Coastal Plain soils and will present the lessons learned during this project. The paper will also compare the DCIP pile type to both conventional ACIP and driven displacement piles utilizing regional and site-specific load test and installation data."

Jan 1, 2017

By Dinesh Hinduja, Pérez: Miguel

"Large structures are generally exposed to dynamic and structural loading. They require usually either foundation connected to hard rock through sockets or driven foundations, which encounter boulders as well.In this regards drilling hard-rock sockets or boulder offshore or onshore can be a challenging job especially when deep foundations are mandatory. To overcome the challenge, specialized equipment like a Pile Top Drilling rig (PBAs) can be used, which have to be correctly set-up and operated in order to get its maximum drilling performance. High performance drilling with PBAs requires maximizing key elements of its operation. The configuration and management of the drill string components are important. The key elements are constant weight on bit which is done by adjusting ballast and managing thrust force; and selection of cutters and proper flowing discharge.The methodology is based on the experience from over 40 years of building and operating PBAs for different project applications. These applications include drilling offshore and onshore for:?Superstructures and buildings?Drilling platforms, barges and jack-ups?Harbours, jetties, dry docks and dolphins?Bridges, piers and causeways?Marine sewerage diffusers?Offshore wind farms?Dam rehabilitationMHWirth documented methodologies demonstrate that by using PBAs properly it is possible to improves performance of underwater drilling for hard-rock sockets and boulders which ultimately reduces project-cost.Background. There is a significant percentage of total project cost in structural foundations. Equipment capabilities and technics to drill shaft with rock-sockets and embedded boulders onshore and offshore are highly developed due to the dramatic equipment advancement and experience in the last 40 years. Formerly, driven piles accounted for the majority of foundations either onshore or offshore, following the experience of previous practice in the market. Nowadays, deep drilled foundations can be constructed to carry the load through the overburden down to the sound load carrying rock or soil.Scope and objectives. The overall objectives of this study are:?Synthesis information on current practices to drill shaft with rock-socket and/or embedded boulders onshore and offshore with Pile Top Drill Rigs?Identify the principal challenges evolving with practice?Provide suggestions for improvements in the construction of drilled shafts through proper operation of Pile Top Drill Rigs?Convey information through case studies and experiences"

Jan 1, 2015

By Junhwan Lee

Pipe piles can be either closed- or open-ended piles. Pile load capacity for a closed-ended pile consists of the shaft and base resistances, while, for an open-ended pile, it consists of shaft, soil plug, and annulus resistances. In order to investigate the pile load capacity of both closed- and open-ended piles, two field pile load tests were performed. For the open-ended pile, the fully instrumented double-walled system was used to separately measure all the components of the pile load capacity. The soils at the test site were predominantly granular soils with relative densities varying from loose to dense with increasing depth. The incremental filling ratio (IFR), which affects significantly the load capacity of open-ended piles, was also measured during pile driving. The test results indicated that the total load capacity of the closed-ended pile was higher that that of the open-ended pile, mostly due to the difference in shaft capacity. The shaft and base load capacities of the open-ended pile were 44% and 20% lower than the corresponding values for the closed-ended pile.

Jan 1, 2003

By Subrata Ray

A large no of power stations are being set up in Chandrapur area having coal deposits. Several industries are also coning up in this area. The subsurface is geologically formed under Gondwana system and consists of shale strata at depths ranging from 8 to 12 m. The stress deformation characteristics of shale exhibits wide variation because of it's geological origin. In view of this, a study was conducted on bored cast in-situ piles installed for a Switch yard project to evaluate load settlement characteristics of three test piles to understand the probable engineering behaviour of the material at the tip and the sides. An approach is developed to simulate the load settlement behaviour as observed in the field, theoretically. This is based on the concept of load transfer. The fit is obtained by varying the parameters, thus may be considered as iterative in nature. The theoretical curves closely matched the observed curves. The results of this study are presented in this paper.

Jan 1, 1996