Search Documents

By Thomas M. Caruso

Construction of a new ship dock at a major Philadelphia area refinery required geotechnical design and field consultation. The new dock, which consists of a system of mooring dolphins and platforms, will be capable of docking the Stena V-MAX Oil Tanker (V-MAX). The 1100 ft long V-MAX is currently the largest tanker to travel the Delaware River and will induce significant lateral loads on the new ship dock. Lateral loads induced on the dock will be resisted by over 200 pipe piles installed on a batter. The piles used for support of the dock included 20 and 30 in. diameter reinforced, concrete filled pipe piles. Complete construction of each pile included driving of the pile to the design ultimate capacity, flushing the pipe pile casing clean of overburden materials followed by drilling rock sockets into the underlying Wissahickon Formation. Variations in depth to bedrock, rock quality and degree of weathering and presence of very hard quartzite lenses created a complex geologic environment that presented challenges for the pile/rock socket design and installation. The design of the pile system, installation methods, QA/QC and testing (Pile Dynamic Analysis), as well as the challenges that were encountered through the duration of the project are presented and discussed.

Jan 1, 2008

By Konstantin G. Ashkinadze

The paper considers performance of piles supporting transient pipe anchors in heavy industrial pipelines. Events such as pump trips or opening and closing of large valves produce short-term dynamic pulses in the pipeline with variable spectral characteristics. Their magnitude is large enough to cause major damage to the pipeline and its anchors, which face horizontal impact loads amounting to hundreds of kN. Design of pile foundations supporting these anchors is often governed by limitation of deflection of the support to prevent overstressing pipeline connections and equipment nozzles. The maximum deflection does not always correspond to the largest load because the stiffness of the soil surrounding the piles heavily depends on the rate of loading. Faster actions encounter stiffer soil response while loads of smaller magnitude applied slowly may be more critical for the deflection time history of the anchor. A typical transient action has both high- and low-frequency harmonics, which makes the response complex. Using load rate-dependent p-y curves published in literature, the paper develops methods of analysis of pile foundations for transient anchors. Pile displacement amplitude – input frequency – natural frequency correlations and time histories of pile response are constructed for typical profiles of transient actions, considering nonlinear soil response to large horizontal loads.

Jan 1, 2016

By G. L. Sivakumar Babu, P. Chaithra

"Raft foundations which are used against differential settlements and for carrying heavy loads can still be subjected to excessive settlements even if it is safe against bearing capacity consideration. Providing additional piles under the raft can reduce such settlements to acceptable values. In addition to settlements, the piles also relieve the raft a part of the total load and thus the bearing capacity of the Combined piled raft foundation (CPRF) is improved. Parametric study of response of piled raft foundation has been conducted and the results have been presented. The study is conducted using finite element based software, PLAXIS 2D. The main objective of the paper is to evaluate the parameters that affect the performance of piled raft for an economical and effective design. It has been shown that piled rafts are an economical solution in foundation design compared to raft foundation, for the soil conditions considered in the paper.1. INTRODUCTIONThe aim during the design and construction process of high-rise building foundations in urban areas is to ensure the lifelong safety and serviceability of the new and existing buildings in the neighborhood. In order to realize this aim in a cost-optimized manner, the combined pile raft foundation (CPRF) was developed (Katzenbach et al., 2005). For the foundation of high rise buildings with good subsoil, the simplest structure considered is a raft. But when the subsoil near the ground surface has low load-bearing capacity, high-rise structures are often rested on piled foundations.A piled raft and pile group serves similar purposes, but there are essential differences between them. A pile group is a set of piles that have a pile cap. The piles would be designed to share the pile load at ultimate state. The pile cap would be designed to link the piles together but the contribution of the pile cap to bearing capacity will not be included in the design. On the other hand, a piled raft is a foundation, wherein piles are provided along with the raft so that the total load acting is shared partly by the raft and partly by piles, rather than being dominated by the piles (as in a pile group). Piled raft foundations utilize pile support for control of settlements with piles providing most of the stiffness at serviceability loads, and the raft element providing additional capacity at ultimate loading (Poulos, et al., 2011). Therefore, piles are included in a foundation for two main design purposes: to provide adequate bearing capacity and to bring down the settlements to an acceptable level."

Jan 1, 2015

By Les R. Chernauskas

? What is Integrity Testing? ? Cross-Hole Sonic Logging (CSL) ? Single-Hole Sonic Logging (SSL) ? Typical Specifications ? Case Histories ? Observations and Conclusions WHAT IS INTEGRITY TESTING? General Definition ? Process in which the condition or structural makeup of an object can be evaluated with respect to defects such as a reduction in cross section (void or crack) or reduction in material strength (water, slurry, soil mixed with concrete). ? If the defect is severe enough, it can reduce or alter the load carrying ability of the object.

Jan 1, 2001

By Alberto Carmona Rosell, Sri Ram Ramankutty

"The installation of Bored Piles and Diaphragm Wall under slurry using tremie raises quality concerns on the integrity of concrete. It is vital to understand the effects on concrete integrity during concrete pouring process. This paper intends to unveil to what extent the compressive strength of the concrete pour is affected in contact with drilling fluid still. Another important angle of analysis proves whether the inclusion of solids particles of un-hydrated fluid could have impact on the concrete compressive strength. The testing comparing the response of concrete compressive strength when drilling fluid is included into the concrete mix altering the water/cement ratio by 5%, 20% and 30%. Comparative results are analysed between two different hydrated slurries namely sodium activated Bentonite and 3rd generation synthetic polymer.1. INTRODUCTIONSoil stabilization is the base for a successful deep foundation execution. The G3 System Slurry developed by Ground Engineering Operations (GEO), with its third generation polymer, namely PolyMud®, is an innovative and unique alternative to the mineral based slurries for soil stabilization, enhancing the quality and integrity of the underground foundation structures. It optimises the production rate of work progress and cost as well. At the same time, PolyMud® slurry is proven to be environmentally friendly.Guaranteeing the maximum quality of the foundation elements according to the initial design is one of the most important objectives and a concern for the foundations contractors. In order to fulfil the project expectations in this aspect, any incident that could compromise the designed concrete integrity and capacity must be avoided.GEO, has carry out its own research regarding effects on the concrete compression results if drilling fluid intermixes with fresh concrete while pouring. To shed light in this regard, GEO, in collaboration with CML (Concrete Materials Laboratory) Sdn. Bhd., carried out empiric tests that analyse this particular event from different perspectives, bringing up the corresponding results that will be studied and commented in this article."

Jan 1, 2015

By R. A. Fraser

Large diameter (1.0 to 2.5m) bored piles have been widely used to support buildings and elevated roadways in Hong Kong. Most of these piles are founded on a hard bearing stratum such as granitic or volcanic bedrock, in the newly reclaimed areas along the water-front, the bedrock stratum can be as deep as 70-80 metres below ground surface, and construction of bored piles to bedrock in this case is difficult and unjustified. Nevertheless, Building Ordinance Regulations in Hong Kong require piles to be founded on bedrock. To overcome this problem for elevated roadways, trial piles have been designed founded on dense, completely decomposed granite. A number of piles have been constructed and subsequently load-tested to allow the rate of mobilisation of skin friction to be measured. This paper outlines the design, construction and testing method, and comments on the test results from several trial piles. GEOLOCICAL CONDITIONS The geology of Hong Kong consists predominantly of acid volcanic rocks intruded by granite. The granite has been deeply weathered, and variations in sea level have produced a drowned coastline with sequences of alluvial, colluvial and marine deposits overlying the weathered bedrock. Reclamation has extended this coastline. Typical site conditions are described later in the paper.

Jan 1, 2010

By Kam Ng

For bridges or buildings that may be subjected to large vertical and lateral loads, drilled shafts offer an economic foundation solution. While the current drilled shaft design practice is considered adequate, introducing a performance-based approach to designing the drilled shafts will make their design more cost-effective and produce more dependable response. This concept was examined using analysis of 41 drilled shaft load test data from several states. This process identified the challenge with the lack of information from the Osterberg (O-cell) load test method to characterize the full top load-displacement response. When a typical single O-cell is utilized in a drilled shaft test, depending on the location of the O-cell and the geomaterials present along and beneath the shaft, the load test result typically quantifies either the side resistance or end bearing reaching the ultimate load-displacement curve but not both components. This limitation hinders the determination of a suitable shaft resistance as a function of a target top displacement. To overcome this challenge, an improved procedure is proposed for establishing the full load-displacement curve based on data gathered from one O-cell. The method will be presented in the paper for three different cases (i.e., side resistance reaches the ultimate during the test, end bearing reaches the ultimate during the test, and neither components reach the ultimate values). Because it allows the characterization of the full load-displacement curve, the proposed procedure will allow performance-based design of drilled shafts with due consideration to settlement while satisfying the Load and Resistance Factor Design.

Jan 1, 2013

By Robert J. Carle

This paper reviews a variety of highway structures which have been built using steel sheet piling as the permanent structural elements of bridge piers, abutments and wingwalls. Those structures built over the past 20 years in Europe include major highway bridges over railroads, highways and waterways in both urban and rural locations. Most highway structures built in the United States using steel sheet piling have been limited to secondary roads in rural locations. The main thrust of this paper is the presentation of various design concepts for highway structures which utilize steel sheet piling. The main purpose is to challenge the profession to move forward from this conceptual presentation and to develop the details necessary to provide safe, cost-effective structures which go well beyond the scope of those being built in the United States today.

Jan 1, 1989

By Richard D. Luark, Fernanda S. Madrona

Designing temporary retaining systems that allow for deeper excavation amid the existing urban infrastructure has become a challenge. A 60-foot-deep excavation in downtown Seattle was required to construct five levels of below grade parking for a 35-story high-rise building, Tower 12, next to an existing 20-story tower with three levels of below grade parking, separated from the project by an 18-foot wide alley. The solution was to combine two temporary excavation support systems, soil nailing and anchored soldier piles, to work within the site constraints. Densely-arranged, short-length soil nails were used to support the upper 30 feet of the excavation, while the lower 30 feet of the excavation was supported with soldier piles combined with steeply-inclined, high-capacity ground anchors, which extended below the adjacent building foundations. The combined temporary support system eliminated the need for internal bracing, reducing construction cost and schedule. The performance of the combined soil nail and soldier pile system was monitored with an inclinometer and optical survey monitoring, which demonstrated the performance of the combined temporary support system. This paper provides a discussion of the advantages of combining different excavation systems and an analysis of movement monitoring data collected. SITE CONDITIONS AND PROJECT INFORMATION Tower 12 consists of a 0.45-acre development with 36-stories of mixed, residential and commercial use with four levels of below grade parking. The project site is bounded by the Cristalla Condominium to the north, Virginia street to the south, 2nd Avenue to the East, and an 18-foot wide private alley to the west. The One Pacific Tower Condominium, which has three levels of below grade parking, was located to the west across the alley. A site layout plan is presented as Figure 1. As shown in Figure 1, the construction of the west wall required a maximum 51-foot-deep excavation, from elevation (EL) 162 feet to EL 111 feet. Adjacent to the west wall, the existing alley grade varies from elevation 154 to 161 feet, leaving a narrow block of soil 18 feet wide and up to 42 feet high to be shored along the alley in order to reach the One Pacific Tower bottom of mat foundation at EL of about 120 feet. In addition to the existing One Pacific Tower Basement wall, site constraints included existing utilities along the alley such as an existing 4.5-feet wide by 7-feet high vault, with bottom at approximate EL 146 located 10 feet from the back face of the proposed Tower 12 basement wall.

Jan 1, 2019

By Arvindh Gupta

BC Hydro proposed to improve the stability of the existing Seven Mile Dam with 54 corrosion protected, re-stressable anchors comprising 92/0.6? strands each, in phase 2 of the program. Being globally the largest capacity anchors ever build, coupled with extra ordinary specifications, the project was a challenge for the entire post tensioning industry. The paper discusses the challenges associated with the anchor material supply as per specifications, extensive research and development carried out by Con-Tech Systems ltd. to overcome the challenges and contribute in making the project a success. The substance of this article is published in the Aug/Sep issue of ADSC magazine.

Jan 1, 2004

By J. L. Liu

Long-term maintained load test on the bored pile group in unsaturated silty soil has been carried out. And the research on the time effects of bearing behavior of pile group has been done by the method of installing pressure cells and reinforcement stress gauges for measuring the soil reaction beneath the cap and the pile bottom as well as the shaft resistance. The test shows that, within a certain duration after loading, the soil reaction beneath the cap and the pile point resistance increase with time; but the shaft resistance decreases. The load distribution among the pile tops in the group tends to be even with time. The shaft resistance redistributes along the pile shaft with time, that is, getting less in the upper part, getting larger in the middle. The redistribution does not tend to stop till the distribution in both upper and middle part becomes to be uniform. The load-bearing conditions of soil beneath the cap of pile group and the variation in time effects with related factors also have been discussed.

Jan 1, 2010

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By Takefumi Takuma, Hiroyuki Nishimura, Shigeru Kambe

"Japan’s Great Tohoku Earthquake and the immediately following tsunami of March 11, 2011 killed more than fifteen thousand people and destroyed numerous buildings and infrastructures in the northeastern part of the country.In addition to reconstruction projects in the areas where the earthquake and tsunami hit, other seismically vulnerable regions in the country have started building new and more robust facilities as well as upgrading existing coastal structures so they will be able to cope with such deadly seismic and hydraulic force. This paper will highlight two different types of aseismic and anti-tsunami levee upgrades currently under construction on the coast of Kochi Prefecture, approximately 500 miles west of Tokyo. The first type is the installation of double sheet pile walls in existing seawalls. The second type is to drive tubular piles into existing levee structures for reinforcing them. Both sheet and tubular piles are being driven by the Press-in Piling Method without removing or compromising the function of the existing structures. 1. BACKGROUNDGreat Tohoku Earthquake of March 11, 2011 caused severe damage to many structures. ASCE’s survey of damaged coastal structures conducted immediately after the disaster by Ewing, et al. (2014) categorizes failure modes of the structures in the following manner.?Overtopping without structural failure.?Overtopping with structural damage or failure.?Wave uplift forces.?Movement of structure off foundation from sliding, rotation, or overtopping.?Impact loads.?Hydrostatic pressure.?Supercritical flows.?Scour.?Erosion.?Abutments end effects.?Subsidence."

Jan 1, 2017

By Amalia Giannakou

When designing structures in seismically active areas, foundations of critical structures are typically located away from known faults. Indeed many seismic codes prohibit construction in the immediate vicinity of seismically active faults establishing minimum setbacks from the faults. However, for long structures such as bridges, tunnels and pipelines, a fault maybe unavoidable, and fault rupture risk impossible to preclude. This paper presents a case study of a bridge foundation design that incorporates the consequences of fault deformations passing through the foundation. A series of site surveys were conducted to characterize the fault environment, and fault displacement hazard analyses were conducted to develop design displacement demands. Subsequently, numerical analyses were performed to evaluate the fault rupture-induced demands on a pier foundation in terms of displacements and rotations. Initially, analyses were performed that model the free field fault rupture propagation to the ground surface of the fault to ensure that the basic site characteristics are captured. Subsequently, the foundation elements were introduced in the model and the fault rupture is simulated again. The interaction and influence of the foundation on the fault rupture propagation is calculated, and the consequent demands and distortions of the foundation block provide a basis for structural engineers to design the bridge.

By K. Viking

It's well known that conventional impact hammers, usually are the method to use in order to drive precast prestressed concrete piles. However sometimes the vibratory technique might be considered as a suitable alternative due to favourable soil conditions. It is also well known that piles driven into granular soils can be installed more efficiently by the use of a vibratory driver compared with impact hammers. However, the use of the vibratory technique is seldom regarded as the first choice, since the technique is constrained by several uncertainties related to the pile capacity, and concrete piles to cope with tensile stresses. With the opportunities of having suitable subsurface conditions and a fair amount of piles to be installed, it was anticipated that the use of the vibratory method could result in a significant reduction of the installation costs. Part of the uncertainties of using a vibrator was intended to be eliminated by restriking the vibratory driven pile with an impact hammer and use a Pile Driving Analyzer? (PDA) to correlate recordings of soil resistance to driving with measured rate of penetration, and to evaluate the static capacity and load/settlement characteristics of the vibratory driven pile by conducting static load test. The conducted test study of using a vibrator to drive the precast prestressed test pile (14-in. square by 30-ft-long) did not turn out to the author's complete satisfaction. The present paper focuses mainly on a numerous practical engineering issues in relation to the use of the vibro-technique to drive precast prestressed concrete piles in granular soils. The obtained experiences of using a PDA to monitor vibro-driven piles, with its potential and limitations, is presented and discussed. Furthermore, a simple method of how to subjectively pre-estimate the soil resistance due to vibratory driving is presented and discussed. The reasons for the partly unsuccessful test study are discussed in great detail based on the obtained experiences. Suggestions of how to better approach a similar situation in the future are also provided in great detail

Jan 1, 2004

By A. C. Ackenhell

The geologic environment of Pittsburgh, Pennsylvania is both inviting and challenging to drilled pier installation. The shales and clayey soil zone of the hills are favorable but the alluvial soils of the three major rivers create problems. Beginning in the early 1950's, drilled pier installation continually improved as methods were developed to meet the geologic challenge. Case histories are presented to illustrate the historical development of piers in Pittsburgh. Recent innovations reducing the groundwater problem are illustrated by a case history of a high rise building construction. Load test information for side wall shear on the cylindrical shaft area between the concrete and bedrock continues to be desired but remains generally uneconomical.

Jan 1, 2010

By Padmavathi V, M. Najamuddin, M. R. Madhav

Granular piles are one of the leading ground improvement techniques, adopted for the betterment of bearing capacity and reduction in settlements of the foundations and also to accelerate consolidation of the surrounding soil. In the recent past, there has been extensive research on the settlement analysis and behavior of granular piles under varied soil conditions. The application of these theoretical solutions to practical problems requires a knowledge of representative values of the deformation parameters of the ground and the granular piles. However, very little information is available on these parameters. The paper presents a new method for the estimation of the modular ratio of granular piles and modulus of deformation of the surrounding in-situ soil from the compression load tests. The load - settlement response obtained from the compression test results are used in the back analysis for estimating the modulus of deformation of the ground. The presence of granular bed, under the rigid plate for load testing, has been given due consideration in quantifying the proportion of load transferred on to the stone column. Based on these considerations a new method is developed to estimate the modulus of deformation of the ground and the modular ratio of the granular pile.

Sep 1, 2022

By Tomio Tsuchiya

A construction method of bored steel H piles enclosed in soil-cement columns was developed by modifying steel H piles from the driven pile method and soil-cement walls from the earth retaining wall method, the latter of which produces cut-off walls and reduces noise and vibration during construction. In this method, as shown in Figure 1, rich mix cement paste is injected into the bottom of a borehole which is pre-excavated by a casing auger, then a steel H beam is inserted before it hardens. Since the high vertical resistance of piles created with this method has already been confirmed by loading tests, we have been investigating the applicability of this method for piles used to temporarily support building loads for top-down construction on raft foundations until the raft foundation is completed. However, in the loading tests, the bearing capacity at the lower end of the pile was measured by loading from ground surface on test piles which had friction cut to eliminate the shaft friction resistance. In other words, the loading tests neglected the effect of overburden pressure of soil above the lower end of the pile. To investigate the effect of the overburden pressure on the bearing capacity at the lower end of the pile, loading tests were carried out on a bored steel H pile of lm diameter (test pile) bored in a compacted sandy soil layer with N-value of 100 to 250 at each stage of a three-step excavation. The results show no significant change in the bearing capacity at the lower end of the pile when the depth ratio of the pile is in the range of 5.7 to 22.7.

Jan 1, 1996

By John P. Briand III, Douglas J. Aghjayan, Robert E. Fosse

This paper highlights the successful pile load testing program for the redevelopment of Pier One in East Boston, Massachusetts. Pier One is a 5.4-acre parcel on a dormant waterfront site used in the 1950s as a warehouse and distribution facility. The developer plans to re-use the existing 14-inch-diameter concrete-filled steel pipe piles to support four 5- to 7-story apartment buildings above a 2-story parking garage. A pile load testing program was developed to establish if the existing piles could support design loads of 240 kips for project financial feasibility and up to 300 kips for a significant reduction in future foundation costs. The Phase 1 program consisted of statnamic and dynamic load testing on two piles with two loading intervals (200 and 240 kips). Based upon the favorable results of the Phase 1 program, the Phase 2 program involved statnamic load testing on two piles and dynamic load testing on ten piles with three loading intervals (200, 240, and 300 kips). The Phase 2 program confirmed the favorable results which were applied across varying strata thicknesses and pile embedment depths. The average allowable capacity for the piles tested was greater than 300 kips with pile movement up to 0.3 inches.

By Rasin Duzceer

In this paper, the results of pile load test on 24 piles from twelve sites are presented. The pile load tests were performed on 14 driven and 10 bored piles of varying diameters and lengths installed in different ground conditions in Turkey, Saudi Arabia and Kazakhstan. The purpose of this study is to evaluate and compare the axial capacity of the piles obtained using pile load test interpretation methods. Davisson, Brinch Hansen %80, Chin-Kondner, Shen-Niu, De-Beer, Housel, Mazurkiewicz, Fuller-Hoy, Brinch- Hansen (90%), Corps of Engineers, Butler Hoy and Tangent Intersection methods were used to determine the axial capacity of the piles. Static analysis using FHWA method was performed to predict the axial capacity of the piles. A statistical analysis was performed to compare and quantify the load test interpretation methods. The ratio of interpreted (Qi) to predicted (Qp) pile capacity was compared for each method. For each pile load test and for each interpretation method, the mean and coefficient of variation of (Qi)/ (Qp) were calculated. Among twelve methods investigated, the highest Qi/Qp value was obtained as 1.37 for Chin-Kondner method whereas the lowest Qi/Qp ratio of 0.70 was obtained from De Beer method.

Jan 1, 2002