Search Documents

By Liang Shen

The Cooper River Bridge, the longest cable-stayed bridge in North America, replaces two existing bridges along U.S. Highway 17 and connects the City of Charleston and the town of Mount Pleasant, South Carolina. Two diamond shaped towers support the 1,546 ft long main span over Cooper River and allows for a 1000 ft wide navigation channel. The Charleston high-level approach is 4351 ft long and provides a 250 ft wide navigation channel for Town Creek, while the Mount Pleasant high-level approach is 2,090 ft long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. From various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against vertical and lateral loadings. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies the coastal sediments of the interbedded clays and sands. A group of 11 shafts supports each main tower, while a rock island protects it from vessel collision. A group of 4 to 8 shafts foundations support the other piers of the main span unit. A pair of shafts supports the High Level Approach piers. The shaft tip elevations vary from 120 ft to 230 ft below water line. An elaborate geotechnical investigation was conducted on the site, including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2013

By Xiong Houjin

In the excavation works of some deep foundation pits within the boundaries of Guang­dong Province of China, though some measures, such as steel sheet piles, diaphragm walls, etc. were taken to protect the walls, the construction of the excavation works was often accompanied by damage of buildings and public facilities, surface settelment. sand boil and collapse of piles. When these happened, only chemical grouting could be used as the most efficient measure for rushing to deal with or rescue the emergencies. Besides, the application of chemical grouting protection wall technique also palys a very important role under the geologic conditions of the coastal areas of Guangdong Province, when applied in the mucky oystershell layer wealthy in water and the deep mud layer, it can not only achieve good results, but also reduce the cost significantly. In this paper, we discuss the water-tight and earth retaining functions of chemical grouting protection wall in weak formation, and introduce the applicable ranges of chemical grouting protection wall in the excavation of deep foundation pits. Some technological principles and design considerations of the construction of chemical grouting protection wall are presented. Different types of protection wall are also introduced.

Jan 1, 1991

By N. Aarthi, G. R. Dodagoudar

The improvement of soft clay deposits using stone columns is a well-established ground improvement technique in the western world. This technique has been well documented and has proper design codes for precise execution in the field. The sand compaction pile (SCP) method is a contemporary technique to stone columns and has limited literature related to the strength characteristics of the loose to medium dense sand deposits treated with SCP. The available studies on the SCPs installed in cohesionless deposits focused on the improvement by indirectly assessing the SPT-N values pre- and post-installation of the SCPs. The widespread implementation of the SCP technique in recent years has increased the need for a more direct evaluation of the improvement. Earlier studies in this regard have revealed that the available design solutions are based on the type of installation equipment, their working efficiency, and accumulated field data. However, it is found that there are no generic design codes for the direct estimation of the ultimate bearing capacity of the SCP improved cohesionless deposits. To meet the design requirement for the SCP treated ground, a series of experimental and numerical investigations are performed in the present study to arrive at a direct framework in the form of design charts based on the pressure-settlement response of the treated ground. The developed design charts give the ultimate bearing capacity (UBC) of the treated sand deposit for the known initial relative density (RD) of the deposit, spacing and diameter of the SCPs, size of the footing, and for the specified target unit weight required for the intended application. It is concluded that the design charts will be of preliminary use to the design engineers to directly evaluate the UBC of the SCP improved loose to medium dense cohesionless deposits as part of the SCP method of ground improvement. It is expected to have more field-scale experiments and in-depth analysis before implementing these charts for actual field execution.

Nov 1, 2022

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007

By Frank Haehnig, Harald Krenn, Harm-Christoph Claassen

"The Wadi Dayqah Dam Water Supply Scheme represents one of the most important projects implemented by the Sultanate of Oman to ensure sustainability of water resources. The principal components of the project comprise two dams to impound the Wadi Dayqah, to store and supply drinking water to the local area and to Muscat, the capital city of the Sultanate.The Main Dam with a central spillway is a RCC Gravity Dam with a maximum height above foundations of 75m, crest length 400m; the Saddle Dam is a rockfill dam with central clay core, max height above foundations is 49m and crest length 360m. During construction of the Saddle Dam a key trench was excavated to 10m depth and filled with compacted clay connected to the central core of the embankment. Grouting utilizing cement grout was performed as a single line grout curtain prior to each filling operations. Both Dams are founded on soft Siltstone, Claystone, Sandstone and inter-bedded harder limestone.After construction of the Saddle Dam, once water was in the reservoir it became evident in early 2010 that some seepage was occurring apparently from the right abutment. This seepage became more marked when the reservoir first filled to discharge over the spillway in June 2010. In order to reduce the seepage, additional sealing works by drilling and grouting of a three row curtain up to 80 meter target depth were initiated to supplement the existing single row curtain. Part of this project for the sealing works has also been to drill additional investigation holes to provide more information and confirm extend of the additional sealing works and its limits.Züblin Ground Engineering was awarded the Additional Sealing Works Contract. Whilst Equipment was on Site, the opportunity was taken to carry out drilling and grouting on the Left Abutment of the Main Dam to reduce seepage through that abutment and to install additional standpipe piezometer for future monitoring of seepage patterns.Work on this Contract started on site in January 2013 and was substantially completed in January 2015.At the time of Tender Züblin Ground Engineering propose and Alternative Design in the form of a Secant PileCut-Off Wall, 85m long to a depth of 40m with additional drilling and grouting below the foot of the cut-off which was then included in the contractual scope."

Jan 1, 2016

By Shawna Munn, Carol Dounitch, Erika Acton

The EQ Bank Tower, a 24-storey office tower with 4 levels of underground parking, is currently under construction at 25 Ontario Street in the downtown core of Toronto, Canada. The tower geometry required an 18 m (60 ft) deep excavation inside an existing 3-storey 100-year-old façade, to be retained in place throughout construction. This presented a variety of design challenges that required several innovations and a customized monitoring program. In this paper, we will discuss two major challenges, and highlight the innovative and adaptable solutions carried out using performance-based design leveraging the observational method. The first was installation of a shoring system in a 500 mm (20 in) gap between the historical façade and a live gas main. The second involved excavating 10 m (33 ft) into expansive shale bedrock adjacent to a sensitive neighbouring building.

Oct 1, 2022

By Seyyed Mehdi Radeghi Mehrjou

It is important to study structures and their retrofitting techniques in order to avoid earthquake-induced seismic damage within countries that are prone to earthquakes. Todays, micro piles are employed as useful structural components for seismic behavior improvement. The present study analyzes inclined micro piles subjected to seismic loading by using the three-dimensional finite difference method (FDM). FDM assumes an idealized three-dimensional soil-micro pile model to perform logical behavior evaluation in the event of an earthquake. Linear and elastic micro piles and elastoplastic soil were employed in this study. The Mohr-Coulomb criterion was employed in the failure control of the micro piles. The micro piles were subjected to the 1978 Tubas earthquake records. The numerical results were compared to experimental data. The comparison revealed good agreement between the numerical results and experimental data. The inclined micro piles were found to sufficiently enhance soil strength under seismic loading, inducing smaller displacements than vertical micro piles. Furthermore, the soil and inclined micro piles showed salient interaction.

Sep 1, 2022

By Peter Cali, Wesley Schmutzler

"The Deep Mixing Method (DMM) was employed to raise and support the LPV (Lake Pontchartrain and Vicinity) -111 Levee in New Orleans. Even using innovative technologies, the tight schedule to achieve the 100 year elevation by June 1, 2011 was a daunting endeavor. The size and scope of DMM proposed for LPV-111 was on a scale never attempted outside of Japan. Over 1.65 million cubic yards of DMM was installed. LPV-111 is adjacent to the Bayou Sauvage Wildlife Refuge, which is the largest urban National Wildlife refuge in the United States. By utilizing DMM to control settlement and improve stability of the taller levee, side slopes were steepened from the conventional 1V:4H to 1V:2.85H, thus avoiding encroachment into the Bayou Sauvage and reducing the amount of clay needed for the completed levee. The COE utilized Early Contractor Involvement (ECI) for this contract. The ECI process allowed for input from the DMM contractor, TREVIICOS South, in order to optimize equipment resources and material requirements. This paper gives an overview of the extensive DMM requirements for LPV-111 and explains the benefits of the ECI process.IntroductionDuring hurricane Katrina the levee that constitutes LPV-111 was overtopped and breached in several locations. The United States Army Corps of Engineers (USACE) was presented with the task of increasing the level of the flood protection around New Orleans after Hurricane Katrina to the 100- Year hydraulic grade - the level of protection that provides risk reduction from a storm surge that has a 1% chance of being equaled or exceeded in any given year - and the firm project completion deadline was June 2011.LPV-111 is located in East New Orleans and a large portion of the levee is adjacent to the Bayou Sauvage National Wildlife Refuge. The levee could not encroach on this area. This provided a limited footprint for the levee and made construction of conventional levee difficult, if not impossible. The total length of the project was 5.3 miles. Included in the project was the rehabilitation of one main pumping station and one smaller pump station for water management within the refuge. Short sections of “T” wall were used at the tie in at the Lake Borgne Surge Barrier, the main pump station and the CSX Railroad crossing"

Jan 1, 2017

By Shenbaga R. Kaniraj

The pile loading tests are generally conducted to assess the safe load on piles in compression. In the Indian practice, the safe load is determined using the pile loading test data and the two criteria specified in the Indian Standard Code, IS.2911 (Part 4) -1985. For this, the test pile should have undergone a minimum displacement equal to 10% of the pile diameter. Often, the piles are not subjected loads that are sufficient to cause a displacement of this magnitude. If the settlement is at least 12 mm, then the safe load is determined based only on the first criterion. But, if the settlement is less than 12 mm, the safe load cannot be determined using the IS Code criteria. The paper presents two procedures called hyperbolic and generalized hyperbolic methods to estimate the safe load using the IS Code criteria even when the loading test data is insufficient. The data from two initial tests have been analyzed. The predicted safe loads have been compared with the actual safe loads.

Jan 1, 1996

By David J. Baxter

Use of bored displacement piles has experienced significant growth in the UK piling market sector, largely due to their environmental advantages over other piling methods and through cost benefits. Bored displacement piles are a cast-in-situ construction which can be formed with minimal production of spoil and offer low noise and vibration compared to driven displacement piles. A large variety of bored displacement piles have been developed. This paper describes a standard system for their classification. The development of the different types is described along with the factors which have led to their increased use. Consideration is given to processes undergone by the soil during pile installation and design approaches for bored displacement piles are compared. Comparisons are made between the different classifications of bored displacement pile. Comments are also made on the installation of such piles. It is concluded that complex changes occur in the stress states of the surrounding soils. Such effect of the pile installation on the soil should be accounted for and there is a need, therefore, to further refine the design process for these piles.

Jan 1, 2006

By Gerald Verbeek, Erick Baziw

Cone penetration testing (CPT) is a popular and cost effective tool for geotechnical site characterization. CPT consists of pushing at a constant rate an electronic penetrometer into penetrable soils and recording cone bearing (qm), sleeve friction (fs) and dynamic pore pressure (u) with depth. The measured qm, fs and u values are utilized to estimate soil type and associated properties based predominantly on empirical correlations. The cone bearing measurements are highly susceptible to additive measurement noise for sandy, silty and gravelly soils. This measurement noise results in high peaks due to interbedded gravels and stones and low peaks due to softer materials or local pore pressure build-up. To date there has been little progress in filtering this additive noise aside from ad hoc techniques, which include discarding qm measurements and smoothing/averaging qm measurements. This paper outlines a qm filtering technique which attempts to put structure into the estimation problem. In this case, the dynamics of the cone bearing measurements are modelled within a state-space mathematical formulation and a Kalman filter (KF) is then utilized to obtain optimal estimates of qm. The mathematical details of the qm KF algorithm are outlined in this paper along with the results from a challenging test bed simulation.

Sep 8, 2021

By Gerald Verbeek, Erick Baziw

Cone penetration testing (CPT) is a popular and cost effective tool for geotechnical site characterization. CPT consists of pushing at a constant rate an electronic penetrometer into penetrable soils and recording cone bearing (qm), sleeve friction (fs) and dynamic pore pressure (u) with depth. The measured qm, fs and u values are utilized to estimate soil type and associated properties based predominantly on empirical correlations. The cone bearing measurements are highly susceptible to additive measurement noise for sandy, silty and gravelly soils. This measurement noise results in high peaks due to interbedded gravels and stones and low peaks due to softer materials or local pore pressure build-up. To date there has been little progress in filtering this additive noise aside from ad hoc techniques, which include discarding qm measurements and smoothing/averaging qm measurements. This paper outlines a qm filtering technique which attempts to put structure into the estimation problem. In this case, the dynamics of the cone bearing measurements are modelled within a state-space mathematical formulation and a Kalman filter (KF) is then utilized to obtain optimal estimates of qm. The mathematical details of the qm KF algorithm are outlined in this paper along with the results from a challenging test bed simulation.

Oct 1, 2021

By Lassaad Hazzar

The ultimate lateral resistance of piles in cohesive soil is studied using the well-known finite difference code, FLAC2D. The Modified Cam Clay (MCC) constitutive relation is adopted in the analyses to model the cohesive soil behavior, whereas the structural pile model with three degree of freedoms, available in FLAC2D library, is adopted to model the piles. The reliability of Broms's method, still used in the current design practice of piles under lateral loads, is verified. Comparisons between the ultimate lateral resistances of piles and those deduced from the graphs proposed by Broms (1964) are presented in graphs. Different factors thought to affect the lateral resistance of piles in cohesive soil, not adequately considered in Broms's method, such as clay stiffness, pile length, pile diameter and axial load are parametrically studied. A special concern is devoted to elucidate the effects of over-consolidation ratio (OCR) on the ultimate lateral resistance of piles in cohesive soil.

Aug 1, 2013

By Thomas A. Printz

The wide use of carbon steel in construction and engineering projects makes this engineering material accountable for approximately 85% of the total annual steel production worldwide. Despite the lack of corrosion resistance of carbon steel, it is incorporated into the permanent work for marine applications, power plants, transportation projects, chemical processing, mining, petroleum production and refining, pipelines, mining and construction equipment. Corrosion is an electro-chemical process that occurs in the presence of water and air. When an electric current is introduced to water or soil, the rate of carbon steel corrosion increases rapidly. Gaseous atmospheric constituents that are capable of electrolytic activity can also increase the rate of corrosion. Corrosion tends to be more rapid in environments in which the steel is exposed to water, and then air, rather than being constantly submerged. The exposure to seawater increases steel pitting because the electrical conductivity is improved in salt water.

Jan 1, 2013

By Karl A. Higgins

In 1976, Prof. G. G. Meyerhof published a famous article in the Journal of Geotechnical Engineering titled ?Bearing Capacity and Settlement of Pile Foundations?. This article presents the authors opinions on calculating pile capacities in clays and sands, group capacities and pile settlement. A portion of the article presents correlations of shaft friction and end bearing to the Standard Penetration Test (SPT) N-value. Subsurface exploration via the Standard Penetration Test is the most widely used exploration tool in the United States, so correlations of pile capacity to N-value are significant to the practice of geotechnical engineering. Meyerhof?s SPT-N correlations are relatively simple calculations compared to other pile capacity computation methods presented in the article or found in other text books (such as the a-method, b-method, Nordlund, Vesic, Meyerhof?s semi-empirical, others) and therefore are popular amongst practicing geotechnical engineers. At the time these correlations were published by Prof. Meyerhof, utilization of dynamic testing with the Pile Driving Analyzer (PDA) was not widespread in geotechnical engineering practice. Prof. Meyerhof?s correlations appear to be based upon conventional static pile load testing of instrumented piles. Dynamic pile measurements to estimate a pile?s static capacity provides certain advantages over conventional static load testing, namely the determination of unit shaft friction values at discrete intervals along the pile, and the unit end bearing support value. The author has compiled a database of driven, displacement piles tested with dynamic methods (ref. ASTM D4945, Test Method for High-Strain Dynamic Testing of Piles). The data was collected between 2002-2010 and is comprised of displacement piles driven into coastal plain sediments in the mid-Atlantic states of Virginia, Maryland and the District of Columbia. In layered soils, dynamic testing in particularly helpful as it reveals the differences in unit shaft friction for varying soil types. One hundred ninety (190) piles are included in the database, with a corresponding 1,373 discrete shaft friction and 190 end (toe) bearing measurements. The pile type typically consisted of 12 and 14 inch square, prestressed, precast concrete piles; however, a significant number of piles were steel HP 12 or 14 inch sections. The database was sorted based upon soil type, and then correlations of shaft friction and end bearing were derived in the same or similar manner as Meyerhof?s original 1976 publication. The new correlations are compared to Meyerhof?s original values.

Jan 1, 2011

By Charbel Khoury, Kwabena Ofori-Awuah, Kofi B. Acheampong

"Following heavy rains in spring of 2014, Prince George’s County officials issued a mandatory evacuation for homes in the Piscataway Hills subdivision of Fort Washington, Maryland where a landslide along a 1700-foot hillside destabilized homes, collapsed the single access road, and resulted in water and sewer mains break. Forensic investigations, including geologic assessments, test borings and in-situ Cone Penetrometer and Dilatometer soundings, were performed to evaluate subsurface conditions and provide stabilization options for the roadway and slopes. Post-failure ground movements were monitored using inclinometers. Critical failure planes were identified within the underlying 30-foot thick Marlboro Clay formation, a known geologic hazard with historic occurrences of landslides and slope failures.This paper discusses the remedial design for stabilizing the landslide and 60-foot hillside slope failure, and protecting the roadway. Amongst several feasible options, driven piles were selected in consultation with the County and retained contractor based on cost, environmental impacts and site constraints. Constraints included private ownership of hillside slope, upslope buildings safety; deep-seated failure, relocation of underground water and sewer mains, and accelerated construction schedule.Pile design included global slope stability analyses and lateral pile analyses using several loading configurations to optimize pile geometry and spacing, and determine a value-engineered design satisfying both serviceability and strength limit states to achieve long-term stability with factor of safety of 1.3. Soils within the active landslide plane were assumed to provide no resistance, while soils below the failure plane provided lateral resistance. This stabilization scheme, which extended along the 1700-foot roadway section and toe of hillside slope area, consisted of 410 steel HP16x141 piles in two to three rows driven to depths between 60 and 70 feet below the Marlboro Clay stratum at 5 to 7-foot spacing."

Jan 1, 2017

By D. Millgard

Dennis Millgard introduced the Session by hoping that participants to the Conference would also share their piling problems. He then invited the first speaker to present his paper. Paper 5.1. Pat Kelleher commenced by saying that he belonged to a one hundred year old firm that had experience in the New York Harbour area. They were often asked to assess the integrity of many waterside structures such as piers, walls, and docks which were deteriorating whilst still in use. The earliest structures, built in the 1800's, were on timber piles. These have now changed to Steel H and tube piles and concrete piles. Usually they were called in when the structure was showing signs of distress, or had reached the end of its life but could not be closed. In particular, they had found that marine borers had returned to New York Harbour because of the improved quality of the water. There is now a far greater incidence of attack on the timber piles than when the water was polluted. Repair is usually carried out by encapsulating the pile within the tidal range of about -2ft to +8ft (-0.6 to +2.4m). Reinforced concrete forms, reinforced fibre jackets, or nylon bags are used. Reinforced fibre jackets are used with a protective coat on the pile, while nylon bags prove the cheapest method.

Jan 1, 1991

By Sylvia S. Eskander, Sherif S. AbdelSalam, Mona B. Anwar

Expanded Polystyrene (EPS) geofoam has long been used in numerous geotechnical applications due to its lightweight and durability. Among these applications is the use of EPS as an alternative fill material to conventional roadway soil embankments. This study investigates the benefits of using EPS roadway embankments to reduce the induced stresses and strains on the underlying peat and soft clay. Firstly, mechanical and interface properties of the EPS were acquired from a companion study that also considered the cyclic loading and creep effects. In order to determine the actual stress-strain distribution within the EPS blocks, a physical prototype was developed in this study with overall dimensions of 1.2 x 1.0 x 0.5 m, with a density of 35 kg/m3. The prototype EPS blocks were subjected to cyclic loading with intensities ranging from 10 to 50 kN. Then, a numerical model was developed to simulate the behavior of EPS roadway embankments. The numerical model outcomes were verified against the prototype measurements. A parametric design study was also conducted to develop a correlation between EPS embankment height and the stress-strain that occur in the underlying strata. Results showed that EPS embankments could reduce stress and settlement in the underlying soil by about 40% and 54%, respectively. EPS APPLICATIONS AND BACKGROUND Expanded Polystyrene (EPS) geofoam blocks have been effectively used during the past several decades in numerous geotechnical applications. EPS static and dynamic properties as well as interface behavior were extensively characterized in various published studies such as that conducted by Horvath, 1994; Stark et al., 2004; Zarnani and Bathurst, 2008; Trandafir et al., 2010; Athanasopoulos et al., 2012; AbdelSalam and Azzam, 2016; and others. However, to be able to use locally produced EPS blocks, its physical and mechanical properties must be thoroughly determined. The lightweight and compressible material of EPS geofoam makes it suitable both as a backfill and for absorbing pressure in both the vertical and horizontal directions. Kim et al. (2010) adopted EPS as an alternative for soil backfill around buried pipes; their model showed a reduction in the vertical stress acting on the pipes by up to 36%. Oshati et al. (2012) presented a case study of a field-instrumented box culvert with EPS blocks on top, which reduced vertical stress by 58%. Meguid et al. (2017) used an EPS inclusion to surround culverts and achieved up to 72% stress reduction, depending on the EPS density and the culvert depth to width ratio. AbdelSalam et al. (2017) used a relatively thin EPS inclusion behind flexible cantilever retaining walls, verifying that the lateral pressure can be significantly reduced by 25%; they also developed a design chart for this application. Moreover, AbdelSalam et al. (2019) investigated the use of EPS as a lightweight alternative for soil backfill above shallow tunnels. It was found that EPS had created a differential movement between the wedge located above the tunnel and the neighboring soils, which accordingly reduced the vertical stress acting on the tunnel by 85%, due to the use of lightweight EPS material and positive soil arching.

Jan 1, 2019

By Ralphie Adams, Tiana Rasmussen, Ashley E. Shirer

Transmission line foundation designers must rely on limited subsurface information, from easily accessible locations, resulting in subsurface uncertainty, increased design risk and increased construction costs. This paper presents a different approach for foundation analysis conducted in mountainous and alluvial floodplains located northwest of Phoenix, AZ. The region is dominated by fault-bounded, northeast dipping mountain ranges, where rock types and drillability can vary from granite to intact basalt. The valleys between are comprised of “basin-fill” deposits ranging from conglomerates and cemented soils to lose alluvium. Recently deposited alluvial fills can vary in depth significantly from location to location due to erosion and deposition from active and historic hydraulic features. To limit the subsurface uncertainty for foundation design, a phased approach using geophysical surveys along with detailed geologic reconnaissance was employed. Both compression wave and shear wave velocities were measured in order to identify the depth and properties of loose erodible materials from more scourresistant cemented, conglomerate, and rock deposits. These analyses were used in combination with limited subsurface drilling and sampling to evaluate direct embedment steel pole foundations for over fifty structures. Post analysis results from limited construction drilling reports were used to assess this approach.

Sep 8, 2021

By Diane Reid, Antonio Marinucci, Robin Mao

Super Cells are an innovative, open-shaped bi-directional static load testing device used to promote concrete flow during placement while utilizing greater cross-sectional area of the pile to achieve large applied axial loads at relatively low hydraulic pressures (≤ 250 bar). This paper describes the results of multi-level load testing performed on a sacrificial drilled shaft that was 3.8 m (12.7 ft) in diameter and 110.6 m (363 ft) in length for the Jiaxing-Shaoxing River Crossing Bridge that spans Hangzhou Bay in Shaoxing, China. The test shaft was instrumented with embedded strain gauges and telltale rods along with displacement transducers at the top of the pile to measure the load-induced displacements along the length of the shaft. Load testing was performed twice using a Super Cell placed near the tip of the shaft, prior and subsequent to tip post-grouting, and then again using a Super Cell placed higher in the shaft. The axial resistance for the tested conventional drilled shaft was more than 5 times greater than the estimated axial resistance. In addition, the axial resistance after tip post-grouting (347,100 kN (39,033 ton)) was about 5.3% greater than the ungrouted axial resistance (329,600 kN (37,050 ton)). INTRODUCTION During the past few decades, the magnitude of axial, lateral, and flexural loading has considerably increased due to updated design codes, larger superstructures, and the manner in which extreme event loading (e.g. seismic and scour) is incorporated into design. The diameter and depths to which bored piles or drilled shafts are constructed have increased considerably during the last three decades due to the advancements in equipment technology and capabilities. In addition, monoshaft foundations have become increasingly used, as one large drilled shaft is able to replace a group of smaller diameter piles connected by a cap. Correspondingly, adequate strata, for both side and end resistance, must be discovered/determined as well as achievable to be able to construct the required foundations to support the greater design demands. As design demands have increased, the need to ensure integrity, quality, and performance of a constructed drilled shaft has become ever more crucial. Load tests are essential to validate design assumptions of side and end resistances, to assess the behavior and load transfer characteristics of the constructed drilled shafts, and to evaluate construction methods. Load tests utilizing a bi-directional static load testing (BDSLT) device can achieve considerably large applied axial loads and can be performed more economically, in less time, and in a much safer manner than conventional top-down static load testing methods.

Jan 1, 2019