Search Documents

By Robert Jakiel

The following paper is being presented to provide an understanding of the Deep Soil-Cement Mixing (DMM) performed at Contract C09A7 at the Fort Point Channel Site (FPC), for the I-90/I-93 Interchange of the Central Artery/Tunnel Project (CA/T), Boston, MA. The paper is written as a summary of the DMM from the DMM Contractor's perspective. The summary provides technical information and practical observations that are currently considered to be state-of-the art knowledge within the soil mixing industry. The observations and information are being provided by Robert L. Jakiel, Chief Engineer of SMW Seiko, Inc., who was the DMM Project Manager and Project Engineer for the A7 Joint Venture at FPC. The DMM was started in April of 1996 and completed in December 1999. The various acronyms and terminology used to describe the soil mixing are found in a section at the end of the paper.

Jan 1, 2000

By Chris Leach, Lucie Spencer

This case study describes the geotechnical aspects of the basement construction for a multi-storey, residential and hotel complex located in the newly developed Elizabeth Quay precinct in Perth, Western Australia. The development included a three-level basement for car parking covering the full site area which was constructed using the top-down construction sequence. Soil conditions generally comprised 2m of fill overlying medium to dense clayey sands that in turn were generally overlying a very stiff clay stratum at approximately 13m depth. Bedrock level was generally encountered at approximately 22m to 35m below ground level. The ground water table was at a depth of approximately 1m below the existing ground surface level. A site boundary basement wall was constructed using a diaphragm wall retention system. The majority of the vertical loads from the building were transferred to the Kings Park Formation (KPF) bedrock through the use of foundation piles constructed by the CFA method. The CFA piles were installed from existing ground level, resulting in approximately 9m sacrificial concrete length from pile platform level to basement 3 (B3) level. The permanent column loads are such that a single CFA pile was not structurally adequate. To allow a full CFA foundation system to be adopted, an innovative design and construction approach was developed for these heavily loaded columns. This paper discusses the site technical details and the design and construction aspects required to meet the challenges offered by this project.

Nov 1, 2022

By Shawna Munn, Jakub Hudler

This paper outlines the use of tunneling headwall softeyes for transit construction projects in the Greater Toronto Area (GTA) over the past decade. Due to spatial constraints, tunnel boring machines were used to construct the underground tunnels requiring the design of launch and exit shafts with headwall softeyes to facilitate tunneling operations. Variable ground conditions and shaft geometries lead to the development of innovative headwall and tunnel softeye design applications using fiber reinforced polymer (FRP) elements (beams, reinforcing bars, and tiebacks). This paper outlines the challenges and benefits associated with designing and constructing shafts using various systems. Lessons learned throughout design and construction of more than 20 structures over the past 10 years are outlined. The constructability challenges with using FRP and design performance are also discussed. For over a decade, the City of Toronto has been expanding its metropolitan transit network with a variety of new transit construction projects. Two recent projects in the Greater Toronto Area (GTA) for underground infrastructure include the Toronto York Spadina Subway Extension and the Eglinton Crosstown Light Rail Transit project. These add a total of 31 new stations and 18.6 km (11.5 miles) of underground transit (TTC 2017) (EllisDon 2016). Due to ground conditions and spatial constraints of existing surface infrastructure, these projects utilized tunnel boring machines (TBMs) to construct the underground tunnels requiring the design of various types of shafts and headwalls to facilitate underground tunneling operations. To allow for tunneling through the headwalls, these shafts were designed with “softeyes” - a section of the wall without metal reinforcement that allows the TBMs to tunnel through.

Jan 1, 2018

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface. Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone."

Jan 1, 2017

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface.Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone"

Jan 1, 2017

By Tsuda Wakaki, Naoki Takahashi, Natsuki Okuno, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"Deep mixing (DM) method has been increasingly employed as a countermeasure against subsoil liquefaction in recent years. Pile-type DM, however, is considered to have little effect as a liquefaction countermeasure, because the shear deformation of unimproved soil around the piles cannot be reduced. However, experimental results, which imply that shear deformation of unimproved soil around DM piles can be reduced, were reported. Furthermore, a new plane-arrangement of DM piles has been proposed to mitigate lateral flow induced by liquefaction. The DM piles in this arrangement confront the lateral flow in any direction, compared with the piles arranged in conventional pattern such as square and triangular arrangements. In this study, a series of dynamic centrifuge model tests was conducted to verify the lateral flow resistance of DM plies in the new arrangement. The results indicate that the DM plies can reduce the lateral flow of liquefied ground when the pile displacement and the pile head rotation are restricted. In addition, lateral load acting on DM pile from liquefied ground, which is required for design strength of the DM pile, was investigated.INTRODUCTIONDeep mixing (DM) method has been increasingly employed as a countermeasure against subsoil liquefaction in recent years. The solidified body formed by the deep mixing method is usually block or lattice shape, composed of solidified columns that overlap each other horizontally. Lattice-type solidification has been shown to be effective as a liquefaction countermeasure despite the presence of unimproved soil inside the lattice wall, because the shear deformation of the interior soil is restrained by the wall (Suzuki et al., 1989). On the other hand, it has been thought that pile-type DM cannot reduce shear deformation of unimproved soil around the piles, because the displacement of the pile is less restricted than that of the lattice wall. DM piles have been reported to have little effect as a liquefaction countermeasure, but to be superior in terms of construction cost and applicability around existing underground structures (Koga et al., 1986). However, there are experimental results implying that DM piles have reduced the shear deformation of unimproved soil and mitigated its liquefaction (Yasuda et al., 2003; Tanaka et al., 2003). Yamamoto et al. (2006) conducted dynamic analyses of ground improved with lattice- and pile-type DM. Their results showed that pile-type DM with an improvement ratio of more than 35% reduces excess pore water pressure generated by earthquakes. Furthermore, the new pile arrangement shown in Fig. 1(a) has been proposed to mitigate lateral flow induced by liquefaction. It was developed and has been verified using dynamic model testing in a 1 g field (Takahashi et al., 2010a; 2010b; 2013; Towhata et al., 2010, Morikawa et al., 2014). The DM piles in this configuration interrupt lateral flow in any direction, unlike those placed in square and triangular arrangements."

Jan 1, 2015

Jan 1, 2000

By M. Hesham El Naggar, Osama F. E. Drbe

"Abstract: The use of micropiles has greatly increased the last twenty years, including applications involving low capacity micropile networks, seismic retrofitting, underpinning of existing foundations and high capacity foundations for new structures. This paper presents a field study of the behaviour of single hollow core micropiles in firm to stiff lean clay. Eight micropiles were installed using hollow bars (76 mm OD and 48 mm ID) with air/water flushing technique and advanced to a depth of 5.75m: six micropiles were installed using 228 mm (9 in) drill bit and two micropiles were installed using 178 mm (7 in) drill bit. All micropiles were instrumented with linear potentiometers to measure the vertical displacement of the micropile head and vibrating wire strain gauges to measure the axial strain at three points along the micropile length. Twelve full scale tests were conducted on the eight micropiles, four monotonic compression, four cyclic compression and four tension tests. Only the results of micropiles tested under monotonic compression is presented in this paper. The full scale load tests and a comparison of the performance of the micropiles with 228 mm and 178 mm drill bit are presented and discussed in terms of load-displacement curves, bond strength and tip resistance. The results showed that the proposed values of bond strength in FHWA give a conservative design of the hollow core micropiles. The micropiles constructed with 228 mm drill bit performed marginallybetter than the micropile with 178 mm drill bit in terms of the ultimate capacity.IntroductionMicropiles have been defined in a variety of ways, but can universally be classified as small diameter (less than 300mm), bored, and grouted in place piles (FHWA, 2005; Bruce et al., 1999; and Scherer et al., 1996). They can sustain axial (compression and tension) and/or lateral loads. Dr. Fernando Lizzi used micropiles in 1952 for underpinning of historic buildings damaged during World War II (Bruce D. A., 1988). Since then, micropile applications have expanded rapidly to include underpinning for existing foundations, in situ reinforcement, and seismic retrofitting and foundations for new construction. In particular, micropiles have graduated from use in low-capacity micropile networks toapplications as single high-capacity foundation.Micropiles capacity is affected by the construction technique, which involves drilling, placing reinforcement, and placing or pressurizing the grout. For example, the drilling method influences the degree of bonding between the grout and the ground, and the placement of reinforcement and the choice of grouting method have an impact on the development of the bonding. Bruce et al. (1997) showed that grout/ground bond is most affected by the grouting method. Based on the type of pressure applied during the grouting process, micropiles are classified as follows (FHWA, 2005): Type A: grout is placed under gravity pressure only using either sand-cement mortars or neat cement grout. Type B: pressures typically in the range of 0.5 MPa to 1 MPa are applied in order to inject the neat cement grout into the drilled hole while the temporary drill casing is withdrawn. Type C: involves two-step process; neat cement grout is first placed in the hole under gravity pressure head only as in type A, and prior to the hardening of this primary grout, a similar grout is then injected via a preplaced sleeved grout pipe at a pressure of at least 1 MPa. Type D: like type C, this type is a twostep process: neat cement grout is placed in the hole under gravity pressure head only (but pressure could be applied in some cases), additional grout is injected via a sleeved grout pipe at a pressure of 2 MPa to 8 MPa once the primary grout has hardened. In some cases, a packer is used inside the sleeved pipe, enabling specific horizons to be treated. Recently, Type E micropile is proposed, which involves"

Jan 1, 2014

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By J. Hartikainen

Kemi cardboard mill is founded on the alluvial bed of Kemi river at the north-eastern cost of Botnic Culf in Northern Finland. The alluvium consists of sandy and silty layers underlain by thick medium dense silty moraine layer. The first cardboard machine, having a belt width of 7,4 m, was constructed in 1972 on 7,5 to 9,5 m long wedge-shaped precast driven piles. Because of the excessive differential settlements and sometimes unexpected dynamic malfunctioning of the machine it was decided to strengthen the foundation before installing the partly new machine and increasing the running speed from 500 to 750 m/min. Piling was done under extremly strick limitations concerning space, vibrations, settlements, dust etc. Extra vertical support was made by using 23...25 long x-form steel piles driven by compressed air pile hammer down to rock. The piles were held together with old piles by a conctrete frame with diagonals, which made the total system - machine - foundation frame, piles and ground - ridgid enough to avoid resonance during dynamic loading.

Jan 1, 2010

By Leonhard Weixler, Alexander Blatt, Franz-Werner Gerressen

Diaphragm wall technique is usually used to construct structural elements in the ground, commonly used for retention systems, permanent foundation elements or deep ground-water barriers, named Cut-Off-Walls (COW). It can be anticipated that global urbanization and increasing demands on environmental considerations will need to be accommodated in underground space in the future. These trends show an increasing requirement for diaphragm walling in even more complex conditions, especially in inner-city applications with limited space. Therefore, there is the demand to minimize the size of equipment to accommodate such projects. Following this demand, a new trench cutter system, the so-called CUBE System, was recently developed. The complete trench cutter system has been fit into container size dimensions so that it can work in very limited space conditions. In addition, complex conditions in terms of space limitations require specifically adapted solutions for slurry, spoil, reinforcement and concrete handling and the related logistics to ensure smooth production. Due to the limited space requirements, the impact on the surrounding environment is limited. As the system is electric driven, an additional reduction of carbon footprint can be expected. First tests of the system have been carried out and the results will be shared. The paper will explain the construction process and the specific challenges and experiences made for these extreme conditions.

Oct 1, 2022

By Zhitao Ma

The Cast-in-place Concrete thin-wall Pipe pile, referred to as PCC pile, is a new kind of pile for soft ground improvement. In this paper, firstly, the general introductions of the new pile technique, mainly including the technique principle, the structure of pile-driving machine, and the technological process were given, then based on the results of in-situ static lateral loading test, the pile lateral capacity, the relationship of load-deflection of pile at the ground surface, the lateral deflections versus depth and the soil reaction along the pile shaft were analyzed.

Jan 1, 2006

By Richard J. Finno

Detailed measurements made at a test section adjacent to a deep braced cut and other published data are combined to illustrate the limitations of the common methods of predicting movements associated with excavations in soft to medium clay. While past performance data can be used to estimate expected responses before construction in many cases, actual wall and soil deformations throughout construction can only be estimated using finite element procedures. Success of such analyses depends equally upon considering all aspects of construction that induce strains in adjacent soil, such as wall installation, excavation and bracing sequence, and time, and adequately modeling soil stress-strain behavior. Even when these two criteria are met, soil deformations can not be predicted adequately when strain levels exceed those that produce peak shear stress.

Jan 1, 1991

By Mark R. Svinkin

Regulations are needed to keep construction vibrations in tolerable limits. The existing regulations were developed for low-rise residential structures, but they are incorrectly used for different super and underground structures. The existing regulations cannot prevent most of harmful vibration effects on sensitive devices, people and structures from construction and industrial vibration sources. It is important to determine the areas of application of the existing regulations and bring attention to the necessity of measurement of the structural responses for assessment of vibration effects on structures. For multi-story residential, commercial and industrial buildings, the frequency-independent safe limit of 51 mm/s (2 in./s) can be chosen for the peak particle velocity of structural, not ground, vibrations. Specifications for construction operations with dynamic sources have to consider specifics of each construction site. Preventive measures can be used to mitigate harmful vibration effects on various structures and settlements in sand and clay soils.

Jan 1, 2006

By Sridhar Krishnan

This paper presents the results of a comprehensive pre-production pile testing programme for the US$ 800 million 1400MW Coal-Fired Jimah Power Plant Project in Negeri Sembilan, Malaysia. The testing programme included high-strain dynamic testing and fully instrumented static axial and lateral load testing of driven prestressed concrete piles and bored cast-in-place piles. A highlight of the testing programme was the pioneering use of the Global Strain Extensometer (GloStrExt) Method, a deformation monitoring system that uses advanced pneumatically- or hydraulically-anchored extensometers and a novel analytical technique to monitor loads and displacements down the shaft and at the toe of driven prestressed concrete piles. The experience with the testing programme for the Jimah Project also demonstrates the possibility of achieving notable breakthroughs, not only in the monitoring, evaluation and reporting of pile foundation behaviour dynamics but also in our understanding of the mechanisms that underpin such behaviour. These significant gains are undeniably a direct result of the committed and co-operative relationship among the project owner, design/builder, specialist piling subcontractors, pile suppliers and pile instrumentation and testing specialists.

Jan 1, 2006

By Seung-hoon Lee

The use of piled raft foundations has been considered as an economical alternative to conventional piled foundations because a portion of the applied load is carried by the raft in the design of piled raft foundation. In analyzing the behavior of a piled raft foundation as a settlement reducer, an accurate estimate of settlements of the system should be made on the basis of the understanding of nonlinear behavior of piles in layered soils as well as the interaction between the raft, soils, and piles. Although the 3-dimensional finite element method and simplified analysis methods have been used for the design of piled raft foundations, these methods were found to be inadequate for the practical purpose or could not consider the interactions properly. This study developed an approximate hybrid method of analysis to be used for the practical design of piled raft foundations considering pile-soil, raft-soil, pile-soil-pile and raft-soil-pile interactions. In the presented method of analysis, the settlements of the system are estimated satisfying the compatibility of two separate models which are the flexible raft model consisting of 2-dimensional finite elements supported by springs representing soils and piles, and the group-pile model embedded in layers of soil having different properties. Comparisons with other analytical methods as well as a 3-dimensional FEM program were made to verify the sufficient capabilities of the proposed hybrid model for application to practical design and analysis of piled raft foundations.

Jan 1, 2008

By Abolfazl Eslami, Samieh Rezazadeh

"Semi-Deep skirted foundations are considered to be a viable option for a variety of onshore and offshore applications. It is necessary to determine appropriate foundation configurations that allow loads to be transferred safely to the surrounding soil. For this purpose the bearing capacity and stability analyses subjected to combined vertical, horizontal and moment loadings must be found. In this paper the vertical undrained bearing capacity is estimated via finite element analyses. The circular skirted foundations with different geometries considering embedment depth (embedment ratio between 0-2) and size effects (diameter equals to 5, 10, and 20) have been studied. Stress field, kinematic mechanism accompanying failure and bearing capacity factors for total, end and shaft resistance in semi-deep foundations with various embedment ratios are investigated. Furthermore, two probable mechanisms i.e. internal flow and soil plug for estimating foundation capacity for design purpose in practice have been assessed. Comparisons with different research works including conventional methods, upper and lower bound approaches, and finite element analyses have indicated that the conventional methods underestimate the bearing capacity due to ignoring the significant role of shaft resistance. Determining appropriate economic foundation configurations to transfer loads safely to the surrounding soil is a major issue in geotechnical engineering. Shape and dimension of foundations, embedment depth, soil characteristics and applied loading, all affect the foundation performance. Recent studies have shown that for foundations with large breadth and of D/B between 1 to 4, kinematic mechanisms and failure modes are different from the two main types of foundation (i.e. shallow and deep). Therefore, D/B factor must not be considered as the only factor for defining foundation type. ""Semi-Deep foundations"" are another foundation category distinguished based on their performance. This relatively new concept is becoming increasingly an optimum alternative for shallow and deep foundations to support structures especially in accessible depth. As illustrated in ""Fig. 1"", different types of semi-deep foundations consist of:"

Jan 1, 2017

By Howard Roscoe

Linking Ashford International Station to the new Channel Tunnel Rail Link required over 5000 rotary bored and CFA (continuous flight auger) piles to form tunnel walls and viaduct foundations and to support overbridges and trackside barriers.. Much of the work was carried out close to the existing railway infrastructure. Plunged columns were used to maintain traffic flows over the tunnel site during construction. The results of an extensive programme of vertical and lateral load tests on bored and CFA piles in heavily overconsolidated Weald Clay are compared to illustrate the relative importance of stress relief and of prolonged exposure to bentonite. The completion on schedule of this major piling and ground engineering contract (value £30 million) demonstrates that collaborative working in partnership produced cost effective solutions to a series of challenging technical and logistical problems.

Jan 1, 2002

By J. Tanner Blackburn, James R. Gingery, Lisheng Shao

Rigid inclusions consist of grout columns installed using displacement auger or vibrated tooling. The columns are typically installed in an array to provide support for footings, mats, or embankments. Due to the relative small column diameter and low replacement ratio, the surrounding soils typically have minimal densification or improvement. A gravel load transfer platform is commonly used above the rigid inclusion head to distribute stresses more broadly to the supported structure. The axial stiffness and geotechnical engineering mechanics of rigid inclusion design are similar to those of deep foundation systems, but they are typically only lightly- or un-reinforced and are not structurally connected to the above-grade structure. The popularity of rigid inclusions is increasing in the Western U.S., where many urban areas are subject to moderate to high seismic hazard levels. However, the performance of rigid inclusions under seismic loading is poorly understood, and seldom addressed in current designs. The elements are brittle, with limited or no ductility and relatively low moment capacity, and therefore may be prone to damage under seismic loading. Three modes of seismic loading should be considered: inertial loading from the structure, kinematic loading from vertically propagating shear waves, and kinematic loading from ground failure- related permanent ground deformation. This paper focuses on the first two modes. A simplified procedure for evaluating kinematic and inertial loading of rigid inclusions is described, and its use is illustrated through application to a site in Southern California. The results show that moderate to severe kinematic loading can generate plastic hinges in the rigid inclusions. Engineering consequences of this hinging could include settlement or bearing failure. INTRODUCTION In this paper the term ‘rigid inclusion’ (RI) refers to grout or grouted aggregate columns that are installed using either drilled or vibration displacement techniques. They are commonly installed in arrays to support vertical loads from footings, mats, or embankments. RIs are not structurally connected to footings they support. Rather, it is typical for a dense gravel load transfer platform (LTP) to be installed as a cushion between the RI head and supported footing or new fill. In cases of RI support of fill embankments, the LTP may be reinforced with horizontal layers of geogrid.

Jan 1, 2018

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006