Search Documents

By Juhyung Lee

Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.

By Madhira R. Madhav

In an alluvial deposit consisting of layers of sandy silt with clay and kankar nodules, driven cast in situ piles are provided. The piles end on a stiff bearing stratum To verify the available design capacities, compression, pull-out and lateral load tests are conducted in situ. The elastic continuum approach is used to estimate the equivalent modulus of deformation of the deposit. A comparison is made of the values from the three types of tests.

Jan 1, 1996

By J. S. Ward

In a well-written set of contract documents, the probability of conflicts arising during the course of construction is minimized. However, no matter how complete may be the technical language in the contract plans and specifications, the possibility always exists that conditions may be found in the field that were not anticipated at the time the design was formulated. In foundation engineering work, this is commonly referred to as "differing site conditions." When such a conflict arises in the field, the most expedient manner of resolution would be for the parties to the contract to meet and to amicably resolve the issues rather than use the long and costly adversarial approach of the litigation system currently prevalent in the United States. This rapid solution to the construction conflict can be accomplished through an alternate dispute resolution technique that includes mandatory discussion, mediation and arbitration to be initiated immediately following the inception of the dispute and to be concluded in not more than 100 calendar days from the time the dispute originated.

Jan 1, 2010

By G. X. Zeng

A calculation programme of finite element method has been developed in order to study the behavior of excavation with sheet piling in soft clay. Based on a series of isotropically consolidated-undrained tests (CIU) on Hangzhou clay a linear relationship between the normalized initial tangent modulus number, E1, and stress-path parameter, a, is found for four different stress paths, and stress-path dependent modulus equations derived. Meanwhile, several influence factors, such as embedment depth and stiffness of the wall and soil conditions, were taken into consideration in the programme. Some valuable conclusions were obtained. Finally, a case history was studied by the proposed method of calculation. The result of calculation and the field observation are in good agreement.

Jan 1, 2010

By Francis D. Leathers

Four friction pile load test programs, including 23 tension tests and 9 compression tests, have been performed as part of the Central Artery/Tunnel Project in Boston, Massachusetts. The tests, performed on both precast, prestressed concrete (PPC) piles and steel piles, yielded the following adhesion values: [Soil Type Clay Clay Glacial Till Interbedded Sand and Clay Interbedded Sand and Clay Pile Type PPC Steel Steel Steel PPC Adhesion (psf) 610 to 1,200 230 to 900 220 to 550 680 1,280 ] The adhesion appears to be affected by differences in pile material type, with PPC piles having higher adhesion than steel piles. However, part of the apparent difference for the clay may be due to differences in time between driving and testing. The significant range of test data means that the need for site specific testing to determine or verify design values of adhesion should be considered during design. Creep rates at loads near failure ranged from about 0.02 to 0.18 inches per log cycle of time, with most values in the range of about 0.04 to 0.08 inches per log cycle of time.

Jan 1, 1994

By Andrew Cushing

This paper presents the design and construction of the foundation for a major high-rise real estate development on the west side of Manhattan. Arup was retained by Underpinning and Foundation Skanska to design a secant pile wall as excavation support for a proposed two-level basement of a new 23-story residential building located at 100 11th Avenue and West 19th Street. The secant pile wall will also act as the permanent basement retaining wall for the new building. The site is bounded on two sides by existing structures and is underlain by a thick deposit of very soft organic silt and clay. Therefore, the potential for ground movements and their impact on an adjacent structure bearing on shallow footings were of the utmost concern. This paper addresses the design and construction considerations associated with this secant wall, as well as installation details. Measured wall movements are also used to assess the validity of the pre-construction soil strength and stiffness design parameters.

Jan 1, 2008

By Alain Pecker

The choice of a design concept for a bridge foundation is guided by various factors; several of these factors are indeed of technical origin, like the environmental conditions in a broad sense, but others non technical factors may also have a profound impact on the final design concept. The foundations solutions adopted for the Rion Antirion bridge are described and an attempt is made to pinpoint the major factors that have guided the final choices. The Rion Antirion bridge is exemplar in that respect: the foundation concept combines the simplicity of capacity design, the conceptual facility of construction and enhances the foundation safety. The design of these foundations was a very challenging task which required full cooperation and close interaction with all the parties involved: concessionaire, contractor, designers and design checker.

Jan 1, 2013

By D. Mohan

Soft to medium dense silty and clayey soils are found in many parts of India and conventional friction piles have normally been used for foundations of high rise buildings and other structures on such soils. The author investigated the use of Bored Compaction Piles and these have been used on these soils achieving substantial economies in cost over conventional friction piles. Similarly highly expansive clays, commonly known as Indian Black Cotton Soils occupy about 20 percent of the Indian land area. Short bored underreamed piles have been developed for such soils and a very large construction of various types of buildings and other structures have come up on such piles over the last thirty years in various parts of the country. The paper describes investigations leading to the design and development of both these type of foundations.

Jan 1, 1989

By J. Matos e Silva

"Abstract The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the ones obtained by using the Eurocode 7 and the Portuguese Norm related to the EC7 (NP EN 1997-1 2010), as the Eurocodes consider the possibility of each European country to adopt their own geotechnical parameters as these may vary from one country to another. A comparison is also made with the behaviour of these diaphragm walls during its construction phase; so the values from the design that were adopted in the construction are listed in tables 2 to 6 in the “Construction Options” columns. From the referred examples the author presents his conclusions.1 - INTRODUCTIONIn the so-called “traditional criteria” the soil parameters (dry unit weight, angle of internal friction and cohesion) have values obtained through tests or empirically. It is assumed that the characteristic values of the soil parameters adopted in Eurocode 7 are equal to the soil parameters adopted in the calculations by the “traditional criteria”. In the present paper the design according to the EC7 was made considering only the ultimate limit states and the respective Cases A1 and A2.The partial coefficients used for the actions in the present paper were those on Table 1:2 - CONSIDERED EXAMPLESThe five examples correspond to the situations of figures 1 to 5, and the respective results are summarized in tables 2 to 6.For all the considered examples, that are case histories, a simplified method published by Matos e Silva (March 2000) was adopted. This method attains good performances when compared with other more sophisticated ones as the finite elements and the elasto-plastic methods as described in a paper published by Matos e Silva (2000). All the obtained values were compared between them and with the so-called “Construction Options” that were the values adopted by the designers of the considered examples. For the wall bottom length calculation two possible situations were envisaged:"

Jan 1, 2014

By Eric S. Lindquist

High groundwater levels combined with variable soil and rock profiles present challenges to the design and construction of deep excavation support systems. Increasingly, secant piling techniques are the preferred technical solution for shoring in these cases. Recent developments in drilling equipment, tooling and procedures allow cost-effective construction of deep, overlapped pile systems to tight tolerances in extremely difficult ground conditions. This paper summarizes critical design considerations for secant pile shoring systems, detailing recent advances in installation procedures and verification techniques that allow secant piles to be used for an expanding range of project conditions. Technically- and commercially-viable secant pile shoring designs require that stringent drilling tolerances be achieved in order to successfully provide combined structural support and groundwater cutoff systems, particularly for unreinforced circular secant pile shafts acting in ring compression. Modern drill rigs and tooling can advance fully cased shafts in geotechnical conditions which range from cohesionless soils below the groundwater table to hard rock, within a single drillhole. Down-hole instrumentation provides verification that tolerance requirements are met and allow secant pile shoring to be used at sites previously considered unacceptably risky. In California, secant pile shoring systems are being used for excavation depths of over 100 ft (30 m) on projects with challenging site conditions. Two case studies are presented detailing severe geotechnical conditions and excavation depths which represent the regional state of practice in secant piled excavation support. These projects provide real world examples of the design, construction and construction verification techniques that permit secant pile shoring to be used in more demanding geotechnical conditions and to greater depths than ever before.

Jan 1, 2011

By B. Broms

The "Bawang Pile" (in english "onion" pile) described in the article consists of a cased concrete shaft and an expanded base. The steel casing is first driven by an internal drop hammer and then the base is formed in-situ by the raming the concrete at the bottom of the slitted casing. This new type of pile can be used for underpining (small head room) of buildings and as foundation for transmission towers or lamp posts. Full-scale load tests in compression and in tension on the Bawang pile and on steel pipe piles demonstrate the dramatic increase of the ultimate capacity due to the expanded base. Guidelines for the design of such piles are proposed.

Jan 1, 2010

By Alan J. Lutenegger

A series of tension tests were performed on prototype scale steel pipe piles at two sites to evaluate the influence of scale and pile plugging on the unit skin friction developed in axial tension. The first site consisted of a clean medium dense fine sand above the water table. The second site consisted of a loose silty sand with the water table within about 0.5 m of the ground surface. Pile load tests performed at each of the sites included piles with diameters ranging from 73 mm to 114.3 mm, which may be considered driven "micropiles". At the first site, pile lengths of 6.1 m were used; at the second site, pile lengths of 9.1 m were used. Some of the piles were driven open-ended while others were fitted with a conical tip to form a closed end. During installation, pile plugging measurements were taken on the open-ended piles after each 0.30 m of penetration. The piles were allowed to rest for a period of about 30 days after driving prior to performing the axial uplift load tests to failure. The results indicate that in the medium dense fine sand the unit skin friction developed in tension is dependent on both the amount of plugging that occurs and on the size of the pile, which was not the case for the loose silty sand.

Jan 1, 2000

By D. A. Bruce

The Deep Mixing Method is a very valuable tool for combating problems related to in situ soil treatment, improvement, and retention. Many different variations are used throughout the world, and there is a correspondingly rich technical literature on the testing and properties of the treated soil. This paper provides a synopsis of these aspects.

Jan 1, 2001

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By Jean J. Abiassi

The Boston Marine Industrial Park (BMIP) VENT 6 project is a cut and cover tunnel, part of the Central Artery / Tunnel (CA/T) in the city of Boston. The BMIP job will serve as the south approach to the Third Harbor Tunnel crossing. The alignment is approximately 2500 Ft long and is made up of four sections starting from west to east: 1. West Tunnel 2. Boat Section 3. East Tunnel 4. Tunnel inside Vent 6 Cofferdam and connection to the Third Harbor Tunnel. The support of excavation (SOE) system for the West Tunnel, Boat Section, and East Tunnel are all a part of this project whereas the SOE for Tunnel inside the Vent 6 Cofferdam was a part of the contract for the Third Harbor Tunnel.

Jan 1, 1994

"The Morris Island Lighthouse (MIL) is located between the jetties leading to the Charleston Harbor and Folly Beach, S.C. The present structure is the third lighthouse to occupy this location. The first navigational aid was erected in 1673, and consisted of a raised pan filled with pitch, which was set afire at night to guide early ships. The next structure was built in 1767, and constituted the first real lighthouse, standing 42 ft (12.8 m) in height. In 1838, a second lighthouse was built on the site, and it measured 102 ft (31 m) in height and featured a revolving light. This structure lasted until 1862 when Confederate troops, during the Civil War, destroyed it to deny its use to Union troops.Navigators steered these waters without a lighthouse for nearly a decade until 1876, when the current structure was built under the direction of the U.S. Army Corps of Engineers (USACE). In 1886, the Charleston area suffered a M7.6 earthquake. Significant damage was caused throughout much of the area, including a slight “list” of the lighthouse to the northeast. As a result, the cast of the beacon was reduced from 18 mi (29 km) to about 6 mi (9.7 km), causing much distress to navigators until the beacon platform was releveled and remains at this list to the present day.Conditions for ConcernThe current lighthouse was originally constructed about 1,200 ft (366 m) from the shoreline. Over the years, USACE has undertaken several programs to meet the increased shipping and navigation demands in the Charleston Harbor. Around the turn of the last century, two jetties were constructed, which drastically changed the approach direction for ships entering the harbor. In subsequent years, the harbor began to experience accelerated siltation."

Jan 1, 2017

By RAP Bement

Installation by vibrodrivers of sheet and bearing piles generates periodic vibrations in the surrounding ground, which have been widely measured and reported. One of the possible consequential effects of these vibrations is ground settlement caused by the compaction of loose granular soils. Vibratory compaction settlement of a range of granular soils has been studied in the laboratory using a 150mm diameter Rowe cell, which allows sample preparation and control during vibrations equivalent to conditions in the field during vibrodriving. The cell containing the soil sample was mounted on an electromagnetic shaker and vibrated at amplitudes and frequencies appropriate for soils adjacent to vibrodrivers. The changes in sample height were recorded.

Jan 1, 1996

By Matthew Janes

The installation of piles and casings is becoming increasingly difficult as restrictions on vibration become common in major urban areas. The use of high frequency, resonant excitation of a pile or casing permits ease of installation of sections to great depths with near imperceptible vibrations as close as 1 pile diameter. The new Resonant Driver is able to excite a pile at its resonant frequency (up to 150 Hz or 9000 VPM) to produce elevated levels of acceleration, force and displacement in the pile. The combination of extremely high acceleration and controlled levels of displacement allow the pile to slice through varied soil with almost no vibration translated into the ground. In direct comparisons between conventional vibrators and impact hammers the Resonant Driver produces less than 1/50th the vibration. The Resonant Driver results in ground vibration of between 1/20 and 1/40 of common limit levels (1 cm/s or 0.5 in/sec) as close as 1 pile diameter. At a distance of 5 m (16 ft) from the pile or casing vibration levels approach imperceptible levels. The Resonant Driver uses a proprietary algorithm to tune the drive vibration to the changing natural frequency of the pile as it is driven into the ground. By maintaining resonance the energy in the pile is built up like in a flywheel on an engine or a child on a swing. This build up of energy aids in driving and significantly reduces waste. Recent experience using the Resonant Driver is proving the technology can drive a variety of steel pile and casing sections through varied soils. Continued use of the Resonant Driver will create a data base of various pile and casing sections, soil types and achieved capacities.

Jan 1, 2008

By William Siegel

Kleinfelder provided foundation analysis and design for an expansion to a cement plant in Florence, Colorado. The expansion was a conversion from a horizontal wet process to a vertical dry process, and resulted in the construction of a number of structures with heavy foundation loads. [ ] The field investigation identified old fill and saturated sands and gravels above a shale/limestone bedrock environment. Based upon the anticipated loading, drilled piers socketed into bedrock were recommended. The structures were constructed in accordance with the design recommendations.

Jan 1, 2007

By Mostafa Mossaad, Ali Helwa, Manal Salem

Support of excavation (SOE) design practice tends to model SOE elements using two-dimensional (2D) analyses to avoid the complexity associated with three-dimensional (3D) analyses. Such practice overlooks soil arching in the horizontal plane and prevents designers from accounting for elements such as capping beams as part of the statical system. This study simulates square excavations supported by cantilever slurry walls in dry cohesionless soil using 2D and 3D finite element (FE) models. First, side support wall behavior is compared from 2D and 3D FE models for variable excavation length to depth (L/H) ratios. Second, the effect of slurry wall lateral bending stiffness on wall behavior is studied by modeling the wall using plate element with isotropic and anisotropic wall stiffness. Finally, the sensitivity of cantilever wall behavior to the presence of capping beam is illustrated. The study concludes that unbraced excavations with L/H ratios greater than 5 almost resemble plane-strain conditions. Slurry walls are better simulated in 3D FE models by dividing the plate element into discrete panels or by assigning anisotropic bending stiffness to the plate element. Finally, the presence of capping beam affects the behavior of cantilever walls resulting in reduction of deflections and redistribution of bending moments. INTRODCUTION Support of excavation (SOE) design practice ranges in complexity from conducting simple hand calculations to performing three dimensional numerical modeling depending on several factors among which is the geometry of the design problem. This paper addresses walls that are designed using numerical modeling, and discusses the factors governing the choice of the most suitable modeling approach. It has been believed for a while that modeling excavations using 2D numerical models would lead to a more conservative solution, which turned out to be incorrect in specific cases. This paper attempts to describe cases where 2D finite element modeling could be on the conservative side and other cases where it could be less conservative than the more complex 3D modeling.

Jan 1, 2018