Search Documents

By Jeffrey M. Taylor, Arturo Ressi di Cervia

"Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 foot (2.44m) diameter drilled shafts with 7.5 foot (2.31m) rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at both the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts. INTRODUCTIONThe replacement Brightman Street Bridge spans the Taunton River between Fall River and Somerset in Massachusetts.The new crossing is located approximately 1500 feet (450m) upstream from the existing Brightman Street Bridge, which was built in 1908. The new mainline bridge includes nine spans totaling 1725 feet (525m). A bascule type moveable span will be located in the middle of the Taunton River and provide a 200 foot (61m) open channel centered about the 400 foot (122m) navigational channel. The bascule span, which has a span length of 409 feet (124.7m), will be a trunnion-type four leaf structure with a solid deck. A site plan is shown in Figure 1 Contract 3, which includes construction of the foundations for the East and West bascule piers, was bid on December 19, 2000 and was awarded to Modern Continental Construction Company (MCC) on January 24, 2001. MCC in turn awarded the subcontract for the installation of the drilled shafts to TREVIICOS Corporation, which started mobilizing in June of 2001.The scope of work for the drilled shafts of Contract 3 consisted in installing 18 drilled shafts in three rows on each side of the river to support the bascule piers located in the middle of the Taunton River.The foundation plan for the bascule span is shown in Figure 2."

Jan 1, 2004

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By Martin Mcdermott, Kevin Tehansky, Robert Ross, Jeffrey Goodwin

A foundation value engineering redesign is a collaboration between the project owner, original design team, general contractor, foundation contractor and redesign team. Without the acceptance and collaborative effort of all the stakeholders, the redesign process is doomed to failure. For the addition at the Hackensack (New Jersey) University Medical Center (HUMC) we had just such a collaborative effort for the drilled shaft redesign. For a successful redesign effort, the collaboration between the foundation contractor and their redesign team needs to fully exploit the contractor’s specific equipment and experience and convey how to apply this to the project as a whole to ensure everyone is confident that the project design goals are being met. For the HUMC project, applied load testing of the drilled shafts (bi-directional and lateral) were used to provide ultimate geotechnical design values for the redesign effort. By utilizing the contractor’s preferred equipment and the redesign team’s testing and application expertise, the redesign collaboration was able to enhance a good design and make it into a great project.

By Vijaya Bhushan Rao, Jason Redgers

The typical Vibrocompaction projects undertaken in the UAE are on reclaimed Sands. These Sands which are predominantly the crushable, calcareous, carbonate sands found locally as opposed to the more common quartz or silica sands that are featured in most design literature. The famous reclamations such as the iconic Palm Jumeirah in Dubai, often have specification for mitigation of liquefaction induced settlements, bearing capacity increases and total and differential settlement requirements. Often these performance targets are achieved by the means of achieving a particular relative density that are generally measured by a defined Cone Penetration Test, CPT targeting values of cone resistance (Qc), MPa at respective depth zones. In this paper some case studies are presented, where soil suitability for deep compaction by vibratory methods was firstly assessed for suitability using the Massarsch, 1991 compactability chart prior to the application of vibrocompaction and its subsequent evaluation. One such project named the Island Development required 17 to 23m depth of penetration only to treat the lower 5 to 6m of sand above rockhead as eventually the top 15m of sand will be further excavated to allow for the construction of basement. The paper will present pre and post CPT results, the results of initial site calibration trials and evaluation of the completed works.

Oct 1, 2022

By Frank Rausche, Scott D. Webster, Rozbeh B. Moghaddam

"Pile foundation driveability is a function of several variables such as subsurface characteristics, hammer type, hammer efficiency, pile type, and plugging conditions. One important phenomenon occurring during pile driving, and yet not well documented and published, is the friction fatigue, where a reduction of shaft resistance is observed as the pile is driven to greater embedment. This paper introduces current soil models developed for the assessment of friction fatigue, and further presents a comparison between predicted driveability obtained from Wave Equation Analysis Program (GRLWEAP) and field driving records. From a literature survey, and review of technical articles, a widely-used soil model known as AH-01 has been selected to analyze the friction fatigue concept. Using a WEAP software, two driveability analysis were completed using the standard approach with setup factors, and adapting the AH-01 model into the WEAP input file. Driveability predictions were compared to the driving records corresponding to a 1676-mm x 44- mm open-ended pipe pile with a total and embedment lengths of 180-m and 119-m, respectively. Results from analyses and the comparison presented in this paper provide further information regarding existing methods for the incorporation of the friction fatigue concept to the driveability analyses, and contributes to a better prediction of driveability of open-ended pipe piles. IntroductionDynamic measurements during pile installation provide more dependable information as compared to results obtained from predictive models used for design. Despite uncertainties associated with a specific project site and foundation type, measured data provides a reliable understanding of the soil resistance and its distribution throughout the length of the pile. Back-calculations or back-analyses based on a series of measured data from a pile driving process could help to obtain reliable models to better predict events related to pile installation process in spite of all variability related to fitted models. One of the widely-used analysis regarding pile driving during the design phase is the “driveability analysis” where capacity, blowcounts, maximum stresses in the pile element, and transferred energy from the hammer to the pile element are predicted using mathematical models along with a software. Such analysis requires relevant information regarding soil, pile, and hammer properties combined with a deep understanding of the level of impact each one of these properties could have on the analysis."

Jan 1, 2017

By Benjamin B. Buensuceso III

Crosshole sonic logging (CSL) is a popular quality assurance and quality control method used to examine the concrete quality of cast-in place deep foundations, though the evaluation of the results is subject to certain limitations. One such limitation explored in this paper is the occurrence of false positives, where signal anomalies indicated by CSL test results are not necessarily indicative of imperfections in the foundation that could affect its performance. A case study of false positives evaluated in CSL records in a major infrastructure project in Metro Manila is presented in this paper. A detailed desktop evaluation and results from complementary high-strain dynamic load testing and low-strain pile integrity testing were used to evaluate the significance of the suspected false positive signal anomalies from the CSL test results. Recommendations for the proper interpretation and evaluation of CSL test results in Philippine practice, given the method’s limitations and examples presented, are also shared.

Sep 8, 2021

By Amr Sallam, David Thompson, Moataz Hassan

"The Little Lake Harris (LLH) Bridge was constructed in 1951 to replace the eastwest County Road 48 Bridge connecting the towns of Howey-in-the-Hills and Astatula in Lake County, Florida, United States. The 78-span bridge carries two lanes of traffic, is 3,130 feet long, and 36.1 feet wide. The concrete deck is supported by steel I-girders carried by one row of 18-inch square precast concrete driven pile. In the late 1980's, slight settlements were observed in several bents. In 1990, Florida Department of Transportation (FDOT) initiated annual survey of deck elevations during bridge inspections to monitor settlement. Due to the slow nature and magnitude of settlement, substructure instability was not a major concern to the department. However, public concern over the settlement and rough ride of the bridge continued to rise. FDOT contracted Kisinger Campo & Associates Corp. (KCA) to provide the needed design to correct the dips in the riding surface and minimize future settlement. KCA's initial design was based on the concept of ""helper bents"" at the settled bents in order to restore the bridge to original elevation. Estimated construction cost for seven helper bents was about $3.3M. FDOT requested evaluating other alternatives to reduce the cost of the bridge restoration. KCA involved the geotechnical consultant, Terracon Consultants, Inc. (Terracon), to perform a peer review and provide an economical alternative solution. Jacking and shimming the bridge was determined to be both technically viable and economical with a total cost of less than $300K. The design was completed in March 2010 and construction was completed in February 2011. This paper provides an overview of the LLH Bridge history, summarizes the evolution of the design methodology including the findings of the geotechnical study and presents lessons learned during the design and construction of the project.INTRODUCTIONThe Safety and Preservation of the State Highway System is the top priority of the FDOT. Therefore, FDOT initiated a bridge management program that starts with conducting biennial safety inspections performed by Certified Bridge Inspectors (CBI). The inspection reports together with the CBI’s recommendations are reviewed by a registered Professional Engineer (PE) and work orders are issued with priority ranking depending on the severity of the bridge deficiencies. If the scope of work is considered beyond the in-house crews’ capability, the work is then included in a contract for and bid. LLH Bridge was a little different. It was initiated in direct response to number of complaints the FDOT District 5 Structures Maintenance Office (D5SMO) received regarding settlement of the Little Lake Harris Bridge."

Jan 1, 2015

By David R. Beadman

This paper discusses how modern techniques of design and construction were used to create the deep stations for the Copenhagen Metro. The deep stations are located in small squares within the city adjacent to many old and sensitive buildings. The architectural design provides a large open atrium to allow natural light to reach the column free platforms to give the citizens of Copenhagen a feeling of safety and security and encourage them to use the Metro. The design and construction contract was undertaken using the relatively new and untried Eurocodes. The resulting stations set new standards of design for underground metros and have pushed forward the frontiers of what is appropriate construction practice to protect the existing and enhance the future environment.

Jan 1, 2000

By Jerold Bishop, Grant Bearss, Aleksey Egorov

"When a shock wave is released in the bottom of a drill hole filled with wet concrete slurry, the result is called an electrohydrodynamic effect, or EHDE. The energy is carried through the fluid with minimal loss because the slurry is an incompressible medium. Repetitive discharges provide a series of energy pulses that compact the soil along the pile shaft and at its base. The process is analogous to repeated applications of low-energy blast densification or to dynamic compaction. In general, the process is not depth dependent. EHDE was identified in the 18th century by an American scientist who observed that a spark between two electrodes placed under water induced a burst of pressure. In 1957, two Russian engineers formulated a process and received a patent for a method of creating a pressure wave by transforming power from an electrical discharge to a mechanical impact. They derived more than 200 applications for technical and industrial processes.In the 1970s, civil engineers at the Engineering and Building Institute in St. Petersburg, Russia, began to look at EHDE to improve the capacity of drilled piles. Early experiments showed that electric discharges in a wet concrete slurry mix could create a pressure wave of up to 26 MPa (3700 psi). Later tests demonstrated that this pressure level could be created in a drilled pile hole. The researchers devised equipment and in the early 1990s began to study pulse technology as applied to drilled piles.This application was accepted into the Russian Federation Building Code in the 1990s. The code treats “regular” drilled piles with equivalent bearing area as having roughly half the capacity of a driven pile. However, the code considers drilled piles treated with the EHDE technique a direct “one for one” substitution for driven piles and allows higher values if the capacity is established by static load testing. Hundreds of projects have been completed in Russia using this technology to value engineer drilled pile projects. In several instances, the number of drilled piles installed was fewer than half of the number originally planned for due to the capacity increase that EHDE-treated piles provided.Drilled PilesIn drilled pile construction, the EHDE process creates a mechanical pressure wave that impacts the base and sidewall of a drilled pile shaft. Soft, poorly consolidated or loose soil is compacted by successive pulses of pressure created by electrical discharges. These mechanical impulses are made by inserting a discharge probe into the wet concrete slurry. A discharge across the tip of the probe creates the pulse that travels outward to the sidewall and base of the drilled pile through the incompressible medium of the slurry. The power pack ratings for equipment presently in use are 35 and 50 kJ (kilojoule).Each pressure wave strikes the soil, causing compaction and expanding the hole. Workers apply the pulses until the size of the hole stops increasing. They watch the slurry level during pulsing. When the level quits dropping, further soil compaction in the drill hole sidewalls and base is not possible. After the pulse process is complete, workers insert a rebar cage and the pile is finished.The process does not alter the soil mineralogy. The electrical discharge is internally grounded and does not arc to the sidewalls of the drill hole. Soil is not scorched or altered in any manner; it is only compacted by the pressure wave. This technique has been used in urban areas with no effect on electrical or electronic equipment."

Jan 1, 2009

By Kazimierz Gwizdala

In recent years, in Poland the ATLAS piles have been successfully applied for some constructions near Gdansk. The piles have been used as foundations for housing and another areas of civil engineering, in delta Vistula geotechnical region, characterized by weak, highly compressible soils represented by mud and peat, lying in sub-surface layers, several meters thick. Usually below are dense sandy soils or gravel. In all cases, the base of ATLAS piles rested on sandy soils. The analysis of pile bearing capacity has been discussed and verified by static pile load tests (SPLT). The load-settlements characteristics obtained were satisfactory. In the paper, the results of geotechnical investigations as well as calculations and load tests are shown. The ecological aspects of ATLAS piles application within highly urban areas of the cities and complex geotechnical conditions are emphasized.

Jan 1, 2006

By Cheng Lin, Guoming Lin

"This paper presents a case history for the design, construction and long-term performance monitoring of a driven prestressed concrete (PSC) piled foundation supporting a large liquefied natural gas (LNG) tank in Savannah, Georgia, USA. Following a geotechnical investigation, a design stage pile test program was performed with three objectives: to study the densification effect from pile driving on the liquefaction resistance, to test axial and lateral pile capacities, and pile behavior under lateral loads. The test program comprised five piles driven on a test pad constructed adjacent to the tank foundation. Cone penetration testing (CPT) was performed before and after pile installation to test soil densification effects from the pile driving and liquefaction potential was re-evaluated based on the soil densities after pile installation. The axial load tests involved static load testing, high strain dynamic testing, and Statnamic testing. This paper presents the findings of the densification effects, compares results from different axial testing methods and discusses the procedures to use the load test results in the pile design. The paper also comments on the construction issues and presents performance data with 10 years of monitoring.1. IntroductionThe project site is located at the Kinder Morgan’s Elba Island LNG Terminal on the Savannah River which is three miles downstream of the downtown Savannah, Georgia. This LNG terminal was initially developed in the 1970s as an LNG import terminal. The facility includes five LNG storage tanks with two larger tanks which were constructed in 2003 and 2006, respectively. The terminal is currently being converted into a liquefaction and export facility. This paper discusses pile foundations for Tank D4 which is a double walled insulated steel tank built to hold one million barrels of LNG in 2003. This tank has an outer tank diameter of 258 feet, an inner diameter of 252 feet, and liquid height of 113 feet. A number of geotechnical challenges were present in the foundation design and construction.??The site is a typical coastal deposit site featuring a thick layer of very soft under-consolidated clay (up to 40 feet in thickness);??The bedrock is a couple of thousand feet deep;??There is a sand layer that is liquefiable under a high seismic design category (0.5% possibility of exceedance in 50 years)."

Jan 1, 1900

By Hui Yongning

This paper presents a simulating test of constitutive relation of soil anchor in laboratory and puts forward a new plastoelastic mechanical model, on which a new calculating formula of elastic and plastic limit bearing capacity for soil anchor is suggested and two engineering projects verify that this method is adaptable.

Jan 1, 1991

By C. J. Kirkland

For two thousand years and more, we insular Britons have been grateful for the existence of the narrow strip of water that separates us from mainland Europe. It has given us a sense of security against invaders, though it has been breached many times. The first recorded serious consideration of a fixed crossing of the English Channel was in around 1802, when it was suggested to Napoleon I. The motive was not entirely peaceable and the British Navy, who saw themselves as defenders of our shores, were decidedly unenthusiastic A whole series of imaginative schemes were proposed in the course of the nineteenth century, embracing viaducts, immersed tubes, artificial islands as resting places for the horses which were to draw carriages, as well as mechanically bored tunnels. The first Channel Tunnel Company was formed in 1872, and an application for permission to construct a tunnel was made to the British parliament. A Colonel Beaumont, of the Corps of Royal Engineers designed and constructed a machine which, in around 1882, bored over a mile of tunnel out to sea from Britain which exists to this day.

Jan 1, 1991

By Tracy Brettmann, Shailendra Endley, Jason Leary, Shashank Valluru

"Augered Cast-in-Place (ACIP) piles have long been used for deep foundation support in sands due to their high capacity and speed of installation. Very little information exists on the effects on capacity if the auger needs to be withdrawn from the hole prior to grouting. This condition can occur due to various reasons including grout plug ups, equipment issues, and grout supply delivery problems. It can become a major problem for the project team if this happens during production because the capacity of that pile is then in question, potentially resulting in re-design, installation of replacement piles and/or schedule delays. This paper compares the results of two high capacity test piles installed into a dense sand where one test pile was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth and the other test pile was installed utilizing conventional industry standard methods. Identical load tests were then performed on both piles to compare the effects of the two different installation procedures. The load test results were surprisingly similar in this case although the grout take required for the test pile installed in the pre-drilled hole was significantly higher to produce a similar grout return depth.IntroductionAugered Cast-in-Place (ACIP) piles are used extensively along the Texas Gulf Coast due to their combination of high capacity and speed of installation resulting in one of the most cost effective deep foundation systems relative to other options. Soil conditions in this region typically consist of alternating layers of sand and clay in the upper several hundred feet. ACIP piles are routinely installed to depths of over 100-ft to achieve the required capacity depending on the site specific soil conditions and therefore typically extend through and tip into sand layers. Occasionally, due to various reasons like equipment issues and plug-ups, the auger is withdrawn from the hole without grouting. Significant sand in the soil profile could lead to questions about the effect of the auger withdrawal on the pile capacity and load deflection relationship.This paper summarizes the results of two identical pile load tests performed on adjacent piles of the same length with the main difference being one was installed using the standard installation procedure and the other was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth. The load test results were then evaluated using load transfer analyses to estimate the effect of the withdrawal of the auger on the load-deflection characteristics and capacity."

Jan 1, 2017

By Jun Ohbayashi, Yoshiyuki Yagiura, Hiroaki Miyatake, Masuo Kondoh, Naotoshi Shinkawa

"Reducing the improvement ratio of ground improvement is an extremely efficient way to reduce the construction cost and construction period of mitigation measures for soft ground. The Arch Action Low Improvement Ratio Cement Column (ALiCC Method) is one method for this, and it is being increasingly applied to sites. This method enables us to rationally evaluate the embankment loads that are acting on cement improved soil columns and unimproved ground, by considering the arch action generated in the embankments and from there thusly allocate improved soil columns in spans of a greater distance than those needed for conventional methods. As a result, it serves to reduce construction costs and the construction period, while also minimizing the settling of the embankment and differential settlement, by placing numerous improved soil columns in the ground immediately beneath the embankment at equidistant intervals. In this report, we give a basic overview of the ALiCC Method, report typical construction results from real life cases that have been carried out, and make comparisons with other construction methods in order to report on the effectiveness of this design method.OVERVIEW OF ARCH ACTION LOW IMPROVEMENT RATIO CEMENT COLUMN (ALiCC) METHODIn the area of mitigation measures for soft ground, a significant role is played by ground improvements using improved materials such as cement. For this reason, a reduction in construction costs and construction period required for ground improvements has become of greater importance. The Public Works Research Institute carried out joint research with Kiso-Jiban Consultants Co. Ltd., Kitac Co. Ltd., and Fudo Tetra Co. Ltd. over a period from 1998 through 2002, and, from that, developed the ""Arch Action Low Improvement Ratio Cement Column Method"" (hereinafter referred to as the ""ALiCC Method"") that enables ground improvement with a lower improvement ratio (the improved area ratio is approx. 10% to 30%) than is required for conventional methods, while also ensuring stabilization and minimizing the settling of embankments.In the area of mitigation methods for soft ground by deep mixing, the dominant method until now has been that (50% or more of improvement ratio) shown in Fig. 1. This method comprehensively improves the area under the face of the slopes of both sides of the embankment. This is based on the calculated stability against rotational slip, which states, ""the most effective way to ensure the stabilization of the embankment environment is to carry out improvements of the area under the face of the slope."" Therefore, for the area under the face of the slope, ground improvement by deep mixing was done, and for the soft ground in the area under the middle part of the embankment, accelerated consolidation methods (hereinafter referred to as ""conventional method"") such as sand draining method and paper draining method were used. Mitigation measures that combine these improvement methods have also been mainstream for a long period of time and are used to prevent side deformation around the embankment. However, there have been some problems that have occurred, such as a situation where consolidation settling occurs in the center area under the embankment where no improvement had been carried out. This phenomenon leads to a situation in which the improved soil columns in the area under the face the of slope are pushed to the outside, which results in side deformation occurring around the area of the embankment, and additionally the occurrence of a step due to a situation of differential settlement between the improved ground and the consolidation advancing part, which results in cracks in the embankment."

Jan 1, 2015

By Richard Short

Shallow rainfall-induced landslides in residual and colluvial hillslopes and steep embankments are a common occurrence in many settings [1, 2, 3]. While occasionally posing a threat to property and life-safety, they more often present an ongoing maintenance problem and can lead to the initiation of larger failures. Typically, these slides consist of 2 to 4-foot thick translational movements of silty and clayey soils down slope through the reduction of strength from increases in pore water pressures. Direct surficial infiltration and indirect groundwater seepage are the normative triggers for failure. In the residential community of Blackhawk, California, located east of the San Francisco Bay, these types of landslides are a common occurrence (Figure 1). However, shallow landslides have also been a repetitive and constant problem along many state highways where steep embankments have been constructed in close proximity to busy thoroughfares. Given the real threat to property values in residential and commercial settings and the constant maintenance problem posed to lifeline structures such as utilities, roadways, and pipelines, new methods to deal with these landslides are needed.

Jan 1, 2007

By Silas C. Nichols

"Abstract Piling and deep foundations are a staple for transportation projects in the United States (US). Driven or bored piles have been used for everything from support of bridge foundations and retaining structures to support of culverts and embankments on soft ground. Deep foundations have been popular in the US transportation market to better handle large axial and lateral loads, extreme event loading, and to better control structure movement. However, there are challenges in the maintenance of design and construction codes in transportation for consistent and reliable structure foundation elements. A significant amount of effort continues in the US to maintain national codes and specifications at a level consistent with the state of practice, and identify and conduct research for providing safe and cost effective highway structures.IntroductionThe transportation sector in the United States has a hierarchy of design and construction codes that are used for the specification of piling and deep foundations. Any highway or bridge project on the National Highway System (NHS) must be designed and constructed in accordance with a national set of standards approved by the State Highway Departments, and that are acceptable to the Federal Highway Administration (FHWA). However, in any jurisdiction, exceptions are permitted with approval. Therefore, design may be governed by the national standard specification, a state standard specification and design manuals, special provisions, or guideline specifications. Any of these standards, or a combination, may be used depending on the needs of the owner agency.The FHWA and the American Association of Highway and Transportation Officials (AASHTO) have worked together in the development and maintenance of geotechnical design and construction guidance and codes that support the surface transportation community. General geotechnical engineering practice in the United States lacks a singular, national design and construction code that addresses all aspects of geotechnical engineering. As a result, the AASHTO specifications provide the most complete geotechnical specifications focusing on structure foundations, retaining walls, and buried structures for surface transportation applications. This includes piling and deep foundation types commonly used for support of bridges and transportation structures.The FHWA National Geotechnical Team has published several technical guidance documents that include guideline specifications for the design and construction of driven and bored deep foundations. Reference documents published by FHWA summarize the state of practice and provide recommended design and construction guidance. These reference documents have long served as a basis for provisions included in the AASHTO specifications. Maintenance of the design code and specification, and related guidance documents for consistent use on US transportation projects requires a collaborative effort between industry, FHWA, and the member state highway departments that make up AASHTO."

Jan 1, 2014

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"Previous studies revealed that the helix deflection reduced the end bearing capacity of screw pile in dense ground even if the installation process is completed with minimal soil disturbance. The ultimate end bearing capacity in dense ground is difficult to achieve during the full-scale pile load test due to the limitation of the loading system. Therefore, in the present study, model scale of testing is selected to investigate the effect of helix deflection on load settlement behavior of single helix screw pile under increasing stress level. It is observed from the test results that the applied surcharge pressure, which is used to simulate the effect of stress level, is decreased with increase in model ground thickness. This decrease in the stress level is due to the frictional resistance between the container wall and sand. It is also observed that the end bearing capacity of screw pile increases with the increase in stress level but at gradually decreasing rate. The test results indicated that the helix deflection during the pile load test should not be more than critical deflection (0.72 mm average) of the helix to avoid any reduction in the end bearing capacity of screw pile. The helix deflection, which is measured after the pile load tests are also compared with the equations of flat circular plate having uniformly distributed load over the plate with simply supported and fixed inner edges.INTRODUCTIONThe screw pile consists of a central steel shaft with one or more helices attached at different location on the central shaft. The installation mechanism of screw pile consists of torque and pushing force. The screw pile installation mechanism can affect the unit weight of the ground during its installation. This effect is small in cohesive soils but it is quite noticeable in loose to medium dense sands (Adams 2011; Santos et al. 2013). The pushing force should be controlled in such a manner that pile penetration should be at least 80% of the pitch of the helix, during each revolution (Perko, 2009)."

Jan 1, 2017

By Lu Yitan, Frances Badelow, Manish Tiwari

"Large ‘design and construct’ projects often present significant geotechnical risks. However, these also present significant opportunities for value engineering in design. These opportunities can be realised through systematic site investigation and close collaboration with the Contractor to dovetail the design solutions to suit construction methods. This paper presents a case study of a large infrastructure project in Singapore which involved design optimization of an earth retention system for a deep excavation in a constrained urban environment. The project also required installation of over one thousand bored piles in highly variable ground conditions - identified as a key risk. Systematic site investigation was undertaken to develop a reliable ground model. A detailed value engineering exercise identified opportunities for design optimization by changing the retention systems and construction sequence in some segments. An innovative low cost ground improvement method was used in some areas to reduce the forces on the retention system. An extensive instrumentation and monitoring plan was implemented for verification of design and to mitigate the remaining risks. This paper includes the lessons learnt on this challenging project, which are relevant to a wide range of construction projects.INTRODUCTIONSingapore has been rapidly expanding its underground Mass Rapid Transit (MRT) network over the past two decades. The Thomson-East Coast Line (TEL) forms part of this expansion and is 43 km long and fully underground comprising 31 stations. This paper describes the value engineering and design optimizations undertaken during detailed design of the earth retaining and support structures (ERSS) for one of the underground stations along TEL. The station, currently under construction, is up to 24m deep and 350m long. The edge of the station excavation is less than 10m away from the existing MRTviaduct. The proposed station is surrounded by high-rise residential and commercial structures, somewithin 2m of the excavation. Land Transport Authority (LTA) of Singapore imposes stringent technical and contractual requirements on MRT construction works to ensure high quality and safety standards. These include minimum requirements for embedment of retaining walls, groundwater control, additional site investigation, instrumentation and monitoring, and compliance to LTA’s Civil Design Criteria (CDC). Any deviations from the minimum requirements can only be approved by LTA after detailed calculations, analysis and field testing are completed and additional monitoring and control measures are proposed."

Jan 1, 1900

By Mario Mauro

The article illustrates the Hydromill technology, as applied in urban sites, and its advantages in terms of quality of the end product, mitigation of the construction impact, and optimization of the logistics at the site. Also highlighted are the main features of the excavation equipment and slurry treatment plant. Two recent urban applications of this technology in Europe are briefly described, together with the forthcoming application to the Central Artery/Tunnel Project in Boston. Introduction The Hydromill technology has been used extensively in Europe in the last decade for slurry wall construction in urban environments. In Italy, this technology has been applied by Ing. Giovanni Rodio & C., Impresa Costruzioni Speciali S.p.A. in two large projects. The first project is the construction of Stations Darsena and San Giorgio of the first metro line in Genova. The second project is the "Cut-and Cover" tunnel for the railway link in Torino. Hydromill technology will be used for the construction of the Soldier Pile Tremie Concrete walls of the Boston Central Artery Tunnel Project, contract C14C2, Utility Relocation at Fulton Street.

Jan 1, 1994