Search Documents

By Karl A. Higgins

In 1976, Prof. G. G. Meyerhof published a famous article in the Journal of Geotechnical Engineering titled ?Bearing Capacity and Settlement of Pile Foundations?. This article presents the authors opinions on calculating pile capacities in clays and sands, group capacities and pile settlement. A portion of the article presents correlations of shaft friction and end bearing to the Standard Penetration Test (SPT) N-value. Subsurface exploration via the Standard Penetration Test is the most widely used exploration tool in the United States, so correlations of pile capacity to N-value are significant to the practice of geotechnical engineering. Meyerhof?s SPT-N correlations are relatively simple calculations compared to other pile capacity computation methods presented in the article or found in other text books (such as the a-method, b-method, Nordlund, Vesic, Meyerhof?s semi-empirical, others) and therefore are popular amongst practicing geotechnical engineers. At the time these correlations were published by Prof. Meyerhof, utilization of dynamic testing with the Pile Driving Analyzer (PDA) was not widespread in geotechnical engineering practice. Prof. Meyerhof?s correlations appear to be based upon conventional static pile load testing of instrumented piles. Dynamic pile measurements to estimate a pile?s static capacity provides certain advantages over conventional static load testing, namely the determination of unit shaft friction values at discrete intervals along the pile, and the unit end bearing support value. The author has compiled a database of driven, displacement piles tested with dynamic methods (ref. ASTM D4945, Test Method for High-Strain Dynamic Testing of Piles). The data was collected between 2002-2010 and is comprised of displacement piles driven into coastal plain sediments in the mid-Atlantic states of Virginia, Maryland and the District of Columbia. In layered soils, dynamic testing in particularly helpful as it reveals the differences in unit shaft friction for varying soil types. One hundred ninety (190) piles are included in the database, with a corresponding 1,373 discrete shaft friction and 190 end (toe) bearing measurements. The pile type typically consisted of 12 and 14 inch square, prestressed, precast concrete piles; however, a significant number of piles were steel HP 12 or 14 inch sections. The database was sorted based upon soil type, and then correlations of shaft friction and end bearing were derived in the same or similar manner as Meyerhof?s original 1976 publication. The new correlations are compared to Meyerhof?s original values.

Jan 1, 2011

By Kishore Kumar B., Eswaran Prasad C R, Srini Naik B., Ramakrishna Raju N

The authors through this paper intend to introduce the non-vibro technique of ground improvement by stone column, being used for the first time in India under the Western Dedicated freight Corridor in Mumbai area. New 2x25 KV double line dedicated freight corridor tracks, capable of carrying 32.5-ton axle load are proposed to be built on this stretch. Non-Vibro Displacement Stone Columns of 900 mm diameter were installed to improve the safe bearing capacity of the soft ground to take the loading of Dedicated Freight Corridor Railway embankment. Vertical footing load tests on single and three column groups were conducted to assess the improvement in the sub-surface condition after installation of stone columns. This paper describes load tests conducted on stone columns and analysis of the obtained results. The observed load settlement behaviour of the improved ground has also been presented. Behaviour of single and group of stone columns have been compared and criteria adopted for arriving at desired factor of safety based on the settlement observed, has also been discussed.

Nov 1, 2022

By Mihir B. Roy

"Coal transported by rail for Thermal Power Plant in Haldia, West Bengal, India, was to be received and stored in Coal Complex comprising of Wagon Tippler, Track Hopper, Junction Houses and network of horizontal and inclined tunnels. The site was very soft with high ground water level. Deep excavation and dewatering posed great difficulty. Original plan was to drive about 1000 m of steel sheet pile and well sinking which had major impact on cost and time. High ground water was identified as the main problem. Controlling water level and maintaining it would allow open excavation over major areas. Scheme for lowering aquifer with one and two-stage well-point dewatering system was developed following basic principles of groundwater and seepage. Arrangements of wells, installation and pumping were worked out in detail. Water levels could be lowered below bottom levels of excavation. Design of sheet pile was modified under lowered ground water condition. Overall length and depth of sheet pile were reduced drastically. Open excavation was possible in segments over major areas. The scheme was highly successful in smooth and fast progress of underground works. The works were completed safely months ahead of schedule time and with significant saving in cost.INTRODUCTIONThe Coal Receiving Complex of thermal power plant comprised of 250 m long 8 m deep Track Hopper (TH), 12 m deep Wagon Tippler (WT) with provision for addition of another Wagon Tippler. Track center lines of TH and WT were very close. Coal unloading facilities were connected with a network of underground tunnels and Transfer Points (TP) upto Pent House (PH). The facilities were optimized in a compact layout within about 400 m x 120 m area. Initially excavation for TH was started adopting side slope of (1 V : 1.5 H) with 2 m wide berm and dewatering by in-pit sump and pump. When depth of excavation reached about 5-6 m, failure occurred over a long stretch as shown in Figs. 1a - 1b photos. Further work was stopped to develop scheme for carrying out deep excavation and civil works safely."

Jan 1, 2015

By H. Cheng

The Bohai Oil Company has applied all together 11 jack-up oil drilling rigs (movable platforms) (1) which can be classified in terms of their forms of foundations into two types: the integ­ral mat and the column legged, as demonstrated in figure 1. Figure 1 a) indicates the entire structure of the sunk cushion type, i.e. the one with a box-like sunk cushion serving as its foundation by directly sitting on the sea bed. The length, width and height of the outer sides for the sunk cushion stand at 45.8 x 38.0 x 3.3m ( for Rig Bohai No.2 ) and 50.6 x 33.2 x 4.88m ( for Rig Bohai No.6 ), the relative areas of theirs being 1475m2 and 2008m2 respectively and both bigger than the plane areas of the rigs. With a view to realize a convenient drainage of mud while sinking, two holes of 14 x 14m and 32 x 18m in size are constructed in the center part of the sunk cushion. When work sets off, the underside of the sunk cushion operates as a foundation, the sunk cushion being connected to the platform by hull columns which transmit the load of the platform down­wards to the sunk cushion that passes it further onto the subgrade. [ ] Column legs for rigs may also be grouped into two categories considering their features: columns with and without boots. The bodies of boot columns are made up of trusses, whose bottoms, are boot-shaped with a big diameter. The diameter of boot columns of the rigs applied by the Bohai Oil Company shows bigger and it may reach 12 or 18m. In the boot columns, the transmission of the platform's weight into soil is done by the underside areas of boots. While in the case of the vertical columns, which are of cylinder columns of steel with sealed bottom ends shaped inverted arch, the entire drilling platform is supported by the carrying force delivered by the bottoms of these steel cylinders and the frictional force rendered by their outside walls. Such a type of columns is featured by a small diameter, 3m in general. Figure 2 exhibits the schematic diagram of sections regarding the two types of column legs.

Jan 1, 2010

By Dan Mahrt

"In June of 2009, a slope failure occurred along River Road in Bismarck, North Dakota. The slope failure affected approximately 300 feet of River Road with vertical displacements up to 3 feet, resulting in closure of the road. River Road travels along the Missouri River in Bismarck in a geologic area riddled with historic slope failures of varying sizes. River Road is a city roadway which travels along the Missouri River. The toe of the failure extended into the Missouri River, therefore methods to repair the slope needed to be constructed within United States Army Corps of Engineers (USACE) requirements, and be acceptable to the City of Bismarck. As this is a scenic area along the river, the stakeholders desired to maintain the scenic landscape along the roadway as a part of the slope stabilization.Due to the magnitude movement of the failure mass, the geometry of the failure was relatively easy to evaluate. In evaluating remediation options and collaborating with the USACE, the team determined that the scarp was situated primarily within the navigable portion of the Missouri River. This required USACE approval for any repair or remedial work downslope of the roadway. The City of Bismarck wished to reopen the roadway as soon as possible, therefore stabilization options were limited to working within the road right-of-way to avoid permitting for working within the navigable waterway.The remediation solution for this project involved a combination of driven H-pile and placement of lightweight fill to re-construct the roadway at the original grades, and avoid impacting the navigable portions of the Missouri River. This paper discusses the unique project constraints and the innovative solution using multiple technologies to successfully stabilize the slope.BackgroundIn June 2009, Bismarck, North Dakota experienced two consecutive days of significant rain resulting in over 5 inches of precipitation in a 36-hour period. Shortly after these rain events, a slope failure was noted on River Road, a city street along the Missouri River in Bismarck. Initial findings noted the slope failure affected about a 300-foot long portion of the roadway, with vertical displacements of about 2 feet. The city of Bismarck closed the roadway and began evaluating repair solutions for the road."

Jan 1, 2016

By Stephen Buttling

The construction of a water treatment plant in Dandenong, Victoria, required detention tanks and a pumping well. The design provided by the Engineer used conventional rectangular cast-in-situ reinforced concrete walls within a sheet piled cofferdam. It was decided to construct the tank and shaft using the diaphragm walling technique as an alternative and, for the shaft in particular, this involved a “circular wall”. Except where cutters are used, joints in diaphragm walls have to be made between colinear panels, with waterproofing provided by dumb-bell water stops held within trapezoidal forms. This means that the circle has to be approximated by a number of straight sides, which in this case was twelve. The requirement was to design the reinforcement for the strange shaped panels. Finite element analysis was used, in the first stage using an axisymmetric model to determine the profile of lateral earth pressures with depth. In the second stage a horizontal slice was modelled, without gravity which normally operates from the top to the bottom of the page. By considering appropriate possible earth pressures at different depths, a range of bending moments was calculated, which was used by the structural engineers to design the rebar. The tanks were successfully constructed, and inclinometers were installed in both the tank and the shaft. Measured deflection profiles show that the design was moderately conservative.

Nov 1, 2022

By S. P. Mukherjee, Smita Tung

"Piles are generally subjected to uplift in case of under ground and water front structures. Sometimes piles are also to resist uplift loads in transmission towers, dry rock, and so on. Experimental investigations of single piles and pile groups have been carried out using model hollow circular aluminum piles, having 25.4 mm outer diameter and lengths of 600 mm, 750 mm and 900 mm. Pile groups of 2?1 and 2?2 arrangements have been used in the experimental investigations. L/d ratio has been kept equal to 24, 30 and 36 in all the cases. All the single piles and pile groups have been tested under vertical uplift. Spacing between two piles in a group has been varied with respect to pile diameter such that spacing to diameter ratios of pile are 3, 4 and 5 in case of pile groups. An attempt has also been made to analyze those models of single piles and pile groups under vertical uplift by PLAXIS 3D software. Good analogy has been observed between the results of experimental and numerical studies. A parametric study has been carried out to observe the variation of ultimate uplift capacity of pile groups with spacing and depth of embedment. It is observed that for a particular embedment length of pile and a particular group arrangement the ultimate uplift capacity increases with increase of spacing. It is also investigated that for a particular spacing and particular group arrangement, the ultimate uplift capacity increases with increase of embedment depth. Those variations have also been presented with graphs which are generated considering non dimensional forms of parameters. The paper brings out change in pullout capacity of pile groups with spacing and embedment depth of piles.1. INTRODUCTIONPrediction of uplift capacity of single piles and especially of pile groups is one of the most interesting areas of research in geotechnical engineering. Pile foundations are frequently used to transmit the superstructure loads to deeper strata if the subsurface soil is of inadequate strength. The worst possible case may be considered to occur when all the piles in a group subjected to uplift. In cohesionless soils, the shaft resistance is an important source of pile capacity under axial loading, especially when the pile is subjected to uplift loading. Poulos and Davis (1980) recommended estimating the uplift capacity of piles as 2/3 of the downward shaft resistance. Later Ramasamy et al. (2004) indicated that the upward shaft resistance is significantly less than the downward shaft resistance. Some studies were conducted on the behavior of a single pile under uplift loads, such as those by Sowa (1970), Vesic (1970), Das and Seeley (1976), Levacher and Sieffert (1984), Rao and Venkatesh (1985), Chattopadhyay and Pise (1986), and Shanker et al. (2007). Das et al. (1976) conducted a model study to test the uplift capacity of single piles and pile groups buried in sand, and they also determined a relationship between the efficiency of a pile group and its spacing. Chattopadhyay and Pise (1986) proposed an analytical method for predicting the uplift capacity of piles embedded in sand and obtained reasonable agreement between experimental and theoretical results. Gaaver (2013) investigated experimentally that an upward displacement of about 1.4–2.5% of the pile diameter is required to attain the net uplift capacity for both single piles and pile groups. The uplift resistance of pile groups depends on the several variables like group size, shape, spacing to diameter ratio of piles, embedment depth to diameter ratio of piles, soil type and its density and soil-pile friction angle."

Jan 1, 2015

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

By Jim Bruce

The Transformation AGO project, constructed between 2005 and 2008, featured a foundation trade contract that included design of pile caps and grade beams and construction of 138 permanent micropiles. The new foundation works were constructed within seven different settings ? each featuring a host of attributes challenging to constructability ? inside and outside the existing Art Gallery of Ontario, all while the gallery remained open for business. Transformation AGO resulted in several firsts for micropiles in the Toronto construction market: this was the first micropile trade contract with a multimillion dollar contract value; it featured the first static compressive load test performed beyond 7000 kN on a single micropile; the first static compressive load test beyond 8000 kN on an experimental pile cap supported by two test micropiles; and it was the first publicly funded project to go to tender with micropiles listed as the preferred foundation option. This paper outlines the successful application of micropiles at the landmark Transformation AGO project.

Jan 1, 2011

By Sung-Ryul Kim, Woong-Jong Park, Juhyung Lee, Si-Hoon Lee

"A bucket foundation has been considered to be a potential foundation technology for offshore wind turbines. In this study, a series of 1-g model tests were performed to analyze the accumulated rotation of suction bucket foundations under long-term cyclic horizontal loads. The model suction buckets were made to have the embedment ratios of 0.5 and 1. The dry model ground was prepared to have two different soil densities by air-pluviation method. A horizontal cyclic load over 104 cycles was applied varying the loading amplitude. Test results showed that the accumulated rotation of the bucket foundation increased with the increase in the number of cycles and load magnitudes. Based on the model test results, a new equation was proposed to evaluate the accumulated rotation of the bucket foundations in sandy ground under long-term cyclic horizontal loads.INTRODUCTIONRecently, a bucket foundation has been considered to be a potential foundation technology for offshore wind turbines. In terms of economy, a bucket foundation has been considered to be an economical foundation type at sea beds where ground condition is clay or medium dense sand.A bucket foundation resembling a bucket is a kind of suction-installed foundation units. It is a skirted steel foundation which is open at the lower end and closed at the upper end by a lid. The embedment depth ratio (L/D) of a bucket foundation is usually less than one. Figure 1 shows an example of a bucket foundation. Offshore wind turbines are subjected to long-term cyclic loading by wind or currents. A bucket foundation is installed in soil grounds, so the long-term cyclic loading may induce the accumulation of soil deformation.In this study, the accumulated rotations of the bucket foundations in sandy ground were investigated under long term cyclic horizontal load. The number of cycles up to 104 cycles was applied varying load magnitude. The accumulated rotations of the bucket foundations in sandy ground were analyzed based on the test results."

Jan 1, 2016

By Kjell Karlsrud

"Abstract New semi-empirical design procedures for the determination of ultimate shaft friction and load-displacement response of axially loaded piles in clay are proposed. Hereunder also prediction of how the capacity will build up with time following the pile installation, primarily as result of reconsolidation. A main basis for developing the new procedures was detailed review and re-assessment of results from a series pile load test programs published over the past 30 years on piles well instrumented to monitor soil- and pore pressures as well as load distribution along the pile shafts. Two new alternative procedures are proposed for predicting the ultimate shaft friction; a-approach using the normalised undrained strength based on direct simple shear tests as a main correlation parameter, and ß-approach using the overconsolidation ratio, OCR. Both approaches include the effects of the plasticity index of the clay, Ip, which is shown to have an especially large impact on the correlations when Ip<25. It is recommended to use both methods in design practice, and select design values for the ultimate shaft friction that represents an average for the two methods. Pile diameter, length or stiffness, or whether the pile is open- or closed-ended seem to have little impact on the shaft friction. However, a moderate effect of pile length or flexibility on the total ultimate pile capacity comes out of the proposed t-z curves, which include some post-peak reduction. The proposed procedure for predicting the time for set-up is based on linear radial consolidation theory. The main input parameters are the insitu permeability and virgin modulus number (or virgin compression index) of the undisturbed clay. The same basic formula and correlations are applicable to both open and closed-ended or partially plugging piles.IntroductionThe design procedures presented herein are primarily based on observations and data collected in connection with “fully instrumented” pile testing programs that the author has been responsible for or has become involved with over the past 40 years, or that have been found in the literature.It was a pre-requisite for the test programs included that there were sufficient high quality soil data available to give a reliable determination of the true in-situ strength and compressibility characteristics of the clay deposits. The soil conditions range from soft NC clays with undrained shear strength down to about 15 kPa, to very stiff clays with undrained shear strength up to about 500 kPa and OCR up to 25. The plasticity index of the clays mostly lies in range 12 to 60 %."

Jan 1, 2014

By Rafael A. Rivera

"Since the dawn of construction, there has been a need for excavations, which sometimes need to occur below the groundwater table. Excavations in themselves are difficult enough, with the myriad of requirements, such as engineered support of excavations, considerations for stability and numerous other concerns. Excavations executed in rural landscapes can be accomplished easily without significant consideration to accessibility, adjacent properties or structures, and construction limits and deformations. However, all of these factors can have an impact on excavation considerations in an urban landscape. When digging below the groundwater table, these conditions, along with concerns associated with groundwater drawdown requirements, discharge limitations, groundwater contamination, property limits, adjacent buildings and subsidence concerns, can lead an experienced dewatering contractor to consider diverse installation methodology and equipment to allow construction to occur below the groundwater table.534 W. 29th St. New York, N.Y.There are many things that must be considered when constructing a new high-rise building within a small property footprint measuring 25 ft (7.6 m) wide by 80 ft (24.4 m) in length. When you take into account that the foundation needs to go several feet below the groundwater table and that there are two existing multistory buildings with shallower foundations on either side of the proposed structure, this task now becomes much more difficult. Consideration of geology, groundwater levels, depths of excavation and shoring for the excavation becomes critical to the success of the project. On a regular basis, dewatering contractors confront similar situations in congested cities where available real estate is limited.To minimize the negative impacts of construction dewatering, it is important to mitigate the potential effects of construction dewatering to the surrounding buildings, sidewalks, underground structures, tunnels, subways and other existing infrastructure. Such an instance occurred at the project located at 534 W. 29 St. in New York City. On this particular project, the required drawdown was greater than the typical 15 ft (4.6 m) of suction lift, so a vacuumed can pump system was utilized. The tubing was connected to a vacuumed perimeter dewatering well-point system, which is a predrainage system that is installed prior to the start of excavation for the underpinning of the adjacent structures and for the overall foundation. Each well-point, which was composed of a PVC pipe that was 1.5 in (38 mm) in diameter by 25 ft (7.6 m) long, was drilled to a depth of about 23 ft (7 m) using a hollow stem auger and was installed around the perimeter at a centerto- center spacing of about 7.67 ft (2.3 m). In lieu of a traditional perimeter collection header, and to allow for greater flexibility for the contractor, the well-points were interconnected to a modified vacuum can pump system utilizing ¾ in (19 mm) drop tubes that were “spaghetti” around the perimeter."

Jan 1, 2017

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017

By Shreya Vivek Hokam, Dr. A. I. Dhatrak, S. W. Thakare, Dr. Vivek S. Hokam

Construction in congested urban areas has necessitated tall and massive structures. In urban areas, it is common to construct underground structure nearby existing buildings. Selection of an appropriate support structure system to be implemented in the excavation in an urban area is heavily dependent upon the geotechnical conditions and safety of the surroundings and neighbouring structures. Urban Rail, popularly referred to as Metro Rail, has seen substantial growth in India in the recent years. More cities are experiencing the need for metro rail to meet their day-today mobility requirements. The metro structures involved deep excavation for foundations which induces the stresses and thereby alters the existing equilibrium and thus may affect stability of neighbouring structures considering safety point of view. Hence, design and execution of deep excavations become one of the important challenging tasks of any geotechnical engineer in the modern era. Further, it is important to control the ground movement in order to prevent the failure of excavations. This involves specialized foundation technologies, usage of sophisticated equipment and new methods in underground construction, safety and monitoring systems. In this paper the methodology used for protecting adjoining structures due to deep excavation for Nagpur Metro station is studied.

Sep 1, 2022

By Osama Safaqah

The new Cooper River Bridge will replace two existing bridges along U.S. Highway 17. The cable-stayed bridge will be one of the largest in the U.S and will connect the City of Charleston and the town of Mount Pleasant, South Carolina. The 1,546-foot long main span over Cooper River is supported by two diamond-shaped towers and will allow for 1000-foot wide navigation channel. The Charleston high-level approach is approximately 4351-foot long and will provide 250-foot wide navigation channel over Town Creek, while the Mount Pleasant high-level approach is 2090-foot long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. Among various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against lateral loading. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies coastal sediments of interbedded clays and sands. The main towers will be supported on a group of 11 shafts and protected from ship collision by a rock island. The High Level Approach piers will be supported on a pair of 2 shafts. The shaft tip elevation is up to 230 feet below water line. An elaborate geotechnical investigation has been conducted on the site including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2005

By Gandhi

Piled raft foundation under uniformly distributed vertical loads has been analyzed using Finite Element Method. The soil is considered to be linear elastic, isotropic, homogeneous. The raft,pile and the soil have been idealized with eight noded brick elements. Parametric study have been carried out varying pile length, soil modulus, raft thickness, and pile spacing. Design charts have been produced to achieve 50% load sharing between pile and raft for optimum design. Data available in literature is compared with the design chart results and found satisfactory.

Jan 1, 1996

By Y. M. Ha, T. D. Nguyen, D. T. Nguyen, H. K. Choi

Conventionally, cement deep mixing (CDM) columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern may be inefficient in cases of spread footings or shallow foundations. This paper first briefly introduces principles of an improved CDM method that can create head-enlarged CDM (termed PF) columns. A simple analysis approach was introduced to obtain optimal shape of PF columns that results in minimum settlement. The effectiveness of this improved method over the conventional CDM method was then illustrated by settlement analysis for an actual footing in a case study using two recommended analytical methods in the literature. Analysis results from the case indicated that by using the same amount of soil-cement mixed volumes, settlement from a footing on PF columns can reduce up to 10 % compared with that from the same footing on CDM columns. In addition, a material quantity comparison for the case indicated that to have the same settlement values the volume of each PF column can be reduced of around 10% compared with that of the CDM column. INTRODUCTION The cement deep mixing (CDM) method is one of the most popular methods in ground improvement works. Details on the method such as construction procedures, necessary equipment and recommendations are described in many references or manuals (e.g. Bruce et al. 2013, BS EN 2015, Kitazume and Terashi 2013). Conventionally, CDM columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern is found inefficient in cases of spread footings or shallow foundations as the upper soil layers are naturally weaker than the deeper ones but are subjected to larger amount of induced stress from the superstructures.

Jan 1, 2019

By Frank Callanan

The Ameristar Casino expansion project included the design and construction of a 25-story hotel and 9-story parking structure expansion. The site is located in a floodplain on the banks of the Missouri River in Saint Charles, Missouri, where the underlying soils are potentially liquefiable. The geotechnical engineer performed subsurface exploration and analysis, which included site-specific seismic response and liquefaction, and provided geotechnical design recommendations. In the event of an earthquake, post-liquefaction settlement was calculated to be approximately 14 inches. Additional project constraints included wetlands protection, construction adjacent to the existing facility, flood protection and river bank stability. Because of the liquefaction issue, the geotechnical engineer consulted with a specialty geotechnical contractor on ground improvement methods. This consultation led to a proposal to eliminate deep foundations from the design and support the structures on shallow and mat foundations. The geotechnical engineer assisted the design team with foundation design analysis and value engineering assessments. Together with the project team, the geotechnical engineer used the data to evaluate foundation options and construction methods to overcome the site challenges and concluded that ground improvement was the optimum course of action. Because of the nature of the site constraints, a number of ground improvement methods were needed. The geotechnical engineer evaluated the methods proposed by the geotechnical contractor and provided the technical specifications for the ground improvement bid package, which included vibro-compaction, compaction grouting and micropiles. The ground improvement allowed for the use of shallow foundations (mat and spread footings), which provided the client with significant time and cost savings over the deep foundation alternatives.

Jan 1, 2009

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.