Search Documents

By Harry Schnabel

A 6200 m² cement deep soil mixed (CDSM) wall was constructed for an addition to the Museum of Fine Arts in Boston, Massachusetts. The addition was located along the east side of the existing museum within an existing courtyard and in the area of a recently demolished structure. The basement for the new addition extended up to 9.1 m below the floor slabs of the adjacent buildings. The adjacent buildings are supported on a variety of foundations including; shallow spread footings on alluvial sand deposits, low capacity piles bearing in the alluvial sands and Boston blue clay, and caissons bearing on the alluvial sands and clay. Groundwater was less than one meter below the top of the CDSM wall. The new addition was founded on shallow foundations in the desiccated crust of the Boston Blue Clay. The CDSM wall was selected as the most economical means to control deep seated ground movements, limit movements of adjacent structures, and inhibit groundwater flow into the excavation. Braces and a continuous wale were used to support the CDSM wall where it was located adjacent to structures. Tiebacks were used where there were no structures. Other geotechnical construction at the site included: ? Jet grouting (JG) to improve the ground and provide an impervious subgrade layer at the west end of the addition, ? Concrete pier underpinning was used to support an existing structure on the west end of the site, and ? A secant pile wall using alternating drilled shafts and jet grout columns was used for earth support and a barrier to groundwater flow to allow for the installation of a storage tank at the south end of the site. Inclinometers, total station surveying, vibrating wire strain gauges on the braces and wales and load cells on the tiebacks were used to monitor performance of the excavation support system. The excavation support system performed better than required limiting lateral movements of the adjacent structures to less than 13 mm and vertical settlement to less than 8 mm. No settlements or movement were detected during the construction of the wall. Lateral movement of the CDSM wall was typically below 15 mm with the maximum movement occurring near subgrade.

Jan 1, 2011

By Mohammad Eslami

The Tabriz-Urmiyeh Highway shortens the distance of north-western cities of Iran by about 130 km, resulting in improved access and efficient transit between Iran and Europe through Turkey. The highway crosses the Urmiyeh Lake, an inland lake surrounded by mountains. Due to the circulation of salt-water in the lake and the necessity to continue shipping between adjacent ports, a waterway should be kept open. Consequently, a bridge was built to provide access of marine traffic. A causeway bridge had a length of 1,260 m, comprising of 19 spans. In construction of the bridge, more than 400 piles having a total length of 32 km have been driven. For design of piles different methods have been used such as static analysis, dynamic testing, and correlations to in situ tests, such as cone penetration test (CPT). This paper presents construction of bridge substructure, full-scale piling tests, and methods of analysis used in the evaluation of the deep foundation capacity. The presentation includes an assessment of four current direct CPT and one CPTu methods to calculate the bearing capacity of the piles. It was found that the CPTu and dynamic testing are two suitable tools for rapid and optimum pile design and verification.

Jan 1, 2010

By Alan B. Wagner

Data from seven instrumented pile load tests in Milwaukee, Wisconsin and two other instrumented load tests reported in the literature, one in Evanston, Illinois and one in Houston, Texas were reviewed. The data were for pipe piles having diameters from 9-5/8 inches to 18 inches, driven to depths between 36 and 96 feet. These data were used to develop a relationship between effective vertical stress and unit side friction and unit end bearing. These relationships were based on readily measured soil parameters, undrained shear strength, Cu, and Standard Penetration Test (SPT) values. This Beta (ß) and Nt approach and four other methods were then used to calculate the bearing capacity of the nine cases analyzed. The results from each of the methods are compared with the measured results.

Jan 1, 1991

By Roger A. Archabal, Omar A. Conte, Gustavo Langoni

This international case study focuses on the rigorous geotechnical interaction and results of a soil improvement program utilized to mitigate consolidation settlements of over 1.5 m [5.0 ft]. The extreme settlement results from very deep, nearly normally consolidated clay and the required high floor loading of a new Logistics Park near Bogota, Colombia. The general subsurface conditions consist of very soft clay extending to depths beyond the 50 m [164.0 ft] explored. A required 1.2 m [3.9 ft] thick fill combined with high floor loads resulted in an applied areal load of approximately 7 ton/m2 [1300 psf] (equivalent to about 4.5m [15.0 ft] of fill). Langan recommended performing a test section to validate the initial consolidation settlement calculations and evaluate possible optimization of the prefabricated vertical drain (PVD) spacing and length. The test section sizing was designed to accurately represent the stresses at depth of the future structures. Extreme settlements of over 1.5 m [5.0 ft] in the center and large differential settlements of over 0.6 m [2.0 ft] were measured between the center and corners of the test section over a relatively short test time. Discussion on the methodology, instrumentation, measured results and future optimization are presented. The recommended soil improvement varied from the standard approaches typically utilized in the area. PROJECT LOCATION AND DESCRIPTION The project site is immediately north-northwest of the city of Bogota in the Bogota Valley. The site is bordered with, and has historically been, farming land bordered to the south by the El Rosal-Bogotá highway. The overall site encompasses about 570,000 m2 [141.0 acres] of gross area and about 484,000 m2 [119.6 acres] of net buildable area. The warehouse complex will consist of 10 very large warehouses with footprints ranging from about 15,000 m2 [3.7 acres] to 30,000 m2 [7.4 acres]. The total building area is about 210,000 m2 [51.9 acres] with most of the remaining areas being paved principal drives, truck parking or administrative parking. The topography of the site is relatively flat and close to final grade in roadway areas. However, the warehouse floors will be raised about 1.2 m [3.9 ft] (equivalent to about 2 t/m2 [370 psf] considering engineered fill) to allow for truck docking. In addition, the design floor loads are heavy and estimated to be up to 5 t/m2 [930 psf] and equivalent to about 2.5m [8.2 ft] of fill. Geotechnical conditions at the site are very weak at depths of 50 meters [165 ft] or more, with soft compressible clays comprising the majority of the soil profile. The Bogota Valley is composed in some areas of very deep alluvial deposits. These deposits have been classified as an important challenge and limitation to the development of high/heavy structures such as the project in question for many years (Orozco, 2006). Soft clay deposits have been encountered even beyond depths of 100 meters [328 ft] in some regions of the Bogota Valley (Sanz, 1994). Extreme settlements can be expected if extensive and high permanent loads (above preconsolidation stress levels) are supported in these thick alluvial deposits.

Jan 1, 2018

By Robert R. Morrison

Alberta Piling Contractors very rarely are required to perform major marine construction in the prairies, so it became as a big surprise to AGRA Foundations Limited to be invited by Transalta Utilities Corporation to bid on a major marine project for the Sundance Cooling Pond Expansion at Lake Wabamun, Alberta. Even more of a shock, the work had to be undertaken during Alberta's harsh winter conditions with temperatures plunging to -30 C. Not a happy situation for prairie construction workers to be in, working from barges in the middle of a lake in the dead of winter. However, it is well known that prairie boys make the best sailors.

Jan 1, 1997

By Edward L. Hajduk

During sonic logging quality control testing of the drilled shaft foundations for the replacement bridges crossing the Broad and Chechessee Rivers for SC 170 in Beaufort County, South Carolina, irregular signals were observed on a consistent basis near the shaft top elevations. These irregular sonic signals were attributed to access tube ?debonding?, which is the separation of the access tubing from the surrounding concrete. A total of 160 drilled shafts were installed for this project, of which 41 were evaluated using sonic logging testing. Both PVC and steel access tubes were used during the project to allow for sonic logging testing. This paper details the investigation of access tube debonding with time, discusses the solutions used to minimize access tube ?debonding?, and presents the results of the sonic logging testing for the entire project. The solution selected, installation of PVC along the pile length and steel access tubing within 40 feet from the top of shaft, allowed for reliable sonic logging to effectively evaluate the upper portions of the drilled shafts.

Jan 1, 2004

By Mohammed Sakr

A Two-Section Helical Pile (TSHP) is a steel pipe with two shaft sections of different diameters and with one or more helix plates near the bottom of each shaft section. TSHPs are used regularly in western Canada as foundation pockets for single and double circuit distribution power line poles. The results of a comprehensive lateral pile load test program and the field monitoring of TSHPs installed in organic soil (muskeg) over soft clay are presented in this paper. A total of nine full scale lateral load tests were carried out, including seven tests using TSHPs with different diameters and embedment depths, and two tests using one-section helical piles. The prime objective of the study was to evaluate the lateral resistance of TSHPs installed into very soft organic soil (muskeg) overlying soft clay soils, to compare their lateral resistance relative to one-section helical piles and to compare the measured and the estimated lateral resistances using p-y curves. In order to provide sufficient soil data for analysis, the subsurface soil stratification was evaluated using two different techniques including; Cone Penetration Tests (CPT) and Portable Soil Probe Tests (PSPT). The two testing techniques were also compared and evaluated. This paper summarizes subsurface soil conditions, pile configuration, helical pile installation procedure, testing setup and results.

Jan 1, 2009

By Gary Kuhns

Central Florida is among the fastest growing urban areas in the United States, and its rapid development has required the steady construction of various types of civil engineering works. The karst geologic terrain and variable geotechnical conditions, however, present special challenges to the design and construction of deep foundations. The subsurface profile can be idealized as a surficial layer of Pleistocene sands, underlain by the highly variable Miocene-age Hawthorn Group, consisting of various combinations of sand, silt, clay, phosphate and highly weathered limestone. The Hawthorn Group is underlain by Eocene-age limestone that comprises the Floridan aquifer. Vast networks of solution cavities are present throughout the Eocene limestone, sometimes allowing downward raveling of the overlying soils and the creation of sinkholes. In some cases, the relic sinkholes can be filled with soft compressible organic soils extending to depths greater than 100 feet (30.5 m). Driven piles are frequently employed as a deep foundation alternative, although occasionally cast-in-place piles/shafts have also been used. Piles are often driven for bearing in the weathered limestone within the Hawthorn Group, but are sometimes installed as friction piles in the upper soil and intermediate geomaterials. Dynamic pile testing is routinely performed during pre-construction test pile programs, or during production for quality control and assurance purposes. This paper presents discussions on the design and construction aspects of deep foundations unique to Central Florida subsurface conditions and local practice. Foundation issues such as subsurface variability, soil setup, pile damage, negative skin friction, and sinkhole conditions are discussed with the aid of demonstrative case histories.

Jan 1, 2003

By Paul J. Axtell

The design-build delivery system is being used to erect the landmark Christopher Bond Bridge as part of the kcICON project. The cable-stayed bridge is currently under construction and will span the Missouri River on I-29/35 in Kansas City, Missouri. The design-build process for the foundation work on this project has been successfully implemented as a result of cooperative efforts between the foundation designers and the constructors to develop a constructible design.

Jan 1, 2009

By Guo H. Lei

Over the last four decades, barrettes have been ever-increasingly adopted as the foundations for tall buildings and heavy infrastructure projects all over the world. Many findings have been gained from practical applications and theoretical researches. In this article, a collection of literature is reviewed on the installation effects and load-carrying behaviour of barrettes derived from field and laboratory tests and theoretical studies. It covers many aspects, such as the ground deformations and stress changes caused by the installation of barrettes, the shaft resistance mobilisation behaviour, the construction effects on the shaft resistance, and the effects of pile spacing, pile shape and pile group layout on the load-carrying behaviour of barrettes.

Jan 1, 2006

By Randy R. Huberty

Although originally designed with deep foundations consisting of all driven steel H piles and drilled caissons, a unique application of Augered Cast-in-Place (ACIP) piles as an alternate design resulted in a significant cost savings for the Midfield Terminal Project at the Pittsburgh International Airport. The project was enormous in scope covering an area two miles long by one mile wide, with changes in elevation of over 200 ft. The varying geology combined with the large amounts of fill required resulted in a complex set of geotechnical design parameters that had to be evaluated through both load testing and analyses. A total of almost 400,000 lineal feet of ACIP piles were installed for this project.

Jan 1, 2001

By M. Mets

Pile foundations have been used in Estonia since the beginning of 1960's. To evaluate the capacity of piles nearly 2,500 pile tests and 1,800 pile loading tests Have been carried out. The pile foundations of nearly 150 houses are under settlement observations.

Jan 1, 2000

By Mait Mets

In Estonia, the deformations monitoring of 1500 buildings are currently under investigation, buildings on pile foundations make up 10 per cent of these. In the following text we will be considering the behaviour of pile foundation buildings in various parts of Estonia, in differing geotechnical conditions.

Jan 1, 2002

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The subsurface soil profile consists of up to 50 ft of a soft organic silty clay layer that is very vulnerable to scour, underlain by a deep deposit of hard sandy clay. Foundation construction in the Potomac River required the use of cofferdams to allow structural concrete work to be performed in the dry. This paper will the present the types of cofferdams used to construct the foundations for the WWB replacement project. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over a navigation channel in relatively deep water. Foundation construction included the installation of 48? to 72? open end steel pipe piles and cast-in-place concrete pile caps. To achieve the desired bridge appearance, pile caps were required to extend below the water surface and below the existing river bottom in shallow water locations. Conventional steel sheet pile cofferdams with tremie concrete seal were used to construct fixed span, shallow water piers. Selection of deep water bascule span foundation cofferdams was governed by several factors including contraction scour, environmental considerations and cost. Potomac River cofferdams, i.e., relatively shallow depth cofferdams that are supported by the foundation piling were selected. This cofferdam system provided a shallow profile which minimized contraction scour and the amount of filling in the river. Design issues include load selection and cofferdam stability in very soft alluvial soils. Construction issues include erection sequence, tremie concrete mix design and placement procedures.

Jan 1, 2013

By Madan B. Karkee

The understanding and the development of sound theoretical basis concerning the pile foundations has been phenomenal during the past few decades, considering the thousands of years the piles have evidently been in use. The importance of the quality assurance and the need for verification of load bearing capacity is being further reinforced rather than undermined by these developments. This is evidenced by significant developments made in the pile load test technology in recent decades, making it possible to make judicious selection of a test method, or a package of test methods, suitable for a given situation. The selection depends on the objective of carrying out the test and the reliability desired. Presently, the possible selection ranges from dynamic to static methods. The extent of dynamic effect in a test can be reckoned based on a dimensionless parameter defined as the 'relative duration'. Examples of different load tests are given for illustration of the different methods currently in use.

Jan 1, 1997

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

By Jacques Moraille

The public is asking for more aesthetic designs if they can be proven cost-effective at providing an appealing element to new dams. Lake Lenexa was designed and built around the idea of providing for basic dam functions such as flood control, enhanced water quality, recreation but also to provide an inviting community focal point for the residents to visit and enjoy; truly interact with the dam. The architecturally unique dam and ?one of a kind? spillway were designed to symbolize the water cycle as water moves from nature into the urban environment and the back to nature. A pedestrian bridge that spans the spillway offers visitors a good view of cascading pools and a fountain. The original Lake Lenexa dam layout incorporated relatively high, cast-in-place concrete retaining walls to form the spillway structure. The Black & Veatch project team performed a Value Engineering (VE) study to determine cost-effective means for implementing architectural features within the spillway, which resulted in innovative uses of construction materials not typically used in dam and reservoir construction. The VE study concluded that mechanically stabilized earth (MSE) retaining walls that are normally used for transportation projects would be a cost-effective alternative to the originally planned cast-in-place wall systems for the main spillway and stilling basins. The Black & Veatch study added value by mixing cement-kiln dust (CKD) with on-site clay soils to produce a stabilized material for use under the spillway. The CKD stabilized material properties include low compressibility, high strength and low permeability, which reduced seepage and uplift pressures under the spillway slabs. The cost savings provided by the VE alternatives reduced total costs and enabled architectural elements. The award winning dam design also used drilled caissons, expanded polystyrene (EPS) block forms, customized steel forms and external concrete vibrators to build the pedestrian bridge and upper spillway structures.

Jan 1, 2009

By David E. Albus, Ahmadreza Mortezaie, Bidjan Ghahreman

The structural evaluation of seismic performance of an existing hospital in Long Beach, California, required spring constants of foundation elements. The structure included support by deep foundation elements comprised of belled (underreamed) caissons. The available relationships in the governing building code (ASCE41-13) to compute axial stiffness is not applicable due to the belled configuration of the caissons. The large diameter of the bells required consideration of the foundation medium to the axial stiffness; a detail not clearly described in ASCE 41-13. Furthermore, prescriptive equations in ASCE 41- 13 used to estimate lateral stiffness only consider pile groups with the assumption that the only source of lateral stiffness is the axial reaction of individual piles. These assumptions were invalid for the project at hand where all caissons are configured as single foundation elements, not a pile group. In the present work, the approach taken to estimate seismic stiffness of single-belled caissons is described which accounts for the elastic behavior of the foundation medium below the bell base and lateral behavior of single-pile shafts. Results of the work provide a more satisfactory derivation of the spring constants consistent with current modeling methods. INTRODUCTION Seismic evaluation of an existing hospital in Long Beach, California, required geotechnical investigation followed by site-specific ground motion analysis. This evaluation was required by the Office of Statewide Health Planning and Development (OSHPD) in order to meet the requirements of the Structural Performance Category 4D (SPC-4D) published as a part of the 2016 California Building Code, CBC (Section 3412A). SPC-4D utilizes ASCE41-13, as modified by OSHPD, and involves two seismic performance objectives: BSE-1E (20% probability of exceedance in 50 years) and BSE-2E (5% probability of exceedance in 50 years). Spring constants and capacities of foundation elements were needed for evaluation of the structural performance of the building subjected to these two performance objectives. Our review of the as-built foundation plans indicated that both shallow footings and caissons were used for support of the structure. The plans demonstrated that all caissons are belled (under-reamed) and are individual, i.e. not part of pile groups. In this paper, the subject site condition and foundation elements are described first. This is followed by details of assessing spring constants and vertical capacities for belled caissons. The new requirements of the 2016 CBC concerning the evaluation of critical facilities will likely entail evaluation of other structures with belled caissons due to the more extensive use of these foundations in the past. This paper proposes a method to address the conditions of individual belled caissons not explicitly considered in the current code provisions.

Jan 1, 2018

By Harald Ludwig

In 2002, excavation support work commenced on the Capitol Visitor Center project located adjacent to the nation?s Capitol building in Washington, D.C. The outlying work (Slurry Wall Work at Main Site is not discussed) consisted of providing excavation support for a new truck tunnel approximately 1900 feet long up to 50 feet deep as well as support for the new underground auditorium and Library of Congress tunnel. The excavation support consisted of a combination of conventional drilled in soldier beams, lagging, tiebacks and braces; intricate underpinning inside the existing Capitol building; support of an existing Russell Tunnel; soil nailing and tiebacks underneath the existing Russell Tunnel; two temporary bridges; and a deep soil mixed wall with lateral support provided by braces. As part of an on-going research program, some of these braces were instrumented with strain gauges. The deep soil mixed wall was approximately 300 feet long and 65 feet deep on either side of the truck tunnel. Approximately 34,000 sf of deep soil mixed wall, 90,000 sf of conventional excavation support, 200 braces, and 320 tiebacks were installed. This paper describes the large scope and breadth of the project that required a variety of excavation support techniques. A few of the challenges in designing and installing the support of excavation are discussed. This paper also presents the results of the instrumentation program conducted on the deep soil mixed wall, which stood open for more than a year.

Jan 1, 2006