Search Documents

By Robert Fernie

Demographics and Infrastructure demands have led to a significant increase in construction of: deep basements for buildings and, trough structures for Highway and Rail/Metro. Concrete embedded walls used for temporary works can be incorporated into permanent works and because of this (and geological conditions) tend to be favoured in UK. This paper considers British practice in the provision of diaphragm (slurry) walls secant (true and pseudo) piled walls contiguous piled walls Plant utilisation, construction techniques, reinforcement placement, connections, propping, water tightness, tolerances, general UK practices and their relation to design practices are discussed. [ ]

Jan 1, 2000

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

By A. Garassino

A pile design was performed for a thermal power station in Egypt and more than 4000 piles were to be driven. Technical economical reasons suggested the choice of driven composite LACOR piles designed for very high specific loads. Some uncertainties on the behaviour of the pile soil system suggested to perform a test on an instrumented pile. Scope of the test was to verify the possibility of developping the required bearing capacity within the range of the allowable pile settlements values and the effect of the pile joint enlargement on that portion of skin friction to be developped by the upper pile section.

Jan 1, 1991

By Seth L. Pearlman

Pin Piles are small diameter high capacity drilled and grouted piles also called minipiles or micropiles. They are ideal for building foundations on sites with poor ground conditions, sensitive surroundings, restricted vertical clearance, or difficult access. They are also well suited to foundation underpinning, arresting ground movements, and increasing the capacity of existing foundations. The major factors for selection of Pin Piles are reviewed; drilling, grouting, and design fundamentals are summarized; and a major case history is presented for the underpinning of the 43 story elevator core at the recently opened Mandalay Bay Resort and Casino in Las Vegas, NV.

Jan 1, 2000

By Anburaj C., Srinivas A.

Deep excavation with support system is required to construct various part of underground structures like shafts, stations and entry structures etc. These structures have to be constructed using permanent or temporary embedded retaining walls with support system. The selection of a suitable type of retaining wall will depend upon the geological condition present in the particular location, time, cost and available equipment etc. In Bangalore Metro Rail Project, secant pile wall is adopted as the temporary earth retaining system and depth of excavation is about 20 m. It is designed initially based on bottom up construction methodology with 3 level of struts and 3 level of anchors but at later stage due to time and other construction related issues, it is decided to change the configuration to 6 levels of strut. Generally, in deep excavations, all the underground structures should be designed and checked for the critical forces from both permanent stage and construction stages. Since, secant piles are used as temporary retaining wall, only construction stage analysis is carried out to get the governing forces and deformation. In construction stage analysis, soil layers are defined with boundary conditions and the surcharge during construction and surcharge from actual building near the secant pile are considered. This paper discusses the effect of change in the support system from anchors to struts and how these changes in the support system affect the behavior of secant pile and subsequently adjacent buildings present in the influence zone of the excavation. As a result, in changing from anchors to struts, the wall displacement, strut forces and ground movement on the adjacent ground and buildings increases. The increase in deflection, ground movements and strut forces occurs during backfilling sequence of the underground station excavation. During backfilling, struts has to be removed and this imparts higher magnitude in deflection, strut forces and ground movements.

Nov 1, 2022

By D. A. Bruce

The Deep Mixing Method is a very valuable tool for combating problems related to in situ soil treatment, improvement, and retention. Many different variations are used throughout the world, and there is a correspondingly rich technical literature on the testing and properties of the treated soil. This paper provides a synopsis of these aspects.

Jan 1, 2001

By Christopher M. Kenney

Augered-cast-in-place (ACIP) piles have been utilized on commercial projects throughout many parts of the country for years, but are only beginning to be scrutinized for use on major infrastructure projects and other critical structures in some regions. Numerous engineers are aware that ACIP piles are an economical foundation alternative, and many technical papers have been presented that provide reliable methods of estimating ACIP pile load capacity. However, designers may not yet appreciate that the load-settlement behavior of ACIP piles is very similar to that of drilled shafts. This paper analyzes ACIP pile case histories from throughout the country and demonstrates that ACIP pile settlement under applied load is consistent, predictable, and very similar to the documented behavior of drilled shafts. This paper also presents a simple but accurate method of estimating ACIP pile settlement at the design load, and illustrates the need to estimate the equivalent diameter of the as-built ACIP pile when estimating pile behavior. Finally, this paper presents back-calculated values of the drained elastic modulus from the ACIP pile case histories that may be useful to those using more sophisticated methods of estimating ACIP pile settlement.

Jan 1, 2001

By John R. Wolosick

MACROPILES are defined as ultra-high-capacity micropiles, with working loads in excess of 250 tons. The piles are typically 9-5/8 to 24 inch (244 to 610 mm) outside diameter. They are drilled and grouted in place, with either large diameter steel bars and/or steel pipe reinforcement. The piles are typically tested to twice the working load. Piles with working capacities of up to 500 tons and tested to 1000 tons have been installed. The paper discusses MACROPILE design philosophy, construction techniques, and two case histories where this innovative foundation system has been installed. Macropiles are descended from micropile technology pioneered in the early 1950s by Fernando Lizzi of Italy.

Jan 1, 2006

By Magnus Ruin

The dry deep mixing method for stabilization of soft soil has been used in the Scandinavian countries for 25 years. The typical application has been stabilization of soft inorganic clay. Today the method is used more frequently in organic soil with good results. The Limix System, introduced in the USA by Hercules Grundläggning AB and TREVIICOS Corporation, is a cost-effective dry deep mixing method used to stabilize most types of soft soil. This paper presents the general principles of stabilizing organic soil with the dry mix method and two case histories of soil stabilization projects in organic soil. Between October 2000 and June 2001 the Limix System was used in England to stabilize soft organic alluvium at the Channel Tunnel Rail Link, Contract 440. During year 2000 the Limix System was used in soft organic soil in Holland near the Groene Hart Tunnel entrance to support trench excavations for slurry walls and concrete barrettes.

Jan 1, 2001

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

The Sandbukta-Moss-Såstad (SMS) project is a part of the Intercity development project, which is part of the largest transport project in Norway, consisting of 270 km of new double-track rail. The SMS project consists of 10km of double-track railway including three open stretches and two tunnels. Soil conditions consist of quick clay underlain by Bedrock. Dry soil mixing (DSM) was considered as the main soil improvement method to allow for excavation of the quick clay and construction of the D-Wall panels. The preliminary design revealed around 25,000 ton of binder installation. Therefore, a test field has been conducted to evaluate binder alternatives in means of improved soil strength by considering CO2 emissions. Multicem and Standard cement (Standard FA) have been compared for that purpose. Multicem is a type of binder which mainly consists of Portland cement and cement kiln dust (CKD). CKD is a fined-grained, solid, highly alkaline material removed from the cement kiln exhaust gases. reverse column penetration test (FOPS) and pre-drilled column penetration test (FKPS), which are common tests to evaluate DSM strength have revealed comparable strength outcome for both binder types. Therefore, Multicem has been selected as the main binder type to be used further which provided a reduction in CO2 footprint of up to 40%.

May 1, 2022

By Vijaya Bhushan Rao, Jason Redgers

A substantial lifestyle destination in the United Arab Emirates, in the Emirate of Abu Dhabi comprising of 1315 villas, town houses and non-residential leisure facilities is built over an area of 280 hectares of former mangrove areas, natural sands and reclaimed lands. Large-scale subsoil investigations including field and laboratory testing carried out dividing the entire site in to 7 clusters. This investigation revealed alternating layers of loose sands and silty clays within the load influence zone of planned foundations, showing susceptibility to excessive settlements. Therefore, ground improvement works were undertaken using a combination of stone columns, Rapid Impact Compaction (RIC) and excavation and replacement of soils plus a 0.4m thick load transfer platform. This was necessary to limit the settlements, increase-bearing capacity and prevent long-term settlements. 30 no’s of full-scale Zone Load Tests, ZLT were carried out each for a duration of 30 days in order to ascertain the anticipated long-term settlements in the clay layers. In addition, further testing of electrical cone penetration tests, CPT, and Plate Load Tests, PLT. The use of Priebe and Asaoka’s observational procedure were applied to predict the final settlements and the use of back-analysis from the 30 days Zone Load Tests, ZLT results to establish the site-specific consolidation parameters in clay layers to optimize the design and ground improvement works.

Sep 8, 2021

By B. Sivarama Sarma, Biswabikash Rout

"Seepage control has to be achieved with plastic concrete cut-off diaphragm walls in dam structures. Materials selected for construction of cut-off walls must be durable, impermeable and have stiffness comparable to the surrounding soil.Plastic concrete provides a feasible and economical solution for construction of durable and impermeable cut off walls for dam structures. Plastic concrete wall should not be understood as a concrete wall with similar mechanical properties of concrete used in buildings, piles and spillways sections. Though it consists of the same materials as those of conventional concrete it has the major differences in end product due to predominant addition of bentonite slurry in the mix with very high water cement ratio. This makes the hardened concrete with very low compressive strength less than 5MPa and high failure deformations after the peak load.This technical paper examines a case study, the typical specifications on demand for construction and the issues corresponding to misunderstanding of the material as a structural grade concrete material. Conclusions were drawn based on a few project site quality data and trial mix experimental data. The anomalies in specifications on demand for construction of curtain wall in a dam structure were removed with modifications.INTRODUCTIONDiaphragm walls which are constructed in trenches made of plastic concrete basically serve the function of seepage control under confined measures. They should have the ability to sustain and undergo large plastic strains as compared to conventional concrete. The three basic mechanical properties of plastic concrete cut-off walls are to have least permeability, minimum strength to retain its shape and ability to undergo large deformations under confined loading conditions. The constituents of plastic concrete are cement, bentonite, coarse and fine aggregates, chemical additives to improve flow of concrete and sometimes to retard the setting time and water."

Jan 1, 2017

By Anthony H. Tawil

Modern, high-speed machines used in the manufacture of paper require foundations with stringent settlement constraints. To fulfill this requirement, caisson piles, extending into bedrock, were selected to support a paper machine in Baie Comeau for the Quebec North Shore Paper Company (QNSPCo.). This was the fourth machine in an existing paper mill, and its construction was part of an expansion program which included the building of associated structures such as a wood room and chip storage building, and other facilities, Figure 1. The paper mill in Baie Comeau, Quebec, is located in an area which has extensive deposits of sensitive marine clay which are transformed into a viscous liquid when disturbed by external forces such as the driving of piles. Loss of ground and soil disturbance as affected by piling activity assumed considerable importance in the design and construction of the caissons particularly in view of the proximity of existing plant facilities, including another paper machine.

Jan 1, 1987

By Thomas L. Vande Voort

The strategic plan for bridge engineering issued by AASHTO in 2005 identified extending the service life and optimizing structural systems of bridges in the United States as two grand challenges in bridge engineering, with the objective of producing safer bridges that have a minimum service life of 75 years and reduced maintenance cost. Material deterioration was identified as one of the primary challenges to achieving the objective of extended life. In substructural applications (e.g., deep foundations), construction materials such as timber, steel, and concrete are subjected to deterioration due to environmental impacts. Using innovative and new materials for foundation applications makes the AASHTO objective of 75 years service life achievable. Ultra High Performance Concrete (UHPC) with compressive strength of 26,000 psi (180 MPa) and excellent durability has been used in superstructural applications but not in geotechnical and substructural applications. This paper explores the possibility of using precast, prestressed UHPC piles in future bridges. An H-shaped UHPC section, which is 10-in. (250-mm) deep with weight similar to that of an HP10×57 steel pile, was designed for constructability and economical reasons. Instrumented UHPC elements were cast to conduct large-scale field tests. In the field, two UHPC piles have been successfully driven in glacial till clay soil and load tested vertically. Test results, durability, drivability, and other material advantages over normal concrete and steel indicate that UHPC piles are a viable alternative to extend the life of bridge structures.

Jan 1, 2008

By Cau T. Bui

Thanks to Doi-moi (renovation) policy, many great bridges were constructed in Vietnam to meet demands of her booming economy in the recent decade and deep foundation structures were the only alternatives for the foundations of these great bridges. The deep foundation structures were constructed by modern technologies and almost of all these deep foundation structures were designed by foreign companies and carried out by Vietnamese workers and engineers under supervision of foreign experts. Beside successes, there were several failure cases in which the collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation killing 54 workers and seriously injuring 80 other workers was the most serious. This paper introduces construction techniques of the deep foundation structures applied to building of great bridges in Vietnam recently. It will especially focus on two failure cases: 1) collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation and 2) failure of drilled shaft foundation of Thanh-tri bridge due to poor construction technique and management. These two failure cases were greatly concerned by both bridge specialists and the public. Reasons of and lessons from these two failure cases will be carefully discussed. From the two failure cases, this paper will draw some lessons that should be important issues to be seriously paid attention when designing and constructing deep foundations in Vietnam.

Jan 1, 2008

By John J. Vieaux

Allowable loads on Dynamically-Cast-In-Place Piles (the Franki type) can be correlated with N values from the Standard Penetration Test. Using a constant developed by Nordlund, a conservative value for load-carrying capability of a DCIP pile is developed. The DCIP pile and method of installation is briefly described.

Jan 1, 1984

By WenJun Dong

This paper presents the stability assessment of the steel pipe piles that are used to support a deadman beam to anchor an adjacent bulkhead wall. Finite element analyses are performed to assess the stability of the bulkhead wall and determine the required tie-back force to the pile. The piles are relatively close to the bulkhead wall such that their soil resistance wedge zones are not fully developed but truncated by the bulkhead wall. The reduced lateral resistance capacity of the anchor piles is determined by applying the Coulomb wedge method on the truncated soil passive zones between the pile and wall. Both the conventional soldier pile stability (in terms of force and moment equilibrium) and Winkler soil spring (for soil-pile-interaction) analyses are used to assess the stability of the anchor piles.

Sep 8, 2021

By Robert B. Bittner

"AbstractLarge diameter tubular piles offer significant advantages in terms of design performance and economy for major marine structures. This is particularly true for foundations of major overwater bridges in regions of high seismicity such as the west coast of North America. The use of large diameter piles in the range of 2 to 3 m diameter means that fewer piles are required, and the size and mass of the pile caps can be significantly reduced, thereby greatly reducing lateral load demand during seismic events. Another advantage of using larger diameter piles is increased pile stiffness that allows the pile caps to be located at or near the waterline rather than being positioned at or below the mud line. This elevating of the pile cap offers significant cost savings by eliminating the need for deep cofferdams. However, relocation of the pile cap creates new problems and opportunities in regard to the means and methods used to construct the pile cap. With the pile cap at depth, conventional steel sheet pile cofferdams with thick tremie seals are typically used to isolated the cap location and allow dewatering for construction of the cap. However with pile caps positioned up off the bottom, conventional bottom founded cofferdams are no longer cost efficient. Float-in or lift-in cofferdams have been developed to address the need for a more cost efficient method for cap construction. This paper describes the key features of the concept and provides three case history examples of its successful implementation.Pier Construction Using Conventional Sheet-Pile CofferdamsCofferdams are temporary structures used in the construction of bridge piers and other marine structures. Their primary purpose is to hold out water and unstable soil from the construction area, and thereby, allow in-the-dry construction of the permanent structure below the water line and quite often below the mud line. Typically, cofferdams consist of long interlocking steel sheet piles driven through water into the bottom of the waterway. The sheet piles form temporary exterior walls which are typically braced internally with wales and struts. The bottom of the cofferdam is typically sealed with tremie concrete or an impervious clay layer if one exists. The depth at which this type of cofferdam can be used is typically limited by the length of steel sheet pile that can be transported and handled by conventional marine equipment."

Jan 1, 2014

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

Large diameter open-end pipe piles are increasingly used as deep foundations to support heavy onshore and offshore structures. During the driving process, several factors such as subsurface conditions, hammer type, hammer efficiency, pile type, plug conditions, temporarily increased base resistance, and loss of shaft resistance have direct impact on the driveability of large diameter open-end pipe piles. In a uniform subsurface condition, the unit shaft resistance increases with depth. Consequently, more resistance is accumulated as piles penetrate to greater depths which results in higher driving resistance. However, according to the friction fatigue analysis, the greater the number of shearing cycles occurring on a soil segment along the pile shaft, the greater the reduction of its shear resistance. As a consequence, since upper soil layers are subjected to a greater number of blows than those at greater depths, they have a relatively lower resistance compared to what would be calculated with standard geotechnical analysis methods. As a result of this progressive and nonuniform loss of shaft resistance with driving, blowcounts tend to increase at a lower rate than expected from traditional analyses. This paper discusses one of the approaches to the driveability analysis with the geotechnical friction fatigue consideration. It also shows comparisons between predicted driveability obtained from wave equation analysis and field driving records. All analyses were performed for a 2.134 m (7.0 ft) diameter open-end pipe pile installed at a total depth of 192.90 m (554 ft). Two separate static resistance and wave equation analyses were completed for the case study presented in this paper: 1) Friction Fatigue analysis based on the recommendations of Alm and Hamre (2001), subsequently referred to as the FF model, and 2) Standard Driveability analysis based on soil set- up factors, hereafter referred to as the SD model in this paper. Results from analyses included the shaft resistance distributions compared to the result of the signal matching analyses determined from the pile dynamic measurement. Furthermore, predicted blowcounts were compared to observed blowcounts during the pile driving. The comparison analyses indicated a 54.4 percent resistance loss of the Static Resistance during Driving (SRD) due to the geotechnical friction fatigue corresponding to a 46 percent reduction in total resistance. The analyses also showed that average predicted blowcounts using the friction fatigue were 6.4 percent lower than measured blowcounts, whereas, the standard driveability approach showed 42.1 percent higher blowcounts compared to the blowcounts shown in the driving log values.

Jan 1, 2019

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001