Search Documents

By Basem Sh. Hazzan

In the last four decades significant effort has been devoted to designing piles in expansive clay soils. Nevertheless, only a scant effort has been devoted to the elimination of heave forces acting on the upper part of lightly loaded piles. For this purpose, an investigation site was established in Karmiel in Northern Israel. On this site sixteen unloaded cast-in-situ piles, both uncoated and coated, were installed in a moderately expansive clay soil in the end of summer 1996. The piles were executed to different depths ranging between 2m and 7m and were observed over a period of 27 months. Another nine unloaded cast-in-situ bored piles were installed at the end of summer 1998 for carrying out pullout tests. These piles were embedded two meters from the ground surface. Results obtained from observations and from full-scale static pull out tests showed that separating the piles from the surrounding clay in the active zone by a twin walled sleeve eliminated the heave forces significantly. The scope of the work is, determining of the elimination degree of the heave forces due to the provision of the above sleeve.

Jan 1, 1999

By Tiruvengala Padma, Nilesh Naik

Piles are common type of deep foundation elements used for the special bridges, transmission towers, Jetties, and tall structures. Lateral loads on the structures can be due to either earth pressures, wind, waves, impact, moving vehicles and eccentric application of axial loads or in combination of the loads. Hence the lateral capacity of piles plays a major role in determining the pile dimensions. The laterally loaded pile analysis is a soil-structure interaction problem as the lateral capacity of pile depends on the soil strength and stiffness parameters and its reaction to the lateral load on pile. The common approach to determine the lateral load analysis of piles is the Beam on Lateral Springs Method also known as “p-y” method. In this method the pile is modelled as a beam and supporting soil is modelled as lateral springs. This study is focused on the comparison of output obtained from three geotechnical softwares namely FB-MultiPier, L- Pile and Wallap. L-Pile Software is based on Finite Difference Method, Wallap on Horizontal Subgrade Modulus Method and FB MultiPier on Finite Element Method. Pile response in terms of deflection, shear force and bending moments under vertical and horizontal loads from above three software are compared and concluded.

Sep 1, 2022

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By Mohamed A. Sakr

An experimental study on the behavior of pile group's arrangement under lateral load was carried out in the level ground and at crest of sand slope 3H: 2V. Tests were conducted on single pile and pile groups with center-to-center pile spacing of 3D. The model piles were founded in sand with relative density 25%. Several configurations of pile groups were used to study the effect of piles arrangement in the group (series or parallel) with respect to slope crest. The behavior of the pile groups in the level ground was compared with the behavior of pile groups at different configurations at the slope crest. Based on the test results, the behavior of laterally loaded pile groups adjacent to a slope crest depends largely on piles arrangement in the group with respect to direction of the lateral load. Pile groups in the level ground have more resistance to lateral loads when they are arranged in a parallel configuration than in a series, whereas the reverse is true in cases of pile groups constructed near to the edge of a slope. It is advisable to use the pile group in series arrangement for groups constructed at slope crest to minimize the effect of the ground slope on lateral capacity of piles and the occurred deflection and maximum bending moment of the lead row in the group.

Jan 1, 2010

By Mitsuhiro Shibazaki

Generally, water-soluble polymers are effective in convergence of water jet ejected from a nozzle as they add viscosity to water. However, excessive additional polymers (added to keep water viscous) could increase friction on the contrary. Therefore, we have totally modified the jetting system from every possible aspect, such as the shape and upstream conditions of a nozzle in order to keep the flow spread to the minimum as stated in my presentation.

Feb 10, 2003

By B. C. Slocombe

A large derelict inner city site was regenerated for use as a distribution warehouse. Difficult topography and soils conditions required the adoption of a combination of specialist geotechnical processes. Particular attention was paid to the preparation of the site, programming and capabilities of each technique as additional soils information became available.

Jan 1, 1989

By Damian R. Siebert

Risk-reduction measures implemented during the design and construction of a 21-story pile-supported building adjacent to a below-grade 100-year-old sewer structure were keys to a successful foundation system. Avoiding damage to the existing sewer structure during construction activities and the future ability to access the structure post-construction were the main concerns for the utility owner. Clear communication and a deliberate design process between all parties ? utility owner, building owner, structural engineer, geotechnical engineer, architect, and contractor ? were integral to the project?s success. This collaborative process helped all parties to understand the risks, both real and perceived, and to develop mitigation measures to reduce the risks. Bringing together all parties to engage in dialogue and encouraging open communication throughout the project were paramount to its success. By implementing the joint design plan, using mutually-acceptable construction techniques, and careful monitoring, the building foundation was successfully installed and all parties? risks were averted.

Jan 1, 2011

By Paul J. Sabatini, Yazen A. Khasawneh

"A Demag CC1800 crawler crane was partially erected on crane mats adjacent to a seawall when settlements near a corner of the crane mat area were observed to be slightly larger than previously assessed. A ground improvement program including installation of dry soil cement mix (DSM) piers was implemented to improve soil bearing capacity. Due to near-surface obstructions, only 75 percent of the DSM piers were installed to the design depth. Because of the partial installation of the DSM piers, an evaluation of the crane pad stability and the effect of the crane loading on the stability of an adjacent 10-ft high concrete seawall, which was believed to have limited (if any) reserve capacity, was required. A two-dimensional finite element model was developed to evaluate the responses of the partially improved ground and the sea wall to the loads imposed by the crane. Geotechnical site investigation and laboratory testing programs were performed to better define the subsurface conditions near the area where settlements occurred and to provide the required mechanical parameters for the soil constitutive model. Analysis results indicate that total and differential settlements of the crane pad and the increase in load on the seawall were tolerable provided limited excavation and replacement of weak dredged soils outside the DSM area would be implemented.INTRODUCTION & BACKGROUNDA Demag CC1800 was erected on 8 ft × 16 ft crane lattice mats at about 12 ft from an existing seawall. Approximately 3.5 in. of subsidence was observed at one corner of the crane mats, while the crane was partially erected and stationary. The approximate location of the crane mats with respect to the existing seawall when the subsidence occurred is shown on Fig. 1.The seawall consists of a reinforced concrete wall connected by reinforced concrete bents to a composite section of sheet pile wall; the total depth of the seawall is about 29 ft. The bents are spaced at about 20’4” and supported by five piles at each bent location. The composite sheet pile consists of concrete and a sheet pile section with a reinforced concrete wale section. The retaining wall is about 10 ft in height and is supported at three levels. The first support level comprises a 2-½” diameter steel rod near the top of the wall spaced at 40’8” the second and third level supports comprise 1-½” diameter steel rods spaced at about 5’6”. The second level support is inclined at about 10 degrees below horizontal and the third level support is oriented horizontally through the wall footing. A schematic of the seawall section is shown on Fig. 2.A geotechnical site investigation was implemented soon after the subsidence was observed. The program included advancing four borings to a depth ranging from 16 ft below ground surface (bgs) to about 30 ft bgs. In general, the investigation showed sandy material (likely fill that was used behind the retaining wall) from the ground surface in two borings located immediately behind the retaining wall. The other two borings furthest from the retaining wall showed very soft to soft clay (possibly dredged material) from the ground surface to a depth of about 10 ft bgs. Based on this information, the ultimate bearing capacity of the subsoils was estimated to range from 1,200 to 2,000 pounds per square feet (psf). From the anticipated crane loading (weight of the crane and loading lifts), a minimum allowable bearing capacity of about 1,500 psf would be required for safe operation. To achieve the required bearing capacity a ground improvement program was selected and implemented."

Jan 1, 2017

By Sridhar Krishnan

This paper presents the results of a comprehensive pre-production pile testing programme for the US$ 800 million 1400MW Coal-Fired Jimah Power Plant Project in Negeri Sembilan, Malaysia. The testing programme included high-strain dynamic testing and fully instrumented static axial and lateral load testing of driven prestressed concrete piles and bored cast-in-place piles. A highlight of the testing programme was the pioneering use of the Global Strain Extensometer (GloStrExt) Method, a deformation monitoring system that uses advanced pneumatically- or hydraulically-anchored extensometers and a novel analytical technique to monitor loads and displacements down the shaft and at the toe of driven prestressed concrete piles. The experience with the testing programme for the Jimah Project also demonstrates the possibility of achieving notable breakthroughs, not only in the monitoring, evaluation and reporting of pile foundation behaviour dynamics but also in our understanding of the mechanisms that underpin such behaviour. These significant gains are undeniably a direct result of the committed and co-operative relationship among the project owner, design/builder, specialist piling subcontractors, pile suppliers and pile instrumentation and testing specialists.

Jan 1, 2006

By Lucien Weber

In the Shanghai area, the soil conditions are such that bearing piles have become an essential foundation part of the new highrise buildings. In order to reduce the settlements under the high working loads of about 2300 kN/pile, the Chinese building authorities require the pile tip to penetrate into the compact sand layer, situated at approx. 60-70 m depth. No H-piles have yet been tested under these conditions in Shanghai. This paper describes the driving of 8 H-bearing piles with 4 different shapes and with lengths varying from 45 to 75 m. Dynamic measurements are performed during driving and after a wait time of approx. 40 hours in order to assess the change in bearing capacity in function of time and in order to get an idea about the resistance distribution along the piles by using a stress wave analysis program (CAPWAP). One pile is equipped with channels between the flanges for executing verticality measurements with an inclinometer. However, this test has not yet been performed. One month after driving, two piles of 75 m length are statically loaded both in vertical and in horizontal directions.

Jan 1, 1987

By Jr. D'Angelo, Michael M. Blendy, Shawn Downey

"A grouted helical pile was used to support new buildings in the reconstruction of a large residential development. Foundation options were complicated by urban fill underlain with variable alluvial soil. A driven timber pile and grade beam system was recommended to support the new buildings. Other foundation options are also discussed. The grouted helical pile was quoted as an alternate and ultimately won the bid based on the economics and performance of the system. Data from 8 load tests was used to develop an empirical site specific relationship for determining pile capacity based on both installing torque and installation depth. Design to incorporate tolerance on installed pile location is presented. With the three phases completed, 554 residential dwelling units supported by 3645 grouted helical piles had been constructed covering 18 city blocks on the 44 acre site. IntroductionThe Philadelphia Housing Authority reconstructed the Tasker Homes housing complex located in southern Philadelphia, Pennsylvania, adjacent to the Schuylkill Expressway in the Grays Ferry area. Keating Building Corp. and Pennoni Associates were the general contractor and the structural engineer respectively. The original Tasker Homes development was constructed from 1940 to 1941 and consisted of 44 acres of primarily two and three-story residential brick buildings. These buildings were supported by a timber pile foundation system. The structural condition of the buildings supported on the timber piles was generally good in comparison to areas outside the buildings. These areas had settled possibly up to 2-feet in places due to the heterogeneous nature of the urban fill."

Jan 1, 2005

By Jamey Rosen

A Project Information Management System (PIMS) was developed to manage and analyze QC data at the Herbert Hoover Dike Rehabilitation Dam Modification Cutoff Wall (owned by the Jacksonville District of the United States Army Corps of Engineers). A special feature of this PIMS was its geospatial component. Data collected from Bauer drill rigs were automatically “geoprocessed” into threedimensional features representing the predrill, jet grout, and Cutter Soil Mixing panel elements, as well as calculated verticality and overlap metrics. These features were visualized in interactive planimetric, profile, and 3D views that facilitated several quality control activities during the project.

By Adriaan van Seters

"Abstract The content of Eurocode 7 – Part 1 and Part 2 – with respect to piled foundations is outlined. The important role of pile testing is presented and the derivation of the characteristic value of pile bearing resistance is explained. Recommendations for the use of correlation factors are given. The ongoing work of the Evolution Groups on piling is to prepare a revision of Eurocode 7 after 2019. Future topics and changes are highlighted.General outline of pile design by Eurocode 7In his paper for this conference Frank (2014) outlined the various aspects of standardisation for pile foundations, which involves Eurocode 7 as leading for pile construction in Europe. Standards for pile testing and execution of piling works were established in the last 15 years.This paper focuses on the design of piled foundations according to the design code Eurocode 7, which consists of 2 parts:EN 1997-1 Geotechnical design - Part 1: General Rules (CEN, 2004);EN 1997-2 Geotechnical design – Part 2: Ground investigation and testing (CEN, 2007) In Eurocode 7-1, Section 7 – Pile Foundations - deals with the design of piles. The safety concept for pile design is given in Section 2 – Basis of Geotechnical Design - for the three Design Approaches.In Section 7 presents the design of piles according to four methods:1. Results of static load tests2. Empirical or analytical calculation methods3. Results of dynamic load tests4. Observed performance of a comparable pile foundation.Guidelines for the ground investigation for piles is provided in Eurocode 7-2, Annex B.3. In the Annexes of Eurocode 7-2 examples of analytical methods to determine the bearing resistance of a single pile based on the results of various ground investigation techniques are given. Thus calculation models are presented based on design using the results of Cone Penetration Tests (D.6 and D.7) and Pressuremeter Tests (E.3). The Annexes of Eurocode 7-2 are informative.For the interpretation of Eurocode 7, reference is made to Frank et al (2004) and Bond and Harris(2008)."

Jan 1, 2014

By Cassandra A. Wetzel

Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.

By John S. Pack

The application of square shaft helical piers in expansive soils is a standard of practice in many areas of the United States. Over 20 years of performance monitoring show exceptional performance and economy will result if proper design procedures, specification requirements and installation procedures are followed. This is true for new foundations and the repair of existing foundations, including lightly loaded wood-frame structures on expansive soils. Proper design includes: 1) site geotechnical characterization, 2) pier layout such that each pier is loaded to its maximum design capacity, 3) maximize spans between piers, 4) minimize the number of piers, 5) isolate the structure from the expansive soil with an appropriate void zone below all grade beams, slabs or other components that would otherwise be in soil contact and 6) utilize only single helix piers. Proper specification employs a performance specification that specifies: 1) the design load on each pier with a suitable safety factor, 2) the minimum installation torque, typically 4,000 ft-lbs (5.4 kN-m), or refusal, 3) a minimum pier shaft steel Fy = 70 to 90 ksi (483 to 621 Mpa) and pier helix steel Fy = 80 ksi (552 Mpa), 4) 1.5 to 1.75 inch (38.1 to 44.5 mm) square shafts, 5) smooth shaft surface, 6) the ICC Evaluation Report (ER) number of the manufacturer and 7) the manufacturer ISO 9001 certification for material quality control. Proper installation requires: 1) equipment with sufficient axial compression force (crowd) on the pier shaft so the helix engages the soil and advances to the specified minimum installation torque or refusal, 2) additional specialized techniques for expansive soils and 3) qualified specialty helical pier installation contractors experienced in expansive soils who submit and utilize pier configurations, techniques and equipment that will most effectively and economically meet the specified performance.

Jan 1, 2007

By S. L. Karunakaran

Selection of an appropriate foundation system requires great skill and ingenuity on the part of the designer. Certain guidelines for choosing between a pile and raft foundation are presented. A number of methods are available for estimating the capacity of piles, giving a wide range of values for the theoretical load carrying capacity. A few aspects to be taken into account while arriving at an appropriate theoretical capacity are discussed. The effect of fluctuation of water table level on the pile capacity and method of accounting for this factor on the pile capacity obtained through initial load test are also discussed. A case study presents a comparison between the estimated values of capacity of piles and the values obtained through the initial load test.

Jan 1, 1996

By Piotr D. Moncarz

As major urban areas begin to run out of "good-terrain" for their expansion, they begin to claim high water-table areas within or adjacent to water fronts or swamps. Similarly, major infrastructure projects encroach on or cross high organic content areas. The associated major structures often require deep foundations located in soils investigated through core samples removed at a discrete number of locations. The investigation is nearly always preoccupied with soil mechanical properties, sometimes with soil non-organic chemistry for concrete and metal corrosion, seldom, if ever, for organic-chemistry and bio-conditions as related to concrete longevity. Not surprisingly so, bio-corrosion of concrete is one of the least understood phenomena by practicing civil engineers. This paper shows how low-iron, organic-rich sediments may trigger sulfate degradation of concrete, even when standard pre-construction chemical analyses indicate only a moderate sulfate level. The discussion is illustrated with a case of a pile foundation in the United States driven into marine channel sediments and sediment-derived fill material. The concrete piles lost their structural integrity due to secondary ettringite formation and depletion of iron in the cement paste. Disintegration of concrete occurred only where it contacted superficial marine sediments and sediment-derived fill material. Concrete in direct contact with seawater or native sand and silt materials appeared to be sound. Sediments in contact with the degraded concrete were highly anoxic and had a history of sewage contamination, contained low concentrations of total iron (<2%), Fe(III) (<0.3%) and moderate levels of sulfate (1500ppm), and exhibited high bacterial activity. This environment resulted in the microbial dissolution of Fe(lll)-rich ferrite in hardened cement paste. Iron depletion in the cement paste had made the concrete vulnerable to degradation by sulfate, even at moderate levels of sulfate concentrations in the sediments.

Jan 1, 2002

By Rangaswamy. K, Naga Sivaji

A stone column is one of the most commonly employed methods of ground improvement techniques. This method used to increase the strength, decrease the compressibility of loose granular and finegrained soils. Also, it accelerates the consolidation in clays and reduces the liquefaction potential of sands and silt soils. In general, the stone column contains 15 to 75mm stone aggregates. In reality, it is not easy to avail the natural stone aggregates due to unavailability in locally nearby places. Present work aims to replace the stones partially or entirely by scrap tyre chips as an alternative material. The utilisation of recycled tyre chips in ground improvement is an environmentally friendly solution and avoid the disposal of tyre chip waste in large pits. Model tests conducted on marine clay with encased end bearing stone columns (ESC) constructed with a mixture of stone aggregate and tyre chips with sizes 4.75 to 10mm. The column diameter is 75 mm, L/d ratio maintained to 5.3. Non-woven geotextile wrapped encased stone column has introduced in the soft marine clay model. Encasement prevents the lateral squeezing of aggregates into the surrounding clay and protects the drainage function of the stone column. A set of load-settlement tests were conducted on both the clay model and clay model treated with the stones-tyre chips column. The model was loaded by the tri-axial loading frame. Shear strength parameters of stones and tyre chips were determined by large size direct shear tests. Model test results are concluding that the load-carrying capacity of the clay is improved significantly after installing the stone column in it. The encasement increases the load-carrying capacity and stiffness of the ordinary stone column. It is also proved that the stone aggregate could be replaced partially by tyre chips up to 60% without a significant reduction in its performance.

Nov 1, 2022

By P. V. Chandramohan

"The paper deals with the arrangement of structural members for a retaining structure used as a berth in the port of Krishnapatnam. The height of retention is 24.3m. A T-shaped diaphragm wall acts as the retaining surface. A relieving platform has been provided at the top to ease lateral earth pressure on the wall. The diaphragm wall is tied back to a combination of vertical and raker pile. Later, this arrangement was altered to replace the relieving platform with just lowering of ground level below the berth. The tie back was changed to a classical A-frame anchorage. At certain reaches, installation of piles pointing towards the rear was obstructed by a conveyor structure. The anchorage was then changed to include a vertical pile and a pile that points towards the front of the berth. Change in position of inclined pile alters the force in the pile from compression to tension.GeneralPort is a major link in the multimodal transport chain. Berth is the heart of the Port infrastructure. It is here the ocean freight changes to land transport. The change-over, warrants special type of heavy duty handling equipment. The equipment and the process necessitate deep seated foundations. On one side of the berth, deep drafted ships would be berthed. But adjacent to this heavy duty cranes would be operating at the deck level. Berths are of various types. Some are founded on piles and may project into water. Some operators prefer a retaining structure. At the port of Krishnapatnam, a retaining structure was preferred. Dredged level at the berth was to be -20. Deck of the berth was at +4.3. This meant that the height of retention of soil was 24.3m. Ports are generally located near the coast. Subsoil in the port area generally consists of cohesive material of low shearing strength. The berth has to cater to imposed vertical and horizontal loads.Structural functionFor bulk cargo and containers, berth has to support the two crane tracks. These tracks will carry heavy wheel loads of the crane. Besides, the space between the tracks would be used for stacking of cargo or hatch covers. In short, the deck will be subjected to heavy surcharge. This vertical load will manifest as additional lateral force on the retaining wall. Since the height of soil to be retained is high, it is a practice to relieve the lateral earth pressure due to the heavy surcharge of the wall. This is done by providing a relieving platform. The surcharge of superimposed load on the deck and the self-weight of the soil up to a few metres below would be relieved by a suitable platform. This vertical load would be transferred directly to deeper levels through piles. Mooring pull is a horizontal force exerted by the vessel on the bollards towards water side. Berthing force is exerted by the vessel during berthing, through fenders and acts towards land side.Diaphragm walls are usually employed as the retaining face. If the height of retention is less, these walls can cantilever out but in the case of large retention, they have to be tied back. The ties are to be anchored on to suitable arrangements like a dead-man or an A-frame. Berthing structure in the early stages at Krishnapatnam port is shown in fig 1."

Jan 1, 2015

By Osvaldo Valdez, Matteo Bertoni, Aem Ragy

The East St. Louis Deep Cutoff Wall project is located in the area of East St. Louis, Illinois, across the Mississippi River from the city of St. Louis, Missouri, along the left descending bank of the river. The project is a fundamental part of the U.S. Army Corps of Engineers' (USACE) effort to rehabilitate and secure the aging East St. Louis levee system that provides flood protection to approxi- mately 250,000 residents and more than $4.5 billion in economic value. The project was devised and de- signed by USACE as a cutoff wall to be installed in the Metro East Sanitary District levee segment, one of the levee segments that form the East St. Louis system. The contract for the construc- tion of the cutoff wall was awarded in November 2019 to Bauer Foundation, the American subsidiary of the Bauer Group.

Sep 1, 2023