Search Documents

By Adel Hanna

Earth pressure acting on piles driven in sand is playing a major role in estimating pile capacity. In literature, researchers entertained simplifying assumptions in estimating the earth pressure acting on the pile's shaft, ignoring the effects of pile installation and pile size. Empirical formulae were introduced based on laboratory or field test results, where major discrepancies can be found among these formulae. In this paper, the theory of cavity expansion and the finite element technique will be used to establish the effects of pile installation technique and pile's diameter on the earth pressure acting on the pile's shaft and accordingly on the values of the existing coefficient of passive earth pressure and overconsolidated ratio. It is of interest to note that pile driven technique and pile's diameter have significant increase on the earth pressure acting on the pile's shaft and accordingly on the overconsolidation ratio in case of loose or medium sands, while they may cause crushing and dilation in case of dense sand. Keywords: Single pile, Cavity expansion, Cohesionless soil, Driven piles, Numerical modelling, Finite element technique, Earth pressure.

Jan 1, 2003

By H. Mori

Construction of cast-in-place piles with enlarged bases has become popular in the cities in Japan facing to the sea coast, where the subground soil is soft alluvium deposited to depths often exceeding 30 m. The groundwater table is a few meters below the ground surface. Skin friction of piles may become negative due to ground subsidence or reduced due to liquefaction of loose sand during an earthquake. To support highrise buildings, depths of bearing strata to which piles are embedded often exceed 50 m. Due to such geotechnical conditions, methods and equipment to build cast-in-place concrete piles mainly built by the reverse circulation method have been developed since the 1970s. In the first half of this paper, the authors review the cur-rent practise of building cast-in-place piles with enlarged bases. Then they introduce the TFP system developed in recent years, and discuss about the procedures to control and monitor enlarging of bases.

Jan 1, 1989

By Wen-Chieh Cheng

Two bored piles with base grouting are loaded axially and the results are used to compare with numerical analyses. One compressive pile with a diameter of 2 meters is drilled through clay deposit and into bedrock to a depth of 13.7 meters. One tensile pile with a diameter of 1.5 meters is drilled through the same clay deposit and into bedrock to a depth of 17 meters. Both piles are installed with monitoring system such as rebar strain meters, concrete strain gauges and extensometers. The monitored data during pile load test are used to obtain average frictional stress (t) a displacement (z) curve, pile tip bearing (q) as well as pile head load (p) and a displacement (s) curve. FLAC3D is used to simulate the pile loading and base grouting. The soil and bedrock are modeled with Mohr-Coulomb. The parameters of the constitutive law are established from soil biaxial tests and rock bore hole deformation tests. The pile is assumed as an elastic body. The interface element is used to simulate the pile/soil interface and pile/rock interface. The numerical results are compared with the pile load test in terms of t-z curve, q-z curve and p-s curve. Finally, the pile base grouting is simulated and the uplift is analyzed. The result from this study is promising and the numerical modeling is successful.

Jan 1, 2006

By P. B. Kelleher

Most of the piers and other pile-supported marine structures in the New York City Harbor area were constructed prior to the widespread use of currently available pile protective systems. As a result, the support piling of many existing marine structures have experienced deterioration to an extent that their structural sufficiency is impaired long before the useful life of the structures they support is over. This situation presents special and unique problems of how to restore the structural integrity of these piles while at the same time allowing full use of the structures they support. Spearin, Preston & Burrows is a 100 year old New York City-based marine construction firm specializing in waterfront and foundation construction. In recent years it has undertaken and successfully completed several unusual projects in the New York City Harbor area involving the rehabilitation of existing, deteriorated piling underneath major, economically important marine structures. This work was accomplished using techniques that permitted full use of these structures. Several different pile rehabilitation systems were used, each having their own particular application to the deterioration problems of the piles supporting each structure.

Jan 1, 1989

By Timothy C. Siegel

Drilled displacement piles (also known as augered cast-in-place displacement piles or augured, pressure grouted displacement piles) are installed by the displacement of soil and subsequent placement of fluid cement grout within the evacuated volume. Depending on the soil grain-size characteristics, soil behavior, in situ soil density, pile spacing, and pile diameter, the installation process can result in measurable densification and an increase in lateral stress. This paper examines the conditions prior to and following the installation of drilled displacement piles at sandy sites using the cone penetration test. The data support that the installation of drilled displacement piles results in a substantial increase in tip resistance.

Jan 1, 2007

By Hajialilue Bonab M.

The soil-pile interaction under lateral impact loads is not yet completely well known. Many tests on single piles under static lateral loads in centrifuge have been performed and P-y curves have been determined at different levels of the pile in soil. Following these static tests on piles, a large program is undertaken with the same piles submitted to impact loads. The pile equipped with various pile caps has been impacted under variable amplitudes of shock. The behavior of the pile under different impacts was studied and dynamic parameters of the soil-pile system have been determined. Many cases of loading constituting various load histories have been analyzed. They are resulting from parametric centrifuge tests run out, on the one hand with constant and cumulative impacts and on the other hand, variable and cumulative ones. The Influence of each type of loading was studied. Using a finite element method, a non-linear pile-soil system was conceived and a transient dynamic analysis have been performed. The results of the non-linear analysis and experimental data were compared giving a good agreement.

Jan 1, 2002

By Willie M. NeSmith

Cast-in-place piling are a staple of the deep foundation industry, and are used (in various forms) worldwide. In assessing the application of cast-in-place piles, it is of value to reflect on the development of the various systems, in order to understand how the current processes and equipment came to be. This paper traces the evolution of the cast-in-place industry. Emphasis is on developments in the United States; however, since there has been a substantial fusion of US and European processes, notable European developments are also discussed.

Jan 1, 2006

By Shinji Sassa, Naoki Takahashi, Eiji Kohama, Wakaki Tsuda, Hidenori Takahashi, Ikuo Towhata, Yoshiyuki Morikawa

"Abstract Deep mixing method has been employed increasingly in recent years as a countermeasure against subsoil liquefaction. Column-type solidification, however, has been thought to have little effect as a liquefaction countermeasure, because the shear deformation of unimproved soil between the columns cannot be reduced. In recent years, experimental results have been reported that imply that solidified columns can reduce the shear deformation of unimproved soil around them. A new arrangement has been proposed to mitigate lateral flow induced by liquefaction. In this study, a series of dynamic centrifuge model tests was conducted to verify the lateral flow resistance of stabilized columns. The results indicate that stabilized columns can reduce the lateral flow of liquefied ground if the column displacement and the column head rotation are restricted. This paper concludes that it is important to restrict the displacement and the rotation of the column head by surface improvement to mitigate the lateral flow of liquefied ground.INTRODUCTIONDeep mixing method has been employed increasingly in recent years as a countermeasure against subsoil liquefaction. The solidified body formed by the deep mixing method is usually block or lattice shape, composed of solidified columns that overlap each other horizontally. Lattice-type solidification has been shown to be effective as a liquefaction countermeasure despite the presence of unimproved soil inside the lattice wall, because the shear deformation of the interior soil is restrained by the wall (Suzuki et al., 1989). On the other hand, it has been thought that column-type solidification cannot reduce shear deformation of unimproved soil around columns, because the displacement of a solidified column is less restricted than that of a lattice wall. Column-type solidification has been reported to have little effect as a liquefaction countermeasure, but to be superior in terms of construction cost and applicability around existing underground structures (Koga et al., 1986). However, there are experimental results implying that solidified columns have reduced the shear deformation of unimproved soil and mitigated its liquefaction (Yasuda et al., 2003; Tanaka et al., 2003). Yamamoto et al. (2006) conducted dynamic analyses of ground improved with lattice- and column-type solidification. Their results showed that column-type solidification with an improvement ratio of more than 35% reduces excess pore water pressure generated by earthquakes. Furthermore, the new column arrangement shown in Figure 1(a) has been proposed to mitigate lateral flow induced by liquefaction. It was developed and has been verified using dynamic model testing in a 1 g field (Takahashi et al., 2010a; 2010b; 2013; Towhata et al., 2010). The stabilized columns in this configuration interrupt lateral flow in any direction, unlike those placed in square and triangular arrangements."

Jan 1, 2014

By Masakazu Takano, Koji Suzuki, Naotoshi Shinkawa

"Cement deep mixing (CDM) method successfully applied to a marine construction project in northern Vietnam is reported. The method is classified as wet method, in which cement slurry is injected into the ground. Thickness of clayey deposit subjected to improvement is from 20 m to 28 m, and the total volume of CDM improvement exceeds 460,000 m3. This is the first massive application of CDM method in the region. Three CDM barges, each equipped with four mixing shafts, were brought to the site in order to finish CDM work within a period of seven months. Cement content used in the work was 180 kg/m3 and water-cement ratio of slurry was 100%. Unconfined compression strength of stabilized soil was 1,200 kPa to 1,600 kPa in average with coefficient of variation from 0.3 to 0.4. Statistics analysis of the strength with these values gave percentage of lower strength less than 10%. Trial use of needle penetration test performed to study strength profile of a CDM column is also reported.INTRODUCTIONThe site of Lack Huyen Port Infrastructure Construction Project is located in the sea adjacent to Cat Hai Island, offshore Hai Phong city which is around 100 km east of Hanoi, the capital of Vietnam. Left side of Fig. 1 shows the location of the site. The project contains development of container terminal, dredging of waterway, construction of sand protection dyke to prevent waterway from being buried, and bridge construction to connect the island to the mainland.Joint venture of Penta Ocean Construction and Toa Corporation was awarded Package 6 of the project, in which reclamation of container terminal area, retaining wall construction and terminal road construction were included. Plan of the site is presented in right side of Fig. 1. The site work has been started in June 2013 and is scheduled to finish within 4 years."

Jan 1, 2015

Caissons hand dug to a depth of about 100 feet were used to underpin three important structures at an industrial site in the State of Utah. The caisson shafts extended through 30 to 40 feet of coarse, granular soils and 25 to 60 feet of sands and clays to bear on a very dense, coarse gravel and cobble stratum near the water table. The shafts were belled to 12 feet square at their bearing elevation. Bearing pressures of 20 ksf were assigned. The shafts were lagged with timber. The use of hand-dug caissons allowed continuous operation of the facility during underpinning. Settlements after underpinning have been minor and well within the estimated magnitudes. Instrumentation was placed in two of the caissons with varying degrees of success.

Jan 1, 2010

By Wang Mingshu

The pile foundation is a kind of advanced foundations in the filled or soft soil. In this paper, through the actural engineering of coal dressing plant of Western Opencast Coal in Fushun built on the mining dump with large diameter pile foundation, the construction method and mechanics analysis of pile are given. Unless it is in following stadge, the stability of pile cannot be lost due to its small rigidity. The analysis shows that pile foundations of large diameter ellipse section can decreased hotizontal displacement to 60% ?70% of that of equal section an in the design of a single pile and a single column, the ellipse pile and manual dig hole are most favourable. So a large amount of concrete can be saved.

Jan 1, 1991

By Madhira R. Madhav

In an alluvial deposit consisting of layers of sandy silt with clay and kankar nodules, driven cast in situ piles are provided. The piles end on a stiff bearing stratum To verify the available design capacities, compression, pull-out and lateral load tests are conducted in situ. The elastic continuum approach is used to estimate the equivalent modulus of deformation of the deposit. A comparison is made of the values from the three types of tests.

Jan 1, 1996

By R. G. Shen

The relation curve of strain and acceleration is presented in this paper. The steel pipe pile of 609.6 mm in external diameter driven by IDH-45 diesel motor hammer on the esturial shoal of Yangtze River. The ultimate bearing capacity of pile is analyzed by one dimensional wave equation and the effect of computational parameters of the equation is discussed.

Jan 1, 2010

By M. Nomura

This paper describes the results and field measurements of two long-term observation tests and two short-term loading tests to confirm the effectiveness of NF piles in reducing negative skin friction. All the test piles were equipped with strain gauges, allowing measurement of the compressive axial forces in the piles. These test results prove that NF piles are effective in reducing the negative skin friction to an insignificant value. Some examples of the design procedures used in Hong Kong and Japan are also presented.

Jan 1, 2010

By Farhad Elmi

In this paper, a new procedure is used to find the bearing capacity of single piles and cone penetration resistance in soils. Although the procedure is mainly applicable to clay and sand using any plasticity model, this paper deals only with steady penetration in Sand. Cylindrical cavity expansion around the probe in a calibration chamber is modeled by finite element method using the HUJEUX elasto-plastic multi-mechanism model. The penetration resistance (qc) is related to cylindrical cavity expansion pressure limit (pL) using the method of Salgado et al. (1997). This procedure is tested using the results found in 3S/IMG calibration chamber. In this article the word "penetrometer" refers to both pile and cone.

Jan 1, 2002

By Peter J. Jancich

This paper describes the installation of high capacity Augered Pressure Grouted piles which support structural loading from a four level parking garage in west-central DuPage County, Illinois. The subject site is characterized by a variable glacial geology which presented, to the designer, a number of problems with respect to analysis and prediction of pile capacities, and, to the contractor, the very real difficulties associated with estimating the costs of, and installing foundation units in highly variable subsurface conditions. 2. General Site and Subsurface Conditions 2.1 Site Conditions - The subject site is part of an overall 300 acre property. Topographically, the overall site is saddle shaped with higher elevations along north and south boundaries and a subdued, east-west trending swale centrally located. Elevation relief is on the order of 25-30 feet (7.6-9.2m).

Jan 1, 1991

By Cen Guoji

The foundation of bored pouring concrete pile have been adopted in the bridge engineering of China since early in the sixties. They demonstrated tremendous technical advantage and achieved notable economic benefit. With improvement of bridge technique including construction technique work equipment, design theory, examination in quality and applicable range etc, the pile diameter became bigger and the foundation changed from shallow to deep-water. This paper examples Jiujiang Bridge of Guangdong in China, which is single-tower cable-staged bridge, total length of 1675m, and expouds adopted successfully the foundation of variable section large bored pile (upper part d=3m, central part d=2. 4m and lower part d=2m) on the conditions of complicated technique that the load is tremendous (it require specially to resist 12000 kN ship impact) and the piles have free length 30m. The paper will be to describle design project and construction practice of pile foundation with variable section, and to compare schemes of equal section pile and pile in sinking-well.

Jan 1, 1991

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

By R. L. Wei

The disturbing influences of pile driving on the surrounding soil mass, including the induced vibration, pore pressure and displacement of soil, were observed during the construction of pile foundations. It is shown that the effects of pile driving in saturated soft clay are tremendous and ought to be concerned attentively.

Jan 1, 2010

By Kelvin Lo, Erwin Oh, Darren Newel

The use of interface elements is widespread in most numerical methods to separate the structural elements from soil elements. It allows slipping and gapping or overlapping between the two media in contact with highly distinct deformability characteristics, such as piles and retaining walls. However, many existing analytical methods still assume no pile-soil slipping before failure in axially loaded piles. This paper attempts to compare the slipping and non-slipping analytical models by introducing an interface with a virtual thickness. Results show that both have different load-displacement characteristics when comparing to the measured data. The non-slipping model would result in a stiffer load-displacement curve if the same input stiffness parameters applied to both models. Different procedures to calibration the input stiffness parameters in slipping and non-slipping models are recommended.