Search Documents

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By William F. Starke

"The Ontario College of Art & Design (OCAD) located in Toronto, Ontario, found itself in dire need of space due to increased enrollment, leading them to embark on a major expansion and redevelopment on campus. The expansion entailed an additional 115,000 sq.ft. (10,700 m2) and a new major structure was required, as well as extensive redevelopment of existing buildings. The new Sharp Centre for Design was designed by acclaimed British Architect Will Alsop, of Alsop Architects, in a joint venture with Toronto-based Robbie/Young + Wright Architects. The OCAD campus is cramped for space and the design selected was a structure built over top of existing structures. The building has been described as resembling a “shoebox in the sky”, supported on raked columns transmitting high lateral forces as well as compression load to the foundations. There are 12 such supports, each supported by an individual caisson. In addition, the project entailed installation of other caissons in the courtyard area with the construction work accomplished under very confined conditions among the existing structures. The remarkable design for the new Ontario College of Arts will surely make it another of Toronto’s architectural landmarks. Several things make this project stand out as a unique deep foundations project.First is the architectural design. Words cannot do it justice: the picture is the only effective way to start to describe it. This is a big two-story box, built over the top of a fragile existing building. The underside of the box is 86 ft (26m) above street level. Students remained still inside the old building while construction was going on around and above them. There were serious concerns about vibration – not only its effects on the academic life; but more significantly, upon the stability and safety of the old building, which rests somewhat shakily on shallow spread footings.Steel stilts that look like toothpicks when scaled against the new and existing structures support the box. The stilts are much sturdier than they appear from the pictures, but it is easy to visualize the complexity of the loads they transfer to the foundations below."

Jan 1, 2004

By Waddah Akili

At an offshore site along the Red Sea coast of Saudi Arabia, marine structures were supported on tubular steel piles driven into coral and coral contaminated sands and silts. Surprises and disappointments faced during the installation of the piled foundation were, to a large measure, due to inappropriate design methodology and absence of proper soil information. The paper describes the design evolution process, highlights the static pile test program conducted to verify design parameters, and amplifies the need to prepare for worst possible scenario when coral deposits are encountered. Despite corrections made to the design, based on site-specific insitu parameters (skin friction, end bearing) perceived from load tests conducted on site; the final design adopted overestimated capacities in over 50 percent of total piles driven. The paper describes the changes introduced to the design during the execution of the project, highlights the pile test program conducted to verify the design, and compares pile design penetration with actual penetration depth. The unpredictable and erratic pile behavior observed, ascertains the need for more appropriate pile design and installation guidelines for driven piles in coral and coral contaminated formations.

By John A. Egan, Nathaniel Wagner, Micaela Largent, Jonathan P. Stewart, Debra Murphy, Jeremy Butkovich

The Millennium Tower is a 58-story reinforced concrete building that was constructed in San Francisco, California between 2005 and 2009. The Tower is founded on an embedded pile supported mat with pile tips bearing in dense marine deposits that overlie an over-consolidated marine clay layer known locally as Old Bay Clay. This clay layer experienced stress increases from Tower self-weight and from multiple episodes of de-watering between 2006 and 2018 at the Tower site and neighboring sites. Settlements of the Tower foundation have been measured since 2006 and lateral deflections of the Tower have been inferred and measured since 2009. Available information on this case history include geotechnical site conditions and data from a monitoring program that tracked foundation settlements, Tower tilt, groundwater levels at the Tower site, and ground inclinations over time. This presentation will discuss the ground deformation mechanisms that caused the observed movements, the degree to which the movements can be predicted, and lessons from this case history for the design of deep foundations for tall buildings in San Francisco and geologically similar regions.

Sep 8, 2021

By Osamu Taki

The development of new auger bits for soil cement column drilling equipment has made it possible to create a homogeneous mixture of soil and cement-reagent slurry. As a result, soil-cement columns are used for foundations of houses and buildings, with reliable results, as demonstrated by many field projects and laboratory tests. This paper presents and discusses construction techniques for soil-cement columns, characteristics of the soil-cement solid, quality control, bearing test results, and soil-cement foundation design procedures.

Jan 1, 1992

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees was applied to a 0.61 m (2 ft) diameter flagpole and a 0.61m (2 ft) diameter fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil was represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2012

By James J. Cahill

Contractor's working in an urban environment face a multitude of working conditions. There is no typical "Downtown" job site. From afar we just see the skyline, or up close a specific building. This, of course, does not give us a clue as to the site conditions the foundation contractor faced in doing his work. The open, downtown building site is still available on some projects, but they are becoming rare as our cities are becoming more developed. A typical site today might include any one or several of the following problems: A. Deep pit with no ramp access B. Multi-type known or unknown obstructions C. Height limitations D. Load restrictions E. Existing adjacent building founded on shallow foundation F. Existing foundations G. Existing tunnels, utilities or subways

Jan 1, 1991

By Steve Thoman

After the 1989 Loma Prieta Earthquake, the California Department of Transportation (Caltrans) initiated an overview of the Caltrans Bridge Design Specifications (BDS) and bridge seismic design practice in California. This overview is continuing under the direction of the Applied Technologies Council (ATC-32), to review and revise as necessary existing standards, performance criteria, specifications, and practices for design and construction of new bridge structures within California. The ATC-32 project began in August 1991 and is expected to be completed in 1995. Since 1990, Caltrans project-specific seismic criteria have been developed and implemented on the I-280 and I-480 projects in San Francisco. Caltrans and an independent seismic safety review panel continue to develop and implement these criteria on other projects. In 1991 and 1992, project-specific seismic criteria were used on the I-880 reconstruction project in Oakland. The seismic safety review panel considered the I-880 seismic design criteria a state-of-the-art methodology to ensure seismic safety against collapse of bridge structures subjected to a maximum credible seismic event. This paper highlights the 1992 "I-880 Reconstruction Project Seismic Design Criteria Review" report prepared by the Seismic Safety Review Panel and Caltrans Division of Structures and will compare pre-1989 BDS and AASHTO methodologies to the I-880 criteria.

Jan 1, 1996

By Charles M. Wilk

"Mass stabilization involves mixing binding agents into marginal or contaminated soil to improve the subject material’s physical and/or chemical properties. This paper concentrates on the principles of soil mixing and benefits and application to new and existing rail right-of-way. Successfully applied in Scandinavia and other European countries, the soil mixing is now being applied in right of way in the northern latitudes of the U.S. and Canada. These regions have significant areas of “peaty” soils that can complicate construction and maintenance of rail and structure foundations. Mass stabilization can be used to improve the bearing strength of these soft soils for subsequent construction of railroads, pipelines, roads, and buildings. In civil engineering, the technology is often used to improve the construction properties such as bearing strength, of a marginal soil. In environmental engineering, stabilization is remediation treatment technology that protects human health and the environment by immobilizing hazardous constituents within the treated material. . The treatment is conducted while the subject material remains in-place (insitu). Mass Stabilization is often used to accomplish both civil and environmental purposes on the same project effectively addressing marginal soil while eliminating the expense of soil removal and replacement.This paper presents the principles of mass stabilization technology, implementation in the field and recent completed railway projects.The example rail projects will present the various benefits that soil mixing provides to railway construction and maintenance. Bench-scale studies and full scale implementation as well as soil construction properties before and after mass stabilization will be discussed. The paper and presentation will include information on the advantages of mixing methods and binding agent delivery systems.INTRODUCTIONNew or existing railroad right-of-ways may cross ground with low bearing capacity. Right of way subgrade undergo deflection (strain) as loads (stress) are applied (1). The amount of strain or deflection of the subgrade caused by loading of a train is proportional to the stiffness of the subgrade materials. Some soils, such as tamped ballast, are very stiff and resist loads well. Other soils such as soft clay, peat, or loose sand have low stiffness and undergo substantial movement under loads. It is very desirable to have the stiffest possible material in a track subgrade. Stiff subgrade material limits deflection under load, reducing track roughness and occurrence of track defects. Mass stabilization is a geotechnical method that can be used to improve the bearing capacity or stiffness of soil in these right-of-way. Mass stabilization involves mixing binding agents into soil subject to treatment while the soil remains in-place or insitu. Variations in the design or areas subject to treatment can be used to address transmission of vibration to adjacent structures."

Jan 1, 2017

By Sylvia S. Eskander, Sherif S. AbdelSalam, Mona B. Anwar

Expanded Polystyrene (EPS) geofoam has long been used in numerous geotechnical applications due to its lightweight and durability. Among these applications is the use of EPS as an alternative fill material to conventional roadway soil embankments. This study investigates the benefits of using EPS roadway embankments to reduce the induced stresses and strains on the underlying peat and soft clay. Firstly, mechanical and interface properties of the EPS were acquired from a companion study that also considered the cyclic loading and creep effects. In order to determine the actual stress-strain distribution within the EPS blocks, a physical prototype was developed in this study with overall dimensions of 1.2 x 1.0 x 0.5 m, with a density of 35 kg/m3. The prototype EPS blocks were subjected to cyclic loading with intensities ranging from 10 to 50 kN. Then, a numerical model was developed to simulate the behavior of EPS roadway embankments. The numerical model outcomes were verified against the prototype measurements. A parametric design study was also conducted to develop a correlation between EPS embankment height and the stress-strain that occur in the underlying strata. Results showed that EPS embankments could reduce stress and settlement in the underlying soil by about 40% and 54%, respectively. EPS APPLICATIONS AND BACKGROUND Expanded Polystyrene (EPS) geofoam blocks have been effectively used during the past several decades in numerous geotechnical applications. EPS static and dynamic properties as well as interface behavior were extensively characterized in various published studies such as that conducted by Horvath, 1994; Stark et al., 2004; Zarnani and Bathurst, 2008; Trandafir et al., 2010; Athanasopoulos et al., 2012; AbdelSalam and Azzam, 2016; and others. However, to be able to use locally produced EPS blocks, its physical and mechanical properties must be thoroughly determined. The lightweight and compressible material of EPS geofoam makes it suitable both as a backfill and for absorbing pressure in both the vertical and horizontal directions. Kim et al. (2010) adopted EPS as an alternative for soil backfill around buried pipes; their model showed a reduction in the vertical stress acting on the pipes by up to 36%. Oshati et al. (2012) presented a case study of a field-instrumented box culvert with EPS blocks on top, which reduced vertical stress by 58%. Meguid et al. (2017) used an EPS inclusion to surround culverts and achieved up to 72% stress reduction, depending on the EPS density and the culvert depth to width ratio. AbdelSalam et al. (2017) used a relatively thin EPS inclusion behind flexible cantilever retaining walls, verifying that the lateral pressure can be significantly reduced by 25%; they also developed a design chart for this application. Moreover, AbdelSalam et al. (2019) investigated the use of EPS as a lightweight alternative for soil backfill above shallow tunnels. It was found that EPS had created a differential movement between the wedge located above the tunnel and the neighboring soils, which accordingly reduced the vertical stress acting on the tunnel by 85%, due to the use of lightweight EPS material and positive soil arching.

Jan 1, 2019

By Krishnendu Mandal

"For a multi-story building project in Kolkata, a pile load testing program was conducted to minimize pile performance uncertainty resulting from variable subsurface conditions and to verify the pile load vs. settlement response. The program consisted of performing five (5) instrumented load tests on augured cast-in-place (ACIP) pre-production test piles. Vibrating-wire strain gages and extensometers were installed in the test piles at strategic locations to enable measurements of the load vs. deformation behavior of the test piles. This paper presents a description of site subsurface conditions, test pile installation, instrumentation setup for a maintained load test (MLT), static compression pile load test results, and pile instrumentation result interpretation. Average mobilized unit shaft resistance values are calculated.2.0 INTRODUCTIONThe project site is located in Kolkata, near river Ganges, and the proposed development plans consist of constructing six (6)25-story (G+25) towers; see Fig. 1 and Fig. 2 below for approximate site location and proposed development layout, respectively. The buildings were designed to be supported on ACIP piles. A field load test program was implemented to verify sub-surface conditions and pile design. The test program consisted of installing Five (5) instrumented test piles numbered LP1A and B through LP6A and B, and performing static compression load tests on these piles. The piles were instrumented with vibrating-wire strain gauges and extensometers, so that the pile shaft resistance distribution along pile length and the pile toe resistance could be interpreted using direct instrumentation measurements."

Jan 1, 2015

By Nagarajan. D, Raja Rajan. K, Vijayakumar. T

Major bridges crossing mighty rivers must be constructed in flowing water. Constructing the sub-structure in water has been a challenging job for contractor. Special construction techniques with marine fleets to be adopted for waterfront construction. Enabling works like temporary piling platform and cofferdam used for pile and pile cap construction. Apart from this, enabling works like load out jetty to transport the materials from land to water; temporary walkway for access of workman to work location; temporary access bridge for construction vehicles movement; temporary liners for tower crane foundation; Concrete block to act as dead man anchor for barge movements were all required by the contractor for smooth functioning of site as per construction schedule. Investment in enabling works by contractor plays a significant role on profit margin of the project and of course with utmost safety. Design of enabling works for waterfront structures involves hydrological data like afflux, bathymetry survey, current force, scour depth and wave force to be taken cautiously for safe and economic design. Type of foundation and pile/well cap top level corresponding to water levels shall influence the construction scheme. Usage of geotechnical software like Wallap and Plaxis required for enabling work design to enhance the safety of the structure. Bathymetry and soil condition play a critical role in design and construction of enabling works. Water Discharge quantity in river along with water levels like low water level, high flood level, seasonal fluctuation of water levels has a great impact on design of enabling works. Establishing enabling works for waterfront construction near to an existing bridge is an additional challenge for the contractor. Along with design, constructing the enabling works in water requires special construction methodology and sequence of work. This paper shall provide insights on overview of design and construction of enabling works for waterfront construction.

Nov 1, 2022

By Eric S. Lindquist

Two microtunnel access shafts were constructed using the Cutter Soil Mixing (CSM) method in the San Joaquin Delta region of California, east of San Francisco. Unlike conventional slurry walls and diaphragm walls that utilize concrete, soil mixing relies on blending the soils in situ with a cement slurry to create a soil-cement wall. Cutter Soil Mixing technology utilizes two sets of vertically mounted cutting wheels rotating about a horizontal axis to produce rectangular panels of treated soil. Overlapping of the soil mixed panels enabled the construction of two circular shafts. CSM panels were constructed to a depth of 29 m (95 ft) for the microtunnel jacking shaft and to a depth of 19 m (63 ft) for the microtunnel receiving shaft. The site presented several challenges, including the high depth of treatment, the variable nature of the alluvial soils, and the high water table. This paper describes the CSM technique and presents the design, construction, quality control measures and advantages of using this method for this project.

Jan 1, 2010

By Karl A. Higgins

In August 2004, the long-awaited National Harbor project in the DC metro area sprang to life with the design of Gaylord National Resort and Convention Center. When the project was in its final stages of construction in 2007, it was noted as largest building development of the east Coast and the 4th largest Building project in the U.S. The final construction costs were above $900M and it served as the catalyst for the overall National Harbor development which added another $1B in construction costs over the next few years. The Gaylord Hotel is supported by approximately 150,000 linear-feet of driven precast concrete piling, one of a handful of major DC area projects in the early 2000s that were supported by this pile type. The project overall was a success, but the fast-paced construction schedule created significant challenges to the designers and contractors. Piling installation was the first major building construction task, and it did not start out well. While the test piles were installed without damage, when production pile driving began in the summer of 2005, pile head and body breakage soon became evident. Typical of most highprofile projects, there are many stakeholders involved and an equal number of opinions on why the piles were breaking. The financial and contractual implications of starting the project off awkwardly were evident to all. The pile driving criteria was scrutinized by the contractor, and the engineer’s had reservations about the size and type of the hammers used for pile driving. Ultimately, it was proven the leading cause of pile breakage was neither the pile driving criteria nor equipment, rather the pile materials themselves. The author of this paper is also the Geotechnical Engineer of Record for Gaylord National and many of the adjacent National Harbor buildings including the recently completed MGM casino. About 100 piles were damaged during Gaylord’s construction some requiring multiple piles for replacements. Over the past decade or so, rumors on the causes of the pile breakage have spread in the market, with some alleging this pile type is not compatible with the geologic setting. I have purposely avoided writing this case-study due to the controversy surrounding the subject, but now some 15 years later it seems appropriate to do so considering DFI’s annual conference location. This will be a fact-based assessment of pile breakage at Gaylord and will also include a comparison to the neighboring buildings where far fewer driven piles were damaged, once a more appropriate concrete mix design was required. The pre-cast supplier is no longer in business.

By Jonathan J. Dewsbury

It is argued that approximate computer based methods are only suited to modelling conventional piled rafts, for pile enhanced rafts where the interactions will be non linear three dimensional finite element analysis is required. However current 3D finite element analysis often relies on symmetry to reduce computational cost and there are concerns over the dependency of the results on the user. Therefore a new strategy within the finite element framework has been proposed. The main advantage of this strategy is that each stage of the model can be checked for consistency. There is also the added benefit that non symmetrical models can easily be constructed by tying the validated components together without dramatic increases in computational time. The proposed strategy compared well to the published results of a hypothetical example of a piled raft previously analysed with numerous methods by Poulos et al. (1997).

Jan 1, 2010

By Charbel Khoury, Kwabena Ofori-Awuah, Kofi B. Acheampong

"Following heavy rains in spring of 2014, Prince George’s County officials issued a mandatory evacuation for homes in the Piscataway Hills subdivision of Fort Washington, Maryland where a landslide along a 1700-foot hillside destabilized homes, collapsed the single access road, and resulted in water and sewer mains break. Forensic investigations, including geologic assessments, test borings and in-situ Cone Penetrometer and Dilatometer soundings, were performed to evaluate subsurface conditions and provide stabilization options for the roadway and slopes. Post-failure ground movements were monitored using inclinometers. Critical failure planes were identified within the underlying 30-foot thick Marlboro Clay formation, a known geologic hazard with historic occurrences of landslides and slope failures.This paper discusses the remedial design for stabilizing the landslide and 60-foot hillside slope failure, and protecting the roadway. Amongst several feasible options, driven piles were selected in consultation with the County and retained contractor based on cost, environmental impacts and site constraints. Constraints included private ownership of hillside slope, upslope buildings safety; deep-seated failure, relocation of underground water and sewer mains, and accelerated construction schedule.Pile design included global slope stability analyses and lateral pile analyses using several loading configurations to optimize pile geometry and spacing, and determine a value-engineered design satisfying both serviceability and strength limit states to achieve long-term stability with factor of safety of 1.3. Soils within the active landslide plane were assumed to provide no resistance, while soils below the failure plane provided lateral resistance. This stabilization scheme, which extended along the 1700-foot roadway section and toe of hillside slope area, consisted of 410 steel HP16x141 piles in two to three rows driven to depths between 60 and 70 feet below the Marlboro Clay stratum at 5 to 7-foot spacing."

Jan 1, 2017

By Mark H. Balfe

Over the last decade, Fenway Park has undergone annual improvements to modernize the facility for players and fans. These renovations include the Monster Seats, the Right Field Roof expansion, a new pavilion behind home plate, expansion of the Red Sox clubhouse, additional roof seating, and concourse improvements. Retrofitting the historic ballpark to bring it up to current standards required installation of foundations to support the new structural loads for each of the alteration projects. This required evaluation of existing conditions, and in many cases augmentation of the foundations at existing columns to accommodate the structural changes to the park. New foundations, generally consisting of drilled-in micropiles, were installed in numerous configurations and conditions. Since 2003, a total of 215 drilled-in micropiles have been installed to augment various columns around the park. The micropiles range in capacity between 40 and 70 tons and are installed through Fill and Organic Soils and embedded into the dense Glaciofluvial Sand and Gravel layer. Issues and learning related to the foundation augmentation include schedule constraints (work is typically conducted during the off-season and schedule is very aggressive), encountering old/abandoned utilities or foundations, ventilation of equipment, and management of spoils during micropile installation.

Jan 1, 2011

By Bengt H. Fetlenius

The "Pile Prediction Event" at the ASCE GeoInstitute's Deep Foundation Conference in February 2002 involved prediction of drivability and capacity of three 14m long, 324mm diameter, closed-toe pipe piles driven into loose to compact fine sand to slightly silty sand. Predictors were provided the results of two soil borings and three cone penetrometer tests, as well as type and model of hammer to be used for the pile driving. A total of 33 persons submitted predictions. As to penetration resistance distribution, many predictions were far below actually observed values. As to capacity in compression, the predicted values ranged from 270KN through 2,340KN with a mean of 1,070KN. As to capacity in tension, the predicted values ranged from 100KN through 1,650KN. The maximum load applied to the compression pile in the static loading test was 1,25OKN, at which no more reaction load was available. The reaction system for the tension test failed early in the test. CAPWAP analysis on End-of-Driving blows showed capacities at the end of the driving for the push and pull piles of 670KN, and 710KN, respectively. No restrike tests were made. Additional CPT soundings indicate that the pile driving had densified the soil. Static analysis and calculations from the CPT indicated that capacities ranged from 1,000KN through 2,000KN. The paper presents the data and discusses the various methods of determining pile capacity and addresses influence of set-up Lessons useful for future similar events are indicated.

Jan 1, 2004

By Justin Simmons, Michael Arnold, Bob Faulhaber

"In order to remodel an existing beach resort on the Gulf of Mexico, an existing three story structure, founded on stepped tapered piles, was to be replaced by a ten-story building with service rooms on a daylight basement level, conference rooms on the next levels and up-scale hotel rooms on the upper levels. The new building was founded on augered-cast-in-place (ACIP) piles. The pile caps and the basement required excavations between nine and fifteen feet (three to five meters) below ground surface.BAUER Foundations Corp. (BFC) successfully used Cutter Soil Mixing (CSM) to install the support of excavation walls. This technique allowed for the adjustment of the wall alignment during execution in order to avoid existing and new piles and other underground obstructions. Nearly 1600 – 16-inch (400 mm diameter) ACIP piles were installed to an average depth of 71.5 feet (22m) below ground surface (BGS) by BFC to support the new hotel structure. Initial grout overages in piles were excessively high and ground stability issues were encountered in some pile locations. By identifying specific areas of concern BFC was able to modify the approach to ACIP installation, effectively mitigating the ongoing risks and successfully completed the project.PROJECTMarriott Hotels began the $300 million renovation and upgrade of their Marco Island Marriott Beach Club Hotel in Marco Island, FL to JW Marriott status in May 2015. The renovation included the demolition of a portion of their existing hotel tower, and the construction of a new 10-story hotel tower consisting of 94 new guest rooms and a 10,000 SF (900 m2) ballroom, among other amenities. As is typical with hotel construction, time was of the essence. The schedule was the driving factor of this project as the owner had already booked events in their new ballroom starting in January of 2017.BFC provided the client with a deep foundation package that included the installation of 1562 Augered Cast-In-Place (ACIP) piles supporting the new tower, and the design and construction of approximately 36,500 SF (3,400 m2) of soil-mixed retaining wall for support of excavation (SoE)."

Jan 1, 2017

By SungJe Chi

Intrinsic remediation is the effect of natural attenuation mechanisms - dilution, dispersion, sorption/precipitation and biodegradation - reducing contaminant concentrations in ground water to specified levels at predetermined compliance points in the aquifer. Current monitoring and modeling for post closure was used to assess the current and long-term potential of intrinsic remediation of contaminated seepage originating from a large reactive (sulfidic) tailings impoundment near Questa, New Mexico. It is concluded that the natural attenuation mechanisms of precipitation within the tailings (as a result of buffering) and dilution/dispersion within the aquifer are currently active and likely sufficient to reduce contaminant concentrations to below state standards in the long-term. Other natural attenuation mechanisms such as sorption and biodegradation within the receiving aquife4s) were not assessed here, but are likely further reducing contaminant concentrations. Active interception and recovery of the seepage water is being maintained until monitoring demonstrates that intrinsic remediation has successfully achieved the level of water quality control required.

Jan 1, 2017