Search Documents

By Inc. Pile Dynamics, Daniel S. Belardo, Marcus Galvan, George Piscsalko

Soil nails are often utilized as a temporary or permanent earth retention technique for slope stabilization and for excavation retention for existing or new structures. Soils nails are generally advantageous as installation is relatively rapid and they can be installed beneath existing structures and where site access for equipment is limited. Due to the typically small cross-section of these elements, the inability to inspect the holes prior to grouting/concreting, and the various installation techniques utilized, quality control for assessing the integrity along the entire length is limited. Currently, quality assurance is conducted by load testing to verify the pull out capacity after installation. The load testing is typically done on a small percentage of the total number of soil nails. This paper will provide the results of a demonstration where the new Non-Destructive Test (NDT) method Thermal Integrity Profiling (TIP) was used to access the integrity of several soil nails along their entire lengths. This TIP method has been successfully used for several years to assess the integrity in drilled shafts and ACIP piles. The TIP method assesses the integrity across the entire cross-section and can identify regions where bulges, necks, and insufficient grout/concrete are present. TIP testing can also help assure that the contractor's installation methods are adequate and consistent for the intended design. For the project presented, instrumented Thermal Wire were affixed to the centered tension bars prior to placement in the excavated shafts. Temperature measurements were recorded from the hydration energy generated after grout/concrete placement, capturing the entire heating cycle. Manufactured defects were installed on the center bar at multiple locations. The results and conclusion will be discussed as well as recommendations for future use.

Jan 1, 2017

By David Pierce

The Port of Seattle, one of the largest on the west coast of North America, made a strong statement regarding their support for reusing existing structures when a decision was made to rehabilitate Pier 69, on Seattle's downtown waterfront, for their new headquarters. Because of its age and location, the pier provided an unusual challenge to the Port and its consultants. The Port hired Peratrovich, Nottingham, and Drage Inc. to design the seismic strengthening of the pier itself. To remedy the lack of seismic resistance in the 70-year-old pier, PN&D designed a new steel-pipe-pile supported concrete apron next to it. The structure relied on a development by PN&D, the "spin-fin pile", to achieve the tension capacities required of the batter piles. The construction of this apron was completed in October of 1991. Another team of consultants performed the superstructure renovation design, which is now under construction.

Jan 1, 1992

By Lynn Crayne

We used Glyoxal as the hardener, at a final concentration of 10% by volume and therefore 20% by volume in the A-Component. They worked pretty well what we did was we shaved the joints on each of the pipes when we assembled them so they wouldn't rip the packers and then we greased the packers very well going in. We had to replace some but we have any getting stuck or didn't lose any pipes.

Feb 10, 2003

By Mohsen Elsayed, Amr Sallam, Ahmad Mohamed, Xuebing Zheng, Mohamed Alrowaimi

The foundation is an essential component of the wind turbine that ensures continued operation under stable and safe conditions. Both shallow and deep foundations are utilized to support wind turbines including gravity spread foundation, anchor foundation, pier or drilled shaft foundation and pile and pile cap foundations. Conventional methods were typically utilized to design the wind turbine foundations. With the advances in numerical modeling in the geotechnical field, foundation designers may utilize numerical analysis to design wind turbine foundations. Geotechnical numerical packages allow modeling structural components and soil-structure interaction that is usually neglected in conventional methods. Furthermore, the subsoil conditions, geometries, stress-strain behavior, boundary conditions and load staging can be modeled, minimizing the assumptions and generalization. This results in better understanding of the stress strain behavior of the foundation leading to optimized foundation designs. This paper includes a brief review of current foundations used to support wind turbines with an emphasis on post tensioned single pier foundations. The current conventional foundation design methodologies and state-of-the-art foundation design utilizing numerical modeling of the single pier foundation will be discussed. Two case histories where the single pier foundation, designed using numerical modeling, were utilized to support the wind turbines will be presented. INTRODUCTION The foundation is an essential component of every wind turbine that ensures continued operation under stable and safe conditions. Turbine manufacturers provides load specifications for designers to be utilized for wind turbine foundations design. Loads include bending moments, torsional moments, lateral forces and vertical forces in both operational and extreme wind conditions. Essential specifications under seismic conditions might also be provided in seismic prone areas. Turbine manufacturers also include foundation design criteria including minimum rotational stiffness, minimum horizontal stiffness, maximum allowed inclination and maximum allowed lateral movement under both operational and extreme loads. Geotechnical explorations and evaluations are typically performed at early stages of the wind development projects. The field explorations usually include Standard Penetration Test (SPT) borings, Cone Penetration Test (CPT) Soundings, geophysical surveys, and laboratory tests to define soils stratification system and soil strength and compressibility characteristics. The most critical soil parameters for turbine foundation design are shear strength parameters (cohesion and friction), shear modulus, Poisson’s ratio, and unit weight. The depth to the groundwater table is also a crucial parameter in design. Advanced field explorations techniques such as Dilatometer Tests and Pressuremeter Tests may also be utilized. Laboratory tests for foundation design typically include index parameters, consolidation and triaxial tests.

Jan 1, 2019

By Rachael M. Fischer, Daniel J. Woeste, Terence P. Holman

"A new 50 MW biomass renewable energy power plant was planned for construction in southwestern Georgia. The original foundation design consisted of very conservatively designed H-pile groups with vertical and battered piles to carry the axial and lateral loads. The authors conducted a testing program to value-engineer the foundations with the goals of increasing the working axial pile resistance and reducing or eliminating battered piles. Seven test piles were installed and dynamically monitored with a Pile Driving Analyzer (PDA). Two lateral load tests and one tension load test were conducted. The results of our testing program allowed the project team to: (i) increase working pile resistances by factors of 1.5 to 2, reducing the total number of piles by more than 30%, (ii) eliminate the battered piles, and (iii) lessen overall project risk. Poor communication and documentation in a critical area of the site required some piles to be spliced and re-driven after additional PDA testing, establishment of new driving criteria, and consideration of longterm soil setup. This case study emphasizes the economic and risk reduction benefits of a design phase testing program, and the need for consistent communication between parties in the field.INTRODUCTIONA new 50 MW biomass renewable energy power plant (Plant) was planned and constructed in southwestern Georgia. The Plant converts clean wood-based and paper-based waste from existing forestry and pulp operations, waste timber, and maintenance operations into steam that is used by an adjacent manufacturing facility. The Plant also generates electric power with limited greenhouse or particulate emissions for use by a local utility provider.The project site (Site) is located in Dougherty County, in the Coastal Plain physiographic province of Georgia; an area of known karstic activity. Specifically, the Site is underlain at depths of 30 to 45 ft by the Ocala Formation, a light-colored fossiliferous limestone of the Eocene era. According to Watson (1981), the Ocala Formation is 125 to 200 ft thick in the vicinity of the Site and increases in thickness to the southeast. Due to differential weathering, this formation is characterized by an irregular upper surface that transitions from sandy clay/clayey sand into a dense to very dense silt and fine sand locally referred to as limestone. This subsurface stratum is most relevant to the foundation design of the Plant."

Jan 1, 2016

By Paul R. Lear

Sustainability continues to be an important aspect of remediation and infrastructure projects. Deep soil mixing (DSM), a common construction and remedial technology, can easily incorporate the following sustainability best management practices (BMPs), including Minimizing Total Energy Use and Maximizing Use of Renewable Energy; Minimizing Air Pollutants and Greenhouse Gas (GHG) Emissions and Maximizing Use of Machinery Equipped with Advanced Emission; Minimizing Water Use and Impacts to Water Resources; Beneficial Reuse of Materials/Reduction of Materials and Waste Reduction; Use of Local Labor and Supplies. This paper focuses on the sustainability of DSM treatment and provide carbon footprint calculations at least one completed DSM project which used these sustainability BMPs to demonstrate the environmental impact of the sustainability.

Sep 8, 2021

By Adam Zagorski, Rusty Lucido, Curt Scheyhing

"The current California Department of Transportation (Caltrans) practice based on AASHTO LRFD Bridge Design Specifications is to use the O’Neill and Reese method (FHWA, 1999) for calculating the side resistance and base resistance of Cast-in-Drilled-Hole (CIDH) piles / drilled shafts. In this calculation, end bearing is typically neglected for piles constructed using a wet method due to questionable reliability of end bearing resulting from soil disturbance and inadequate cleaning of the base. Pressure grouting below the tips of drilled shafts in cohesionless soils has long been used worldwide to provide reliable end bearing capacity, but for decades it was relatively unused in this country. It has been used increasingly in the United States over the last decade. Before this project tip grouting has not been utilized on or accepted by Caltrans to maximize piles end bearing capacity. This project proved that tip grouting to mobilize reliable base resistance can be successfully implemented on a full-scale bridge project requiring over 350 large diameter shafts.For the Gerald Desmond Bridge Replacement Project, Shimmick/FCC/Impregilo, JV utilized a temporary Oscillator casing to the full depth to install CIDH piles. Piles were constructed by the wet method and then pressure grouted below the pile tip. A tip grouting procedure for these large diameter shafts was developed and tested to specifically address the geology and constraints of the project. This procedure was then proven during the Load Testing of test piles during the Test Shaft construction phase of the project. Tests showed a minimum reliable base resistance of 150 ksf could be mobilized in very dense sand at a downward movement of 5% of the pile diameter for piles ranging from 4.9 to 8.2 feet in diameter. By tip grouting, the length and diameter of the piles were significantly reduced."

Jan 1, 2017

By Henry Zhang

This paper presents two case studies of large diameter driven tubular steel piles for the ongoing Woolgoolga to Ballina Pacific Highway upgrade (W2B). This project forms part of Australia’s largest regional infrastructure project and will upgrade about 155 kilometers of highway to four-lane, divided road. There are more than 170 bridges on W2B, and driven tubular steel piles are adopted on 43 bridges between Glenugie and Ballina. Driven piles terminating in soil or basalt is a big challenge faced by both designers and piling contractors due to 1) the uncertainty of expected pile unit shaft and base resistance in different soils; 2) whether plugging is formed; and 3) highly variable basalt strength and thickness near top of the rock. If these risks are not adequately managed during design or construction stages, it could lead to unexpected project delay, extra time and cost or pile toe damage in basalt. This paper describes two case studies, one for piles designed to terminate in soils and the other for piles designed to terminate in basalt. How these risks were assessed and managed during detailed design, procurement, hammer selection, pile installation and verification will be discussed in details with lessons learnt summerised in the conclusion.

Nov 1, 2022

By William B. Conway

This paper will describe the large caisson pier foundations for four of the bridges crossing the Mississippi River in the New Orleans area; and will discuss some of the unusual problems encountered during their sinking. Certain settlement phenomena experienced during their service life will also be related: The four bridges in order of their construction: The Huey P. Long Bridge, River Mile 106.1, completed in 1935 The Greater New Orleans Bridge No.1, River Mile 96.0, completed in 1958 The Hale Boggs Bridge, River Mile 121.6, completed in 1983 The Greater New Orleans Bridge No.2, River Mile 96.1, completed in 1988 Each of these bridges employed large open-dredged concrete caissons as foundations for one or more of the river piers, with the smallest being the 65ft by 102ft caissons for Piers I and II of the Huey P. Long Bridge and the largest being the 99ft by 214ft caisson for Pier II of the Greater New Orleans Bridge No.2. The Huey P. Long caissons are founded in a dense fine sand at -170 while all of the other bridge caissons are founded in hard preconsolidated clay at elevations varying from -150 to -185. The Huey P. Long Bridge is currently being widened without increasing the caisson foundations under any of the river piers; and the design reasoning that led to this decision is presented.

May 11, 2007

"This model specification includes sample text shown in normal font with commentary in italics. The commentary is intended to highlight project-specific items the specification writer should consider during development of the specification. In some sections, typical values are presented to indicate common practice, and these values may be changed to reflect projectspecific requirements. The commentary should be removed before using the specification for a project.1. SCOPEThe work consists of designing, furnishing, installing, post-tensioning and testing helical anchors used to support tension loads, and any ancillary materials (e.g., load transfer devices, etc.) according to the project plans provided and these specifications. Unless otherwise noted, the installing contractor shall provide all labor, tools, equipment, and materials necessary to accomplish the work. The parties referred to in this specification are as follows:• The Owner is the property owner.• The Owner’s representative is the individual or firm hired by the Owner to execute project tasks required for the successful design and construction of the overall project. Tasks could include construction management, design, oversight, etc.• The anchor designer is the individual or firm generally hired by the installing contractor to design the helical anchors.• Installing contractor installs and tests (if necessary) the helical anchors, and possibly other tasks associated with the project.It is important to clearly define the roles and responsibilities of every party on each project to promote good communication and reduce potential for contractual misunderstandings. Different types of contractual vehicles (design-build, value engineering, etc.) require different roles and responsibilities for the various parties, which should be considered in specification development.The Owner will provide suitable access to the construction site for the installing contractor’s personnel and equipment. Unless specifically noted otherwise in the contract documents, the Owner will remove and replace any structures, utilities, pavements, landscaping or other surficial improvements in the work area as necessary to facilitate the work. The Owner will be responsible for overall construction oversight to minimize potential for developing unsafe conditions. The work may include post-construction monitoring of anchor performance if required by the Owner or the anchor designer to confirm performance of the anchors subsequent to their installation. The work may also include installation of additional anchors if the initial installation does not meet specified capacity or performance requirements. Responsibility for providing subsurface investigation shall be addressed in the bid documents. The Owner is responsible for providing to the installing contractor all available subsurface soils, rock and groundwater information and geotechnical testing data."

Jan 1, 2016

By Marco D. Boscardin, Kenneth A. Pidgeon, Adriane G. Boscardin

"Hollow bar tiebacks can offer an economical alternative to conventional solid bar and strand tieback systems for use in temporary excavation support construction. However, the limitations associated with the installation of hollow bar tiebacks require special attention during design, construction and load testing to verify conformance with conventional performance and proof testing criteria (PTI, 2014). In particular, providing a reliable free length is complicated by the 10-foot (3-m) -long, segmental, couplingto- coupling nature of the free length sheath in the hollow bar system, and addressing the fully grouted annulus of the bond zone and the free length zone at the end of installation are key concerns. In addition, it is often more convenient to install a greater number of more closely spaced, lower capacity tiebacks with the hollow bar system, compared to conventional tiebacks. This paper examines how these issues were addressed for a project involving a 60-foot (18-m) -deep sheet pile excavation through a highway embankment and a 70-foot-deep sheet pile and soldier pile and lagging excavation through a railroad embankment, both supported by a hybrid system of hollow bar tiebacks and hollow bar soil nails. The project involved approximately 300 tiebacks and 400 soil nails.INTRODUCTIONEngineers Construction, Inc. (ECI), constructed a pair of 32-foot (9.8-m) -wide (clear span), 30-foot (9- m) -high (21 feet (6.4 m) above the stream bed), cast-in-place concrete arch culverts as a design-build project for the Vermont Agency of Transportation (VTrans) in East Ryegate, Vermont. The new culverts replaced an existing 8-foot (2.4-m) -wide by 6-foot (1.8-m) -high cast-in-place concrete culvert under US Route 5 (RTE5), and twin, 2-foot (0.6-m) -wide by 5-foot (1.5-m) -high granite block culverts under the Washington County Railroad (WACR) alignment. The culverts convey Manchester Brook eastward, through the embankments for RTE5 and the WACR, on its way to the Connecticut River. The Connecticut River is located approximately 100 feet (30 m) east of the WACR embankment. The existing structures were undersized and backed up water behind the embankments during high flow events; and often trapped debris that flowed down the brook and became clogged. The existing culverts also had cracks and openings that have resulted in the loss of ground into the culverts and the formation of sinkholes in the sides of the embankments. Moreover, the reason for the large cross-sectional dimensions of the culverts was to make them of sufficient size and openness to encourage the migration of fish up the stream to spawn. The culvert through the RTE5 embankment is 144 feet (44 m) long, and the culvert through the WACR embankment is 128 feet (39 m) long, with a 57-foot (17.4-m) -long by 32–foot (9.8- m) -wide by 17-foot (5.2-m) -deep 10 feet (3 m) deep above the stream bed) open channel section between the two culverts. A plan view of the culvert alignment is presented in Figure 1."

Jan 1, 2016

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002

By Elizabeth M. Smith

The kcICON design-build project in Kansas City, Missouri includes widening the existing roadway, improving interchanges and grade separation bridges, and replacing the Missouri River Bridge. The Missouri Department of Transportation (MoDOT) typically utilizes steel H-piles and steel pipe piles as driven pile support for bridges. After bidding the kcICON project, the cost of steel rose significantly and the design-build contractor used an innovative approach to reduce foundation costs without significantly affecting the project schedule. The kcICON team conducted a value engineering evaluation of alternative foundation types for use at four grade separation structures. The result of the value engineering evaluation was selection of precast, pre-stressed concrete (PPC) piles as the preferred foundation alternative. Terracon developed a test program to evaluate the performance, capacity, and suitability of PPC piles at the site using a PDA and CAPWAP analyses. This paper presents the value engineering design, rationale for selection of PPC piles, results of the pile test program, and findings during production pile driving. The collaborative approach to the project by MoDOT and the kcICON team, combined with testing and a site-specific design approach, resulted in substantial savings for the design-build contractor.

Jan 1, 2009

By Joel Moskowitz

In 1990, the United States General Services Administration (GSA) issued a contract for design and construction of a new federal court building in New York City. Mueser Rutledge Consulting Engineers (MRCE) served as Project Geotechnical Engineers. The project site is in the historic government district at Foley Square. It is surrounded by the New York County Courthouse to the west, an existing federal prison building and federal courthouse across Pearl Street to the south and southwest, an office structure to the north, and a residential tower to the east. The interior of the site was crossed by streets which have now been demapped. As with many urban sites, this site was previously occupied by tenement buildings or industrial structures demolished near the turn of the century. Remains of old building foundations were exposed during construction excavation. In addition, buried fuel oil tanks servicing the adjacent courthouse were removed and the usual assortment of urban utilities had to be relocated for the new building foundations. Ground surface elevations vary from about 4.5 to 6 m above the local Mean High Water Datum Plane.

Jan 1, 1996

By Lori A. Simpson, Linda H. Liang

A high-rise building, consisting of two tower structures occupying the entire site, is in construction in San Francisco. The North Tower will consist of 12 and 35 stories above a one-level basement. The South Tower will consist of 9 and 22 stories over one partially below-grade level of common space; a portion of the South Tower will have a three-level basement. The towers will be supported on mat foundations bearing on native very dense sand in the footprint of the threelevel basement and on ground improved with soil-cement mixed (SCM) panels that extend through loose sand and marsh deposits into very dense sand. Shoring systems for the basement excavations include cantilevered and tiedback soldier-beam-and-lagging systems and SCM cutoff walls. Subsurface conditions include loose fill and Dune Sand and loose and soft marsh deposits overlying very dense sand of the Colma formation. Groundwater is approximately 15 to 22 feet deep; the three-level basement extends below groundwater. The site is on Market Street in San Francisco, with SF Municipal Railway (MUNI) and Bay Area Rapid Transit (BART) tunnels running below Market Street approximately 45 and 36 feet north of the site, respectively. Both tunnels are 16.5 feet in diameter. The top of MUNI and BART tunnels are 25 feet and 63.5 feet below street grade, respectively. BART has stringent requirements regarding construction adjacent to their facilities, including disallowing adding pressure to their tunnel, lowering groundwater by more than two feet, and vibrations from construction activities. Design of the shoring and the foundations within the BART zone of influence were subject to their design requirements. The project was also subject to a peer review, as required by the San Francisco Department of Building Inspection. We used FLAC to evaluate stresses at the BART and MUNI tunnels and on the SCM panels. This paper will present the mitigations needed to address seismic hazards and BART restrictions and to provide adequate foundation support for a tall building with high seismic loads.

Jan 1, 2017

By I. D. McPherson, Dominic P. Mahoney

The Metro Sports Facility is currently under development in Christchurch, New Zealand and is a key Anchor Project in the city’s post-earth quake recovery. When completed it will be largest indoor sports and swimming pool complex in New Zealand, with a building footprint in the order of 22,000m2. The site is underlain by poor performing soils comprising interbedded layers of soft compressible silts and loose liquefiable sands to over 20m depth. The site is typical for Christchurch with a shallow groundwater table and artesian conditions. The site performed poorly during the 2010-2011 Canterbury Earthquake Sequence with extensive liquefaction, and associated ground damage. To provide a resilient and economical foundation system for this key development project, deep ground improvement comprising of a uniform grid of some 7,200 stone columns in conjunction with robust shallow foundations has been adopted. This paper discusses the geotechnical site constraints, and ground performance under earthquake loading and describes the various options considered for the development. The foundation option selected, the design considerations of the adopted stone column ground improvement, and foundation solution are described in detail, as well as, construction observations. The paper aims to provide insight into an urban large-scale ground improvement project for the engineering practitioner.

Nov 1, 2022

By J. D. Findlay

The demands on development in London in recent years has led to the increasing use of top down construction methods in which there is a requirement to place steel columns to high tolerances into large diameter bored piles with deep cut-offs. A number of different proposals for the sequence of construction are being suggested. The tolerances requires for the steel columns are becoming increasingly stringent. This review examines a number of basic construction proposals and comments on the problems and solutions used by foundation contractors to provide the required foundations.

Jan 1, 1989

By Yuji Yamashita, Kazuyoshi Kamimura, Tsuyoshi Takahashi, Naoya Matayoshi

"The CDM-LODIC method (cement deep mixing - low displacement and control) method enables ground displacement to be reduced by removing an amount of soil equivalent to that of injected cement slurry and the volume of the plunged mixing tool, which causes a certain degree of ground displacement. Since the CDM-LODIC method was developed in 1985, it has been applied to over 930 sites and the accumulated volume of stabilized soil has now reached 7.6 million cubic meters.In the CDM method, the number of blade rotations per unit depth in the ground when the mixing blades are withdrawn is considered a construction item. The blade rotation number depends on the degree of mixing between the cement slurry and the ground Some field tests were performed based on the degree of mixing between the cement slurry and the ground. In these tests, a new concept of evaluating the blade rotation number when the screw rod penetrates to a given depth without injecting cement slurry has contributed to the degree of mixing. Furthermore, a correlation exists between the coefficient of efficiency of soil removal and the cement slurry admixture rate. In this paper, we discus the data collected in those field tests and present some application examples.OUTLINE OF CDM-LODIC METHODThe injection of cement slurry may cause some ground displacement during Cement Deep Mixing (CDM). In recent years, due to an increased demand for ground improvement work in urban areas, there is increased concern that buildings near any CDM site may be adversely affected. The deep mixing method which reduces displacement due to mixing (CDM-LODIC method) enables ground displacement to be minimized by removing an amount of soil equivalent to the injected cement slurry and the volume of the mixing tool, which itself causes some ground displacement. When the construction site is near other structures, regardless of whether on or under the ground, the CDM-LODIC method can be used in order to minimize any ground displacement. There are considered to be two main causes of ground displacement as shown in Figure 1. Displacement A indicates ground displacement caused by the volume of the inserted mixing tool during the penetration stage and displacement B indicates ground displacement caused by the volume of the injected stabilizing agent. Thus, by removing soil equivalent to the volume of the inserted mixing tool and the injected stabilizing agent, ground displacement can theoretically be minimized. Figure 2 shows the amount of observed ground displacement in the cases of CDM and CDM-LODIC at an actual site. These case studies indicate that ground displacement can be reduced by removing the soil."

Jan 1, 2015

By Shahid Islam, Lucian Bogdan

There is a rapid expansion of world’s infrastructure and simultaneously existing infrastructure is aging. The maintenance of infrastructures has been of particular concern to the engineering community. Monitoring and evaluating the structures have become more significant than ever. Ground anchor is an important part of the structure where it is installed. Unfortunately there are limited testing methods available to assess the force in the pre-stressing steel. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYNA Force sensors have been developed to measure the force in the pre-stressing steel during construction and at any time during the lifetime of the structure. These sensors make use of the magneto-elastic properties of ferrous materials. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. They can be used for bare, epoxy- coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the tendon. It measures the force of the steel element at the location where it is installed and can be recorded manually, automatically, or remotely. The sensor is robust, requires no maintenance and it is expected to have a similar service life to that of the surrounding structure. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. Sensor readings provide a second measurement, in conjunction with the jack pressure gauge, of the post tensioning force during initial testing procedure for ground anchors. This paper describes its application in tie-back and tie-down anchors and force monitoring of retaining walls, bridge abutment and dams where the data were collected manually, automated and remotely. INTRODUCTION Our infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.

Jan 1, 2018

By Tony Mazzo

It has often been said by consulting engineers that foundation contractors are in the business of taking risks. One would agree that the mere fact a foundation project can be budgeted, planned, engineered and executed solely on the reliability of eight test borings made at a proposed site having an area of approximately 19,000 square feet, is a risky proposition, in and of itself. Now imagine that this site is actually one half of a city block located in an urban setting in an old, congested, historical neighborhood, surrounded by narrow city streets and historic landmark buildings. And suppose that the required depth of excavation for the construction of the new building on this site is approximately 35 feet and the natural groundwater table is at a depth below existing grade of only 25 feet. Given the difficult site conditions outlined above, one could certainly add the words "challenging" and "complicated" to the inherent word "risky" when describing the construction techniques involved to undertake a foundation project of this magnitude. This case study will discuss in detail how the excavation, sheeting, dewatering and underpinning work was accomplished as well as the problems overcome along the way.

Jan 1, 2003