Search Documents

By M. R. Madhav

The ultimate pullout capacity of single batter piles has been presented in literature in three contradictory trends. These trends are: the pullout capacity of a single batter pile increases, remain almost constant, or decrease with increasing the inclination angle of the pile. The present paper presents a theoretical study which explained these trends in terms of existing initial stress condition and the earth pressure coefficient at rest. The paper also presents a form of guideline for predicting the pullout capacity of inclined piles based on simple field and/or laboratory tests.

Jan 1, 2010

By Ronald Damen, Dion Denes

"Friction fatigue is the loss of soil-pile friction around the shaft area of the pile. It has been observed during impact driving of piles, and has been modelled to a limited degree using physical scale models. This paper proposes the use of high strain dynamic pile testing to assess and quantify friction fatigue in impact driven piles. The method is applied to two case studies: one on a project off the north-west coast of Australia and one on a South Pacific Island. On both sites calcareous sand layers are present. Pile Driving Analyzer (PDA) monitoring has been conducted during impact driving of steel piles, which allowed for assessment of shaft resistance development both with depth and with progressive driving, by use of wave equation signal matching. Lessons are drawn from the case studies to improve future observations.INTRODUCTIONFriction fatigue is the loss of soil-pile friction around the shaft area of the pile, under cyclic loading or during pile driving. The phenomenon has been frequently observed in some non-silica sands, such as pumice sands and calcareous sands and has been the subject of academic study.The occurrence of friction fatigue impacts the driving behaviour of piles and the shaft friction component of the ultimate geotechnical strength (Rd,ug). If potential friction fatigue is not recognised in the design phase of a project, required pile toe levels can be significantly underestimated. This could lead to extra cost and delays, or, if no adequate pile verification is conducted, to geotechnical failure or underperformance of piles. This is especially true in remote locations, such as Pacific islands, where calcareous material is often present.A better understanding of the phenomenon would aid both pile design and driveability assessment. This paper proposes the use of high strain dynamic pile testing to assess and quantify the effect of friction fatigue from impact driving. Two case studies are presented in which high strain dynamic testing has been conducted on driven piles in calcareous sands to illustrate the method.BACKGROUNDFriction fatigueThe geotechnical strength of piles is composed of the resistance to static loading by the base of the pile and the shear resistance between the shaft of the pile and the adjacent soil. The latter is often referred to as the shaft resistance or shaft friction.During impact pile driving, a decrease in shaft resistance is often observed. Although this phenomenon is also observed during vibratory pile installation, this paper deals predominantly with impact driving. This decrease in material strength from the tip of the pile influences the shaft resistance and may be either temporary or permanent. Temporary reduction in shaft resistance is common in cohesive soils and is thought to be caused by excess pore water pressure, which has insufficient time to dissipate. This phenomenon, commonly referred to as set up, is observed to a significantly lesser extent in non-cohesive materials such as clean sands (Rausche et al., 2004)."

Jan 1, 1900

By T. Jason Hardell

The Victory Bridge project was contracted by the New Jersey Department of Transportation. The project included the construction of two 4000-ft precast segmental concrete bridges to replace the existing Victory Bridge that was built in the 1920's. The existing bridge was a swing span bridge that was in desperate need of replacement. The project was considered high priority due to the large maintenance costs to keep the swing span operating over the busy navigational channel. In March of 2003 construction began on the first bridge and by April of 2005 all of the segments were set for the second bridge. On September 5 of 2005 the second bridge was open to traffic. The total cost of the project was $110-million. The two new bridges required the construction of 24-eight foot and 32-six foot diameter-drilled shafts with rock sockets. All of the shafts were constructed in the tidal Raritan River working from barges. What will follow is a description of the construction techniques that were used to build these drilled shafts, the anticipated and unanticipated challenges that were encountered during the project, and the lessons learned.

Jan 1, 2005

By Fathi Abdrabbo

Open caissons are used for many geotechnical engineering applications. Open caissons may be used as deep foundation elements bypassing weak soils to tip in firm deeper strata, and in rivers and maritime construction to reduce the risk of scour. Open caissons are also used for collecting sewage water through gravity sewer pipe networks or from sewer force mains. In such applications, the design and construction of open caissons require a detailed soil investigation program. In this way, the design and construction plan of an open caisson can be developed with full knowledge of the prevailing subsoil conditions. The engineering and construction techniques are key factors to achieve functional caissons. Based on close observations during construction stages, the current study presents some challenges that were encountered during the construction of two open caissons of internal diameters 20 m and 10 m (65.6 ft and 32.8 ft). This paper describes the procedure followed to alleviate the construction difficulties encountered. Site exploration program and control measures required to satisfy design and construction requirements are crucial aspects. Sinking of open caissons in dense or very dense sands is risky. Incorrect sinking of open caissons may cause extra cost, delay in construction, and harm to nearby structures. Air/water jetting near the cutting edge of an open caisson, outside slurry trench, and/or inside open trench may be used to drive an open caisson downward. Unsymmetrical work around an open caisson may lead to tilting of the caisson. If this occurs, the tilt should be immediately corrected before resuming the sinking process. Improper cleaning of fine materials on the caisson?s excavation bed, and/or inappropriate pouring of underwater concrete may result in a defective concrete seal. The paper contains a series of practical guidelines to assist those intending to use open caissons, and shares good caisson sinking practice with practitioners. Finally, the study aims to understand the difficulties encountered and to anticipate future problems.

Jan 1, 2012

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

By Graeme McWhirter

This paper discusses the Installation of a Vibwall for the Cardiff Bay Barrage Project Wales, UK, by Kvaerner Cementation Foundations. Only the second use of the technique in the UK the wall was successfully placed to a depth in excess of 20 metres, in unique and challenging conditions. The installation of the Vibwall was a technical success, but not a financial one. The use of the technique was at its "limits" and this paper recommends some of the controls essential in the carrying out of such work in the future.

Jan 1, 2000

By E. Mongilardi

The construction of large underground openings through cohesionless or weak cohesive soils and under the water table in particular, often requires a ground improvement to be done from the surface or ahead of the excavation face in tunnelling problems. To this purpose various injection procedures have been used in the past and new outstanding techniques have been developed recently, such as "jet-grouting", extending the feasibility range. The paper presents a review of basic principles and practical design criteria with particular reference to the newest trends of development. Case histories have been selected within the experience of specialist contractor Rodio Co. showing the variety of problems solved by manifold grouting procedures and layouts, in widely different soils ranging from the sandy-gravelly alluvia of Milan to the soft marine clays of Singapore.

Jan 1, 2010

By M. Tominaga

An industrial port complex was constructed on the west coast of Leyte Island The work was started in December 1981 and completed in May 1984. This port complex includes a 665 m long wharf and can accommodate vessels ranging from a 60,000 DWT ore carrier to a 4 000 DWT general cargo ship. It now handles materials for and products from a copper smelter with an annual capacity of 130,000 t and a fertilizer plant with an annual capacity of 900,000 t. The Wharf structures consist mainly of interlocked steel pipe piles, steel sheet piles and steel pipe Piles. Material handling equipment such as unloaders, shiploaders, etc. were installed on the wharf. Site survey, planning, engineering design and construction aspects of the port development are discussed in this paper with particular emphasis on the wharf structure.

Jan 1, 2010

By Raffaella Granata, Daniele Vanni

"This paper presents the drilling and grouting program performed at two abandoned landfills located into former calcarenite rock quarries in Manfredonia, Italy. Tests performed after the abandonment of the landfills detected leachate infiltration into the groundwater, which required the implementation of a remedial program. In order to seal the rock fissures and create an impervious basin at the base of the two landfills, sub-horizontal boreholes were drilled and grouted into the rock under the waste deposits. At the same time, sub-vertical boreholes were drilled and grouted along the perimeter, to laterally confine the landfills. Finally, the landfills were properly capped with an HDPE membrane, geogrid, geotextile and topsoil. The methodology implemented to create a watertight barrier under the two landfills was innovative and cost-effective. Moreover, the drilling and grouting minimized the environmental impact of the remedial work, since the waste remained in their original location and were not affected by the remedial process.IntroductionThe two landfills, “Pariti-1 RSU” and “Conte di Troia”, are located approximately 6 km (4 miles) southwest of Manfredonia, a small town close to Foggia, Italy (Fig. 1). These landfills are located into two rock quarries, formerly used for the extraction of calcarenite (i.e., a weak calcareous sandstone, in tuff facies), and were abandoned in the early 90s. The two landfills cover a total area of about 45,000 m2 (11.2 acres), and mainly include urban solid waste with a depth of up to 25 m (82 ft). The main characteristics of the two waste landfills are listed in Table 1."

Jan 1, 2016

By Kouichi Tomisawa

Two bridges were constructed for extension work of Central Hokkaido Connection Road in 2005 at two different sites. Pile group foundations were employed for the foundations of abutments of the two bridges. In order to assess the performance of the constructed piles in the sites and to obtain design parameters for design in future, static alternating cyclic horizontal load test was carried out on one of the open-ended steel pipe piles constructed at each site. The ground at one site was characterised as a thick deposit of volcanic soils, and the ground at the other site was characterised as a very soft peat layer near the surface. In this paper the results of static alternating cyclic horizontal load tests on the piles at the two sites are presented and discussed in detail.

Jan 1, 2006

By W. Lum

In the U.S., flexible metal pipe culverts are designed by ring compression theory because the pipes are capable of deflecting and deriving side support from surrounding ground. For economy, tunnel liners are often designed as flexible structures that depend on the lateral pressure of the surrounding ground to maintain stability. In this paper, simple formulas are presented to determine the maximum deflection a concrete tunnel liner may assume and the ring compressive strength of the deflected liner. A tunnel can then be constructed to work within these limits. Similar techniques may be used to design concrete pipes.

Jan 1, 2010

By Harpal Parmar

This paper evaluates dynamic methods of pile capacity prediction by comparing their results to static load test results. Dynamic and static pile load test data were assembled from four southeastern states of the U.S. End-of-drive and restrike capacities were evaluated using the Pile Driving Analyzer (PDA) and by wave equation (WEAP) analyses. These were compared to static (Davisson criterion) loads. The best comparison was obtained for restrike PDA results; restrike wave equation analyses values also compared well. The end-of-drive results for both methods-showed relatively poor comparisons. The PDA was recognized as an important tool to measure energy transferred to the pile; this transferred energy was recognized as an uncertainty when conducting wave equation analyses. A statistical analysis showed restrike capacity results to be associated with higher precision and accuracy as compared to end-of-drive methods. The authors believe that restrike dynamic testing is essential to establish long term static soil strength and that it will lead to accurate and cost-effective design of piles.

Jan 1, 1996

By S. Merjan

Three papers were presented for discussion at the conference: 1) Instrumented driven steel tube piles at Canary Wharf; author: A. R. Gaba, United Kingdom. The author described the Canary Wharf development in the London Docklands, and in particular, the decision to build over the water by driving open-ended steel piles 25m in length into the sands below the soft estuarine deposits. The tubes were then filled with concrete above the sand plug (usually 17m below pile head). Three trial piles were instrumented with: a) resistance strain guages on the inside of the tubes; b) vibrating wire guages on the re­inforcement of the concrete. The trial piles showed elastic behaviour in five cycles of lateral loading, while the verticle load tests showed a definite bi-linear load-settlement behaviour. The initial stiff portion was a result of frictional staff resistance, both inside and outside the tube, with the soil at the base contributing at higher settlements. Loads were taken to three times working load, with no imminent signs of failure.

Jan 1, 1991

By Jørn Thomsen, Christoffer Brodbaek

"As governments increasingly accord high priority to sustainable energy, policymakers are finding that wind energy has a long track record as a proven alternative to conventional energy supply.Over the past two decades, wind turbine projects have been constructed offshore because of more stable offshore wind conditions and because there is more available space for large wind farms out in the open sea. Vindeby Wind Farm in southern Denmark was constructed in 1991. As the world’s first offshore wind farm, it provided valuable information and experience for researchers and designers that have led to new technologies and design improvements, a trend that will continue as more offshore wind farms are constructed. Today, the world’s capacity of the installed offshore wind turbines exceeds 1,000 MW. Most of these are installed in Northern Europe where there was early political support and favorable conditions, such as strong winds and relatively shallow waters. Offshore wind projects are now under development around the globe, including continental Europe, the U.K. and North America. ‘The largest offshore wind farm today is Denmark’s Nysted Offshore Wind Farm, which has a total capacity of approximately 480,000 MWh, equivalent to the yearly consumption of 120,000 households. It is five to six miles offshore in the Baltic Sea in the southern part of Denmark.The owner is a joint venture between DONG Energy of Denmark and E.ON Sweden. Bonus Energy (now Siemens) supplied the wind turbines, and P. Aarsleff A/S and subcontractors supplied the foundations. The contractor’s consultant, COWI A/S of Denmark, developed and designed the turbine foundations. With a total capacity of 165.6 MW, the project consists of 72 Bonus 2.3 MW turbines in water depths up to 33 ft. The turbines have a hub height of 226 ft, and the turbine blade diameter is 270 ft. The rotor and nacelle (the structure that houses the generator, gearbox and other equipment) weigh approximately 150 tons, and the weight of the steel tower is approximately 130 tons. The wind farm site is located in a relatively protected area of the Baltic Sea, but during the winter months, the water often freezes and the foundations needed to be constructed to resist ice forces. The founding soils at the site are overconsolidated clay tills with boulders and with a thin layer of softer surface sediments. Pockets of up to 30 ft of soft sediments were encountered, which required special foundation preparations."

Jan 1, 2009

By Zhang Yaonian

This paper describes full-scale tests on ten large bored piles with grouted end conducted for three projects in the urban area of Fuzhou city. Test program included site investigation, pile installation and end grouting. The piles were instrumented with strain gages and load cells to determine load distribution in the piles. Test results showed that end grouting improves load-settlement performance of bored pile. End grouting significantly increases the shaft resistance near the pile end. The better the end condition, the greater the shaft resistance. The average shaft resistance of the bored piles with grouted end is much higher than that of piles without grouting.

Jan 1, 2004

By Peter Faust

The foundations for the new South Viaduct Bridge in San Francisco were extremely challenging due to the requirement for very large and deep piles installed adjacent to historic structures. Drilled shafts up to 12? foot in diameter were constructed to a maximum depth of 200? feet in alluvial soils and Franciscan Bedrock using an oscillator system for the installation of the permanent steel casing. This paper provides an overview of the construction techniques, the equipment, and the challenges associated with constructing 12? foot diameter shafts on this very complex project in one of the nation?s nicest landscape setting.

Jan 1, 2011

By W. Y. Xu

In comparison with shallow foundation, usually higher bearing capacity, smaller average settlement and better stability are the engineering characteristics of pile foundation. Besides, a smaller differential settlement and a lower settlement rate which will converge quickly are more important characteristics. The superstructure of the building with pile foundation may not meet with significant differential settlement. In this paper, settlement records and other data of different kinds of buildings are chosen to illustrate the characteristics of pile foundation. Moreover, some technical problems in connection with foundation engineering solved in consideration of the above mentioned characteristics of pile foundation are also introduced.

Jan 1, 2010

By Steve Davidow, Scott Tunison

As the demand for electric power grows and generation facilities are constructed in more remote areas, the industry faces an increasing number of foundation construction challenges. The importance of quality geotechnical information prior to construction is accentuated by the linear nature of the projects and the potential for drastic changes from one end to the other, but is often difficult or unfeasible to obtain. Alignments are crossing remote, rugged and/or environmentally protected terrain, and completing a comprehensive geotechnical program is made challenging from an access or economic standpoint, or both. In these situations, the industry needs a flexible foundation alternative. This paper will present micropiles as that alternative and demonstrate how the implementation of micropile foundations mitigated these challenges on the Koolau-Wailupe 46 kV Circuits in Oahu, Hawaii, which involved rugged, steep slopes and helicopter construction methods. It will detail the selection of micropiles over other foundation options, micropile and steel pile cap design methodologies, foundation construction, and quality control. Special attention will be given to the unique geology in the area, and why precise identification of saprolite and basalt layers was integral to the successful performance of the foundations. The intention is to communicate the benefits of a flexible solution based on continuous collaboration between design and construction.

By Morgan L. Race, Matthew R. Glisson

"Most driven pile projects have plumbness limits from 0.25 in/ft (21 mm/m) to 0.5 in/ft (42 mm/m) to control bending stresses. For two projects, the project teams performed static load testing to evaluate performance of piles with sweep. One project, located in Grand Forks, North Dakota, used 9.625-inch (244-mm) diameter piles with a wall thickness of 0.395 inch (10 mm) and lengths ranging from about 130 to 160 feet (40 to 49 m). Measured pile sweep (lateral offset distance of the pile toe from the pile top) was between 12 and 17 inches (305 to 432 mm). Static load testing indicated that the piles could support the design load with axial deflection of less than 1 inch (25 mm) but only provided about 80 to 90 percent of the ultimate resistance at axial deflections of about 1.9 to 1.7 inches (49 to 43 mm), respectively. The other project, located in Shakopee, Minnesota, used 9.625-inch (244-mm) diameter pile but with a wall thickness of 0.352 inch (9 mm) and lengths around 50 to 90 feet (15 to 27 m). The measured sweep varied between about 20 and 63 inches (508 and 1,600 mm) for 9 of 214 piles driven at the site. Load testing indicated that these piles could provide the required design resistance with less than 0.3 inch (8 mm) of axial deflection and support the required ultimate resistance with about 0.5 to 0.6 inch (13 to 15 mm) to of axial deflection.INTRODUCTIONAnyone who has observed a significant number of piles has seen that, inevitably, the pile is not perfectly straight after driving. In spite of the best efforts of contractors, there are a whole host of reasons for piles to end up out-of-plumb or to have a curve, sometimes referred to as pile sweep. Most project specifications set limits for plumbness typically between 0.25 in/ft (21mm/m) and 0.5 in/ft (42mm/m) (USACE, 1991; PDCA, 2007; MnDOT, 2016; MoDOT, 2016). Closed-end pipe piles, including monotube or tapertube, are the only pile type that allow actual measurement of the final alignment of the pile.As Nadeem, et al. (2015) note, buckling failure of long, slender piles is the predominant mode of pile failure in soft soils. Pile sweep is just one source of buckling failure in long, slender piles. The nonlinear buckling analysis showed that increasing slenderness ratio and/or increasing degree of curvature decreases the loadcarrying capacity of a driven pile. Nadeem, et al. (2015) considered solid, steel pile with lengths from 24 to 66 feet (7.5 to 20 m), diameters from 9.75 to 26 inches (244 to 660 mm), initial bends from 2 to 6 inches (50 to 150 mm), and half- and quarter-sine shapes."

Jan 1, 2017

By E. E. De Beer

This paper describes a method for the determination of the settlement of an individual H-bearing pile, based on the results of CPT-tests. As implied by the nature of the problem, no analysis performed on one pile can be regarded as generally valid for a whole piling foundation project because, even on one site, the pile behaviour varies from one pile to another. Consequently, no precise mathematical analysis has been established; the proposed procedure represents a simple model for the determination of the probable settlement behaviour of an H-pile under a compressive load. Prior to the settlement computations, the rupture load and the resistance distribution along the pile have to be determined. Since the method for the determination of the H-pile bearing capacity from the results of CPT tests has been described elsewhere (de Beer, 1971, 72; de Beer et al., 1982; Arbed, 1985), no details will be given in this paper. The proposed method is valid for both uniform and non-uniform H-piles. The computed results have been satisfactorely compared to the static loading tests performed on different types of piles in clayey and sandy soils during an ECSC research program on H-bearing piles (1983-1987).

Jan 1, 1987