Search Documents

By Shawna Munn, Carol Dounitch, Erika Acton

The EQ Bank Tower, a 24-storey office tower with 4 levels of underground parking, is currently under construction at 25 Ontario Street in the downtown core of Toronto, Canada. The tower geometry required an 18 m (60 ft) deep excavation inside an existing 3-storey 100-year-old façade, to be retained in place throughout construction. This presented a variety of design challenges that required several innovations and a customized monitoring program. In this paper, we will discuss two major challenges, and highlight the innovative and adaptable solutions carried out using performance-based design leveraging the observational method. The first was installation of a shoring system in a 500 mm (20 in) gap between the historical façade and a live gas main. The second involved excavating 10 m (33 ft) into expansive shale bedrock adjacent to a sensitive neighbouring building.

Oct 1, 2022

By Dempsey S. Thieman

Innovative marine bulkhead design and construction techniques were used in the fast-track design and construction of a high-capacity, deep-water dock in the highly seismic region of Alaska?s Aleutian Islands. The geotechnical investigation and design through construction phases were completed in just eight months. The adaptable OPEN CELL® design, readily available standard flat sheet pile and an experienced contractor were integral to the successful completion of the project. The cost of the structure was determined to be approximately 50 percent of a comparable pile-supported platform dock structure, allowed higher load capacity, rapid construction, less maintenance, and provided substantially more uplands. This paper details the design and construction of this unique and challenging project. The OPEN CELL structure is a vertical flexible membrane system that offers significant advantages over other structure types: ? Its flexible membrane structure is not dependent on toe embedment for stability. ? Poor soil conditions, shallow bedrock, high seismic loads, deep water, scour, etc., can be accommodated due to its adaptable design. ? It has a very high load capacity?capable of several thousand pounds per square foot. ? Allows buried utilities which results in lower cost and reduces freezing conditions ? The sheet pile tail walls can be extended to provide increased global stability if needed. ? Standard sheet pile and connectors with traditional installation techniques allow accelerated construction schedules.

Jan 1, 2008

By Rajesh Minda

160 numbers of double bulb underreamed piles were constructed based on the safe loads specified in IS code at Tripura. The pile load tests yielded a much lower capacity. A detailed investigation work was carried out to find out the reasons for anomaly. The work included soil exploration followed by extraction of two piles bearing numbers 72 and 151. It was seen that the bulbs were not formed as per specification. Some comments on IS Code have been made at the end.

Jan 1, 1996

By P. J. Nicholson

The methods of reinforcement to be discussed in this paper are all insitu methods, ones that can be used on the soil structure as it exists in the ground, and do not rely on excavation and replacement of the soil. Current practice in the United States, as well as new ideas and methods, will be discussed as they relate to slope stability, retaining walls, and to other uses such as control of mine or cavity related subsidence and to liquefaction control under existing structures. The method is based on the concept of "nailing" or reinforcing the soil in place, and thereby causing a mass of soil to act as a coherent unit. When performed properly, a true gravity structure can be constructed, one that will remain intact under both horizontal and vertical loadings and that will also resist vibrational and seismic loadings.

Jan 1, 2010

By Jim Bruce

This paper presents details of a slope stabilization scheme built in late 2003 at a 16m-high railway embankment in southern Ontario, Canada. The owner, faced with continuing maintenance and safety issues arising from numerous nuisance slides, and residential neighbors in close proximity to the slope, sought new proposals to replace a previous recommendation to cut down all trees and undertake a deep soil nailing scheme. A non-reticulated micropile array with surface cap beam was proposed and built on the south side of the embankment with no tree removal required. A detailed FLAC analysis was completed, using multiple iterations to arrive at the eventual, optimized micropile depth and spacing. Analysis predicted an 18% increase in the factor of safety. Short term inclinometer monitoring and performance evaluations in the months since construction so far corroborate the prediction.

Jan 1, 2004

By Martin van Staveren

In today's rapid changing construction world, the business pressures on piling and deep foundations reach sky-high levels. Ever increasing complexity of construction projects do severely contribute to these business pressures. Projects are often constructed in densely populated areas and located close to vulnerable buildings and infrastructure. The inherent uncertainty of ground conditions plays a dominating role in these foundation projects. Effective risk management is a key success factor for profitable and sustainable operations of piling and deep foundations. It starts with a fundamental requirement to be aware of risks. Next the different risk perspectives of all stakeholders in any foundation project have to be acknowledged. A simple and structured risk management approach is introduced, to demonstrate that effective risk management is not necessarily that complicated. A major element is the contractual allocation of risks, as a result from differing ground conditions. It is based on the so-called Geotechnical Baseline Report (GBR). The main objective of the GBR is to provide a clear contractual arrangement for the allocation of risks, arising from differing site conditions. The benefits of explicit risk management in general and contractual risk allocation in particular are illustrated with an example and experiences. The presented structured risk management approach, including contractual risk allocation, is still rather new. It proves to be promising for cost-effective risk control of piling and deep foundation projects, anywhere in the world.

Jan 1, 2006

By Larry Stearns, Lori Tiefenthaler

Remediation of contaminated soil represents a significant market for application of Deep Soil Mixing (DSM). Eighty-one percent of U.S. Environmental Protection Agency (EPA) Superfund Program’s site remedies have involved contaminated soil. Contaminated soil is frequently treated by In-situ Solidification/Stabilization (ISS). ISS treatment of contaminated soil involves mixing binding agents into soil using DSM techniques. DSM is a core business for many DFI members. Members may improve and broaden their services to clients by learning about the recent ISS treatment of contaminated soil at a Superfund site. ISS treatment is part of the EPA-selected remedy for a Superfund Site in the metro New York City area. The property has seen heavy industrial use for more than a century. Soil at the site is contaminated with a variety of volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs) including coal tars and heavy metals, principally arsenic and lead. Beginning in 2017 and continuing through 2018, approximately 150,000 cubic yards (115,000 cubic meters) of soil will be treated by ISS at the case study site. Portland cement and slag cement are mixed into the soil by DSM techniques using GPS guided excavators to immobilize the hazardous constituents within the treated soil. ISS treatment by DSM will contribute to redevelopment of this valuable property. This paper will describe ISS constructability and performance, case study grout mix design with geotechnical results for strength and permeability, and deep soil mixing techniques. INTRODUCTION In-situ solidification and stabilization (ISS) is a deep soil mixing (DSM) technique applied in the environmental remediation field to physically encapsulate, or chemically bind, contaminates of concern such that the impacts to human health and the environment are mitigated. Common remediation applications of ISS include mixing cementitious reagents into contaminated soils to form a monolithic mass with desired performance characteristics, and the installation of vertical subsurface walls designed to control groundwater movement. A key characteristic of ISS is that the contaminated soils are treated in their existing location at the project site and then are left in place after treatment. Typical performance characteristics of the ISS treated soils include improved unconfined compressive strength (UCS), reduced hydraulic conductivity (HC), and reduced leaching potential of soil contaminants. Increased shear resistance of the treated soil may also be a performance requirement where seismic loading is a concern.

Jan 1, 2018

By Stefano Pirrello

"Sydney’s booming real estate market has pushed property developers to invest in historically “no-go” areas, which were previously too expensive to develop. These areas are usually near rivers where the sites are underlain by deep alluvial and estuarine sediments. In these ground conditions conventional bored pile techniques are often not competitive. Contiguous Flight Auger (CFA) and Drilled Displacement Piles (DD) techniques are on the other hand suitable for these ground conditions. This paper deals with the design and construction challenges encountered with these piling techniques for a series of high-rise towers in Sydney’s West. The advantages of DD over CFA piles such as reduced overall spoil with substantial cost savings and achievable rock sockets in medium strength bedrock are discussed. Design validation through interpretation of real-time data from the piling rigs’ on-board computer data, and low and high strain pile dynamic testing (PDA) is discussed. Testing data is presented as CAPWAP (Case Pile Wave Analysis Program) analyses for different concrete grades.INTRODUCTIONThe booming real estate market in Sydney has pushed property developers in investing in historically “no-go” areas, which were previously too expensive to develop. These areas are usually near rivers where the sites are underlain by deep alluvial and estuarine sediments. In these ground conditions conventional bored pile techniques are often not competitive. Contiguous Flight Auger (CFA) and Drilled Displacement (DD) Pile techniques are on the other hand suitable for these ground conditions and were utilised using concrete injection methods. This paper deals with the design and construction challenges encountered with these piling techniques for a series of high-rise towers in Sydney’s West.GEOLOGY & GEOTECHNICAL CHARACTERIZATION OF THE SITEThe Sydney 1:100 000 Geological Series Sheet shows that the site is underlain by man-placed filling and alluvial/estuarine sediment. The sediment comprises silty to peaty sand, silt and clay. Shell layers are also expected to be present within the soil profile. The Prospect/Parramatta River 1:2500 Acid Sulphate Soil Risk Map shows the site as ‘Disturbed Terrain’ in which soil investigations are required to assess acid sulphate soil potential. Several Cone Penetration Tests and Boreholes were carried out during the geotechnical investigation. All boreholes were extended to bedrock and NMLC-sized diamond core drilling was used to obtain 50mm continuous core of the rock, enabling unconfined compression strength testing to be carried out on selected samples. A summary of the ground conditions encountered on this site and inferred from the CPTs can be described as follows:"

Jan 1, 1900

By Dilip Khatri

Helical pile anchors have gained acceptance over the past sixty years. Most recently they have been commonplace in the 20th century for the power utility industry in anchoring transmission towers, equipment platforms, street lighting, telephone poles, and radio tower applications. They have a strong proven industrial track record in these industries. As the cost of conventional deep pile foundations rises, the practical benefits of helical pile anchors becomes evident as a practical alternative. Noted for their uplift capacity, helical piles demonstrate equally strong compressive capacity as a structural foundation element. This paper summarizes the history, practical benefits, and technical requirements for helical piles. Significant structural testing has been completed at various universities. The practical benefits of these tests are discussed. One case example of proven performance is presented to demonstrate the advantages and disadvantages of helical pile anchors as suitable foundation elements.

Jan 1, 2003

Port Gaspé is located on the back side of Gaspé bay and is protected by a natural sand barrier with a length of 2,5 km, from which it got its name, Gaspé Sandy Beach (1). Since 1904 the Gaspé region had a deep water wharf, initially very different, in fact, from the one existing just before the recent reconstruction (2). This wharf with a length of 228 m and a width of 23 m was build of timber cribs. The outside walls of these cribs had been doubled with a wooden wall, creosote impregnated to provide resistance to decay and to the attack of marine organisms (limnorias) (3). Fifteen years ago the upper part of the wood construction had to be removed, because of progressing rottenness and was replaced by an L-shaped reinforced concrete structure (4).

Jan 1, 1987

By Ganesh Kumar S.

"Soil reinforcement using stone columns is one of the well-developed ground improvement techniques for soft clay deposits. The load carrying capacity can be further improved by encasing it with geosynthetic material around the column which offers effective lateral confinement, prevents column contamination with improved drainage and strength characteristics. Improvement of undrained shear strength using vacuum consolidation is a type of hydraulic modification technique in which negative pore pressure will be developed which increases the effective stresses in soil without changing the total stress. The improvement in effective stress resulted in improved undrained shear strength of surrounding soil. In this research work, combined geosynthetic encased stone column and vacuum treatment method is examined for improving of extremely soft clay soils. The improvement in the time rate of consolidation and load carrying capacity of stone columns after vacuum treatment was studied using experimental investigations. It was observed that both load carrying capacity and stiffness of the encased stone column increased significantly with vacuum application. Also, application of vacuum accelerates rate of primary consolidation settlements. With this reduction in time, the construction activity can be accelerated which makes the project economically beneficial.INTRODUCTIONThe rising demand for the land for country’s infra-structure compels the engineers to work with even soft clay deposits which are not suitable for construction activities. As these soils have low bearing capacity and excessive settlement characteristics, ground improvement methods will be required before commencing construction. Among all available treatment methods, soil reinforcement and hydraulic modification technique are well-known popular techniques for its reduction in time required for consolidation settlement with improvement in load carrying capacity. When stone columns are used as a reinforcing member, it creates drainage with improves bearing capacity (Greenwood, 1970; Mitchell & Huber, 1983). However, the limitation includes lack of lateral confinement in very soft clay deposits, possibility of contamination, reduction in drainage path all which leads to the failure of stone columns (Mckenna et al, 1975). To overcome these limitations, encasement using geosynthetic material was adopted around the column which offers better lateral confinement, prevents intrusion of finer clay particle inside the column and provides effective drainage path with improved load bearing capacity characteristics (Van Impe, 1986; Raithel et al. 2005; Short et al. 2005; Borkemper et al. 2006; Murugesan & Rajagopal 2010; Kumar et al. 2014)"

Jan 1, 2017

By Kanchan K. Sen

The North Shore Connector (NSC) project will extend the Allegheny County Port Authority?s Light Rail Transit System from downtown Pittsburgh below the Allegheny River to the North Shore via twin bore tunnels. Jet grouting, diaphragm walls, and soil mixing were selected as cost-effective technically viable ground improvement and support of excavation techniques. Jet grouting was specified to provide break-out (egress) and break-in (ingress) block sections at the tunnel boring machine (TBM) launching and receiving pits. Jet grout treatment was also used adjacent to buildings with shallow foundations and below retaining walls along the tunnel alignment. A new method for measuring jet grout column diameter based on electrical resistivity was employed on the project. New equipment was introduced in the U.S for constructing soil mix temporary support of excavation using a soil-mix technique termed Cutter Soil Mixing (CSM) due to the use of two vertical cutting wheels that have evolved from diaphragm wall trench cutter technology. The system allows for continuous water tight soil mix panel construction including steel beams. This paper highlights some applications of jet grouting and various support of excavation systems (e.g. slurry walls, cement bentonite walls and CSM walls), including new innovative techniques (e.g. Cyljet and CSM) used under the constraints of an urban environment.

Jan 1, 2010

By W. J. Kingwell

Where the equipment, technique and materials are available for the construction of large diameter rock socketted piles, this is frequently the most economical and environmentally acceptable method of supporting very large concentrated foundation loads in geoglogically appropriate areas. This paper outlines the current approaches in Australia to design and installation of large diameter rock socketted piles. The equipment and procedures described generally reflect those developed or used by Vibro-Pile (Aust.), a company which, while installing the usual range of driven and bored piles, specializes in the design and construction of large diameter rock socketted piles and possesses special expertise in drilling in high strength rock. A high capacity crane attached drill for large diameter drilling in rock is briefly described. Discussed in detail are the construction techniques employed and structural and geomechanical design methods adopted.

Jan 1, 1989

By William Siegel

Kleinfelder provided foundation analysis and design for an expansion to a cement plant in Florence, Colorado. The expansion was a conversion from a horizontal wet process to a vertical dry process, and resulted in the construction of a number of structures with heavy foundation loads. [ ] The field investigation identified old fill and saturated sands and gravels above a shale/limestone bedrock environment. Based upon the anticipated loading, drilled piers socketed into bedrock were recommended. The structures were constructed in accordance with the design recommendations.

Jan 1, 2007

By Douglas L. Scaggs

Driving piles in under water applications has become more common place over the past twenty years. Where only a water depth reachable with a follower or dewatered cofferdam was the rule in the past, newer technologies developed for the offshore oil and gas industry have made depths of even several thousand feet possible offering new possibilities in foundation design and installation. With the new technology, engineers can now more efficiently design structures by placing foundations optimally thereby reducing weight and cost of the overall structure.

Jan 1, 2013

By Pawan L. Sethi

Design and construction of deep foundations and basements is increasingly becoming more complex, as the density and frequency of urban development increases. This growth brings various associated challenges in the form of design considerations and construction challenges. This paper discusses some of the challenges routinely encountered as well as some specific complications in this area, based on author’s experience gained through exposure as specialist contractor (designer), consultant and specialist consultant, along with some information on how these challenges were overcome. The paper highlights some of the key aspects of design coordination and importance of having an awareness of the overall perspective. Examples will be used to illustrate practical problems and the approaches used to respond.

Nov 1, 2022

By George C. Webb

A wide variety and variable depth (up to 40 ft.) of compressible, uncontrolled fill (including construction debris and a perched water condition) was present at a proposed Kroger construction site in Dent, Ohio. An innovative solution using a combination of an ACIP foundation system with a Tensar geogrid reinforced load distribution platform was used to provide a high quality building pad. This system allowed the use of conventional shallow foundations for structure support. This system was used in lieu of more costly solutions, such as complete undercutting of the entire existing fill and replacement with engineered fill or a deep foundation/ structural slab system. The selected ground modification included a system of augercast piles bearing on shale bedrock, which were installed on a grid pattern over the entire building footprint. Then, three layers of Tensar polypropylene biaxial geogrid were used to create a reinforced soil mat, which was supported on the augercast piles. An eight-foot blanket of engineered fill was placed above the geogrid-reinforced mattress fill to establish the building subgrade elevation. Standard shallow footings and slab-on-grade construction methods were then used to support the 26-ft. tall masonry block building. A small-scale instrumentation program included monitoring the geogrid reinforced mat settlement, geogrid strain and earth pressure distribution under the reinforced mat to evaluate design assumptions and theoretical analyses. This case history describes the first application of a pile supported geogrid reinforced mat for structure support which has been documented in the United States.

Jan 1, 2005

By George C. Webb

A wide variety and variable depth (up to 40 ft.) of compressible, uncontrolled fill (including construction debris and a perched water condition) was present at a proposed Kroger construction site in Dent, Ohio. An innovative solution using a combination of an ACIP foundation system with a Tensar geogrid reinforced load distribution platform was used to provide a high quality building pad. This system allowed the use of conventional shallow foundations for structure support. This system was used in lieu of more costly solutions, such as complete undercutting of the entire existing fill and replacement with engineered fill or a deep foundation/ structural slab system. The selected ground modification included a system of augercast piles bearing on shale bedrock, which were installed on a grid pattern over the entire building footprint. Then, three layers of Tensar polyproplene biaxial geogrid were used to create a reinforced soil mat, which was supported on the augercast piles. An eight-foot blanket of engineered fill was placed above the geogrid-reinforced mattress fill to establish the building subgrade elevation. Standard shallow footings and slab-on-grade construction methods were then used to support the 26-ft. tall masonry block building. A small-scale instrumentation program included monitoring the geogrid reinforced mat settlement, geogrid strain and earth pressure distribution under the reinforced mat to evaluate design assumptions and theoretical analyses. This case history describes the first application of a pile supported geogrid reinforced mat for structure support which has been documented in the United States.

Jan 1, 2003

By Shreyas Giridharan, Fursan Hamad, Sujith Gowda, Christian Moormann

"Pile installation in soil is a dynamic process which exhibits large deformation in the soil region. Experimental investigation of pile installation is both time and resource intensive. Numerical investigation can be a helpful tool for the analysis of the installation process. Furthermore, numerical analysis allows simulating various soils and loading conditions with ease. Finite Element Method (FEM) – a widely used framework for numerical simulations - fails to perform well for soil mechanics where large deformation and heavy material movement exists. In order to alleviate this shortcoming, Material Point Method (MPM), advancement to FEM has been used. In MPM, material points (particles) are used to represent the domain which carry the information and move over a fixed computational mesh where the governing equations are solved.In the present work, a variation of MPM, called CPDI (Convected Particle Domain Interpolation) is utilised which handles large deformation problems better than the classical MPM. Here, the material points are represented by a spatial domain which deforms according to the particle deformation. This eliminates stress oscillations while particles cross the grids. Implementation is validated and applied to pile installation in dry and saturated soil conditions. A 2D axisymmetric model is chosen, with penalty function method being used for evaluating contact between soil and pile. Sand is modelled via the hypoplastic constitutive description that takes into account large deformation, as well as small strain stiffness. From these simulations, various parameters like stress, void ratio and friction angle are studied.INTRODUCTIONOffshore piling is challenging in terms of testing and execution. Before the execution, predicting an efficient installation method requires study of various parameters, like soil conditions, type of loading, force requirement etc., and are the minimum parameters to be known beforehand. To obtain these parameters, testing a real scale prototype under different conditions is not feasible. Scaled model tests in lab can support in making certain decisions, but fail to replicate real behavior fully. Therefore, the need for a numerical simulation technique emerges, which can provide early predictions easily and accurately. This later can be extended to real scale tests, reducing the number of experimental investigation required.Simulation of displacement pile installation in sand involves large deformation due to penetration process, thereby making the application of FEM impossible, where large deformation causes heavy mesh distortions. Due to this, meshless methods are developed to treat large deformation in a better way. Among various meshless methods, Material Point Method (MPM) shows more applicability to geomechanical problems. This is mainly due to the ease of handling soil, structure and water in a unified manner."

Jan 1, 2017

By Kirk Ellison, Sherif Elfass, Ramin Motamed, Kevin V. Stanton

"The determination of accurate load transfer curves are essential for estimating deep foundation loadsettlement response using t-z style analyses. While recently developed semi-empirical methods from Ashour et al. (2010) and Ashour & Helal (2012) have shown promise in preliminary studies, they have not yet been thoroughly benchmarked against a more widely accepted approach. To address this issue, these recent procedures are implemented in the computer program CGI-DFSAP to predict the results of four Osterberg-cell (O-Cell) load tests. These predictions are compared to outcomes obtained following the recommendations from Reese & O’Neill (1988) for t-z analyses of drilled shafts in sand and clay which are carried out with the program TZ-PILE. Overall, the results suggest that the new approach offers improved accuracy regarding predictions of drilled shaft response to axial loading.INTRODUCTIONThe behavior of axially loaded deep foundations is often analyzed using a technique known as the t-z method. In this method, deep foundation elements are broken into multiple segments which are supported by discrete nonlinear springs to capture the contribution of both side-friction (t-z springs) and end-bearing (Q-z springs). Hence, the t-z and Q-z relationships dictate the predicted load-settlement response. A number of different approaches have been developed to estimate load-transfer curves with some relying solely on empirical data from laboratory and field experiments (i.e. Coyle & Reese, 1966; Vijayvergiya, 1977) and others based mainly on analytical frameworks (i.e. Kraft et al., 1981; Randolph, 1994). Reese & O’Neill (1988) provide recommendations which are widely used for developing t-z and Q-z curves for analyzing drilled shafts. This method is hereafter referred to as Method 1 (M1). It should be noted that these empirically derived relationships are only applicable for problems associated with drilled shafts and are therefore not appropriate for developing load-transfer curves for other types of deep foundations (i.e. driven piles). This is because of the difference in the frictional resistance which can be developed between a circular concrete-soil interface as opposed to that of other materials (i.e. steel) and/or different cross sectional geometries.The M1 load-transfer curves form the basis for the t-z analysis of drilled shafts implemented in the computer program TZ-PILE (Ensoft, 2014). In light of this, TZ-PILE is employed herein as a reference to compare against the capabilities of another method of implementing t-z style analyses. This method is based on a semi-empirical framework for soil behavior developed by Norris (1986) and is implemented using the program CGI-DFSAP (Computers & GeoEngineering Inc., 2011). More information concerning this approach, hereafter referred to as Method 2 (M2), is given in subsequent sections."

Jan 1, 2017