Search Documents

By Inc. Pile Dynamics, Daniel S. Belardo, Marcus Galvan, George Piscsalko

Soil nails are often utilized as a temporary or permanent earth retention technique for slope stabilization and for excavation retention for existing or new structures. Soils nails are generally advantageous as installation is relatively rapid and they can be installed beneath existing structures and where site access for equipment is limited. Due to the typically small cross-section of these elements, the inability to inspect the holes prior to grouting/concreting, and the various installation techniques utilized, quality control for assessing the integrity along the entire length is limited. Currently, quality assurance is conducted by load testing to verify the pull out capacity after installation. The load testing is typically done on a small percentage of the total number of soil nails. This paper will provide the results of a demonstration where the new Non-Destructive Test (NDT) method Thermal Integrity Profiling (TIP) was used to access the integrity of several soil nails along their entire lengths. This TIP method has been successfully used for several years to assess the integrity in drilled shafts and ACIP piles. The TIP method assesses the integrity across the entire cross-section and can identify regions where bulges, necks, and insufficient grout/concrete are present. TIP testing can also help assure that the contractor's installation methods are adequate and consistent for the intended design. For the project presented, instrumented Thermal Wire were affixed to the centered tension bars prior to placement in the excavated shafts. Temperature measurements were recorded from the hydration energy generated after grout/concrete placement, capturing the entire heating cycle. Manufactured defects were installed on the center bar at multiple locations. The results and conclusion will be discussed as well as recommendations for future use.

Jan 1, 2017

By David White

"When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100’ of water are well known, let alone in the open waters of the South China Sea.In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130’ long, 72’ diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE’s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.INTRODUCTIONThe challenges of driving individual steel sheets in deep water are well known, let alone in the open waters of the South China Sea. Often the challenges of construction are overcome with engineering or equipment. The challenges of China’s Hong Kong-Zhuhai-Macau Bridge, on the drawing board since 1983, were to overcome both. The challenges of overcoming the skepticism of the Chinese Engineering community would be another story.The finished project will comprise three cablestayed span bridges and a 4.15 mile immersed tube tunnel linking Hong Kong on an eastern span to the China mainland cities of Zhuhai and Macau via two western spans."

Jan 1, 2017

By Kim Chan, Bryn Thomas, Ben Dening

"Increased rail capacity is required into Kooragang Coal Terminal near Newcastle, NSW, Australia to relieve rail traffic congestion and improve management of train arrivals. An additional arrivals track is proposed on new embankment within a heavily constrained site located between existing railway tracks, a high pressure gas pipeline located 7m beyond the toe of the embankment and an environmentally sensitive wetland area. Ground conditions at the site consist of deep soft estuarine clays, a soil profile which is consistently encountered throughout this part of the east coast of Australia. Upon determining that a ground improvement solution was required to ensure global embankment stability, various solutions were considered including a piled viaduct, retaining walls, dry deep soil mix (DSM) columns and concrete injected columns (CICs). DSM columns were adopted as the design solution, a decision which was driven by the presence of sensitive infrastructure and a confined site. DSM offered further advantages including reduced impacts on temporary working platform design, where the use of a thinner platform could be justified owing to the lower track loads of a DSM rig relative to other ground improvement techniques.INTRODUCTIONThis paper presents a case study of the design of DSM ground improvement works to provide support for and enable safe construction of a new railway embankment over deep soft soils with a number of nearby infrastructure and other constraints. The project site is approximately 1km long and is constrained by existing railway tracks, a high pressure gas pipeline and a wetland area of ecological significance. Due to the site constraints and ground conditions, a number of ground improvement techniques were considered during the design process, with DSM columns eventually adopted. This paper discusses the design development and the particular suitability of the technique for use in this application.SITE DESCRIPTIONLandformThe site is located along the northern boundary of the Kooragang Coal Terminal (KCT) at Kooragang Island (KI), a collection of former islands located near the mouth of the Hunter River, north of Newcastle, NSW. The topography of the original area was generally flat with mudflats, swamps and mangroves existing along tidal water courses. Subsequent dredged fill reclamation and development has amalgamated the previous islands into the current KI. The site area extends over numerous channel infills including the buried former course of the Moschetto Channel (paleochannel).Figure 1 shows the proposed 1km long new rail corridor construction area in relation to the various natural and man-made site constraints including existing tracks, the high pressure gas pipeline, the wetland area and the existing reclaimed area."

Jan 1, 2015

By Rajarshi Pramanik, Nirjhar Dhang, Dilip K. Baidya

"This paper performs the reliability evaluation of pile foundation under vertical loading condition using the concept of fuzzy set theory. The uncertain parameters are expressed as fuzzy numbers. Monte Carlo simulation technique in conjunction with fuzzy set theory and fuzzy reliability index approach are implemented in evaluation of the probability of failure of pile foundations. The results are validated through some well established methods such as, First Order Reliability Method (FORM), Second Order Reliability Method (SORM), and direct Monte Carlo Simulation (MCS). Response surface method (RSM) is used to approximate the original limit state equation through second order polynomial. The effect of the position of the water table is also highlighted. Finally, the effect of the variation of applied load is examined and it is observed that the fuzzy reliability analysis gives more conservative estimate of failure probability than the other methods.INTRODUCTIONCivil engineering structures, such as high rise buildings, bridges, offshore platforms etc. are always subjected to vertical as well as horizontal loads. To support these structures, pile foundations are generally the solution in most of the situation. It transmits load from the superstructure to soil at a reasonably great depth. This transfer may be by vertical distribution of the load along the pile shaft or a direct application of load to a lower stratum through the pile tip. Different methods are available to estimate the capacity of piles embedded in different types of soil and under the application of vertical and horizontal loading. To consider the variability in soil and other unforeseen able situation, generally a reasonable value of factor of safety is used to estimate the designed capacity of the pile. Recent developments have shown a trend to place the treatment of uncertainty on a more formal basis, in particular by applying the results of reliability theory to geotechnical engineering. Keeping in mind the importance of pile foundation in the engineering structures it is essential to maintain a high structural safety which result in increase in reliability. The probability theory has been proved to be a powerful tool for representing variability in mathematical models. The variability associated with soil parameters and the modeling uncertainties are needed to be considered for the reliability assessment purpose.Recent development (Zhang et al. 2005; Misra and Roberts 2006; Haldar and Babu 2008; Basu and Salgado 2012; Teixeira et al. 2012; Pula and Rozanski 2012; and Chan and Low 2012) showed that the reliability analysis of pile foundations subjected to axial as well as lateral load has been one of the important current research topic in geotechnical field. Probabilistic based performance criteria were quantified for a single pile and pile groups in cohesionless soil by Eloseily et al. (2002). A p-multiplier approach was incorporated into the analysis to modify the p-y curve for a single pile to obtain the p-y curve for individual piles in a pile group. A statistical analysis of set up capacity of pile was carried out from the database of a large number of pile testing data in clay by Yang and Liang (2006). Load and resistance factor design (LRFD) using FORM was used for examining the different load and resistance factor for different target reliability index. Limit state analysis of drilled shaft was performed by Misra and Roberts (2006) in probabilistic framework. The fuzzy based reliability analysis (Dodagoudar and Venkatachalam 2000; and Park et al. 2012) of the earth slope was reported in the literature. Dodagoudar and Venkatachalam (2000) presented a new approach, called fuzzy point estimate method (FPEM) for reliability evaluation of earth slope. Park et al. (2012) reported a hybrid approach, fuzzy set theory in conjunction with Monte Carlo simulation technique, to determine the failure probability of earth slope. Second Order Reliability Method"

Jan 1, 2015

By Peter J. Nicholson

"IntroductionDuring my more than 40 years in the practice of underground construction and engineering, the industry has seen progress from the dig down to rock or hardpan or alternatively drive concrete or steel into the ground and count the blows; then you can be sure of you have a solid foundation; to the modern day, I’m willing to try anything to save money. Of course these are both exaggerations, but not gross ones. After getting bored being supervision on jobs counting blows, I struck out into the new field of “tie-backs” as they were called in the United States, or “ground anchors” as they were then termed in the United Kingdom. After installing some of the first permanent ground anchors for the Corps of Engineers on Lake Michigan as well as the highest loaded rock anchors of the time at two dams on the Ohio River, we were at the top of our game in the 1970’s. Subsequently in the 1980’s when my view of the future of ground anchors saw their installation becoming a commodity item, we branched out into “Pin Piles” now known as Micro Piles, high capacity, steel tube encased, small diameter (5-12” or so), high capacity (100-500 tons) piling. Next came soil nailing, both temporary and permanent retaining walls, as at Cumberland Gap Kentucky. My next morph was into “Cement Deep Soil Mixing” earlier on, known simply as “soil mixing”. For this education I traveled to Japan several times and established a long-term, Joint Venture, relationship with one of the better known Japanese specialty ground modification companies. In Boston at the “Big Dig” we established the then record size soil mixing project, 500,000 or so cubic meters of CDSM concluding in the year 2000. Since then I’ve been involved as a consultant mainly for dams and levees. Below is the story of how I came to be at this place in the road to innovation in Geotechnical processes."

Jan 1, 2017

By David White

When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100? of water are well known, let alone in the open waters of the South China Sea. In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130? long, 72? diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE?s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.

By Stephan A. Jefferis

I presume that the questioner is not asking about the reduction of sulfate in groundwater to hydrogen sulfide as a result of biological activity promoted by organics in the grout hardener and that the question relates to sulfate attack on cementitious grout systems. For the project in Spain presented in my paper, we used a very high pulverized fuel ash (PFA) content in the cementitious material. This gives good sulfate resistance and indeed the chemical interaction will actually cause the permeability to drop for about 50 years without any question of sulfate attack and damage to the whole thickness of the grout - of course there will be attack at the exposed face of the grout where it is in contact with the contaminated groundwater. The mix had over 75% PFA, and also a very high overall cementitious content. The mix was the contractor's design and showed excellent behavior in laboratory proving trials. In grouts as distinct from concrete, PFA gives significantly better sulfate resistance than ground granulated blast furnace slag which is often used in Europe as a component of bentonite-cement mixes for slurry trench cut-off walls.

Feb 10, 2003

By Song-yu Liu, Chao Yan, Yong-feng Deng

"In order to investigate the stability of embankment on soft subgrade improved by T-shaped deep mixed column composite foundation, the internal forces and failure modes of columns were analyzed on the shape of critical slip surface and the displacement fields of composite foundation through strength reduction method of three dimensional numerical simulation. Then comparison between T-shaped and conventional deep mixed column composite foundation were conducted. The simulation results indicate that the stability analysis was overestimated by limit equilibrium methods. Piles within the slope shoulder provide great resistance slide effect through the vertical bearing capacity, while the piles nearby slope shoulder and outside slope shoulder providing great moment to resistant slip. The embankment stability of T-shaped deep mixed column composite foundation is higher than that of conventional deep mixed column composite foundation while cost less cement and construction time.INTRODUCTIONThe soft soil has many unfavorable project properties such as high compressibility, low strength, and high water component. Embankment built on the soft soil will face subsidence, horizontal displacement and stability problems. Cement-soil deep mixed column composite foundation is more commonly used as a method for construction of embankment on soft ground [1-2]. For the existing problems of China's current cement-soil pile (wet jet mixing pile), including strength uneven, effective treatment with shallow depth and high cost, a new technique, T-shaped bidirectional deep mixed column, is introduced [3]. An automatic expanding mixing blade was developed by Liu et al. shown in Figure. 1, to install TDM columns [4].T-shaped deep mixed (TDM) column combines bi-directional deep mixing technique and T-shaped deep mixing technique: ?Using concentric biaxial drill pipe, opposite rotational direction of the blade on the inner drill pipe and the outer drill pipe. By squeezing action of the blade on the outer drill pipe, forward and reverse rotation of the blades bidirectional mixing at the same time, blocking the way to take the grout, the uniformity of cement mixing is improved. ?Scalable stirring blades, which can be stretched for two different radius at any depth below ground, expand cross-section of the upper pile (enlarged head), forming expanding cross-section within the upper part of a certain depth which is similar to the shape of nail. As a new composite foundation, T-shaped mixing pile composite foundation is widely applied. However, studies on the stability of T-shaped column treated soft subgrade are rare in the research. So the stability study on T-shaped column composite foundation under embankment for guiding the design and construction has important significance."

Jan 1, 2015

By Chunli Wei, Mark Jen, Xiaojun Wang

"After more than 85 years of service, a critical link between New York and New Jersey, the Goethals Bridge over the Arthur Kill waterway, is being replaced with two new parallel bridges. Each bridge includes 1,650 feet long signature steel composite cable-stayed bridge, a 2,789 feet long New York approach and a 1,889 feet long New Jersey approach. The superstructure of each approach is supported on a series of two-column concrete piers and each column is supported on a single large diameter drilled shaft varying from 4.5 to 9 feet in diameter and anchored 45 feet below ground into the underlying rock.A performance-based methodology was followed for the strength and extreme event limit states design of the drilled shaft foundations. The design for seismic loads has been performed using the AASHTO Guide Specifications for LRFD Seismic Bridge Design. For all strength and service loads, the AASHTO LRFD Bridge Design Specifications were used. Since the longitudinal and confinement requirements in the two specifications vary, the minimum longitudinal reinforcement was based on the more stringent requirements of the two codes. A design example is presented to illustrate the methodology in bridge deep foundation design using nonlinear time-history global analysis results with soil-pile interaction represented by sets of horizontal and vertical nonlinear soil springs along the drilled shaft, based on the soil and rock properties from the boreholes test results. In this paper the design methodology implements strain limits related to earthquake intensities and damage levels to calculate the capacity using XTRACT analysis, which aids designers to adopt applicable provisions that meet specific design requirements.INTRODUCTIONAfter more than 85 years of service, a critical link between New York and New Jersey, the Goethals Bridge over the Arthur Kill waterway, is being replaced with two new parallel bridges designed to carry vehicular traffic and a future mass transit corridor. They include two 1,650 feet long signature steel composite cablestayed bridges with 260 feet tall V-shaped concrete gateway towers (Figure 1). The approaches consist of continuous pre-stressed concrete girders. The New York approach is a single structure consisting of 18 continuous spans, sloping at 4% for a total length of 2,789 feet without expansion joints. Similarly, the longest continuous portion on the New Jersey approach, with a similar slope, consists of 11 spans for a total length of 1,889 feet without expansion joints. The superstructure of each approach is supported on a series of two-column concrete piers that vary in height from 121.3 feet near the cable-stayed bridges to 11.8 feet near the abutments. Each column is supported on a single large diameter drilled shaft varying from 4.5 to 9 feet in diameter and anchored 45 feet below ground into the underlying rock."

Jan 1, 2016

By Anburaj C., Srinivas A.

Deep excavation with support system is required to construct various part of underground structures like shafts, stations and entry structures etc. These structures have to be constructed using permanent or temporary embedded retaining walls with support system. The selection of a suitable type of retaining wall will depend upon the geological condition present in the particular location, time, cost and available equipment etc. In Bangalore Metro Rail Project, secant pile wall is adopted as the temporary earth retaining system and depth of excavation is about 20 m. It is designed initially based on bottom up construction methodology with 3 level of struts and 3 level of anchors but at later stage due to time and other construction related issues, it is decided to change the configuration to 6 levels of strut. Generally, in deep excavations, all the underground structures should be designed and checked for the critical forces from both permanent stage and construction stages. Since, secant piles are used as temporary retaining wall, only construction stage analysis is carried out to get the governing forces and deformation. In construction stage analysis, soil layers are defined with boundary conditions and the surcharge during construction and surcharge from actual building near the secant pile are considered. This paper discusses the effect of change in the support system from anchors to struts and how these changes in the support system affect the behavior of secant pile and subsequently adjacent buildings present in the influence zone of the excavation. As a result, in changing from anchors to struts, the wall displacement, strut forces and ground movement on the adjacent ground and buildings increases. The increase in deflection, ground movements and strut forces occurs during backfilling sequence of the underground station excavation. During backfilling, struts has to be removed and this imparts higher magnitude in deflection, strut forces and ground movements.

Nov 1, 2022

By Amr Sallam, Ahmad Mohamed, Mohamed Alrowaimi

Renewable energy, in the form of wind and solar, has emerged as main source of energy in the modern society. The wind industry has substantially grown over the last two decades to become a key player in providing energy to public. Wind turbines are getting larger, taller, and more efficient every year. The foundation is a major component of the wind turbine system. The wind turbine foundation must provide short and long-term stability for the overall turbine to allow continuous and safe turbine operation for energy production. The turbine serviceability and stability requirements must be geotechnically and structurally satisfied. In North America, major foundation types currently utilized in the wind industry include gravity spread foundation, mono pier foundation, and pile foundation. In this case study, a Post Tensioned Pile Cap (PTPC) foundation was used to support a 3.15-3.4 Megawatt turbine with 125M Rotor supported on 87.5M-hub-height tower. Soil anchors in the form of Auger-Pressure-Grouted-Displacement (APGD) piles and Continuous Flight Auger (CFA) piles were utilized. Four distinct subsoil conditions were identified, and for which four pile designs were adapted. Due to the occasional encounter of stronger soils at 50 to 55 feet (15.2 to 16.7 m), shorter pile design was preferred. To satisfy the design uplift load, pile post grouting were utilized to increase the shaft capacity of the piles. In this paper, the pre-production pile load test program will be described. The pile load test procedure, analysis, and results will be presented. A discussion will be provided, which led to the selection of the optimum pile design to support the high tension loads taking into consideration pile length limitations.

By P. Arz

With a total of five basement levels, ground floor and a further six levels above grade, construction of the Kö-Galerie building, on the Königsallee, in the centre of Düsseldorf, was completed with all the difficulties which accompany property development today in the inner city. To meet the intermediate and final deadlines, ad­vanced building techniques were used. Notable among them are the top/down method for simultaneous construction upwards and downwards from an intermediate level, and the use of pre-fabricated composite columns in drilled shafts for the main load-bearing foundations as well as diaphragm walls designed as permanent structural wall of the basement.

Jan 1, 1989

By David S. Graham, Benjamin Turner, Paul J. Axtell

Seismic challenges were at the forefront of design for two parallel replacement bridge structures over the Arkansas River as part of the I-30 Crossing Project in Little Rock, Arkansas. Although not an area of the country typically associated with high seismicity, proximity to the New Madrid Fault Zone resulted in design ground motions sufficient to trigger liquefaction in alluvial channel and point bar deposits. A detailed post-award subsurface investigation program utilized CPT with complimentary borings to obtain samples for laboratory testing to assess the continuity of potentially liquefiable layers, from which we concluded that continuous zones of liquefaction across the extent of the north approach could lead to lateral spreading towards the river. An overview of the foundation and superstructure design to resist lateral spreading forces in accordance with the latest published design guidelines and research is presented. Other seismic aspects of the design are covered including timber pile ground improvement to mitigate liquefaction at the north approach embankment and foundation input motions that differ from code-based ground surface motions due to foundation stiffness, strength, and geometry. The project showcases an example of successful collaboration between geotechnical and structural designers with contractor input to address seismic challenges in the South Central US. Furthermore, the importance of considering kinematic demands on columns and other superstructure components – not just foundations – is highlighted.

Sep 8, 2021

By Djk Arentsen

A new technique to drive tubular piles by impact hammer inside the pile has confirmed a dramatic reduction of noise and the opportunity to save steel. Also a reduction in driving time and a higher bearing capacity has been observed during a test program of this technique. As part of the so-called "Down-the-hole" driving technique, a wave equation analysis has been developed to calculate driveability and pile stress. The main feature of the new "Down-the-hole" technique is the development of a patented device allowing uncoupled penetration of pile tip and pile shaft, which makes it possible to drive both closed or open end piles and reduce the stress level induced in the pile wall. During a test program, a number of instrumented piles were driven and compared with traditional driving of the same pile with the same hammer on top (also instrumented). Also the stresses and performances were compared with precalculations. This paper, explains the technique and presents the test and noise results, in comparison with traditional top-pile-driving. The "Down-the-hole" driving technique is an interesting alternative for special applications where traditional pile driving requires a large wall thickness or in areas where noise is a hot item.

Jan 1, 1996

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By S. Hardy

The paper describes state of the art non-linear analyses of the pile groups that were employed during the raising of the 133m high triumphal arch which forms the centre piece of the new Wembley stadium in North London. The deformation behaviour of these piles groups was critical during the lifting process, due to the slendemess of the arch structure. The issue was made more critical by the high profile nature of the project. The results of Class A (Lambe (1973)) predictions of the pile group movements are compared with observed displacements and rotations which were accurately measured on site. To illustrate the importance of soil non-linearity on pile group behaviour, comparison is also made with pile group analyses which assume a linear soil stiffness.

Jan 1, 2006

By E. E. De Beer

This paper describes a method for the determination of the settlement of an individual H-bearing pile, based on the results of CPT-tests. As implied by the nature of the problem, no analysis performed on one pile can be regarded as generally valid for a whole piling foundation project because, even on one site, the pile behaviour varies from one pile to another. Consequently, no precise mathematical analysis has been established; the proposed procedure represents a simple model for the determination of the probable settlement behaviour of an H-pile under a compressive load. Prior to the settlement computations, the rupture load and the resistance distribution along the pile have to be determined. Since the method for the determination of the H-pile bearing capacity from the results of CPT tests has been described elsewhere (de Beer, 1971, 72; de Beer et al., 1982; Arbed, 1985), no details will be given in this paper. The proposed method is valid for both uniform and non-uniform H-piles. The computed results have been satisfactorely compared to the static loading tests performed on different types of piles in clayey and sandy soils during an ECSC research program on H-bearing piles (1983-1987).

Jan 1, 1987

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By M. Melih Demirkan, Jared Deible, Michael Rosenmeier, Mazen Elias Adib, Juan J. Gutierrez, Raghav Ramanathan

Dewatering and groundwater control is required frequently for construction projects and needs to be accounted for and dealt with care during design and construction to complete the project successfully. Dewatering can cause changes in porewater pressure, which changes the effective vertical stress in a soil mass. Dewatering can also cause changes in groundwater chemistry which in turn can cause changes in porewater pressure and also dissolution of soluble minerals in the soil and rock. The Guideline developed in this study addresses the engineering issues, approaches to lessen the potential risks associated with construction dewatering, and presents dewatering practices to support dewatering applications regulated by the Municipality of Abu Dhabi City (ADM) in the United Arab Emirates (UAE). The subsurface condition within the city presents significant geotechnical problems due to presence of shallow subsurface cavities and soluble minerals in the soil and rock. Therefore it is critical to develop standards for dewatering practices to provide information for local dewatering engineers and contractors with special emphasis to control and to eliminate the subsidence/collapse problems related to dewatering projects within the Abu Dhabi city. The ADM is also responsible for approval of permit applications for projects that involve dewatering. In order to minimize the risk related to subsidence/collapse problems due to dewatering, construction companies and dewatering contractors need to be informed about possible mitigative measures that can be employed to reduce risks. The guidelines were developed as part of this study based on detailed analysis of the local subsurface conditions. A set of rules and regulations are developed for geotechnical and hydrogeological investigations, dewatering design and monitoring criteria depending on the hazard zones, proximity of excavation to critical structures, excavation depth. The Guidelines include examples of permit application packages for three types of dewatering projects; one involving shallow dewatering, one involving intermediate depth dewatering, and one involving deep dewatering. These Guidelines are considered as living document and will be updated as required, as additional information is collected and additional local experience is gained.

Jan 1, 2016

By Carnevale Francesco, Bracci Laudiero Alberto, Pampanin Piero

"SummaryIn the Port of Naples a slurry wall has been realized through a sandy layer up to a deep tuff layer using the Cutting Soil Mixing technique.The executed panels have dimensions of 2.8 m x0.65 m in plan and a total length of 25 m. Primary and secondary panels have been executed using the wet to wet technique. During the panels execution the following parameters had been measured: injection pressure, injected volume, verticality. At the end of the works an exploratory campaign has been carried out through boreholes collecting samples for laboratory tests in order to verify the diaphragm thickness and its physical and mechanical properties (i.e. unit weight, unconfined compressive strength).The interpretation of the collected data allowed to verify the efficiency of the method, the volume of slurry loss due to permeation during the panels execution, the quantity of the obtained spoil compared to the volume balance equation, both for the sand and the tuff layer.Eventually, the measured physical and mechanical characteristics of the panels have been correlated to the execution method performed.IntroductionIn the Naples Port area there is a polluted site which has to be hydraulically isolated in order to prevent the pollution of the groundwater that flows from land to the sea through the Port area. A hydraulic cut-off wall has to be realized and particularly a slurry-wall realized using the CSM method had been executed.To date, two stretches have been executed, 140 an 110 m in length respectively, as shown in Figure 1 and Figure 2.After execution, the slurry-walls have been investigated with boreholes. In-situ and laboratory tests on the recovered samples of grout have been carried out; furthermore, the geotechnical parameters of the mix composing the wall have been measured."

Jan 1, 2014