Search Documents

By James J. Cahill

Contractor's working in an urban environment face a multitude of working conditions. There is no typical "Downtown" job site. From afar we just see the skyline, or up close a specific building. This, of course, does not give us a clue as to the site conditions the foundation contractor faced in doing his work. The open, downtown building site is still available on some projects, but they are becoming rare as our cities are becoming more developed. A typical site today might include any one or several of the following problems: A. Deep pit with no ramp access B. Multi-type known or unknown obstructions C. Height limitations D. Load restrictions E. Existing adjacent building founded on shallow foundation F. Existing foundations G. Existing tunnels, utilities or subways

Jan 1, 1991

By Tim Chapman

This general report considers what promoters of deep basement projects want from their teams and whether they get it often enough. Most large projects are based on complex financial models where the funding is related to a future income stream. Project delays and cost over-runs can critically affect the financial model. Too often, delays and cost over-runs originate in the substructure and foundations. We must take positive steps to improve our industry's reputation for reliability.

Jan 1, 2006

By Li Huimin

In this paper the step of determining the property index and the program of mixture ratio design of stabilizing agent in deep foundation construction are presented. According to the principle of computer simulation, the model and the method of computer simulation for optimum mix design are set up. Also, the precision of simulation results has been estimated and verified experimentally.

Jan 1, 1991

By experience we know about the natural event of ocean-tides. In geophysics we say that the earth-tides phenomenon is the elastico-viscous response of the earth's body to the attraction potential of moon and sun. By the fact that the tides on the planet take place in a regular periodic frequency, due to the earth rotation of 24 houres for one cycle, the rotation of the moon in about 28 days around the earth and finally to the rotation of the earth-moon combination around the sun in 365 days this phenomenon is a very important one in geophysics. The exact calculation of the acting forces is possible and the comparison of the earth's body response to these forces as well.

Jan 1, 1987

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 fUsec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases. and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

May 11, 2007

By Frank J. Purcell

“Down The Hole” (DTH) hammer drilling is often necessary to advance the casing during pile construction where the test bores have determined difficult drilling conditions with obstructions such as boulders, cobble and glacial till. The use of compressed air to operate DTH hammers in foundation drilling has been a contentious point in many regions of the world due to its potential to disturb the ground around the pile being constructed. There are many examples of damage to adjacent building foundations where compressed air exiting the pile being drilled disturbed the subsurface around the building’s existing piles. This paper looks at the use of compressed air in DTH hammer foundation drilling and the move towards controlling the exhausted air to avoid over drilling the pile, causing potential damage to nearby piles. Simulated models of air flow penetration into the soil of different configurations of drill bits are discussed to highlight design changes employed to better control the air during the drilling process. A case study of the construction of a water-tight pipe pile wall for a building’s underground parking structure is studied to demonstrate the potential of DTH hammer foundation drilling where the air is fully controlled.

Nov 1, 2022

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 ft/sec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases, and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

Jan 1, 2013

By Bengt H. Fellenius

The design of pile foundations is much more commonly verified by means of a full-scale test, than is the design of other foundation units. The reason is not that our knowledge of pile behavior is more uncertain than our knowledge of other foundation types making the verification necessary, but more that the loads in a structure are more concentrated to single foundations in a structure founded on piles as opposed to structures on footings or mats. Therefore, should a pile cap fail or move, the adverse consequence of this is often drastic, as the piled structure has little freedom to transfer its need for support to other foundation units. Consequently, it becomes important to assure the design of piled foundations. In many, maybe in most instances, the static pile loading test is routine and geared toward determining an at least capacity, only. However, in these times there is an ever increasing liability of the professional, demands for increased economy of the foundation, and frequent lack of the involvement in the test of the experienced old-timer exercising good judgment. Furthermore, modern pile design is leaving the single, simple concept of capacity and requires more information from the test to assist in determining aspects of long-term behavior and settlement. Therefore, even the straight forward, routine static loading test requires improved planning, execution, and analysis.

Jan 1, 1990

By H. Yoshida

Jet grouting was first introduced in Japan in the second half of the 1960s, approaching 50 years ago. By the end of the first 40 years, jet grouting from single to triple fluid systems had become a global technology. In the last ten years, progress in the jetting has been remarkable, and operational efficiency has improved. The quantity of carbon dioxide emitted in unit soil improvement has become one-third that of the initial technology. Meanwhile, technologies in waste recycling and horizontal jet grouting are also emerging. This paper discusses developments in the most recent ten years.

Jan 1, 2010

By W. G. K. Fleming

The general history of piling is traced up to the present time with regard to the evolution of methods and materials. The processes have been strongly influenced by developments in basic equipment and industrial change. It is noticeable that in the twentieth century more progress has taken place than in the many previous centuries. It has been strongly influenced by the general development of Soil Mechanics. Test loading is probably the most effective way to assess the success of designs and many empirical relationships have been challenged through it. As we approach a new century it appears that it will be an age of rapid equipment development, with much enhancement of understanding of what has been done. Processes of automatic construction and testing will becoming commonplace. These changes will narrow the limits of conventional scatter that have come to be accepted and to a large extent will be driven by political efforts to curtail energy consumption, to raise standards of quality and reliability, and to conserve the environment. 1. Ancient history. Piling is an ancient art. Its first mention in history is from Herodotus, the first person to commit an account of his times to the written word in the years 557 to 479 BC. He evidently had a strong interest in engineering matters because he wrote of building, brick making, reinforced brickwork, river training, canal building, bridge construction, tunnelling and its acoustic detection and piling. The piling reference comes from Book 5 at paragraph 16.

Jan 1, 1999

By Filippo Maria Leoni, Wesley Schmutzler

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 90 inch forced sewer main relocation and to improve the soils for the base of a new drainage channel. The project is located just east of San Juan and south of the Horizon Port. The soils to be improved consisted of fill, marine clay, organics (peat) and the foundation clay layer. A preconstruction soil investigation campaign was performed to assess soil properties and to retrieve samples of the different soil layers for the laboratory Bench Scale Testing program (BST). The BST was conducted using various binder contents and water/cement ratios in each of the soil types; the selection of the different combinations and dosages was based on past extensive experiences on similar materials. Following the laboratory program, a full scale Field Test (FT) was done installing several DMM elements to verify the results of the BST and fine tune the construction parameters. Each element consisted of two 5.5 feet diameter overlapping mixing augers installed simultaneously to a depth of approximately 60 feet using a SOILMEC SR-90 dual axis drilling rig. The FT construction and post-construction coring results showed significant differences between the lab study and the actual field conditions. This paper will highlight these differences and the importance of performing both pre-construction laboratory and field tests in order to ascertain the proper mixing parameters in the different soil layers.IntroductionThe Puerto Nuevo project consists of the stabilization of a major drainage channel using Deep Mixing Method (DMM) and the relocation of a 90 inch forced main sanitary sewer outfall. The first portion of this project was a 40 x 16 x 2,000 foot box culvert installed in 2004. In order for the drainage system to be completed and function properly, the 90 inch forced main needed to be lowered about 20 feet to allow for proper drainage.DMM was chosen by the US Army corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The overall layout of the project is shown in Figure 1. The DMM is arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for ZONE A and B as an example. (Figure 2) The total amount of soils to be treated by DMM is approximately 84,000 cubic yards up to a maximum depth of 57 feet from ground surface and an Area Replacement Ratio of 100%.The equipment used to perform the DMM is a Soilmec SR90 twin-shaft jet assisted deep mixing rig (Figure 3) coupled with a LODOS 30 grout plant and two Soilmec 7T-500J high pressure pumps."

Jan 1, 2015

By Niels Krebs Ovesen

Close economic cooperation was established among the countries in western Europe during the seventies. As a consequence, among others, a need for harmonized technical specifications for civil engineering works arose. Technical specifications for design and execution of building and civil engineering structures exist in most of the European countries. In some countries such technical specifications are part of the building regulations and in other they are independent codes of practice and standards. The works on the Eurocodes was initiated by the Commission of the European Communities about 1976. The Eurocodes are intended as common unified design codes for different load bearing structures constructed from different materials. They are also intended to cover design of geotechnical structures. They are established with a view to promote the free movement of goods and services within the member states of the European Community - the so called Internal Market - and within the member countries of the European Free Trade Association, EFTA by removing obstacles arising from different rules for calculation and design.

Jan 1, 1994

By Jerold Bishop, Grant Bearss, Aleksey Egorov

"When a shock wave is released in the bottom of a drill hole filled with wet concrete slurry, the result is called an electrohydrodynamic effect, or EHDE. The energy is carried through the fluid with minimal loss because the slurry is an incompressible medium. Repetitive discharges provide a series of energy pulses that compact the soil along the pile shaft and at its base. The process is analogous to repeated applications of low-energy blast densification or to dynamic compaction. In general, the process is not depth dependent. EHDE was identified in the 18th century by an American scientist who observed that a spark between two electrodes placed under water induced a burst of pressure. In 1957, two Russian engineers formulated a process and received a patent for a method of creating a pressure wave by transforming power from an electrical discharge to a mechanical impact. They derived more than 200 applications for technical and industrial processes.In the 1970s, civil engineers at the Engineering and Building Institute in St. Petersburg, Russia, began to look at EHDE to improve the capacity of drilled piles. Early experiments showed that electric discharges in a wet concrete slurry mix could create a pressure wave of up to 26 MPa (3700 psi). Later tests demonstrated that this pressure level could be created in a drilled pile hole. The researchers devised equipment and in the early 1990s began to study pulse technology as applied to drilled piles.This application was accepted into the Russian Federation Building Code in the 1990s. The code treats “regular” drilled piles with equivalent bearing area as having roughly half the capacity of a driven pile. However, the code considers drilled piles treated with the EHDE technique a direct “one for one” substitution for driven piles and allows higher values if the capacity is established by static load testing. Hundreds of projects have been completed in Russia using this technology to value engineer drilled pile projects. In several instances, the number of drilled piles installed was fewer than half of the number originally planned for due to the capacity increase that EHDE-treated piles provided.Drilled PilesIn drilled pile construction, the EHDE process creates a mechanical pressure wave that impacts the base and sidewall of a drilled pile shaft. Soft, poorly consolidated or loose soil is compacted by successive pulses of pressure created by electrical discharges. These mechanical impulses are made by inserting a discharge probe into the wet concrete slurry. A discharge across the tip of the probe creates the pulse that travels outward to the sidewall and base of the drilled pile through the incompressible medium of the slurry. The power pack ratings for equipment presently in use are 35 and 50 kJ (kilojoule).Each pressure wave strikes the soil, causing compaction and expanding the hole. Workers apply the pulses until the size of the hole stops increasing. They watch the slurry level during pulsing. When the level quits dropping, further soil compaction in the drill hole sidewalls and base is not possible. After the pulse process is complete, workers insert a rebar cage and the pile is finished.The process does not alter the soil mineralogy. The electrical discharge is internally grounded and does not arc to the sidewalls of the drill hole. Soil is not scorched or altered in any manner; it is only compacted by the pressure wave. This technique has been used in urban areas with no effect on electrical or electronic equipment."

Jan 1, 2009

By Darren S. Diehm

"Construction for the restoration and expansion of 102-year-old Wrigley Field in Chicago, Illinois began at the conclusion of the 2014 baseball season. This six year project involves structural upgrades to the Stadium, improvements to the facade, infrastructure, restrooms, concourses, suites, press box, and bullpens, as well as the addition of restaurants, patio areas, batting tunnels, video boards, an adjacent Office-retail Tower and a new Hotel. The Bleachers were demolished and replaced, and a new underground Clubhouse was constructed for the Chicago Cubs beneath a new open-air Plaza. The 1060 Project is privately funded, projected at $750 million (US). The work will be completed in phases during consecutive off-seasons, each with a maximum 23-week duration extending through the Chicago winter. Ownership mandated that on-going construction cause no disruption to the Major League Baseball season, have no impact on hosting concerts and other special events, and it should not adversely affect seating capacity, or diminish the fan experience.The 1060 ProjectAfter purchasing the Chicago Cubs baseball team in 2009 from the Tribune Company, the Ricketts family began planning the renovation and improvement of Wrigley Field and its near neighborhood surroundings in Chicago, Illinois. What came to be known as the 1060 Project was officially announced at the annual Cubs Convention in 2013. Construction began on the $750M privately funded project in October 2014 at the conclusion of the Major League Baseball season. In their vision, the Ricketts committed the 1060 Project to three primary goals. First and foremost as a MLB franchise, the work should provide a meaningful contribution toward winning the World Series and ending the championship drought which stretched to the last win in 1908. Second, the project should be focused on preserving and improving Wrigley Field. Finally, the project should be committed to outcomes that enable the team to be a good neighbor and provide economic and social benefit to the local community.Constructed as Weeghman Park in 1914 for an estimated total cost of $250,000, the stadium provided seating for 18,000 fans and a home for the Chi-Feds and Whales of the National Federal League. The Chicago Cubs were enticed to move from the West Side Grounds in 1915. In the next 100 years, the Wrigley Field would be sliced apart and expanded, double its seating capacity with the addition of double deck grandstands, be enclosed by bleachers (and an ivy covered wall), and, in 1988, experience its first nighttime baseball game with the addition of lighting.The 1060 Project has a total budget of $750M, with an expected construction value of $350M. It is projected to add over 2,100 jobs to the economy and be completed before the 2020 baseball season. The work will be completed in phases during consecutive off-seasons, each with a maximum 23-week duration extending through the Chicago winter. Ownership mandated that on-going construction cause no disruption to the Major League Baseball season, have no impact on hosting concerts and other special events, and it should not adversely affect seating capacity, or diminish the fan experience."

Jan 1, 1900

By Brian McGlynn

There are many factors that can result in a site characterization being limited. For example, a client may undervalue the importance of a good geotechnical report, or an owner may feel that it would take too much time to perform an appropriate investigation among other reasons. For this project, neither was the case. The challenge was that the construction sequence of work required wick drains to accelerate the settlement of soil that had yet to be placed, resulting in the need to create a wick drain bid package based on unknown settlement parameters. This wick drain project took place in Long Beach, California, at the Long Beach Middle Harbor Re- development. For much of the past decade, the Port of Long Beach undertook a $1.5 billion redevelopment of two outdated terminals to create the Long Beach Container Terminal (LBCT). To achieve this goal, the existing terminals were demolished and the slip that serviced one of the older terminals was designed to be infilled to create the new area that would allow for the LBCT to manage 3.3 million TEUS (a commonly used freight term meaning twenty-foot equivalent unit) of cargo each year. Ultimately, the construction of the LBCT would be performed under multiple contracts to allow the new terminal to begin operation in a phased approach. Menard performed the wick drain installation under two out of three contracts, and this case history focuses on the challenges anticipated and faced under the second of these awarded contracts.

May 1, 2023

By Andy Boeckmann

Engineers and owners widely recognize the benefits of foundation reuse - cost savings, reduced construction schedules and reduced environmental impacts, among others. Yet for many projects with existing foundations identified as reusable, reuse is an idea that is discussed at length before cold feet prevail. To address this disconnect, Deep Foundations Institute (DFI) formed the Foundation Reuse Task Force in 2021, which intends to promote reuse, leveraging experience among DFI members and collaborating across pertinent committees. Indeed, the task force includes about 40 members drawn from the Subsurface Characterization for Deep Foundations, Sustainability and Testing and Evaluation committees. One of the first orders of business for the task force was to create a database of successful reuse projects, developing short summary documents highlighting the database projects and recruiting reuse-focused presentations for the ITS Money program. Solid progress has been made on each front: the case history database includes 12 cases so far; the first three summary documents were recently published to DFI's website and foundation reuse projects have been well represented among the past year's ITS Money program. The reuse case history summary documents are available at www.dfi.org/foundation-reuse- case-histories; each of the three is also discussed below. The summary documents demonstrate the feasibility and benefits of foundation reuse. The documents are therefore a useful tool for foundation engineers to share with owners, structural engineers and anyone else who may be hesitant to pursue foundation reuse. The task force continues to welcome new members and anyone interested in joining can contact Andy Boeckmann. The task force is also eager to highlight additional reuse success stories. Anyone with case history information to share is also encouraged to contact Boeckmann.

Jul 1, 2022

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By Howard Roscoe

Linking Ashford International Station to the new Channel Tunnel Rail Link required over 5000 rotary bored and CFA (continuous flight auger) piles to form tunnel walls and viaduct foundations and to support overbridges and trackside barriers.. Much of the work was carried out close to the existing railway infrastructure. Plunged columns were used to maintain traffic flows over the tunnel site during construction. The results of an extensive programme of vertical and lateral load tests on bored and CFA piles in heavily overconsolidated Weald Clay are compared to illustrate the relative importance of stress relief and of prolonged exposure to bentonite. The completion on schedule of this major piling and ground engineering contract (value £30 million) demonstrates that collaborative working in partnership produced cost effective solutions to a series of challenging technical and logistical problems.

Jan 1, 2002

By Timothy C. Siegel, Paul J. Axtell

The Missouri Department of Transportation (MoDOT) recently replaced the Hurricane Deck Bridge that carries Highway 5 traffic across the Osage Arm of the Lake of the Ozarks in Camden County, Missouri. The former bridge was constructed in the 1920's and was supported on pneumatic caissons bearing on dolostone bedrock. The replacement structure is founded on drilled shafts socketed into the bedrock. During the design phase of this bid-build project, a baseline design was developed and Alternative Technical Concepts (ATC's) were allowed from approved contractors. Those ATC's were confidential and not shared between teams. Either the baseline design or the approved ATC design could be bid by the respective contractors. The baseline design included re-use of the 90-year old caisson foundations. Accordingly, an extensive evaluation of the caissons and underlying bedrock were conducted by coring, laboratory testing, acoustic tele-viewer (ATV), and cross-hole sonic logging (CSL) methods. The results of the investigation indicated the caissons were in excellent condition and suitable for re-use. However, a more cost-effective ATC was submitted, awarded, and constructed that did not re-use the existing caisson foundations but rather reduced the span lengths, increased the number of piers in the water, and supported those piers on drilled shafts. Interestingly, the difference in low bid price between the awarded ATC and the baseline design was less than one percent of the construction cost. This paper describes the multiple foundation designs that were necessary for this interesting project. The various foundation evaluations include the existing pneumatic caissons, large-diameter open-ended pipe piles to support the baseline design, and the design of rock-socketed drilled shafts that were successfully constructed in 2012.

Jan 1, 2017

By Beim Jorge, Piscsalko George

"Verifying the quality of cast-in-place foundation applications, particularly those cast under slurry, is of course important, due to its great dependency on the methodology employed and on the practices of the site personnel. Due to the techniques used to install these elements, it is usually not possible to inspect the hole prior to grout or concrete placement, but there are several Non Destructive Test (NDT) methods available to assess the integrity of the completed foundation elements. This paper will compare several NDT methods with the Thermal Integrity Profiling (TIP) method for verifying the integrity in Continuous Flight Auger (CFA) piles and Bored Piles. The Thermal Integrity Profiling method will be described and some examples will be presented where TIP testing was used to confirm the structural integrity of CFA piles and Bored Piles.IntroductionThere are several Non Destructive Test (NDT) methods available for integrity testing of foundation elements. Each of those methods has advantages and disadvantages (White et al, 2008). Some methods test the integrity based on the reflections of a stress-wave generated by low or high-strain impact, while others require tubes to be installed prior to concrete pouring, and test the integrity between those tubes, or within a small proximity of them. The former methods (especially the low-strain) are faster and more cost-effective, but are not able to detect the quadrant where the damage is located. The latter methods are able to determine the quadrant, but do not test the region outside of the reinforcing cage, that is, they are not able to determine the concrete cover. The Thermal Integrity Profiling (TIP) NDT method overcomes the limitations of these other NDT methods.Overview of Shaft Integrity MethodsUntil now, the most widely used methods to test the integrity of Bored and CFA piles were the low-strain pile integrity testing and the cross-hole ultra-sonic testing. The low-strain method for integrity testing (PIT) involves attaching an accelerometer usually to the pile top (using a putty or wax) and striking the pile surface with a handheld hammer, which causes a compressive wave to enter the pile. This wave is totally reflected when it reaches the end of the pile or a major defect, and is partially reflected when it encounters any change in crosssection, or a change in the resistance or density of the pile material. These reflections arrive at the top at a time determined by the distance and wave speed, and causes a noticeable change in the signal detected by the accelerometer. The acceleration signal is normally converted to velocity by simple integration, and sometimes the force applied by the hammer is also measured. The velocity (and force) signals can be processed by the pulse-echo method (in the time domain) or by the transient response method (in the frequency domain)."

Jan 1, 2015