Search Documents

By K. [Muthukkumaran

An extensive program of laboratory model tests was undertaken to study the effect of slope on p-y curves under passive loading in dry sand. The paper concerns the method developed in a series of laboratory model tests to experimentally determine p-y curves. Bending moment curves are differentiated by using curve fitting method of cubic polynomial function. The study includes effect of slope angle and relative density on bending moment and non-dimensional p-y curves. The non-dimensional p-y curves for piles on sloping ground under passive load are developed modifying API method by including a Reduction Factor (R) using the experimental results.

Jan 1, 2006

AUSTRALIA CHAPMAN Gary JOHN WAGSTAFF CONTSRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE BRISBANE HILLAR Jaaes Director J.A. HILLAR & ASSOCIATES 99 Woolwich Road WOOLWICH, NSW 2110 WAGSTAFF John Managing Director JOHN WAGSTAFF CONSTRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE, BRISBANE AUSTRIA FUCHSBERGER M. TECHNISCHE UNIVERSITAT INSTITUT FUR BODENMECHANIK Rechbauerstrasse 12 8010 GRAZ

Jan 1, 1994

By [D. N. ] Naresh

During different activities pile installation like pile boring, concreting etc., it is likely that various problems, depending up on site condition may be encountered. There are possibilities that some of the activities if not correctly followed may affect the pile capacity. This paper describes few problems encountered during pile execution at different sites and presents the remedial measures undertaken to overcome them.

Jan 1, 1996

By J. L. Goen

The Saint Joseph Hospital of Bellingham is located on a site underlain by glacial outwash. The construction of a five-story tower addition above an existing two-story wing was supported by five large trusses that impose a 1600 kips (7117 kN) column load on five pile caps in the courtyard of the hospital and on the new pile caps inside the existing MRI laboratory. The exterior columns of the trusses and the new parking garage addition were supported on conventional auger cast piles installed with conventional equipment. Helical Pulldown® micropiles were selected for use in the courtyard and the MRI laboratory because lightweight installation equipment (maximum unit weight of 7.5 kips (33.3 kN)) had to be used and it was required that no spoils be produced. The installation equipment was lifted into the courtyard by the jobsite crane. Sixty Helical Pulldown micropiles were installed for the pile caps in the courtyard. The pile caps inside the hospital were supported on 240 Helical Pulldown micropiles. Initial compression test indicated an allowable load for the micropiles to be 55 kips (244 kN). However, retest at a later date resulted in an increased allowed design load to be 85 kips (378kN) reducing the number of micropiles required by more than fifteen percent.

Jan 1, 2004

By Alan Alhadeff

Why is mediation being hailed as the wave of the future? The high cost of putting on a trial, over-crowded court calendars and long trial delays have resulted in what prominent attorneys and leading jurists are calling a litigation crisis. In no segment of the legal world are these pressures greater felt than in the trial of the serious construction case. Furthermore, the siege mentality of both the plaintiff and defense bar often leads to a reluctance by either side to make the first reasonable offer for fear of showing weakness. Attorneys operating in the serious construction case arena express concerns that there exist insufficient opportunities for the parties to meet, tell their stories, and negotiate settlement prior to the eve of trial. Mediation, by opening lines of effective communication and encouraging meaningful settlement negotiation, has proven to be a very effective antidote to the litigation crisis.

Jan 1, 1990

By Lok M. Sharma

Development of brownfields is of great interest in these days. Such fields are not easily adaptable for foundations of structures. The uncertainties in ground behavior present challenges of unpredictable subsidence that could be detrimental to the build up facility. A desalination plant had to be located along the seashore, close to the needy population and the existing water supply infrastructure. The available site had been developed as a recreational park area over a dumped construction demolition debris landfill along the coastline. To construct a desalination plant comprised primarily of large concrete basin tanks on slab, founded on the debris fill had its challenges. A ground improvement system in the form of vibro replacement stone columns was designed and constructed. Approximately 5,000 stone columns were installed across the site. This paper describes the analysis process, the design, field load testing, and installation of stone columns. Difficulties during construction and monitoring aspects are briefly described. The plant started operations in the summer of 2008 and to date has performed satisfactorily. When properly designed, the development of brownfields is achievable at other sites.

Jan 1, 2009

By Terence P. Holman

Micropiles are employed to retrofit existing foundations, including underpinning prior to future construction operations and resupport of existing structures that have experienced distortion and settlement. This paper presents analyses of the two case histories requiring the use of micropiles in these applications. The first case history involves micropiles used to resupport a settled pump station next to an excavation which had suffered basal failure and ground loss. A compression load test pile experienced plunging failure which, after analysis of the strain-gauge data acquired during the test, was attributable to a greater degree of disturbance to the subsoils beneath the site than anticipated. After construction of the micropiles around the pump chamber a synchronized jacking system was used to lift and right the 320 kip chamber structure, followed by resupporting it on the newly constructed piles. The second case history entails the use of micropiles for direct underpinning support of existing columns prior to a utility tunnel installation within an existing high-bay warehouse structure. The design constraint that most significantly affected the successful completion of this project was the desire to bond the new piles into the existing reinforced concrete foundations. As a result of the coring method through the footing, the ultimate bond stress measured during a pullout test was more than twice that assumed in the design. Monitoring of the underpinned columns during trench excavation indicated that the system performance was acceptable. These case histories reinforce the concept that lower capacity micropiles can provide a rapid means to underpin and retrofit existing structures.

Jan 1, 2007

By Michael P. Balducci

Urban deep foundation projects contain unique risks that must be recognized by the parties involved. Common pitfalls must be recognized and avoided or addressed through contractual relations and corresponding insurance coverage. By understanding these pitfalls, examining the risk-apportioning clauses and corresponding insurance obligations, may the parties? desires and expectations be met.

Jan 1, 2008

By Debra F. Laefer

Jet grouting is a ground improvement technique that has become widely adopted over the past three decades, yet relatively little data has been published about performance characteristics of mixes under adverse conditions, such as the inclusion of clay lenses. This paper presents an experimental investigation on the impact of clay on the strength of jet grouting. A total of 150 grout samples were subjected to 0-10% levels of Kaolinite and Bentonite inclusion. While the Bentonite was introduced as a pre-hydrated slurry, the Kaolinite was mixed in two ways: in a pulverized condition and as large chunks. Sample strength and stiffness were measured at multiple dates within the first 28 days. With 10% clay inclusion all samples exhibited significant strength and stiffness losses. With some, substantial losses began with as little as 4% clay. Even a 1% clay inclusion tended to decrease strength and stiffness between one-quarter and one-third of the control sample. Depending upon clay type and inclusion method, results differed significantly with respect to strength and stiffness development and failure mechanism. Petrographic analysis is used to provide further insights as to apparently divergent behaviors.

Jan 1, 2009

By Pierre Gouvin

This paper describes the design, installation and monitoring of a state of the art real time geotechnical/structural instrumentation monitoring system to facilitate tunnel construction under Interstate route I-5 in Seattle, Washington, USA. The project involved removal of existing highway foundation substructures on both North and Southbound lanes as well as the underground reversible high occupancy vehicle lanes. The system utilized state of the art 3-D pulsed laser scanning, wireless sensor networks, automated robotic total stations, tilt beam sensors, narrow angle tiltmeters, and in-place inclinometers. Dedicated real time data loggers, with a web based graphical interface, provided 24/7 access to critical measurements. In addition to the instrumented sections of wall and roadway subsurface which monitored physical measurements at known points, the pulsed laser scanning allowed complete site monitoring coverage where physical sensors were not located. This data allowed post processing at any location enabling the contractor and designer to respond to unforeseen structural responses to construction. Use of the instrumentation system resulted in the early detection of wall movement, and provided feedback to the designers to facilitate construction process changes in order to minimize further movement.

Jan 1, 2010

By John G. DiGenova

The Allwell Center Ice Arena at Plymouth State University, Plymouth, New Hampshire is located in the flood plain of the Pemigewasset River. To maintain the arena near the level of the surrounding area, foundation design required use of uplift elements to resist hydrostatic loads caused by frequent flood conditions. Soils beneath the arena consisted of very loose to medium dense alluvial deposits overlying thick glaciolacustrine deposits. Bedrock was encountered at depths of 115 feet (35 m) or more. A mat foundation with a sealed building system was developed for the arena to guard against flood events. Several alternatives were investigated to provide uplift capacity for the mat foundation, including the Rammed Aggregate Pier® (RAP) system, driven precast-prestressed concrete piles, driven H-piles, and deep drilled soil/rock anchors. Evaluations indicated that the most cost effective uplift solution was a tension RAP system that developed uplift resistance in the shallow alluvial deposits. A total of 344 55-kip (245-kN) capacity RAP elements were required for the project. The RAPs were designed to resist tensile loads using threaded steel bars. Dual corrosion resistance was provided to the uplift elements by including sacrificial steel and galvanizing the oversized bars and connection plates. A pre-construction test program was conducted on RAP elements drilled to a depth of approximately 25 feet (7.6 m) and installed using various shaft construction procedures and materials. Ten test piers were constructed and six were tested to verify that the piers could resist 200 percent of the design load with measured deflections of less than 1 inch (25 mm). The RAP system also provided improved bearing conditions for the perimeter wall and mat foundations by densifying and stiffening the upper alluvial soils.

Jan 1, 2011

By Aly M. Mohammad

Croton Point Avenue Bridge carries Croton Avenue over Metro-North main tracks at Harmon Rail Yard in Westchester County, New York. The new bridge is 1100 foot long and 36 foot wide nine span structure with three spans continuous units. The spans are steel multi-stringers, composite with concrete deck. The piers are solid wall piers and the foundations are spread footings. During the design of the bridge foundations it was determined that the relatively loose to medium dense sand layer is susceptible to liquefaction under a design earthquake with a seismic coefficient of 0.15g. Several foundation options were considered for the new bridge including both shallow and deep foundations. It was determined that the most cost effective alternative is to use spread footing foundations supported on densified soils. Vibratory probes were utilized to densify the loose to medium dense sand layer and reduce the risk of liquefaction. Densification test sections were performed to determine the optimum spacing for the vibro probes. The test sections included performing piezocone tests before and after the densification to compare the increase in relative density of the sand. In addition, ground surface settlement due to the vibro probes was measured and correlated to the increase of soil relative density. The paper will present the results of the ground improvement method utilized and correlate the spacing of the vibro probes and the increase in relative density and the results of the piezocone tests performed before and after the densification. It was found that the vibro probes are not as effective as thought at shallow depth below the ground surface. It is believed that the results and finding presented in this paper will benefit both the design and construction industries by providing a relatively cost effective means to improve the soils

Jan 1, 2007

By Edwin W. Hickey

This paper briefly discusses the geologic conditions in South Florida relative to the design, construction, and performance of deep foundations. The subsurface conditions in this area are unique in that the rock layers are highly porous and often very soft, and are sandwiched between layers of typically loose, uncemented quartz fine sands. Due to the high porosity of the Miami Limestone, 4-inch diameter rock coring is often required to obtain intact samples, and dewatering of excavations is sometimes difficult or impossible. The sand layers, typically tens of feet thick, are very loose to loose in relative density and have been the cause of unexpected large, deep foundation settlements. The engineering properties of the various geologic formations are discussed, along with typical deep foundation types used in the Miami area prior to and after 1980.

Jan 1, 2003

By Jon E. Bischoff

Construction of a secondary clarifier on the banks of Rainy River, Northern Minnesota, required the driving of H-piles 14HP102 to a sloping, very strong bedrock through thick deposits of soft and medium stiff soils. Pile toe protection, APF Hardbite HP 77750, was specified to prevent damage to the pile toe and to enable the pile toe to bite into the bedrock surface. The toe protection worked well for bedrock sloping less than 2H:1V. However, where the bedrock was steeper, the piles experienced damage and failed to reach bearing. In most cases, the also the replacement pile failed. Pile Driving Analyzer measurements showed that on encountering the bedrock, the pile toe reflection, which at first was sound, deteriorated indicating pile toe damage. Extraction for visual inspection showed that the failed piles were bent and had deformed pile shoes. In areas of steeply sloping bedrock and for replacement piles, an alternative shoe, the Scanpile Herkules rock shoe, was employed. This pile shoe proved to be able to secure the pile toe into the rock and to eliminate the problem. The costs of the Herkules rock shoe considering price, shipping, and attaching, were about equal with the Hardbite shoe.

Jan 1, 1993

By Richard E. Sylwester

Evaluating surface and subsurface conditions for marine foundations (bridges, causeways, terminals, etc.) is often done with a limited amount of data. Subsurface information for these projects is primarily acquired using traditional methods, such as boreholes, test pits or divers, which tend to be expensive and limited in the area of coverage. A number of geophysical methods, including precision bathymetry, sidescan sonar, and seismic reflection or subbottom profiling are extremely cost-effective and obtain significantly more data than can be acquired using traditional intrusive methods. These geophysical methods provide detailed surface images and continuous profiles of the subsurface stratigraphy. This information can be invaluable for selecting the best location for geotechnical boreholes and to map potential geohazards such as submarine slides and filled or open scour holes. Offshore investigations conducted for a proposed highway bridge (Knik Arm Bridge, Cook Inlet, AK), the retrofit of two existing bridge (Antioch and Dumbarton Bridges, CA) and a proposed cruise ship terminal (Ketchikan, AK) used a combination of geophysical methods to map water depth, detect and map debris on the seabed, map the thickness of unconsolidated sediment, determine the depth to bedrock and identify potential geohazards such as scour holes. The results of the geophysical investigations will be used to select locations for obtaining geotechnical borings, to extrapolate geologic information between existing or proposed boreholes, evaluate the potential depth of scour and design a pile support pier. Geotechnical engineers, offshore contractors and bridge designers are realizing the importance of the early use of offshore geophysics for (i) site characterization, (ii) to reduce the uncertainty of geotechnical conditions thus avoiding designs that may be overly conservative and thus more expensive and (iii) to assist in selecting locations for geotechnical borings.

Jan 1, 2013

By Franz-Werner Gerressen

In the changing construction environment clients are searching for new technology to complete their projects in shorter times. Manufacturers are therefore developing solutions to speed up established construction methods. The significant progress in recent years with the development of increasingly powerful drilling rigs is providing piling companies increase options for the execution of specialist foundation projects. The double rotary drilling methods are primarily used for the construction of pile walls as support for deep excavations. Typically these retaining walls are designed and installed as cased piles using the established Kelly drilling mode. However, more recently it is more popular to undertake these projects with the Cased Continuous Flight Auger (CCFA) system. This paper provides an overview of drilling with double rotary methods, in particular the monitoring during installation.

Jan 1, 2009

By G. Ranjan

The designers and the practicing engineers have started using latest and cost effective techniques of ground improvements which utilise the weak and poor sub-soil deposits efficiently for the civil engineering construction. In the present investigation, a new concept of 'skirted granular piles' has been advocated. An effective method of construction of granular piles as an economical alternative to vibroflot, and the skirt has been developed. The construction technique is based on indigeneous know how which effectively utilises the man-power technology avoiding import of costly equipment suiting to the developing countries. Full scale insitu tests have been carried out at four sites, having different soil conditions, on virgin weak sub-soil, and improved ground by casting plain and skirted granular piles. Effectiveness of different types of skirt has been demonstrated through insitu tests. A simple analytical approach has been proposed to predict the ultimate pile capacity. The predicted values of ultimate capacity have been found to demonstrate a good correspondance. Granular pile behaviour in terms of pile depth, diameter, spacing and stress deformation characteristics of the improved ground have been discussed. A significant improvement in ultimate capacity in improved ground has been noted. This is further augmented when granular pile group is skirted.

Jan 1, 2010

By Peter de Kort

Tunnels in urban areas generally require deep excavations in soils under the groundwater table. In The Netherlands uplift loads are generally taken by piles installed into dense sand layers, which are hard to penetrate. To avoid nuisance and damage to the environment, piles often need to be installed using vibration free methods, which also have the advantage of low noise levels during installation. Drilling piles and obtaining a high uplift resistance is a contradiction in itself. Franki has adopted several installation methods based on the injection of grout during drilling and/or post grouting to overcome the difficulty of hard layers. This report presents two projects, situated in Rotterdam and Sneek, where vertical tension piles in floors, subject to high uplift loads, have been used. It also explores a project in Zeebrugge (Belgium), where tension piles are installed at an inclination of 1:1 to anchor a diaphragm wall for a quay construction. Test results presented in this report show, that vibration free and soil displacing piles can be installed in very dense sand layers and that a high uplift resistance can be achieved. It is also shown, that a variety of installation methods is available, even in limited space.

Jan 1, 2008

By Jesús E. Gómez

A total of 260 micropiles were installed as part of a retrofit effort for two existing bridges. The micropiles consisted of hollow core bars installed under limited headroom conditions. Of the total number of micropiles, 180 were installed in submerged sand and 80 were installed in stiff, silty clay. The micropiles were drilled using a lean cement grout which was re-circulated for de-sanding and re-use. Final grout was injected upon completion of drilling to the design tip elevation. The micropiles were subject to a rigorous quality control that included grout quality testing and proof-testing of each production micropile. This paper presents a description of the procedure for installation and quality control of the micropiles. The successful proof-testing of all the production micropiles showed that hollow core bar micropiles can be used effectively in granular and fine-grained soils. Hollow core bar micropiles offer particular advantages when installed in submerged sand formations with respect to other traditional micropile types. The results of the proof load tests are presented in a companion paper.

Jan 1, 2007

By Jeffrey R. Hill

This paper discusses the use of micropiles for the rehabilitation of the following two structures: the Milwaukee Auditorium Theatre, in Milwaukee, Wisconsin, and the Cupples Ballpark Lofts, in St. Louis, Missouri. The paper focuses on the similarities and differences of the remediation techniques used for each structure. The discussion highlights the method of attaching the micropiles to each respective structure. Generally the paper discusses the micropile installation at each project with supporting photos, figures and data. Load testing at each project is also discussed, including the comparison of load test results for each project. The paper will focus on the load testing program at the Milwaukee Auditorium Theatre where high capacity micropiles were designed and tested as friction piles founded in stiff clays and end bearing micropiles in dolomitic limestone. The results of the test were used to determine if the micropiles on the project would be installed as end bearing or friction bearing elements. Strain gauges were used in addition to conventional deflection vs. load data for the Milwaukee Auditorium Theatre project. Other aspects of the paper will include the differences in design methodology for end bearing micropiles in massive dolomitic limestone vs. design in softer, weathered limestone.

Jan 1, 2008