Search Documents

By Alice Arana, David M. Cacoilo, Joel L. Volterra

"To make space for the new South Ferry Station in lower Manhattan, engineers and contractors carved out a new tunnel beneath three operating subway tunnels and tangentially to yet another tunnel. Creating the space required the design and construction of complex temporary excavation support and underpinning systems and the design and installation of real-time monitoring systems. Construction for the new station and tunnel was mainly cut-and cover in a mixed-face area of soil and rock approximately 2,000 linear ft long, 60 ft wide and up to 70 ft deep. Close coordination between the design/build team and the project owner, the Metropolitan Transportation Authority (MTA), was critical.With the construction of this $400 million project, the MTA and New York City Transit (NYCT) are correcting the numerous physical and operational deficiencies of the existing station and improving the lives of millions of commuters. Built in 1905, the original South Ferry Station is on the IRT Broadway–Seventh Avenue Line of the New York City Subway and is the southern terminal of the #1 subway service, which forms a loop to return uptown. The station has a sharply curved single platform on the outside of the outer track of a two track loop. This platform is short and does not allow the rear five cars of a normal 10-car subway train to load or unload. In addition, once the train stops at the station, commuters wait while retractable floor grates bridge the gap created between the platform and the subway car doors, and then they have only one exit from the station. Spray nozzles keep the tracks lubricated to reduce the train wheels’ friction caused by the tight curve. The sharp curvature of the loop and the inability to use half of the subway car doors slow train operation. With the new ADA-accessible station, 10-car trains will be able to open all doors, and additional entrances, escalators and elevators will greatly reduce travel times."

Jan 1, 2008

By Yahia M. Al-Smadi

Effect of lateral loading against existing sheet pile wall and distribution of gravity loading due to various number of construction loading scenarios were studied. The objective of this effort was to determine the loading case that permits the contractor to utilize a 400 ton crane at the specified location with the existing limitation imposed on site. Staged analysis was determined as the methodology that will more accurately predict the exiting and additional stress due to the impose crane loading. A reliable and robust analysis (ANSYS) software was used to complete both 2D and 3D finite element model and analysis. Analysis model parameters such as material properties, non-linear behavior of the soil, and meshing are presented and discussed. At the conclusion specific range of crane operation and pick weights operating on existing concrete mat supported on top of an existing tunnel was reviewed and deemed acceptable.

Jan 1, 2010

By Evangelia Ieronymaki

Civil engineering education relies on traditional methods of teaching, comprising mostly of deductive instruction by presenting the theory, followed by applications. This paper presents an alternative way for teaching foundation design to senior students, introducing a more inductive approach. The students are presented with a project/game adapted to a real-world problem at the beginning of the course. They are asked to identify the correct steps and methods throughout the lectures, for reaching an appropriate solution that they document and present at the end of the course. To make the project more enjoyable, the project has the format of a game where the students compete with each other on completing the task faster and more efficiently. The goal of this teaching approach is to enhance the ability of the students for problem solving and the engineering way of thinking, while playing a game. In the end, the students were requested to respond to a survey regarding the efficiency of this project/game on their learning. The results showed that students prefer more inductive methods for a design course, feeling that this project made them think more like engineers, while the ‘game’ twist of it made the whole course more fun. INTRODUCTION Most civil engineering courses are taught in 2019 the same way they used to be taught 40 years ago in the 80s. Classic methods are mostly deductive, where the instructor presents the theory first and then applications of that theory follow. Little or no attention is given initially to why the theory was developed or what are the problems it solves. The applications of the theory, and thus the purpose it serves, come only in the end and after methodologies have been presented, leading the students to show low interest in the material. As Albanese and Mitchell (1993) have reported, people are mostly motivated to learn things when they clearly see the need to know them. This explains the students’ little motivation that, if any, comes mainly from the fact that the material may be useful either in other courses or in their future careers. On the other hand, there are alternative inductive methods of teaching, where the role of the students is more active. A lot of researchers have highlighted the benefits of inductive methods in teaching engineering courses. Based on Prince and Fedler (2006), inductive methods include; a) inquiry-learning, b) discovery learning, c) problem and project-based learning (PBL), d) case-based teaching, and e) just-in-time learning. Inquiry-learning is maybe the most traditional method of inductive teaching/learning methods, where the instructor asks questions or poses problems and the students need to apply the theory they have learnt in order to find the solution (Bateman 1990; Prince 2004; Lee 2012). Similar to inquire-learning is the discovery learning, where students have to find the solution to a problem or answer to a question, while the instructor simply provides feedback to the students without guiding their efforts (Leonard 1988; Westbrook and Rogers 1994).

Jan 1, 2019

By Peter Faust

The foundations for the new South Viaduct Bridge in San Francisco were extremely challenging due to the requirement for very large and deep piles installed adjacent to historic structures. Drilled shafts up to 12? foot in diameter were constructed to a maximum depth of 200? feet in alluvial soils and Franciscan Bedrock using an oscillator system for the installation of the permanent steel casing. This paper provides an overview of the construction techniques, the equipment, and the challenges associated with constructing 12? foot diameter shafts on this very complex project in one of the nation?s nicest landscape setting.

Jan 1, 2011

By Edward C. Clukey

A deep mixing method (DMM) foundation was selected by the Project Team for a very largeLNG facility in West Africa. As described in a companion paper, this foundation consists of alarge number of columns installed by mixing cement with in-situ soils. The foundations arearrayed as a variety of honeycombed type configurations which, if installed to desiredspecifications, can provide a robust foundation alternative. The foundation is capable ofdistributing loads and limiting settlements even if some of the soil in the columns is not fullymixed during installation. An important part of the overall quality assessment program,therefore, involved developing a testing program to verify the methodology. In addition theimpact of potential defects in columns on the overall foundation integrity had to be assessed.This paper describes some of the preliminary work done to establish the requirements for thequality assurance program. A key component of this program involved the samplingfrequency used to assess potential defects in the columns. To verify the column integrity 104-mm samples were taken continuously at a selected frequency through the 23 m longcolumns. The preliminary work described in this paper demonstrated that the appropriatesampling frequency depends on both the desired reliability level as well as the number ofdefective columns encountered during testing. Initial finite element analyses were performed to assess the extent that defects could occur incolumns within the honeycombed structure without adversely affecting the overall foundationintegrity. The results from this work demonstrated that the spatial location of the defects wascritical to properly assessing the foundation integrity. In addition to column sampling a load test was performed as part of the foundationverification process. The methods used to apply appropriate loads so that loads at thebottom of the columns approached design values are discussed in the paper. The results obtained from this preliminary study were then used to help develop a morecomprehensive assessment program, described in a companion paper, to determine therobustness of the DMM foundations for both the LNG processing facilities and a condensatetank.

By Patrick E. Durnal

A joint venture of Ben C. Gerwick Inc., Sverdrup (now Jacobs) and DMJM (now DMJM Harris) designed the $779 mill seismic upgrade of the Richmond - San Rafael Bridge over the San Pablo Bay in the San Francisco Bay Area and provided construction support to Caltrans. Construction of the marine foundation retrofit was completed by a joint venture of Tudor Saliba/Tidewater/Koch-Skanska and their subcontractors: Pomeroy Precast Construction, AGRA Foundations, Dutra Construction and Vortex Divers. Construction management and inspection was performed by Caltrans with support of various consultants.

Jan 1, 2013

By Filippo Maria Leoni, Wesley Schmutzler

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 90 inch forced sewer main relocation and to improve the soils for the base of a new drainage channel. The project is located just east of San Juan and south of the Horizon Port. The soils to be improved consisted of fill, marine clay, organics (peat) and the foundation clay layer. A preconstruction soil investigation campaign was performed to assess soil properties and to retrieve samples of the different soil layers for the laboratory Bench Scale Testing program (BST). The BST was conducted using various binder contents and water/cement ratios in each of the soil types; the selection of the different combinations and dosages was based on past extensive experiences on similar materials. Following the laboratory program, a full scale Field Test (FT) was done installing several DMM elements to verify the results of the BST and fine tune the construction parameters. Each element consisted of two 5.5 feet diameter overlapping mixing augers installed simultaneously to a depth of approximately 60 feet using a SOILMEC SR-90 dual axis drilling rig. The FT construction and post-construction coring results showed significant differences between the lab study and the actual field conditions. This paper will highlight these differences and the importance of performing both pre-construction laboratory and field tests in order to ascertain the proper mixing parameters in the different soil layers.IntroductionThe Puerto Nuevo project consists of the stabilization of a major drainage channel using Deep Mixing Method (DMM) and the relocation of a 90 inch forced main sanitary sewer outfall. The first portion of this project was a 40 x 16 x 2,000 foot box culvert installed in 2004. In order for the drainage system to be completed and function properly, the 90 inch forced main needed to be lowered about 20 feet to allow for proper drainage.DMM was chosen by the US Army corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The overall layout of the project is shown in Figure 1. The DMM is arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for ZONE A and B as an example. (Figure 2) The total amount of soils to be treated by DMM is approximately 84,000 cubic yards up to a maximum depth of 57 feet from ground surface and an Area Replacement Ratio of 100%.The equipment used to perform the DMM is a Soilmec SR90 twin-shaft jet assisted deep mixing rig (Figure 3) coupled with a LODOS 30 grout plant and two Soilmec 7T-500J high pressure pumps."

Jan 1, 2015

By James P. Hambleton, Anastasia Nally

This work focuses on the numerical simulation of multi-plate anchor systems (e.g., helical anchors) in sand subjected to vertical loading. In assessing the stiffness and capacity of these multi-plate anchor systems, full awareness of the abilities and limitations of the various analysis methods must be understood. This work first summarizes studies completed by others and then goes on to assess the failure mechanisms of multi-plate anchors in sand and the influence of (1) plate width-to-depth ratio, (2) number of plates, and (3) relative positioning of plates. The analysis makes use of (1) conventional limit analysis, (2) so-called modified limit analysis that employs reduced strength parameters to account for the influence of soil dilatancy, and (3) the displacement-based finite element method, which considers elastic as well as plastic deformation leading to failure. The work critically reflects on limitations in the current analysis methods for helical ground anchors. INTRODUCTION Helical anchors are a relatively low cost foundation type, typically consisting of a steel rod and single or multiple plate attachments. In recent decades, they have seen rapid growth, and as outlined by Merifield and Sloan (2006) and Hambleton et al. (2014). Design techniques for helical anchors have previously been predominately empirical, as much of the past research in this field is experimentally based. It is common practice for helical anchors to be modeled as horizontally oriented plate anchors in both numerical and experimental analysis. This work focuses on analysis based on the finite element method, including so-called finite element limit analysis and the conventional displacement-based finite element method, with some comparisons made to experimental studies. Numerical simulation of anchor pull-out capacity in cohesionless soils is stunted by the many difficulties faced when using numerical analysis with cohesionless soils. Additional variations can be seen when comparing the serviceability based load capacities to the ultimate load. In this work, both the force-displacement response (stiffness) and the ultimate anchor capacity are assessed, with more focus on the latter. This work focuses only on analysis techniques for multi-plate anchors with vertical loading in cohesionless soils. Many studies have been completed in this area, some of which assume a rectangular plate in a plain strain model (Rowe & Davis, 1982; Merifield & Sloan, 2006; Cerfontaine et al., 2019). Whereas others use axisymmetric conditions (Baker and Kondner, 1966; Saeedy, 1987; Murray & Geddes, 1987; Ghaly & Hanna, 1994; Sakai & Tanaka, 1998; Merifield et al., 2006;) and minimal studies considered both axisymmetric and plane strain in the one study (Vesic, 1971; Tagaya et al., 1988; Murray & Geddes, 1987; Sarac, 1989).

Jan 1, 2019

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Attasit Korchaiyapruk, Edward C. Clukey

"A deep mixing method (DMM) foundation was selected by the Project Team for a very large LNG facility in West Africa. As described in a companion paper, this foundation consists of a large number of columns installed by mixing cement with in-situ soils. The foundations are arrayed as a variety of honeycombed type configurations which, if installed to desired specifications, can provide a robust foundation alternative. The foundation is capable of distributing loads and limiting settlements even if some of the soil in the columns is not fully mixed during installation. An important part of the overall quality assessment program, therefore, involved developing a testing program to verify the methodology. In addition the impact of potential defects in columns on the overall foundation integrity had to be assessed. This paper describes some of the preliminary work done to establish the requirements for the quality assurance program. A key component of this program involved the sampling frequency used to assess potential defects in the columns. To verify the column integrity 104- mm samples were taken continuously at a selected frequency through the 23 m long columns. The preliminary work described in this paper demonstrated that the appropriate sampling frequency depends on both the desired reliability level as well as the number of defective columns encountered during testing.Initial finite element analyses were performed to assess the extent that defects could occur in columns within the honeycombed structure without adversely affecting the overall foundation integrity. The results from this work demonstrated that the spatial location of the defects was critical to properly assessing the foundation integrity.In addition to column sampling a load test was performed as part of the foundation verification process. The methods used to apply appropriate loads so that loads at the bottom of the columns approached design values are discussed in the paper.The results obtained from this preliminary study were then used to help develop a more comprehensive assessment program, described in a companion paper, to determine the robustness of the DMM foundations for both the LNG processing facilities and a condensate tank.IntroductionFoundations constructed with the Deep Mixing Method (DMM) can be an attractive and cost efficient alternate to other deep foundation options. This foundation is constructed by mixing soil and cement with an auger type drill. The foundation is usually constructed with a dual auger system that simultaneously creates two contiguous columns called foundation elements. Many elements are then arranged in a honeycombed configuration to create the overall foundation (Figure 1). A desired column strength can be obtained by varying the volume of cement added to the columns, the mixing rate of the soil and stroking sequence."

Jan 1, 2017

By Lynn Crayne

We used Glyoxal as the hardener, at a final concentration of 10% by volume and therefore 20% by volume in the A-Component. They worked pretty well what we did was we shaved the joints on each of the pipes when we assembled them so they wouldn't rip the packers and then we greased the packers very well going in. We had to replace some but we have any getting stuck or didn't lose any pipes.

Feb 10, 2003

By Jörn M. Seitz

Dynamic load testing is employed with ever increasing frequency to estimate the strength and elastic settlement behavior of piles of all types. For dynamic loading ram masses up to 20 Mg have been used and pile resistance forces up to 30 MN have been activated. Strains and accelerations induced by the impact are measured near the pile top and a load-set curve is computed by the so-called CAPWAP method. This paper briefly describes both the necessary equipment and other details of the dynamic tests and the available analytical tools for data interpretation. Furthermore the need for further research and the current status of standardization will be discussed. This paper also presents the results from several static and dynamic correlation tests on cast-in-situ piles of up to 2 m diameter and 64 m length. The results demonstrate the economical and technical feasibility of this test method.

Jan 1, 1987

By Douglas R. Hardin, Stanley L. Worst, Joanna Mason

A challenging earth retention project presented itself in Washington, DC in the backyard of the historic House of the Temple (The Scottish Rite of Freemasonry, Supreme Council 33°). Located at 15th St NW and S St NW, a forty-foot-deep underground basement was to be installed adjacent to the existing Temple, a historic Carriage House structure dating back to the 1800’s and across a narrow alley from a four-story brick apartment building. The unique geology of the site included typical urban fill overlying a mixture of loose alluvial soils underlaid by dense marine deposits of the Potomac Formation. The clay, sand and gravel of the Potomac included nested boulders up to three feet in diameter. Design of the earth retention system accounted for ground conditions, installation methods and estimated movement of the system and adjacent structures. Anticipated ground water and unanticipated water from leaky sewers also proved obstacles to overcome during construction. Soldier beams were installed using a variable momentvibratory hammer to minimize disturbance to the historic and sensitive structures. Monitoring of the existing structures included both seismograph and optical targets during installation of soldier beams and as the excavation progressed. Micropiles drilled into the Potomac Formation were a part of the permanent foundation for the new structure. This local case history will delve into the details of the successful design, installation, and performance of an earth retention system and micropiles in a historic and highly congested urban environment.

Oct 1, 2022

By Michael Quadagno

Hudson River Pier 86, home of the historic USS Intrepid Aircraft Carrier and the Intrepid Sea-Air-Space Museum, is currently undergoing a $30M reconstruction. This project involves the demolition of the old timber pile supported pier and construction of a new 150 ft wide by 782 ft long concrete pier, built over the footprint of the old piles. The new pier consists of steel pipe piles, precast concrete pile caps, and a composite deck, made up of precast, prestressed concrete planks and cast-in-place concrete topping. This paper focuses on both the structural design and construction of the new pier, with emphasis on the pile foundation. Pier 86 is unique in that it is required to resist the extremely high lateral loads imposed on it by the permanently moored 898 ft long aircraft carrier during severe storms. A total of 360 steel pipe piles support the new pier. These piles, which are 24 in. in diameter and range in length from 58 ft to 175 ft, were driven down to bedrock. The piles, each having 200 ton allowable capacities, work together to resist the significantly large lateral loads exerted on the pier by the ship. The installation of the piles was unique in that all the piles, including the ?super-longs?, were fabricated to-length offsite, delivered to the site via truck and barge, and installed in one piece, eliminating the need for field splicing. The Pier 86 reconstruction will be completed within an extremely aggressive 18 month schedule, from January 2007 through June 2008. The refurbished aircraft carrier Intrepid will return home in September 2008, and the grand re-opening of the pier will be on Veteran?s Day 2008. This paper provides a case history for owners, government agencies, engineers, and construction professionals that will be faced with the challenges of designing and building new piers.

Jan 1, 2008

By Chandrasegaran, Tamilmani

"This paper describes a case study of a retaining wall structure using a diaphragm wall to construct a stilling basin at Tanjung Bin T4 power plant in Johor Bahru, Malaysia. The stilling basin is part of the Phase IV (T4) 1x1000MW power plant’s offshore cooling water discharge culverts. The site is located close to the sea with 5m of fill on top of very soft sediments of marine origin up to 20m thick underlain by fluvial clay and metasedimentary rock. Stringent wall deflection criteria and construction program dictated adopting an efficient solution with 800mm thick diaphragm wall supported by permanent top support as the temporary prop and improved horizontal restraint provided by deep mix piles acting as a slab (ground improvement layer) below the final excavation level. The depth of excavation is about 10.12m from the existing ground level. The proposed solution kept the wall deflection below the limit of 0.7% of the depth of bulk excavation and avoided additional props leading to faster completion of the structure. With unsymmetrical loading behind the retaining walls, 2D finite element analysis was carried out to assess the wall deflection and stresses in the wall and the grout layer below. The diaphragm wall is instrumented to monitor the behavior and the findings are discussed in the paper.INTRODUCTIONConstruction in soft marine clay has always been a challenge to the engineer because of its very low shear strength and its sensitivity to disturbance. In the case of excavation projects the problem becomes even more complicated with development of excess pore pressure during excavation. Marine clay with its low shear strength and lesser passive resistance, generally leads to large wall movements and settlement behind the wall. Increased passive resistance coming from increased number of props is useful but has its limits and it is no longer the most effective way in containing or reducing the wall movements or forces in the wall. One of the solutions to these problems is to improve the soil shear strength by means of ground improvement infront of the wall at an elevation most appropriate to maximize wall performance. There are several methods adopted in improving a soil layer including mixing additives to the ground to improve the shear strength to partially replacing the weak soil while others are fully replacing the weak soil. This paper discusses the case study of approximately 10m of excavation in soft marine clay using 800mm thick diaphragm wall supported by Deep Mix Piles (DMP) being used to improve soft marine deposit to form a slab just below the formation level and thus improving passive resistance significantly. The ground improvement layer helped to reduce the wall forces and deflections making it possible to remove the need for additional temporary props leading to significant savings is time and productivity. The paper presents the various options explored before this method is adopted, the design approach, instrumentation data and the monitored results."

Jan 1, 2015

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Erwin Stötzer, Renato Fiorotto, Wolfgang G. Brunner, Manfred Schöpf

"Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yie ld unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drill rig. With this system much deeper walls can be installed and even hard soil layers can be penetrated. CONVENTIONAL SOIL MIXINGIn 1962 Norman Liver patented an auger-based soil mixing technique that has become the basis for the world's current technology.The deep mixing method (DMM), as it is known today, is an in situ soil treatment and improvement technology where the soil is blended with binders and/or other materials that are introduced in a slurry or dry form.Typically one or more hollow, rotating mixing shafts tipped with some type of cutting tool are mounted vertically to the mast of a base carrier and are driven into the ground by hydraulic or electrically powered rotary heads. The shafts above the cutting tool may be further equipped with discontinuous auger flights and/or mixing paddles. The binder is injected through the hollow shafts to nozzles located near the cutting tool where it is mixed with the ground to form columns of treated soil.Individual column diameters range from 0,6m to 1,5m and may extend to 40 m in depth. They can be arranged individually or in contiguous or secant patterns to produce a wide range of treated soil structures on both land and marine projects. Typical configurations are: Single elements, rows of overlapping (secant) elements, grids, lattices and blocks (Fig. 1 )."

Jan 1, 2005

By Jim Bruce, Naresh Gurpersaud

"The West Toronto Diamond project, under construction since 2006 and due to be complete in 2015, is a rail-to-rail grade separation project in the heart of urban Toronto. Once complete, a depressed corridor over 1000 metres long will take the CN tracks beneath the CPR tracks. An interlocking steel pile wall serves to retain ground and cut off groundwater. Remedial measures, constructed using jet grouting, were required at several locations within and behind the steel piles.At mechanical interlock joints damaged or suspected of being damaged, jet grouting was used to improve native soils on the retained side of the wall to reduce permeability of the soil mass in intimate contact with the joints to 10-7 cm/s. At a number of steel piles where groundwater and soil type combined to cause basal instability inside the pipes during the interim between excavation and concreting, jet grouting was used to construct temporary bottom seals. At locations near adjacent structures where the steel pile installation process resulted in disturbed ground on the retained side of the wall, jet grouting was used to strengthen and stabilize ground.This paper outlines the details of the various jet grouting applications, the respective testing programs implemented to demonstrate in situ permeability and strength of the soil-grout matrix, and performance of the constructed system.INTRODUCTIONThe West Toronto Diamond (WTD) is a junction of several railway lines, all intersecting at the same grade (Figure 1). A major grade separation project at this site commenced in 2006 and is scheduled to be completed in 2015. The whole of the work is comprised of multiple contracts, completed and/or ongoing, by different constructors. Once completed, a depressed corridor over 1000 metres long with over 23,500 m2 (face area) of retained earth will bring the CN tracks beneath the CPR tracks and eliminate a major bottleneck at the most heavily used rail crossing in Canada."

Jan 1, 2017

By John P. Briand III, Douglas J. Aghjayan, Robert E. Fosse

This paper highlights the successful pile load testing program for the redevelopment of Pier One in East Boston, Massachusetts. Pier One is a 5.4-acre parcel on a dormant waterfront site used in the 1950s as a warehouse and distribution facility. The developer plans to re-use the existing 14-inch-diameter concrete-filled steel pipe piles to support four 5- to 7-story apartment buildings above a 2-story parking garage. A pile load testing program was developed to establish if the existing piles could support design loads of 240 kips for project financial feasibility and up to 300 kips for a significant reduction in future foundation costs. The Phase 1 program consisted of statnamic and dynamic load testing on two piles with two loading intervals (200 and 240 kips). Based upon the favorable results of the Phase 1 program, the Phase 2 program involved statnamic load testing on two piles and dynamic load testing on ten piles with three loading intervals (200, 240, and 300 kips). The Phase 2 program confirmed the favorable results which were applied across varying strata thicknesses and pile embedment depths. The average allowable capacity for the piles tested was greater than 300 kips with pile movement up to 0.3 inches.

By Niels Krebs Ovesen

Close economic cooperation was established among the countries in western Europe during the seventies. As a consequence, among others, a need for harmonized technical specifications for civil engineering works arose. Technical specifications for design and execution of building and civil engineering structures exist in most of the European countries. In some countries such technical specifications are part of the building regulations and in other they are independent codes of practice and standards. The works on the Eurocodes was initiated by the Commission of the European Communities about 1976. The Eurocodes are intended as common unified design codes for different load bearing structures constructed from different materials. They are also intended to cover design of geotechnical structures. They are established with a view to promote the free movement of goods and services within the member states of the European Community - the so called Internal Market - and within the member countries of the European Free Trade Association, EFTA by removing obstacles arising from different rules for calculation and design.

Jan 1, 1994