Search Documents

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

By D. G. Bishop

This paper is intended as a review and update of the use of Pressure Injected Footings as deep foundation units in North America. We will discuss various aspects of this pile and then discuss a particular project - the Mobile Alabama Convention Centre which is currently under construction. Pressure Injected Footing is a generic name used to describe a foundation unit that has been in use around the world for some 80 years. It has been used on all types of structures. It is an excellent pile in both compression and tension. It is particularly economic where a layer of granular soils can be found at relatively shallow depths. Other types of piles would penetrate these layers. Caissons are often difficult to construct in these soils because of their lack of cohesion and the often present water table. PIFs can density these shallow layers and carry relatively heavy building loads on them.

Jan 1, 1992

By Gordon] [Reavis

Halliburton Services and Brown & Root have developed a unique foundation system that blends oilfield and construction technologies to construct deep foundations which offer significant advantages across a variety of soil profiles. This highly efficient system is being developed to meet the construction industry's needs into the 21st Century. Based on a concept initially introduced to Halliburton Services by V.L. Schellhorn in 1987, Halliburton combined their existing cement slurry mixing and pumping technology with oilfield drilling practices and a new tool design to field test the viability of the concept. Results looked encouraging, and Halliburton asked it's sister company, Brown & Root to evaluate and further develop the process. With Brown & Root's knowledge of the construction industry, the original concept has developed into a viable and efficient foundation construction system.

Jan 1, 1993

By Balu E. George, Subhadeep Banerjee, Shailesh R. Gandhi

"A three-dimensional analysis of laterally loaded helical piles installed in cohesionless soil is presented. Finite Element Analysis was conducted using commercially available Plaxis 3D AE version, assuming Mohr-Coulomb failure for soil. Pile is modelled as plate elements with a single helical blade attached to a hollow shaft. The ultimate load for various configurations is examined considering deformation criteria. The Bending Moment distribution and maximum lateral deflection are also discussed. It was observed that the ultimate lateral load carrying capacity increased by presence of helical blade and the maximum deflection also got reduced. The diameter of the helical blade was found to have significant effect on the lateral deflection, maximum bending moment and the ultimate load. However, the observations from the study suggest that the presence of helical blade seizes to produce considerable effect after a certain depth. Difference in failure pattern with regard to the distribution of soil resistance observed for different geometries considered for numerical analysis are also touched upon.INTRODUCTIONHelical piles or screw anchor piles have gained popularity due to fast installation, instant use, and other advantages over the traditional piles. They are usually used to support structures like solar panels, light houses, and other light structures which are subjected to uplift loads. However, such structures are often subjected to significant lateral loads as well. Under lateral loads, the response of helical piles can be different from that of a conventional pile due to the presence of the bearing provided by the helical blade. However, the proper design remains a concern due to lack of work carried out on the lateral capacity of helical piles.The lateral performance of helical piles is significant because they can act as efficient alternative to conventional piling systems in many applications.The lateral load capacity of screw anchor piles with different number of helices were examined by Mittal et al. (2010) by experiments in sand. They found that the lateral load capacity of piles increases with addition of helical blades. Prasad and Rao (1996) examined the lateral capacity of helical piles in clay by experiments on model piles and found that the lateral capacity of helical piles were more than that of the straight shaft piles. It was observed that the lateral capacity increase with embedment depth and shear strength of soil. Sakr (2009) studied lateral performance of two section helical piles in soft soil. The investigation by Prasad and Chari (1999) reported that the pressure distribution across the diameter is not uniform for circular piles, but it is maximum at the centre and almost zero at the two edges.Puri et al. (1984) after conducting model tests on single-helix, two-helix, and three-helix anchors installed in sand, proposed a mathematical model that was fashioned after Matlock and Reese’s elastic theory model. Elkasabgy and Naggar (2015) investigated he lateral performance of full scale large capacity helical piles in structured cohesive soils and reported the modulus of sub-grade reaction to be non linear."

Jan 1, 2017

By Sivilay Sayavong, David Puller, Julian Gatward, David Hard, Martin Stanley

"AbstractThe Thames Water Tideway Tunnels programme involves the upgrade of London’s combined sewer and storm water system. The first section is the Lee Tunnel between the Beckton Sewage Treatment Works (STW) and the Abbey Mills Pumping Station. This will intercept the overflows currently discharging to the River Lee and has the capacity to store and transfer 350,000m3 of storm water and sewage. The project required 4 shafts and a 6.9km 7.2m diameter tunnel. The shafts are some of the largest ever constructed in the UK, with diaphragm walls up to 98m deep and 1800mm thick. As a result of the innovative methods of diaphragm wall design and construction adopted the 4 very large and deep shafts were able to be excavated and completed safely, with minimal water ingress and with extremely high quality.MVB, a joint venture of Morgan Sindall, Vinci Construction Grands Projets and Bachy Soletanche are delivering the £635m contract with Thames Water’s Project Management Team in a collaborative manner under an NEC contract. Mott MacDonald, Morgan Sindall UnPS & Bachy Soletanche are acting as designers.Some of the important advances in diaphragm walling made included:??Diaphragm wall design to both EC2 & EC7 taking into considering the assessment of chalk stiffness, high hoop stresses, large multiple openings and non-axisymmetric loadings.??Formation of shafts as a faceted circle from a series of overlapping panels, with primary panels up to 7.2m wide demanding concrete volumes up to 1300m3 be poured in one go. Overlapping secondary single bite panels cut into the grade C50/60 concrete.??Excavation of the full geological stratigraphy of London making bentonite management complex.??Panel verticality of 1:300 required over the full depth. The results achieved this and in many cases exceeded expectations with some panels coming in at up to 1 in 800 with the majority at 1 in 400 to 1 in 500. The project is also the first in the Soletanche Bachy Group to take data from the ultrasonic drilling monitor used to check the verticalty in electronic format in order to create 3D CAD as-built drawings.??Each diaphragm wall panel was reinforced over its full depth. Up to 18 separate pieces of reinforcing cage had to be installed in primary panels. Cages underwent a full range of temporary works designs to check that lifting, splicing and placing could all be undertaken safely. Fibreglass was used in the tunnel portals in the shafts to ease breakthroughs."

Jan 1, 2014

By Reza Y. Khaksar

Presented is a rigorous solution for the three-dimensional stability analysis of vertical shafts (excavations) subjected to the self-weight of the soil based on the upper-bound theorem of limit analysis approach. A rigid-block translational collapse mechanism is assumed, with energy dissipation taking place along planar velocity discontinuities. This mechanism is optimized to obtain the critical failure mechanism giving the lowest factor of safety for stability of shafts. Based on comparisons with other solutions, the method is generally found to be accurate in predicting the stability of vertical cuts.

Jan 1, 2006

By Makoto Kimura

Failure tests on laterally loaded single and pile group are analyzed with a 3-dimensional elasto-plastic finite element program. In the analysis, the mechanical behavior of the ground is supposed to be elasto-perfect plastic with Drucker-Prager's yielding criterion. The nonlinearity of the piles is simulated by assuming a hyperbolic relation between the bending moment and the curvature of the piles. The influence of the axial stress on the cast-in-place concrete piles is also considered in the numerical analysis. It is found that the mechanical behavior of the piles subjected to lateral loading, such as the load-displacement relation up to an ultimately large deformation, and the distribution of bending moment in the pile group can be well simulated.

Jan 1, 1996

By Matthew E. Meyer

Renovation, rehabilitation, restoration and expansion of existing residential, retail, commercial, hospital facilities and historic structures requires assessment and evaluation of foundation systems of various ages. The concept of demolition and reconstruction in urban areas is often more challenging, costly, and even prohibitive in some cases due to historic regulations. The authors have been involved with numerous projects related to existing foundation assessment and retrofit, including: hotel and hospital expansions, historic Art-Deco hotel renovations and expansions, garage structure expansions, additions to prominent auction houses, casinos, printing facilities; high-rise structure foundation retrofitting; forensic evaluations of existing building and highway structure foundation systems, and marine bulkhead sheeting systems. The use of non-destructive testing techniques, high-strain dynamic load testing, full scale pile cap load testing and 3-D laser scanning technology has proved to be vital in the assessment and evaluation process, as well as design of foundation retrofit alternatives. This paper presents various methods and techniques to facilitate a phased approach for optimization of existing foundations and subsequent re-use of foundation systems. These methods and techniques are illustrated through the author?s experience and selected case histories from projects with varied foundation and geologic conditions.

Jan 1, 2011

By Charles Roeder, Amy Leland, Dawn E. Lehman

Concrete filled steel tubes (CFSTs) are composite members that are commonly used in many countries today. CFST components are used in the United States, but they are more common in Asia, in part because the connections used in Asia are quite labor intensive and there are not standard connections in the U.S. In addition, US design specifications are prepared by separate groups for structural steel and reinforced concrete structures and so composite systems that use CFST components are not overseen by a single group and as such there are several, conflicting design standards. In the US, steel tubes used for CFST are more slender (i.e., the diameter-to-thickness, D/t, ratio is larger) than some other countries, and labor practices (structural steel labor is different than reinforcing steel labor) also cause potential conflicts in construction. As a result, CFST has had some use in tall building construction in the US, but very limited use in bridge construction. A research program at the University of Washington has been in progress to address many of these issues with an eye towards universal design expressions, simpler, standardized connections and promotion of accelerated bridge construction (ABC). The research has resulted in recent changes to the American Association of State Highway Officials (AASHTO) bridge design specification as well as state departments of transportation (DOTs), which supports the increased use of CFST in bridge pile and drilled-shaft foundations. An experimental research study which investigate the flexural strength, shear strength and connections was conducted. These connections provide good performance under both seismic and gravity loads and address the concerns of US construction. These connections, their design rules and requirements, and their impact on composite behavior and system performance are discussed. These results permit rapid and economical construction of CFST bridge piers, piles and drilled shaft foundations. They encourage the use of more slender and economical tubes, while achieving the benefits of composite construction. INTRODUCTION Concrete filled steel tubes (CFSTs) are widely used for bridge and building construction in Asia, but the use of CFST in bridge construction is limited in the US. The historical use of structural steel and reinforced concrete in US bridge construction have resulted in more developed design expression for those construction methods, which has limited the use of CFST. Bridge construction in the US is inherently different than in Asia because of differences in codes, labor costs and construction practices. As a consequence, design and construction practices that are economical and practical in other countries may not be practical for US bridge construction.

Jan 1, 2019

By Mazin Adnan

The 80m high dam at the Peribonka river in the Canadian province of Quebec was designed for the generation of 385 MW of hydro electrical power (Fig.1). The complex ground conditions required the employment of a variety of geotechnical construction methods stretched to limits never experienced before. Innovative grouting and trenching techniques were used for the construction of a plastic concrete cut-off wall down to a depth of about 116m, to cut hydraulic seepage through alluvial deposits forming the dam foundation. The bedrock where the cut-off wall is embedded forms a glacial gully with steeply sloped flanks, which created further challenging conditions. [ ]

Jan 1, 2008

By John P. Turner, Benjamin J. Turner

"Tieback anchors are now used routinely for landslide stabilization in the USA and abroad. It is generally understood by design engineers that friction loss over the unbonded length of a tieback anchor is inherent to the system, and such loss is permitted as long as it does not exceed a certain threshold, typically 20 percent of the post-tensioning load. However, recent experience from projects utilizing tieback anchors with unbonded lengths in excess of 150 feet has demonstrated that this criterion may be difficult to achieve, particularly in certain ground conditions. Furthermore, anchor friction loss, even if below the 20-percent threshold, has important implications for the stability of the slope that are often ignored in practice. This paper presents the results of a study in which friction loss is quantified from load test data for projects in a variety of ground conditions by means of a “wobble coefficient.” Factors that may influence the wobble coefficient are examined, and recommendations for addressing this issue in practice are presented. A recent instrumented load-test program for a landslide stabilization project in Southern California is examined, demonstrating that with appropriate monitoring controls, uncertainty with regard to friction loss can be minimized. IntroductionSteel-strand tieback anchors have been used by the geotechnical community to support shoring systems for many decades, and more recently as a means to stabilize landslides. For strand encased in grease-filled plastic sheathing, which is intended to allow the strand to elongate freely, some load can still be transferred by friction between the strand and the grease and between the grease and sheathing. The sheathing then transfers load to the surrounding grout and, in the case of ground anchors, to the surrounding soil or rock. The resulting decrease in load over the length of the unbonded zone is known as “friction loss.”A widely used criterion for ground anchor acceptance based on load testing is that the measured anchor elongation must achieve a minimum value of 80 percent of the theoretical elastic elongation, or in other words the actual elongation can be up to 20 percent less than the theoretical value. This ensures that the majority of the load applied at the anchor head is reaching the bond zone behind the assumed failure surface, since load shed within the failure mass does not contribute to stability. This criterion acknowledges that friction loss is an inherent feature of the anchor system which cannot be eliminated completely, only minimized."

Jan 1, 2017

By Hayel M. El-Naggar, Sherif A. Akl

Although grouted piles have been used for several decades since the idea was proposed in the 1970s, their design is mostly based on experience and unpublished proprietary methods. There is little research on grouting drilled shaft tips and even less on grouting shaft sides. This paper presents the analysis of 4 instrumented pile loads tests on base and shaft grouted piles from different sites in Egypt; with emphasis on one of the tests, to demonstrate the analysis process. The data from the tests are analyzed to model the development of unit side friction (USF) with relative displacement. A numerical model using the finite element software PLAXIS is used to investigate the effect of grouting on the surrounding soil stress state. The paper combines the observations from full scale pile load tests and results from the numerical model to suggest an idealized behavior of side friction development with relative displacement of the grouted part of the shaft. The suggested model considers an envelope of Unit Side Friction (USF) with relative displacement, initially dominated by the grout resistance then at higher relative displacements, the friction with radially pressured soil takes over. The grout provides very high USF values up to a relative displacement of 2mm. Then, the USF drops to a typical pile soil side friction behavior; however, this friction is affected by the contact stress between pile and soil, which significantly increases due to compaction grouting. INTRODUCTION Base and shaft pile grouting has been significantly developing in recent years to accommodate the unfavorable conditions in major projects such as the high loads in high rise building and founding on problematic soil formations. Grouting aims to decrease settlements and increase the capacity of the pile under axial load. The technique is first introduced by Kraft (1974) but gained popularity in the 1980s. Typically there are two types of grouting; compaction, and permeation. Compaction grouting is more common in pile foundations practice, and many researchers have provided case histories of pile load tests on base grouted piles and base and shaft grouted piles (Gouvenot and Gabaix,1975; Stocker, 1983; Ghazali et al., 1988; Fleming, 1993; Kusakabe et al., 1994; Robson and Wahby,1994; Joer and Randolph, 1998; Hamza and Leoni, 1998; Mullins et al. 2000; Littlechild et al., 2000; Suckling and Eager, 2001; Dapp and Mullins, 2002; Ho, 2003; Fu and Zhou, 2003; Brettmann and NeSmith, 2005; Ruiz, 2005; Mullins, 2006; Dapp and Brown, 2010; Beadman et al., 2012; Nguyen et al., 2013; Miller et al., 2013; Sinnreich and Simpson, 2015; Hui and Lin, 2015). Compaction grouting is meant to densify the soil around the pile and below the base rather than permeate this soil and increase its cohesion. Research showed that grouting increases the capacity of the piles by a factor of 2~5. The variation in capacity increase depends on pile type, grouting process, and especially grouting pressure. Although there are many case histories of pile load tests on grouted piles but there is no well-defined agreed-upon method to predict grouted pile capacity as typically done in ungrouted piles. Few lab experiments discussed the shaft grouting effects on the soil especially the compaction grouting. The experiments concluded that the compaction grouting forms a homogeneous layer between the pile and the soil, and a residual effective stress is achieved simultaneously with a significant densification of the soil around the pile with noticeable decreasing in void ratio. (Fattahpour et al., 2015; Wang et al., 2015). Recently, studies used numerical analysis to investigate the behavior of the grouted piles and the changes in the surrounding soil (Chiang et al., 2013). That study presents a simulation of the base pressure grouting with a simple FE model and predicts the reduction of the pile settlement by 10 to 20%. Another numerical study using a complex model conducted by Zhou et al. (2017), pr

Jan 1, 2018

By Mait Mets

In Estonia, the deformations monitoring of 1500 buildings are currently under investigation, buildings on pile foundations make up 10 per cent of these. In the following text we will be considering the behaviour of pile foundation buildings in various parts of Estonia, in differing geotechnical conditions.

Jan 1, 2002

By A. K. C. Chan

Recent hotel investment projects in China often involve very tight programmes for design and construction. An example given in this paper involves a 24-storey reinforced concrete hotel tower with 460 bedrooms and a 3-level podium commercial complex. The building is supported by relatively widely spaced columns and shear walls below which 88 number large diameter piers were excavated through fill, silty and bouldery clay on to dolerite and slate at depths between 15 to 3 0m below ground level. Whereas much experience has been accumulated in Hong Kong, hand-excavated pier foundation was only adopted for the first time in Dalian. This paper describes and discusses the various factors influencing the choice of the type and design of the foundation system. The criteria for determining appropriate founding levels are then explained. During installation, revisions to the acceptance procedure were made to cater for local conditions. Emphasis is placed on the role of the geotechnical engineer in making on-site decisions during construction. The advantage of the foundation system in accommodating on-site changes resulting from local complex ground conditions is demonstrated. The pier foundations were successfully completed ahead of programme.

Jan 1, 2010

By Thomas Passlick

By means of further developed machines and techniques and with growing experiences in jet grouting, the challenge of this building method becomes more and more complex. To keep the concerning risks as low as possible, the requirements on the quality assurance continuously in­crease. The construction of a 37.0m deep seated slab for the Amsterdam metro station Vijzelgracht in marine clay represents such a complex task. This paper summarises the required measures of quality assurance. In particular a new hydraulic measuring device is introduced with which it was possible to detect the column diameter of 2.6m at a depth of 37.0m during the production process and with a very high accuracy.

Jan 1, 2006

By Muttharam M, Karthick Kumar V

Helical piles foundation systems have been extensively used in engineering application. It is commonly adopted to resist the compression, uplift force, overturning moment and lateral forces. Helical pile system is extensively used in many structures such as Transmission towers, Wind farms and other offshore structure because it is easy and quick to install. Realizing the importance of helical pile, an attempt is made in the present investigation to bring out the effect of spacing between the helix, blade thickness, and shaft thickness through numerical analysis. To validate the finite element model experimental investigation was carried out. In this investigation model steel piles with dual helical plate embedded in clay bed with the consistency of 0.4 was tested to study the effect of uplift loading on the behaviour of piles in tensions. Model helical pile with 12.5 mm diameter circular shaft and helix diameter of 25 mm. The model pile embedded in clay bed for a depth of 400 mm. Parametric analysis of helical pile by varying blade thickness, shaft thickness, and the spacing of helix was carried out by using Finite Element tool Plaxis 3D. From this analysis, an increase in thickness from 4 mm to 10mm increase the uplift load. Similarly, an increase in spacing of helices from 0.5 m to 1.5m increase the uplift capacity beyond that it decreases the uplift capacity. By keeping the contact area of the helix as constant as the number of a helix and helical spacing was varied, the critical number of the helix was found as 2 and the critical spacing of helix was found as 1.5 m for this study.

Nov 1, 2022

By Tatsunori Matsumoto

In order to investigate the variation of the load-displacement relations of piles in a site, vertical load tests were carried out on 25 small diameter steel pipe piles. Out of 25 piles, 15 piles were close-ended pipe piles attached with a blade at the pile toe and 10 piles were open-ended pipe piles. To carry out these load tests in a short period, two types of rapid load test methods, Spring hammer load test and Falling mass load test, were employed. The load tests of all piles were completed in two days with 180 blows in total. In order to estimate a static load-displacement of a pile, non-linear damping method was used. It is shown from the test results that the performance of the pipe piles such as the ultimate pile resistance and the initial pile head stiffness is improved by re-driving.

Jan 1, 2006

By Peter Florian

At 5:50 am on October 1, 1992, the new $800 million Pittsburgh International Airport Midfield Terminal opened its gates to the world after five years of construction and more than 24 years of planning. Despite numerous design changes, this massive project was completed on time and substantially within budget. The importance of this airport to Allegheny County and the Pittsburgh region was recognized 24 years earlier by Allegheny County Commissioners Tom Foerster and the late Leonard Staisey. Staisey and Foerster established a program to acquire land for the "Airport of the Future".

Jan 1, 1993

By William D. Spielvogel

The Massachusetts Highway Department awarded the Porter Street Outfall Project to the J.M. Cashman Company in November 1991. Timely completion of the Project in one and one half years is critical to the start of the subsequent Third Harbor Tunnel North Approach project. Existing subsurface conditions and the Project's location at Boston's Logan International Airport significantly increases the difficulty of construction. The major contractual work involves relocating a reinforced concrete double box culvert supported on a continuous wood pile foundation. This existing culvert crosses and interferes with the future Third Harbor Tunnel North Approach alignment. Two parallel culverts constructed approximately 20 feet from either side of the future Third Harbor Tunnel alignment replace the existing double box culvert structure. Under the original contract design, approximately 3,100 feet of 14 ft. by 15 ft. reinforced concrete culvert is cast in place adjacent to the west side of the Third Harbor Tunnel and is located in the center of the Airport's main service roadway, Harborside Drive. This culvert is the Porter Street Combined Sewer, PSCS, which handles a combined flow of sewerage from the East Boston community and storm water runoff from Logan Airport. In addition, approximately 2,230 feet of 17 ft. by 15 ft. reinforced concrete culvert is cast in place adjacent to the east side of the Third Harbor Tunnel and is within 20 feet of an active aircraft taxiway and heliport. This culvert is the Bird Island Flats Storm Drain, BIFSD, which handles storm water runoff from the Logan Airport airfield. The existing outfall, on the west side of the Third Harbor Tunnel alignment is to remain in service and is to be connected to the new PSCS and BIFSD culverts. Therefore, a portion of the BIFSD culvert is designed as a bridge to span 128 ft. across the Third Harbor Tunnel excavation during construction.

Jan 1, 1994

By Patrick J. Lydon, Gregory A. Terri

"The recently opened Mansueto Library at the University of Chicago campus was a 2012 OPA runner-up. The dramatic elliptical shaped dome of this structure tells only part of this structure’s story. The underground automated storage and book retrieval system below ground required excavations as deep as 55 ft (17 m). The system that allows the University to store many of its publications well below grade also required an approximately 50 ft (15 m) clear span for the perimeter walls between the lower level and street level slabs. The latter requirement allows the conveyors to operate freely to retrieve and transport publications up to the lobby level. The design-assist-build team worked together to develop the most cost-effective solution for below-grade work in this challenging urban and geologic environment.The perimeter of the new oval-shaped library is over 620 ft (189 m) long and sits in a central location on campus—adjacent to the Regenstein Library and two city streets and the Henry Moore sculpture, which commemorates the location of the first self-sustaining controlled nuclear reaction. The new library construction not only had to meet challenging structural and geotechnical requirements, but also had to be sensitive to its active and historic surroundings. The soils at the site consist of about 25 ft (7.6 m) of sand, followed by lean clay, generally increasing in stiffness to the top of the dolomitic limestone. Five to 10 ft (1.5 to 3 m) pockets of saturated sand also lie on the north side of the site at about 45 ft (13.7 m) below grade. The top of weathered rock varies in elevation from 59 ft (18 m) below grade in the south to 69 ft (21 m) in the north. There is 1 to 2 ft (30 to 60 cm) of weathered rock. Groundwater at the site is about 7 ft (2 m) below grade.The new structure would extend 55 ft (17 m) below grade through saturated sand strata and into weathered rock for part of the structure’s footprint, so it was critical that the new permanent retention system minimize groundwater seepage laterally through the structure’s wall as well as piping through the weathered rock below the structure. The perimeter walls had to be very stiff to minimize ground movement around the structure’s perimeter due to the significant clear span between slabs."

Jan 1, 2013