Search Documents

Jan 1, 1984

By Alper Turan

The use of aggregate pier foundation systems has become widespread as the engineering practice moves towards cost-effective ground improvement solutions that provide accelerated construction schedules. Increased bearing capacity, effective settlement control and potential for liquefaction mitigation are commonly acknowledged benefits of aggregate piers. This paper studies the mechanisms by which aggregate piers interact with each other and with the surrounding ground when excited by seismic loads. A particular emphasis was placed on the response of a raft foundation supported on a site improved using aggregate piers. Three-dimensional nonlinear finite element analyses were conducted using commercial software package, ABAQUS. Non-linear soil behaviour is modelled using a three-dimensional total stress-based bounding surface plasticity model, which is able to simulate stiffness degradation and damping increase in the soil. The soil stratigraphy considered in this study was a 30 m deep soil deposit that comprised a very stiff base layer and a shallow soft surficial clay layer. Ricker Wavelet time histories with different frequency contents are used as the excitation force in the analyses. Various area replacement ratios (ARR) for aggregate piers are studied for a square plan layout. The results presented in this study are considered to be of interest to researchers and designers in evaluating the seismic ground response of the sites improved using aggregate piers.

By A. Felipe Uribe-Henao, Camilo Ballesteros, Luis G. Arboleda-Monsalve, David G. Zapata-Medina

Conventional excavation analysis based on total or effective stress methods can result in inaccurate estimation of ground movements when impervious soil conditions or rapid excavation sequences are not found in the excavation (i.e., assumption of undrained response is not valid). The influence of excavation rate, hydraulic conductivity, and excavation geometry on the fully coupled solid-fluid behavior of a braced excavation in cohesive soils are studied parametrically using PLAXIS2D. The coupled excavation analysis is performed using the Hypoplasticity clay model to reproduce the constitutive behavior of soil and the poro-elasticity Biot’s theory to account for changes in pore water pressure due to deformations in the soil skeleton. Results obtained from the parametric studies indicate that excavation rates to hydraulic conductivity ratios, ER/k, smaller than 0.1 and larger than 104 can be used as limits for drained and undrained analyses, respectively. In practical applications, undrained and partially drained excavation analysis with ER/k larger than 102 resulted in a similar ground deformation. However, smaller ER/k ratios demand fully coupled solid-fluid analysis. An analytical method aimed at predicting excess pore water pressures and determining the required type of analysis associated with soil and excavation conditions, e.g., drained, partially drained, and undrained analysis, is proposed herein to accurately estimate the ground movements induced by the excavation.

By Sushant Upadhyaya, Deniz Karadeniz

As part of the widening of I-64 in Williamsburg, Virginia, an extensive subsurface exploration program consisting of Standard Penetration Tests (SPT), Cone Penetration Tests (CPT), Dilatometer Tests (DMT), and Vane Shear Test was performed. In addition to these in-situ tests, an extensive laboratory testing program was completed including Consolidated-Undrained Triaxial, Unconsolidated-Undrained Triaxial, Direct Shear, and consolidation tests. The strength and the compressibility properties are deemed conservative for Yorktown and St. Mary’s Formations when evaluated based on the current topography, the existing overburden pressure and SPT values. SPT exhibited low blow counts especially within Yorktown Formation due to the increased excess pore water pressures resulting in a localized liquefaction at the tip of the split spoon sampler corresponding to remolded or fully softened strength of the soil. Therefore, the applicability of the SPT correlated soil parameters somewhat leads to conservative designs with deeper piles to achieve a desired structural load demand. Generally, the in-situ estimated soil design parameters are found to be comparable with the laboratory test results corresponding to long-term resistance gain with time. It is of practical importance to employ realistic soil design parameters for design applications such as pile foundations to provide cost and schedule savings. This paper presents a discussion on the soil strength estimates and variability from in-situ and laboratory tests for realistic strength characterization of Coastal Plain deposits.

By Rick Deschamps, Amanda Blank, Matthew W. Drewek, Michael P. Walker

The Prairie du Sac Dam, located on the Wisconsin River, northwest of Madison, Wisconsin, was constructed 1912-1914. The spillway is an Ambursen-type, consisting of a series timber pile supported pier and buttress walls and rollway slab. The timber piles supporting the spillway, numbering approximately 5,000, have deteriorated, and the spillway structure was underpinned with over 700 micropiles as part of a design-build construction project. The underpinning micropiles needed to be arranged to avoid interferences with the existing timber piles, requiring the micropiles to be installed in the open spaces between the piers and buttresses. Inevitably, the installation of the new micropiles encountered obstructions, including existing timber piles out of alignment, as well as timber piles used to support the original construction activities and sheet pile used to control water during the original construction. This paper discusses using finite element analysis to model the spillway structure to estimate the vertical and horizontal stiffness with an extensive sensitivity analysis was performed during the design phase to account for anticipated construction challenges and potential variations in the underpinning performance. The inherent rigidity of the spillway structure allowed for load distribution to the underpinning system even when new micropiles needed to be re-located and aligned to avoid interferences with existing timber piles and other abandoned foundation elements dating back to original construction.

Sep 8, 2021

By Za-Chieh Moh

This paper presents a summary of the current pile foundation practice in Taiwan. Constructions of driven piles, drilled shafts, and barrette foundations are reviewed. This paper also briefly summarizes the pile works of four major construction projects in Taiwan, namely, Hsin-Ta Power Plant, Taichung Power Plant, Taipei Transit Systems, and Taiwan High Speed Rail.

Jan 1, 1996

Jan 1, 1985

By Chu E. Ho

This paper reviews the design of jet grouting at re-entrant corners of excavations where the diaphragm wall and secant pile wall installation were interrupted by existing utilities in the streel sidewalk. Jet grout blocks were formed to seal the gaps in the walls for excavation support, consisting of four to six columns in clusters. Jet grouting was performed around an electrical duct bank which had to be maintained. Jet grouting was executed through stratified soils using various combinations of jetting parameters for different soil strata. The installation sequence and age of the neighboring columns within a cluster will affect the jet’s ability to form subsequent columns. When jet cutting is limited next to hardened grout columns or embedded obstructions (such as diaphragm walls or secant pile walls in this case), the specific gravity (SG) of spoils would be reduced and tend toward the value of the injected grout SG. The magnitude of spoil SG is also influenced by the variability of the grout mix supplied. Specific Gravity Ratio (SGR) defined as the ratio of spoil SG to the actual grout SG at the time of jetting can be used as an indicator of successful treatment, with SGR > 1.0 indicating effective soil erosion. Verification coring and testing were implemented to confirm target column diameter and strength of grouted soils have been achieved.

May 1, 2022

By Mark Zablocki, Dakarai McCoy

Ground vibrations are an unavoidable effect of driving piles and may pose a risk to nearby infrastructure and the comfort of adjacent occupants. Driven-pile-induced ground vibrations are known to vary widely based on ground conditions, pile material, and installation means and methods. A monitoring sensor to record ground vibrations during pile driving is necessary for understanding potential impacts to sensitive infrastructure and should be considered when implementing a monitoring program anticipating ground vibrations. The implementation of a vibration monitoring program historically relies on experiential-based decision-making, which may result in the costly vibration monitoring of low-risk infrastructure. Prior understanding of anticipated ground vibrations is necessary to create an appropriate monitoring program. A framework is proposed for organizing data from past monitoring programs and quantifying the anticipated risk of driven-pile-induced vibrations. An example of risk quantification from data imported to ]a cloud database is presented by comparing driven steel H-pile and prestressed precast concrete vibration monitoring measured and collected by Haley & Aldrich between 2010 and 2020. The methods presented within the example can be applied to quantify a first order approximation of risk for ground vibrations at proposed driven pile sites based on the measured performance of previous sites with similar ground characteristics and pile installation methods. The presented novel data managements tools allow for a quick aggregation of vibration data with similar site conditions.

Sep 8, 2021

By BRETTMANN TRACY

Jan 1, 2000

By David White

"When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100’ of water are well known, let alone in the open waters of the South China Sea.In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130’ long, 72’ diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE’s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.INTRODUCTIONThe challenges of driving individual steel sheets in deep water are well known, let alone in the open waters of the South China Sea. Often the challenges of construction are overcome with engineering or equipment. The challenges of China’s Hong Kong-Zhuhai-Macau Bridge, on the drawing board since 1983, were to overcome both. The challenges of overcoming the skepticism of the Chinese Engineering community would be another story.The finished project will comprise three cablestayed span bridges and a 4.15 mile immersed tube tunnel linking Hong Kong on an eastern span to the China mainland cities of Zhuhai and Macau via two western spans."

Jan 1, 2017

By Venugopal B, M Kumaran, Thomas John, Vetriselvan A

The initial pile load tests are conducted to ensure the geotechnical capacity of the pile in a particular site condition. Normally kentledge method is adopted for the compression pile load tests. In this method the entire kentledge load is loaded above secondary beams which are supported by concrete blocks above the Natural Ground Level. So, it is important to ensure the SBC (for shear and settlement) of the natural ground. In one of our projects initially it was decided to go with kentledge system for initial compression load test on 56m long 1200mm diameter BCIS pile. The test load and total kentledge load were 2160t and 2700t, respectively. The soil strata mainly consisted of clay with low SPT N value and water table almost at ground level. It was suggested to replace top soil using Granular Sub-base (GSB) with good compaction in order to avoid excessive settlement of concrete blocks placed to support the kentledge weight. When the kentledge loading started, even before reaching 10% of total kentledge load, excessive settlement on the GSB layer was observed. This paper describes the problems faced during normal kentledge method and how it was overcome using the liner pile system for initial compression load tests in this particular site condition for higher test load.

Nov 1, 2022

Jan 1, 1993

Jan 1, 2002

This manual is limited to Augered Cast-in-Place (ACIP) piles constructed using a hollow stem continuous flight auger. 1.1SCOPE AND LIMITATIONS The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Cast-in-Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010

By Matthew E. Meyer

The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Castin- Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010

By Abid O. Adekunte

The design, construction and monitoring of the deep excavation support for the basement of a large-scale commercial development in Cavan, Ireland is presented. Excavation area was adjacent to existing structures and retained height H varied between 4.0m ? 11.0m. In areas where excavation depth H < 5.0m, wall was designed as cantilevered section. However in sections where 5.0m = H = 11m, additional wall supports were required for serviceability reasons. Traditionally, designers often provide additional wall support through the use of tie-back ground anchors, raking props and braces. On the current project, the main contractor was not in support of the use of temporary props so as to maximise working space, while owners of adjacent properties disapproved the use of tie-backs. The limited set-back between the wall line and site boundary also contributed to the complexity of the project. A rare alternative solution has been adopted. This novel approach involved buttressing the wall with steeply raking bored tension piles at regular intervals along the wall. Comparison of the monitored deflections in the cantilevered sections with those recorded at sections where tension piles were used shows the novel solution to be safe and quite effective. This approach is also considered to be more economical when compared with ground anchorage and propping.

Jan 1, 2008

By Glen Mann, H. G. Vestberg, Robert D. Holtz

"Underpinning of residential and commercial structures is often accomplished using a number of driven-in-place small diameter steel pipe piles. These piles, at least in the Seattle area, are typically described as pin-piles and are driven with an air compressor operated jack hammer to a refusal criterion developed from an empirical basis. Over the past twenty years or so, the materials have improved in quality and strength, and the driving equipment has improved in efficiency and capability. These improvements have resulted in damage to the pin-piles during driving as well as to the driving equipment. The primary objectives of this load testing study were to develop a relationship between the driving penetration resistance of 2-inch diameter pin-piles and the ultimate bearing capacity when piles were driven at different penetration rates and, based on the load test results, to develop an opinion regarding an increase in the allowable axial load capacity [ultimate load capacity divided by a factor of safety] of a 2-inch diameter pin-pile over the currently used permissible load capacity of 4 kips in the Seattle area. Also, if feasible, a reduction in the present driving penetration rate was to be recommended to help reduce the rate and magnitude of pile and equipment damage whilst maintaining the allowable load capacity. The recorded ultimate bearing capacities were also compared with the Tagnent-line and the Davisson analytical methods in an effort to determine if either of these provided a reasonable determination of the pile load capacity.IntroductionThis paper describes the results of a series of load tests performed on small diameter, 2-inch, driven-in-place steel pin (pipe) piles and based on these results, provides the support for a modification to the presently used allowable axial pin-pile capacities.The intent of the load testing program was to determine how much influence the penetration resistance might have on the individual piles' ability to support the allowable axial load without undergoing any significant vertical deformation. For the purposes of this paper the ""allowable load capacity"" is considered to be the ultimate pile load capacity divided by a minimum factor of safety, typically considered to be 2.0 in this area. A pin (pipe) pile comprises an open or closed ended, schedule 80 steel tube which is driven-in-place, usually with an air compressor operated 90 pound pneumatic jack hammer. These jack hammers typically operate at a rate of about 1,200 blows per minute, (Haggard, Holtz and Mann, 2001 )."

Jan 1, 2005

Jan 1, 1997

By Seth Robertson, Daniel Belardo, Travis Coleman

Thermal Integrity Profiling (TIP) is a non-destructive method used to evaluate drilled deep foundation integrity. This integrity testing method is specified more frequently, and is becoming an industry standard in the transportation and private construction sectors. This testing method utilizes heat generated during the concrete/grout curing process to assess deep foundation integrity over the evaluated length. With compilation of the measured temperature versus time and installation records, a model of the Effective Average Radius versus measurement depth is generated. The generated effective shaft model is highly dependent on specific construction details, subjective modeling parameters, and proper interpretation of concrete/soil heat dissipation characteristics. Key components of the TIP analysis include both qualitative and quantitative assessments. Qualitatively, variations or sharp reductions in temperature profiles may indicate potential anomalous regions. Quantitatively, a correlation is established between measured temperatures and estimated Effective Radii for subsequent integrity evaluation. Best practices in processing the TIP measurements are presented, including selecting the optimal time for analysis, normalizing the thermal profile, and proper interpretation of potential anomalous regions. Recommendations for implementing mitigation efforts and interpretation of the TIP results are presented.

Sep 8, 2021