Search Documents

By Jewels Stover, Charles A. Luxford

Oklahoma City is undergoing a replacement program for an existing 66in (1.675m) water pipeline that conveys raw water from Atoka Reservoir to the City. This pipeline currently crosses the Canadian River on elevated piers and is subject to flood hazards. To replace the existing pipeline and mitigate flood damage concerns, two parallel microtunnels will be constructed below the river channel. Access is from construction shafts located near the midpoint of the tunnels; opposing drives are launched from each shaft. This geometry dictated shafts of significant depth – exceeding 120 ft. (37m). To accommodate the casing pipe segments and microtunneling machines, a minimum shaft diameter of approximately 34 ft. (10.4m) was required. Due to the difficult geologic setting, a reinforced secant pile compression ring is specified by contract in the top 70 ft. (21.3m) of these construction shafts to provide a very low permeability support system.

Sep 8, 2021

By Sung-Ryul Kim, Woong-Jong Park, Juhyung Lee, Si-Hoon Lee

"A bucket foundation has been considered to be a potential foundation technology for offshore wind turbines. In this study, a series of 1-g model tests were performed to analyze the accumulated rotation of suction bucket foundations under long-term cyclic horizontal loads. The model suction buckets were made to have the embedment ratios of 0.5 and 1. The dry model ground was prepared to have two different soil densities by air-pluviation method. A horizontal cyclic load over 104 cycles was applied varying the loading amplitude. Test results showed that the accumulated rotation of the bucket foundation increased with the increase in the number of cycles and load magnitudes. Based on the model test results, a new equation was proposed to evaluate the accumulated rotation of the bucket foundations in sandy ground under long-term cyclic horizontal loads.INTRODUCTIONRecently, a bucket foundation has been considered to be a potential foundation technology for offshore wind turbines. In terms of economy, a bucket foundation has been considered to be an economical foundation type at sea beds where ground condition is clay or medium dense sand.A bucket foundation resembling a bucket is a kind of suction-installed foundation units. It is a skirted steel foundation which is open at the lower end and closed at the upper end by a lid. The embedment depth ratio (L/D) of a bucket foundation is usually less than one. Figure 1 shows an example of a bucket foundation. Offshore wind turbines are subjected to long-term cyclic loading by wind or currents. A bucket foundation is installed in soil grounds, so the long-term cyclic loading may induce the accumulation of soil deformation.In this study, the accumulated rotations of the bucket foundations in sandy ground were investigated under long term cyclic horizontal load. The number of cycles up to 104 cycles was applied varying load magnitude. The accumulated rotations of the bucket foundations in sandy ground were analyzed based on the test results."

Jan 1, 2016

By Braxton P. Erbe, Douglas C. Brunot

A variety of systems and techniques exist to support deep excavations where sloping is not feasible. This paper will explore an example project involving the use of pre-engineered hydraulic bracing systems to support sheet pile walls. Challenges on site that drove the final design include a high water table, irregular excavation geometry, and underground obstructions. The hydraulic system, connected by pins and not requiring welds, allowed for quick deployment and the modularity to change as required due to unforeseen site conditions.

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By Murad Y. Abu-Farsakh, Md Habibur Rahman

The properties of all natural soil deposits are highly variable, and they are rarely homogeneous. Cone penetration tests (CPT) were used to assess the site variability, which was then incorporated into the Load and Resistance Factor Design (LRFD) of pile foundations. Data from six project sites with multiple CPT tests conducted at various locations were collected for this research. The semi-variogram was used to assess the spatial variability of CPT data (corrected tip resistance, qt) for each location. For each location, the coefficient of variation due to spatial variability (COVR,spatial) was calculated. From COVR,spatial and COVR,method, the total coefficient of variation (COVR,total) for each site was calculated, which was then used to calibrate the resistance factors (ϕspatial, ϕtotal) for use in LRFD pile foundation design. The findings of this study demonstrated the importance of using site variability in LRFD pile design. For sites with lower site variability than the design method (i.e., COVR, spatial < COVR, method), the value of the COVR, total will be decreased, and hence the resistance factors (ϕspatial or ϕtotal) will be increased (credit), and vice versa.

Sep 8, 2021

By Seyyed Mehdi Radeghi Mehrjou

The current work investigates the behavior of inclined micropiles under seismic loads. The dynamic finite element method (FEM) was employed. Rayleigh damping was applied to the soil, and elastic beam elements were employed to model the micropiles. The micropile structure was assumed to have one degree of freedom as a column with concentrated mass. The numerical modeling of micropiles was performed to explore the effects of their inclination on their seismic performance within homogeneous soils with uniform stiffness. In addition, the effect of soil stiffness was studied by considering various stiffness in soil depth. The results from the studies have shown significant effects on the dynamic amplification and internal seismic-induced loads of inclined micropiles.

Sep 1, 2022

By D. Cantali

This paper will be presented in two parts. The first part will present the latest advancements in pile installation techniques using state-of-the-art press-in piling technology by Giken. By pressing in sheet piles and large modulus contiguous steel tube pile walls – as opposed to the more traditional installation methods using percussive hammers or vibrators – retaining structures can be constructed effectively noise and vibration free. For over water and coastal projects with limited access, this provides significant environmental benefits in the form of minimising the construction foot print and the impact to surrounding communities and the marine natural habitat. Typical noise and vibration data will also be presented. The second part of this paper will review the current manufacturing techniques for sheet piles and introduce innovative new materials used in the current piling market for embedded sheet pile walls. Materials include long service life non – ferrous materials such as new age plastics and fibre reinforced polymer piles. Their excellent long term performance and durability make them an effective solution in the marine environment. For steel piles, a number of steel grades with reduced corrosion characteristics will also be discussed including a newly developed steel to combat corrossion in the low water zone, an area often exhibiting the highest moments in a retaining wall. A number of project case studies will also be presented to reinforce their relevance in today’s changing construction landscape.

Nov 1, 2022

By Akhila Manne, Prasad P. V S R

Storage tanks are heavily loaded thin-shelled structures that exert large loads on and require large foundations to support them. They are generally very sensitive to foundation settlements as it may hinder the performance of tanks resulting in significant commercial or social impacts. Selection of their foundation is dependent on availability of suitable ground and limitations imposed by design specifications. Design of the tank foundations is generally based on theoretical methods and validation by representative field tests. This paper reviews settlement criteria for storage tanks as per national and international standards, case studies of large to medium diameter tanks supported on deep foundation i.e., bored cast-in-situ piles and shallow foundations on improved ground and their performance during load tests & hydro-tests is discussed. Paper concludes that storage tanks can also be supported on shallow foundations resting on improved ground reducing the settlement, time and cost significantly depending on the sub-soil.

Nov 1, 2022

By Joel B. Dellaria, Justin R. Lewis

"No. 9 Walton is a new high-rise condominium building located in the Gold Coast area of Chicago. The adjacent building, Walton on the Park, featured 4 levels of below grade parking and utilized a secant pile wall with integral drilled shafts to support the exterior columns. The earth retention system (ERS) for No. 9 Walton also employed a secant pile wall in combination with drilled shafts. The excavation into the soft Chicago clays varied in depth from 9.75 m to 12.5 m (32 feet to 41 feet) below grade. The temporary excavation support used internal braces from the new secant piles to the existing foundation system of Walton on the Park to provide earth retention. Engineering teams for both projects worked together to design the bracing scheme and connections to ensure that the new excavation and internal bracing would not overstress any elements of the existing structure. Further complicating the project, immediately to the west of the project was a historic church founded on shallow spread footings which required underpinning to minimize movements.The project involved three different building owners, small values for acceptable wall movement, an extensive monitoring program and the challenges of merging two earth retention systems. The subsurface conditions at the site, the adjacent structures, the excavation, and the performance are described. A summary of the design methods and the expected movements of the ERS are discussed, and the performance monitoring system is described. Overall, the ERS performed better than expected with less than 1 inch of measured lateral wall movement during and after the excavation was completed. Measured performance of the ERS is compared to the predicted performance and to the performance requirements for the project.INTRODUCTIONNo. 9 Walton is a new high-rise condominium building in Chicago located in the Gold Coast. The building has 3 levels of below grade parking and 36 levels of living space above grade. Developers originally slated the project to be Phase 2 of the Walton on the Park development built in the mid 2000’s, using portions of the existing foundation system for development of the new structure. However, the housing market crash in 2007 prompted cancellation of Phase 2 of the Walton on the Park development. The property sat undeveloped until 2015 when design and construction for No. 9 Walton began under a new development and design team. The project team completed foundation excavation and below grade structures in 2016 with the first units of the building turned over to new homeowners in 2017.The structural design for No. 9 Walton consisted of reinforced concrete columns and slabs, supported laterally by a heavily reinforced concrete central core. Drilled shafts to rock supported the interior columns and core with the exterior columns and foundations integrally included in the earth retention system. The structure had a below-grade footprint of approximately 1,490 m2 (16,000 ft2). The general excavation extended 9.75 m to 12.5 m (32 feet to 41 feet) below street level with the deepest portions at the central building core mat foundation."

Jan 1, 2017

By Peter Deming

"PART 1 OF 2INTRODUCTIONSlurry trenches are the least cost hydraulic barrier available, if the excavated spoils can be recycled into backfill. As such, slurry trenches are constructed where possible, sometimes at high risk. Slurry trenches are also used to install biopolymer drainage trenches, which have a low safety factor because the biopolymer slurry weight is marginally greater than the weight of water. In marginal ground the construction risk falls to both the Owner who designs and asks for the construction, and the Contractor who manages the work and promises to complete the project successfully. This paper discusses design and construction of slurry trench barriers in marginally stable ground and where groundwater chemistry invokes the need for slurry management details to obtain proper backfill placement.As a designer, Mueser Rutledge Consulting Engineers works for both Owners and Contractors. We are usually able to convince Owners of their responsibility for design detailing in order to obtain a working final product and to obtain reasonable bids from Contractors by disclosing construction needs and designing to reduce the contractor’s exposure. We often work for Contractors to produce designs which result in successful construction in projects where the Owner’s engineer places the responsibility of design and construction on the Contractor.This paper is intended to inform both Owner and Contractor audiences of resources which are available to reduce the risks of trench collapse in difficult ground conditions. We hope it serves this purpose.DESIGNSubsurface InvestigationsSubsurface conditions should be defined by borings focused on definition of the soil profile and soil design parameters. After general subsurface conditions are defined, barrier borings should be drilled along the final alignment.Definition of Soil Strength and CompactnessCompactness of sand and gravel strata should be defined with Standard Penetration Test N-values. The shear strength of cohesive materials should be defined by laboratory testing. Silt and fine sand strata with little cohesion should be investigated using mud rotary techniques to prevent disturbance. General strength characterization by soil layer should be used for analysis of trench wall stability."

Jan 1, 2006

By Mark Koelling

This paper presents a case history of a ground improvement program conducted in a soft soil environment and seismically active region in the northwest corner of Washington State near the Canadian border. The program was performed over several years, and provided adequate soil bearing conditions for the construction of several structures. Completed development includes separate construction of four adjacent structures, each with unique total and differential settlement requirements and built at approximate two year intervals. Site soils consist of 45 feet of loose saturated sand and silt overlying 70 feet of very soft to stiff (N60 = 0 to 7) normally consolidated clay. Adding to the complexity of the site is the owner?s requirement that all existing structures remain open and in service during construction of each subsequent structure. The paper presents the site geotechnical information and the foundation design issues. Details of a combination of ground improvement methods is presented, including stone columns, wick drains, a preload surcharge, and staged construction to provide soil support for shallow foundation construction of all structures at this site. The soil test results and settlement observations are presented along with QA/QC measures. Lastly, a brief method sustainability comment will be made.

Jan 1, 2010

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

The city of Naruto in the southwestern part of Japan is situated at the mouth of the mighty Yoshino River. An approximately 1,000m-long levee/bulkhead along one of the river’s tributaries in the city was raised with prefabricated steel panel walls on a concrete base bulkhead. Some sections of the walls’ foundations were combi-walls made of sheet pile cut-off walls and interspaced pipe piles; both of which were installed with press-in piling because the new wall alignment was very close to existing homes and businesses. A Clamp Crane, which clamped onto already installed piles and moved forward and backward on them, was utilized for a segment where the access to its piling location was too tight for a conventional crane or a track-mounted pile driver to maneuver.

Sep 8, 2021

By Jamey B. Rosen

As Project Information Management Systems (PIMS) technologies develop, the range of projects to which one can apply these technologies grows while the cost to apply them shrinks. In recent years, technologies previously limited to large “megaprojects” (e.g., major dam rehabilitations) owned by major entities (e.g., the United States Army Corps of Engineers) with large budgets have been applied to smaller projects with less stringent specifications and more modest budgets. This paper will describe applications of PIMS technologies to small projects with limited budgets, including examples from levee construction, small-scale grout curtain installation, and diaphragm and secant pile cut-off walls. We will include a demonstration of how PIMS technologies can effectively analyze verticality data from koden and hydromill data streams to automatically generate models and as-built drawings showing overlap and deviation along the depth of the foundation. INTRODUCTION This paper discusses the application of Project Information Management Systems (PIMS) technologies to geo-foundations projects, with a focus on technologies and examples that are in a lower cost range. PIMS technologies allow contractors and other stakeholders to perform efficient quality control on their data, generate quick or automatic reports and as-built drawings, perform analyses to better understand their construction, and ultimately use their data to increase the quality of their construction. As PIMS technologies are relatively new to the deep foundations industry, and owner specifications on their use are generally viewed as complex and limited to large scale projects, PIMS technologies are frequently viewed as an expensive component that is beyond the scope of a smaller or simpler project. However, the same principles and techniques generally associated with large projects can be applied to projects at smaller scale. Furthermore, as these technologies develop both in the deep foundations and other industries, the cost of application is decreasing quickly making them even more affordable for smaller projects. The remainder of this paper provides some justification for applying PIMS technologies, describes some scalable data management concepts and workflows and then provides some examples of “low cost” applications of these technologies.

Jan 1, 2019

By Chris Harnan, Christophe Justino

The European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute (DFI) jointly published Edition 1 of the ‘EFFC/DFI Guide to Support Fluids for Deep Foundations’ in April 2019. This Guide was prepared by a Task Group comprising experts on deep foundations from contractors, materials suppliers, consultants and academics. The Guide builds on work carried out by the Tremie Concrete Guide Task Group and presented in Edition 2 of the Tremie Guide. The Paper discusses and describes the content of the Support Fluids Guide which presents the state of the art on support fluid management, as well as the R&D work currently being carried out and funded by EFFC and DFI sponsors through an ongoing Field Research Study (FRS) as well as a review of academic research linked to the EFFC/DFI joint effort aimed at improving knowledge and guidance on support fluids. The FRS and academic research will help to improve the understanding of relevant support fluid properties including stability of excavations, interface layer formation, effect of filter cake and the development of new sampling and testing methodology. The Paper also presents the initial findings from the FRS program as well as a discussion on the challenging aspects of support fluid management with emphasis on design, performance, testing, and the environment.

May 1, 2022

By Mario Mauro, Jeff Taylor, Carlos Morales

"In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria.For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.INTRODUCTIONProject LocationThe Herbert Hoover Dike (HHD) system, around Lake Okeechobee in South Florida, consists of a series of levees, culverts and locks and is approximately 143 miles long (Figure 1).Lake Okeechobee is the second largest freshwater lake in the lower 48 states of the United States. The lake is the primary drinking water source for numerous communities around the lake and to millions of people living along the lower east coast. The lake is also a vital source of irrigation for the agricultural industry in the South Florida region.Lake Okeechobee is 33 miles wide from north to south and 30 miles wide from east to west and has a surface area of 730 square miles. The average water depth of the lake is 9 ft."

Jan 1, 2017

By Mario Mauro

In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria. For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.

By Richard Berry

The spacing of grout injections is typically about 2 to 2 V½ meters if the purpose of the grouting is densification of the in-situ soils. Hole spacing will vary with the in-situ soil properties and the grout injection rate; faster rates requiring closer hole spacing.

Feb 10, 2003

By Michael Hughes, Selva Selvamohan, Ray Costa

"Cutoff walls are commonly used to mitigate underseepage problems for levee remediation projects. At abrupt changes in seepage cutoff wall depths there is a potential for water to flow around the back of the deeper cutoff wall leading to elevated seepage pressures on the landside that could result in exit gradients exceeding design criteria. This condition is referred to as end-around-effects and is a complex problem that requires detailed and time consuming 3-D numerical modeling to represent accurately. This paper presents a simple approach for assessing end-around-effects using the results of 2- D seepage analysis to determine if lateral extension of the deeper portion of the cutoff wall is required. This simplified approach provides a pragmatic solution to a complex 3-D problem. The presented procedure was used as part of the Feather River West Levee Project in Yuba City, California, to assess end-around-effects at 26 locations. The results showed that wall extensions of up to 100 feet were needed at only 2 locations.INTRODUCTIONAs the lead geotechnical consultant for the Feather River West Levee Project, AECOM were responsible for designing levee remediation works for approximately 35 miles of levee protecting the area around Yuba City, California, and communities to the north and south. Due to land use constraints, seepage cutoff walls were the main remediation alternative selected to address underseepage issues for the project.As part of the design review process, the California Department of Water Resources (DWR) requested AECOM to look at 26 locations along the levee alignment where the depth of cutoff wall changed abruptly from shallow to deep, or vice versa. At these locations there was the potential for seepage pressures to pass behind the deeper section of cutoff wall and stress the blanket layer landward of the cutoff wall. A condition referred to as end-around-effects.End-around-effects involve complex 3-D ground conditions that have traditionally been addressed by laterally extending the deeper section of cutoff wall an arbitrary distance based solely on engineering judgment. In discussions with DWR, AECOM developed a simple procedure to provide a more objective assessment of end-around-effects without the need for detailed and time consuming analysis. This procedure allows the engineer to make an informed decision of whether end-around-effects are a problem at the location of a cutoff wall transition rather than laterally extending the deeper section of cutoff wall an arbitrary distance based on engineering judgment alone."

Jan 1, 2015

By Ricardo Dobry, Alain Pecker, George E. Leventis, Ralph B. Peck

"This year’s DFI Outstanding Project Award is for the design and construction of the foundation scheme for the largest cable-stayed bridge in the world. In 1993, Gefyra, SA (a French/Greek consortium led by VINCI of Paris, France) was awarded a €750 million ($1billion+ USD) Concession Contract to design, build, fi nance, operate and maintain a three-span cable-stayed suspension bridge connecting the Peloponnese, Greece’s southernmost peninsula, with the mainland across the Gulf of Corinth. The contract extends over a 42-year period, 7 years for design and construction and 35 years for operation. The project was fi nanced through a combination of public funds, private equity and bank loans. Alternative foundation concepts that were considered included traditional driven piles, deeply embedded caissons and soil improvement. PROJECT CHALLENGESThe extreme technical challenges faced included:??Weak foundation soils composed of soft alluvial deposits consisting of interbedded layers of granular and cohesive materials with thin layers and lenses of gravel and liquefi able sand pockets; rock is believed to be at a depth of 1,000 m (3,500 ft) or more.??A very deep seabed exceeding 60 m (200 ft).??The requirement to withstand the collision of 180,000-ton tankers traveling at 16 knots.??Maximum wind forces of 250 km/hour (155 mi/hour).??Design seismic forces corresponding to Richter magnitudes of 7.0+ with peak ground accelerations of 0.48 g at seabed.??Design tectonic movements of 2 m (7 ft) in any direction between any two adjacent bridge pier foundations/pylons.Considering subsurface conditions and local seismicity and water depths, foundation design and construction methods were the key drivers for this project. In large part, the success of the project is owed to the unprecedented partnering and collaboration between all partners involved fostered under the leadership of Jean Paul Teyssandier and Gilles De Maublanc of VINCI Group (France) who served as lead Concessionaire and General Contractor. The joint venture’s lead Greek partners were Elliniki Technodomiki/AKTOR and J&P/AVAX. Alain Pecker of Geodynamique et Structure (France) served as lead Geotechnical Consultant/ Designer while Buckland and Taylor (Canada) served as Design Checkers with Ralph Peck and Ricardo Dobry (U.S.) as Special Advisors on foundation issues, Langan International/Langan Engineering and Environmental Services P.C. (George E. Leventis, Gregory Biesiadecki and Diane Fiorelli) served as Technical Advisor on geotechnical, geodynamic and foundation/marine construction issues."

Jan 1, 2007

By Brian M. Fraley

"Portions of the Catholic Total Abstinence Fountain in Fairmount Park in Philadelphia, Pa., were in “imminent danger,” according to a restoration services request for proposals (RFP) issued by the City of Philadelphia in August 2014. Open voids in the subsurface beneath the foundation were causing ongoing settlement of the fountain.The fountain was unveiled in 1876 as an ornamental drinking fountain for the Centennial International Exhibition, which celebrated the signing of the Declaration of Independence. Its creation was commissioned by the Catholic Total Abstinence Union of America, an Irish temperance organization that advocated for total abstinence from alcohol. Ironically, the fountain ran dry decades ago.The now-defunct fountain features a 100 ft (30.5 m) wide granite base with three steps in the shape of a Maltese cross. The centerpiece — enclosed by a 40 ft (12.2 m) diameter basin — is a 15 ft (4.6 m) tall statue of Moses perched atop an iglooshaped marble mound. Four subsidiary statues rise from granite pedestals at the tips of each arm of the cross, including Archbishop John Carroll, Charles Carroll of Carrollton, Father Theobald Mathew and Commodore John Barry.Natural and Man-Made DamageThe City of Philadelphia’s RFP called attention to three “high priority structural areas.” It was noted that Moses, Father Mathew and the steps surrounding the fountain had been documented as public hazards. The long-term effects of water infiltration had set in, eroding mortar joints and causing some stones to jut out. Furthermore, the stone base supporting the 16 ton (14.5 tonne) statue of Moses was in danger of collapsing. The statue of Father Mathew had been struck by lightning in 1910 and was repaired with an iron and metal pin anchor system, which had succumbed to corrosion. The city considered the statue of Father Mathew as the most threatened of the statues. Mike Miluski, P.E., vice president of Compaction Grouting Services (CGS), recalled “the fountain was in pretty bad shape” as he walked onto the site in August 2016 and immediately recognized the challenges ahead."

Jan 1, 2017