Search Documents

By Mousaab Majar, Nikolaus Schneider

The technical challenges for accurate drilling positions increase with deep underground structures in inner city areas. Designed for jet grouting, specific sensors have been developed to record the alignment of rods during drilling by integrating microchips into the drilling rods. By feeding the rod with constant electric current, microchips, integrated in special couplings, can be read during the drilling process and tracked on monitors installed in the operator’s cockpit. The orientation for the drilling rod is provided by magnetic points and a compass, positioned above ground on the drilling rig. In combination with asymmetric drilling bits, it is now possible to steer the drilling hole to predetermined positions to compensate for deviations in deep bores. This type of drilling rod for jet grouting has been used in Berlin since summer 2019.

May 1, 2022

By Scott Dodds

"The Oxford Hydroelectric Station was a unique project that incorporated a variety of dam strengthening methods to stabilize the facility in order to meet the standards required by Federal Energy Regulatory Commission (FERC). The dam stability and Probable Maximum Flood (PMF) remediation work consisted of (1) construction of a new emergency spillway; (2) installation of 75 high capacity rock anchors; (3) construction of an anchored concrete powerhouse buttress; (4) construction of cast-in-place and sheetpile flood walls; and (5) design and construction of a permanent soil nail wall. INTRODUCTIONThe Oxford Hydroelectric Station is one of 11 hydroelectric facilities owned and operated by Duke Power along the Catawba/Wateree River. The Catawba River originates in the foothills of the Appalachian Mountains just west of Morganton, North Carolina. The river flows east out of the mountains and, at a point just below the Oxford Dam, the Catawba River turns and heads southeast. The Catawba River continues to flow southeast past Charlotte and into South Carolina where it eventually becomes the Wateree River. The Wateree River eventually flows in to the Atlantic Ocean.Located a few miles east of Hickory, North Carolina, the Oxford Dam and Hydroelectric facility is in the upper reach of the Catawba River. Oxford Dam creates the third impoundment along the river known as Lake Hickory. Lake Hickory is well known locally for providing many outdoor activities such as boating, jet skiing, canoeing and fishing. The dam and powerhouse were put into operation in the spring of 1928.Key features of the dam include a short embankment section on the south end of the structure, a 391-foot (119m) long south bulkhead and powerhouse, 540-foot (165m) long gated spillway section and a 235-foot (71.6m) long north bulkhead. The maximum height of the dam is approximately 100-feet (30m) from the crest to the dam/rock interface. (See Figure 1).The work associated with this project is the result of licensing requirements of the Federal Energy Regulatory Commission (FERC) which mandates that all hydroelectric facilities have the capacity to safely discharge runoff created by a critical rainfall event defined as the probable maximum flood (PMF). Duke Power, a division of Duke Energy (DUKE) submitted an initial PMF report in 1992 which indicated that at the Oxford Dam would be overtopped by approximately 10-feet of water during the modeled PMF event. Given the duration and depth of the overtopping, significant damage to the facility and a possible breach could result. Therefore, modifications to the existing facility were necessary to satisfy the report of the PMF model."

Jan 1, 2005

By Terrence R. Udland, Russell D. Call

"Honored with a DFI 2006 Special Recognition Award, the Four Bears Bridge was constructed across Lake Sakakawea and opened to traffi c in September 2005. The very large lake size and severe winter conditions required an effi cient foundation design capable of resisting extreme ice loading and able to be effi ciently constructed in waters up to 90' deep (27.4m).DESIGNING FOR EFFICIENCYLocated in a remote area of North Dakota, the Four Bears Bridge replacement was a major undertaking for the North Dakota Department of Transportation, with dual goals of providing a new structure that would endure a severe environment, while enhancing the natural beauty of the area. Competing bids would achieve the best price for the owner, challenging the design team to creatively solve the engineering challenges unique to the site. Foundations for North Dakota’s new Four Bears Bridge had to accommodate water level fl uctuations of up to 40 feet (12m), along with extreme ice loading and be effi cient in order to be the low cost solution at the time of bidding. All three major criteria were achieved through the use of an effi cient ‘fl oating’ lost precast concrete cofferdam founded on steel pipe piles, which allowed the contractor to achieve the project schedule. The result is an award-winning bridge that is contextually sensitive to the environment. The bridge aesthetics pay tribute to the Three Affi liated Tribes, the Mandan, Arikara and Hidatsa, who reside on the Fort Berthold Indian Reservation, adjacent to the bridge site.The original Four Bears Bridge was located over the Missouri River near Elbowoods, the native grounds of the Three Affi liated Tribes. Construction of the Garrison Dam in the early 1950’s created Lake Sakakawea, a fl ood control project on the Missouri River, and resulted in the area being fl ooded. The bridge, along with many tribal members, was relocated to a site near New Town. The bridge provides the primary crossing of Lake Sakakawea and is a critically important transportation element for the residents of the Fort Berthold Indian Reservation. The relocated bridge had become functionally obsolete and not replacing it would require a detour of 170 miles (274km). The North Dakota Department of Transportation determined that it should be replaced. In order to achieve the most effective solution, the North Dakota Department of Transportation selected a design team responsible for the creation of competing steel and concrete designs that were competitively bid. The design team was led by Kadrmas Lee & Jackson, with FIGG responsible for the concrete bridge design, while Lichtenstein Consulting and Kadrmas Lee & Jackson completed the alternate steel bridge design."

Jan 1, 2007

By Patrick van der Schaaf

"During 2016, foundation piling works were completed to allow for the construction of a production and storage/handling terminal in Rotterdam. It is there that steel foundations will be produced for offshore wind farms and the oil and gas industry. Several Dutch contracting companies were involved in constructing: foundations for an assembly hall, a barge quay and a deep-sea quay wall. For the hall foundations, cast in situ concrete vibro piles were created. Open ended steel casing piles were also installed due to very high cone resistances which made it impossible to perform cast in situ piles in certain areas. The quay wall was constructed with open ended steel casing piles in combination with sheet piles. A deep-sea quay wall was also constructed to provide enough storage area for the offshore mono piles. This project was unique and challenging due to the use of different foundation technologies in challenging circumstances and soil conditions. This paper will give an insight into the Dutch use of varying foundation piling techniques for deep-sea quay wall constructions. It can be concluded that even experienced local contractors can be surprised by variations in soil conditions. It will also show how the contractors adapted to the difficult circumstances.PROJECT OUTLINEThe project consisted of a barge quay near the assembly hall with a length of 500 metres, width of 42 metres and a height of 35 metres, and a deep-sea quay wall 480 metres in length. This paper concentrates on the foundation works for the construction of the deep-sea quay wall. The construction of the deep-sea quay wall consisted of a combination of open ended steel casing piles with a diameter of Ø 1420 mm and a wall thickness varying between 21 and 23 mm. The lengths of the steel casing piles varied between 32 and 37 metres. Between the steel casing piles triple PU 28 sheet piles were installed with lengths varying between 26 and 29 metres. In the Netherlands, a combination of open ended steel piles and sheet piles is known as a “combi wall”. For the deep-sea quay wall a steel combi wall was shored with steel H- section profiles that were driven in a raked position whilst being injected with grout, so called MV-piles. The MV piles for this project consisted of steel HEB 600 sections with lengths from 52 up to 59 metres and were installed with angles varying between 42.5 and 47.5 degrees. For a detailed overview regarding the project specifications reference is made to table 1 which is presented below."

Jan 1, 1900

By Soorkty Elarabi

The aim of this paper is to discuss the impact of end bearing plate on the capacity of micropile. Preliminary studies have been made in Sudan in specific area of cohesive soil. Experimental works were carried on a number of micropiles with and without end bearing plate. Same diameters, lengths and techniques of placing cement grout are considered, there after the axial load test applied to find out the capacities of micropiles in both cases. Deduced results in each case show that the end bearing plate has no positive impact on micropile capacity.

Oct 1, 2022

By Ramanathan C, Prasad P. V. S. R

The most critical challenge for any large size storage structures to be constructed on soft compressible soils is bearing capacity and consolidation settlements. Consolidation is the time dependent phenomena, as expulsion of water from soil voids on application of external load will take longer period. It is mainly influenced by soil consistency, permeability, thickness of compressible stratum and presence of free draining layers. This study deals with the foundation solution of a large size Mounded Storage Vessel (MSV) to be constructed on thick compressible stratum whose loading intensity is around 155 kPa and the estimated settlements are greater than 400 mm. Hence, the foundation solution using vibro stone columns is adopted as an effective technique to address the challenges of excess settlements and inadequate bearing capacity. Further to keep settlements within the permissible limit of 50 mm, preloading technique with 60% of actual loading intensity will be utilized. The consolidation analysis of stone column reinforced foundations is carried based on the method given by Han and Ye (2001). The quality of the stone columns is ensured by real time quality control measures and the performance of the stone columns shall be ensured by vertical load tests. Ground settlements was closely monitored with proper instrumentations and the actual degree of consolidation has been verified by Asaoka’s (1978) method.

Sep 1, 2022

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

The Sandbukta-Moss-Såstad (SMS) project is a part of the Intercity development project, which is part of the largest transport project in Norway, consisting of 270 km of new double-track rail. The SMS project consists of 10km of double-track railway including three open stretches and two tunnels. Soil conditions consist of quick clay underlain by Bedrock. Dry soil mixing (DSM) was considered as the main soil improvement method to allow for excavation of the quick clay and construction of the D-Wall panels. The preliminary design revealed around 25,000 ton of binder installation. Therefore, a test field has been conducted to evaluate binder alternatives in means of improved soil strength by considering CO2 emissions. Multicem and Standard cement (Standard FA) have been compared for that purpose. Multicem is a type of binder which mainly consists of Portland cement and cement kiln dust (CKD). CKD is a fined-grained, solid, highly alkaline material removed from the cement kiln exhaust gases. reverse column penetration test (FOPS) and pre-drilled column penetration test (FKPS), which are common tests to evaluate DSM strength have revealed comparable strength outcome for both binder types. Therefore, Multicem has been selected as the main binder type to be used further which provided a reduction in CO2 footprint of up to 40%.

May 1, 2022

By Prodyot Kumar Ray, Sudip Kumar Koley, Aminul Islam, Somnath Banerjee

One of the most important topics in the construction industry is the building of railway embankments. Being such a delicate and significant structure, it is crucial to properly design the embankment and build it while adhering to all statutory criteria and design guidelines. A railway embankment's subsoil condition and fill material, groundwater table, dynamic and static loads during operation, and embankment geometry are some of its most crucial design considerations. This paper discusses the likely causes of the collapse of a railway embankment in eastern India as well as the suggested rehabilitation scheme. It was observed that an embankment collapsed in the aforementioned area during a inccesent rain. Along with the side shifting of a cantilever retaining wall that was positioned at the bottom of the embankment, the embankment next to the railroad track settled vertically. According to the available geotechnical report, the sub soil strata in half of the area adjacent to the embankment profile, where the embankment height gradually decreases from maximum height, is stiff to hard clay with an undrained cohesion value of around 50 kpa followed by dense sand, and the sub soil strata in the other half is soft clay with an undrained strength of 15 kpa. As a result, in the rainy season due to the sudden increase in the water table, the self-weight of the embankment increased and further caused the under-laying soft clay to get squeezed away and settle. Due to this squeeze/settlement effect of the soft clay layer, the retaining wall got disturbed along with the generation of an undulated embankment top profile. As a remedial measure, it is proposed to construct a contiguous bored pile wall at the toe of the embankment to stabilize the slope, and additionally, compaction grouting is recommended beneath the embankment to improve the soft clay. In order to carry out the analysis, certain commercial geotechnical software like Slide, Wallap, and Plaxis 2D are used. The factor of safety of the embankment slope considering the above restoration scheme is adequate under static and seismic conditions.

Sep 1, 2022

By P. K. Ray, Sudip Kumar Koley, Sainath M. Reddy, Devulapalli L. S Rasagna

Bangalore Metro Rail Project- phase II is one of the technological challenging project, particularly construction of underground metro rail system. The Bengaluru city is very congested area and connecting metro rail system with existing transportation networks is equally challenging. In this phase-II, the Underground metro is being constructed by blasting hard rock formation and supporting the shear zone. Most of the subsurface rock formations comprise of granitic Gneissic formations are of Precambrian age and shear zones that includes friable a thin weathered rock formation. With such subsurface geological conditions, , the anticipated construction challenges include : A) deep excavation of hard rock mass under old and sensitive structures and buildings, by controlled blasting; B) variation in the rock grade from grade I to grade V; C) weak rock mass at shear zone resulted in planar failure beneath the retaining wall; D) water seepage along shear planes; E) selection of a suitable method to conducted blasting near high voltage electrical machinery or power cables. This paper describes the methods adopted to mitigate these technological challenges and to meet stringent environmental compliances. These includes study and application of various geological, geotechnical parameters to develop a proper line drilling and controlled blasting techniques to minimize the ground vibrations and controlling the rock fragmentation and to optimize the equipment performance in terms of productivity and time schedules. The “Phase 2” software of “Rocscience” has been used and Regression analysis has been carried out by using MCD (Maximum Charge per Delay) and PPV (Peak Particle Velocity) to estimate with FOS (Factor of safety) for sensitive places such as nearby high rise buildings and electrical transformers.re.

Sep 1, 2022

By Lawrence F. Johnsen, Felix Ferrer, Dino Tomasetti, Cassandra A. Wetzel

"A 17 story building was constructed at the Brooklyn Navy Yard on a site with a long history of development. Most recently the site supported a dewatering well and craneway to service two adjacent drydocks. The subsurface conditions generally consist of the following strata and approximate depths: miscellaneous fill and debris to 20 ft., organic soils to 35 ft., liquefiable sand to 45 ft., varved clay to 65 ft., glacial till to 95 ft. and gneiss bedrock.Hollow core bar piles replaced 18 in. diameter caissons on a 1.67:1 basis. The resulting service loads on the hollow bar piles were 600 kips compression, 21 kips lateral, 180 kips tension and 450 inch-kips moment. The top 30 feet of the hollow bar was cased with a 16 in. x 0.375 in. Grade 50 steel pipe. The piles were socketed 6 feet into bedrock. An extensive load testing program confirmed the axial and lateral load capacities. The paper will also discuss some adjustments to the installation procedure based on the load test program.PROJECTThe hollow bar piles were installed to support a 95,000 sf footprint, 17-story office building at the Brooklyn Navy Yard. The Brooklyn Navy Yard was first developed in the late 1700’s to build merchant vessels. The federal government purchased the old docks and adjoining 40 acres in 1801. The site was an active U. S. Naval Shipyard from 1806 to its decommissioning in 1966. At its peak in World War II it employed 70,000 people, 24 hours a day. Since 1966 the property has been converted to private manufacturing and commercial activity.The site is located between Dry Docks 2 and 3. The adjacent drydocks extend 40 to 43 feet below grade. The drydock walls are restrained by tierods extending back to deadman anchors. The site is also underlain by piles that were installed to support rail lines and a craneway. The building footprint also covered an 85 ft. wide, 70 ft. deep dewatering well which had a thick slab. The structural engineer for the project, ARUP, designed the building to span over the dewatering well.SUBSURFACE CONDITIONSIn September 2014, Langan Engineering conducted a geotechnical engineering study for the project. Figure 1 provides a subsurface profile through the long axis of the site. The general soil profile was very erratic but generally consisted of miscellaneous fill and debris to 20 ft., organic soils to 35 ft., liquefiable sand to 45 ft., varved clay to 65 ft., glacial till to 95 ft. and gneiss bedrock. The fill contained numerous obstructions from the over 200 years of site development. The organic soils were mostly very weak and compressible organic silt. The depths and thicknesses of the varved clay, and sand varied"

Jan 1, 2017

By Matt Fenwick, Douglas R. Schwarm

Stringent underwater noise limits at the Fairview Ave. N. bridge replacement on Seattle's Lake Union required an innovative approach to supporting the 470-ft long drill trestle. Screw-in foundations would reliably mitigate noise, but the required 500-kip bearing resistance were an order of magnitude higher than typical helical piles. This paper describes the process of designing, installing, monitoring, and testing 22-inch dia. helical piles 80 feet long with 36- and 42-inch dia. helices. A static load test confirmed that the conventional k-factor design method can be extended to capacities of up to 800 kips. A 375 ft-kip drive mechanism had to be fabricated because no North American equipment could supply the necessary installation torque. Real time installation monitoring and later "re-torque" tests confirm that helical piles gain capacity with time, analogous to driven piles under restrike. Underwater and on-land measurements confirmed very low noise, suggesting the possibility of widespread adoption where similar limits are imposed. Overall, this case history illuminates the need for innovative deep foundation types in response to ever-increasing regulatory constraints.

Sep 8, 2021

By Maurizio Siepi, Bruno Vingiani, Claudio Asioli

"The article describes an emergency rehabilitation intervention executed at Buyo Dam, in Ivory Coast, to intercept a significant water seepage occurring through the foundation of this zoned earthfill retaining structure constructed in the late Seventies. To solve the problem, a 800 mm thick, 400 m long impervious cut-off wall (COW) was constructed on the right side of the embankment, operating from the dam crest and with the reservoir almost at its maximum level. The use of an innovative pre-mixed self-hardening grout, with a target hydraulic conductivity coefficient (k) lower than 10-9 m/s, was considered the only way to match the tight working schedule and the strict requirements for the filling material of the COW.Presentation of the Hydroelectric Scheme of BuyoThe hydroelectric scheme of Buyo, located at 6°14’28” N 7°20’45 W on the Sassandra River, in Ivory Coast (Figure 1), was built in the late Seventies for agriculture and power generation. With a reservoir of 8.3 billion m3 and an installed power capacity of 165 MW, enough to supply electricity to 111,000 homes, it represents an installation of great significance for this West African country."

Jan 1, 2016

By Chang-Yu Ou, Shao-Chi Chien, Hsuan-Hsiang Chang

"A field test was performed to investigate the applicability of electroosmosis with the injection of saline solution of Taipei silty clay. The calcium chloride solution and sodium silicate solution were used as the saline solution for the injection in this test. The results of this study indicate that injection using calcium chloride solution and sodium silicate solution during the electroosmosis to increase drained water from cathode and electro-chemical reaction can greatly improve the effect of electroosmosis and shorten the time of treatment. The results of field vane tests showed that the undrained shear strength after treatment increased an average of approximately 120% for a treatment period of 24 days.INTRODUCTIONThe first field application of electroosmosis in soil was demonstrated by Casagrande in 1939. Since then, more complete field applications of electroosmosis such as Bjerrum (1967), Fetzer (1967), and Lo et al. (1991b) have been made.The results of field electroosmotic work for a period of 120 days were presented by Bjerrum et al. ( 1967). The mean undrained shear strength, Su, increased from 18 to about 40 kPa, with a uniform surface settlement of about 0.5 m. Lo et al. (1991b), with a more sophisticated installation and a relatively larger spacing, also had positive results. For a 3 m electrode spacing during the treatment of a period of 33 days, the mean Su increased from 18 to about 25 kPa. Although the effect of the electroosmosis could be applied in the field based on the above examples, the response remained slow. For actual field work, the application of electroosmosis will be limited due to short project schedules and request of the effect of improvement."

Jan 1, 2005

By Nabil F. Ismael, Khalid Farraj

"The axial load transfer along large diameter bored piles in very dense silty sand was examined by field tests. Two instrumented piles 1.2 m diameter and with embedded length of 18 m and 25 m were load tested in axial compression to failure in connection with the construction of a big tower building in Kuwait City, Kuwait. Instrumentation included vibrating wire strain gages at various levels, displacement transducers and extensometers. The purpose being to measure the axial load distribution, skin friction, and base resistance at various load levels. In addition the settlement of the piles and the elastic compression were monitored. The ultimate pile capacity, side friction, and base resistance were determined and correlated with the Standard Penetration Resistance values as determined from the boreholes. Most of the load was transferred as side friction and the pile settlements at the maximum loads ranged from 1.6% to 2.2% of the pile diameter.INTRODUCTIONLarge diameter bored piles are used with increasing frequency for heavy structures in Kuwait and the Gulf region in calcareous sand. The behavior of short piles ranging in depth from 8 m to 15 m was examined by field test (Ismael 2012). However, larger diameter and deeper piles are being used more frequently, including the project described in this paper which included piles with 1.2 m diameter and 18 m to 25 m depth. The design of these piles requires knowledge of the skin friction and point resistance in these soils. While field tests on driven piles are available (Ismael 1989, Ismael 1999), field test data on long large diameter piles installed through very dense sands or silty sands are very limited at present. The results of two load tests carried out recently on instrumented bored piles at one site in downtown Kuwait City have become available. In these tests the failure load was extrapolated from the test results. It is important to examine and analyze the test results for the benefit of the geotechnical research and design engineers."

Jan 1, 2017

By Vince Luongo

"INTRODUCTIONThe West Side Combined Sewer Overflow (CSO) Tunnel Project is located in Portland, Oregon and is part of the Willamette River CSO Control Project. The purpose of the West Side CSO Project is to reduce the frequency and volume of combined sewage overflows from the drainage areas on the west side of the Willamette River using the West Side CSO tunnel as a combined storage and conveyance facility. The sewage is then directed to the Pump Station on Swan Island, which is located on the east side of the Willamette River. From here the combined sewage is pumped through force mains that discharge into the existing Peninsular and Portsmouth tunnels.The West Side CSO tunnel has an inside diameter of 14-feet (4.27m) and is approximately 18,150-feet (5,532m) long. The tunnel slopes at a constant down gradient of 0.0018 from south to north over the entire length of its alignment.The tunnel passes beneath six existing bridges; Hawthorne Bridge, Morrison Bridge, Burnside Bridge, Steel Bridge, Broadway Bridge and Fremont Bridge. The general tunnel alignment follows beneath the Naito Parkway starting at Clay Street Shaft and connecting three other shafts on the west side of the Willamette River, Ankeny Shaft, Upshur Shaft and Nicolai Shaft. It then passes below the Willamette River and on to Swan Island to connect with the Confluent Shaft, which will combine flows from the West Side CSO and East Side CSO (not part of this contract) and then continues to the Pump Station Shaft.The Nicolai Shaft is the primary mining shaft from which two TBM’s were launched to construct the West Side CSO tunnel. The first TBM started mining south and terminated at the Clay Street Shaft. The second TBM started mining north below the Willamette River and terminated at the Swan Island Pump Station Shaft."

Jan 1, 2006

By Dennis Nottingham

"Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers’ experiments, observations and measurements, led to an “H” pile probe design which has produced measured soil density improvements up to 250% using SPT “N60” values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern “Open Cell” bulkhead projects will be presented and discussed.INTRODUCTIONNecessity often is the basis for innovation and such was the case for needed cost-effective deep soil fill compaction in Open Cell bulkheads where granular fill below water levels was often placed.Open Cell bulkheads were developed by PND Incorporated starting in 1980, for the express purpose of meeting client demands for an economical, easily constructed, extremely strong structure. Earth-filled structures historically have had a long history of problems with stability, scour and settlement.Open Cells are flexible steel sheet pile membranes supported by soil contact with embedded tail anchor walls.This concept creates an integral reinforced soil system. The result is a structure that can withstand large settlement and support a variety of very large loads. In effect, viewed from above the structure becomes a series of U-shaped horizontal membranes that require no toe embedment for stability. The Open Cell bulkhead is constructed of only three components: flat sheet piles, fabricated connector wyes and anchor piles. Compared to alternative structures, several cost savings are realized from this land based construction such as, reduced sheet pile area, greater construction tolerance, minimal pile penetration, and simplified backfilling procedures. In seismic regions or weak soils, the tail walls can be extended as required to guarantee fill mass stability."

Jan 1, 2005

By Piotr Kozlowski, Stanley L. Worst, Matthew J. Niermann

Circular secant pile shafts were installed along the tunnel alignments for both the Ohio Canal Interceptor Tunnel project in Akron, Ohio and the Ohio River Tunnel project in Louisville, Kentucky. The diameters ranged from 34 to 51 feet and the depths ranged from 49 to 107 feet. Verticality and concrete volumes were measured on all piles to verify compliance with the design, which for some shafts consisted of a finite element model with multiple openings using unreinforced concrete secant piles. All secant piles were drilled into rock to seal off the groundwater. This paper will discuss the design, construction and quality control of the secant piles for these projects. INTRODUCTION Many Midwest and Northeast cities have Combined Sewer Overflow (CSO) systems which discharge pollutants into waterways during wet weather events. One way to remedy this issue is to provide a temporary overflow tunnel. A temporary overflow tunnel connects to the combined sewer system and collects the overflow during wet weather events, storing the wastewater until the event has subsided. After the storm event, the stored wastewater can be pumped to the treatment facilities and processed as normal. Project Background – Akron, OH The Ohio Canal Interceptor Tunnel (OCIT) project was performed as a result of the Environmental Protection Agency’s (EPA) Consent Decree with the City of Akron, Ohio. This Consent Decree required modification of the existing Combined Sewer Overflow system. The resulting project consisted of a 27- foot diameter tunnel with multiple points of entry to capture the sewer overflow and prevent it from entering waterways. The tunnel is over 6,000 feet long and is as deep as 150 feet below the ground surface; see Figure 1 below.

Jan 1, 2019

By Stefan Schwank, Alexander Blatt, Franz-Werner Gerressen

Diaphragm wall technique is usually used to install diaphragm walls, which are known as underground structural elements commonly used for retention systems and permanent foundation elements as well as deep groundwater barriers, named Cut-Off-Walls (COW). In this exploration project, the diaphragm wall equipment was used in the 2019 summer season to perform the first part of an exploration and bulk sampling program for a potential mine on the Star Kimberlite. Beside the idea of using the diaphragm wall technique as bulk sampling equipment, the sampling program required the adaption of equipment and tools for a depth capability never reached before by a trench cutter in any commercial application worldwide. The paper will explain the development of the sampling program as well as the challenges occurred with the local geology and the specific demands of the exploration and sampling program. It will also provide an overview of the lessons learned during the 2019 season and will give an outlook to the approaches of optimization for the second phase which will be carried out in 2020.

By Andhra Pradesh, Nagarajkumar B. V

As a part of Mumbai City Mega Drinking Water Project at Amar Mahal Tunnel-1 Ghatkopar East Mumbai, drinking water tunnels were proposed by MCGM from Amar Mahal to Trombay reservoirs, Amar Mahal to Wadala and further up to Parel. The pipeline has to be underground and laid at a depth of 5.5m. The initial proposal was to provide sheet piling to enable the safe excavation and installation of underground pipeline. However, installation of sheetpiles was practically not feasible due to the existing soil strata for driving the sheet piles. Hence, it was proposed to install micropiles instead of sheet piles. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with temporary struts for shoring protection works in this project.

Sep 1, 2022

By Michael Arnold, Jignyash Manyam, Yoav Rappaport

The USACE required construction of over 13 miles of cutoff wall at an average depth of 65 feet for the Herbert Hoover Dike (HHD). To meet project requirements, to provide quality control and make sound operational decisions, automated data capture, retention and visualization is crucial. Accurate and complete data management allows the authors to deliver critical business insights and to improve operational efficiencies. The author’s understood the necessity of capturing all their data, and efficiently processing and displaying it for multiple stake holders, for both internal and external purposes. The authors realized early in the project life cycle that data ownership and management is one of the fundamental features of the construction process. The authors developed their own software and use two in house applications; WEB-BGM online portal and, b-project which store rig production information combined with field quality control. b-project is used to create and deliver the Enterprise Database (EDB) to the USACE. Another biproduct of capturing the production data is the generation of the Geographic Information Systems (GIS) and also business analytics visual interactive display, developed through Microsoft Power BI. The paper focuses on the business process workflow and various technologies employed and lessons learned from the field operator perspective to achieve higher returns on business software operations.

Oct 1, 2022