Search Documents

By James E. Parkes

The Silver Spring Transit Center is a new three-level transit center that will include bus loops for County, Metro and intercity buses, parking, and retail space. It replaces an existing bus station and connects to a busy metro rail station in downtown Silver Spring, Maryland. Significant site constraints in both plan and profile had to be dealt with in developing a design for support of the structure. Over 90 rock-socketed drilled shafts ranging in size from 3 to 7 foot in diameter were ultimately used to accommodate the limited space and large column loads, and to adapt to the variable rock surface at the site. Site access during design was limited due to the existing active bus station, so contract documents were adapted to include further explorations. Differences in anticipated and actual field conditions regarding the depth, quality, and variability of the rock had to be overcome in construction. Osterberg Load Cell testing during construction allowed for verification and optimization of the shaft design. Additional issues dealt with on this constrained site in an urban setting included construction staging issues, such as working around specialty contractors for tieback walls, blasting operations for rock excavation, productions issues for hard bedrock, as well as coordination issues with third parties, most notably the Washington Metro Area Transit Authority. Aspects of the foundation design and optimization, preparation of the contract documents to deal with the complicated nature of the project, and lessons learned from construction are also discussed.

Jan 1, 2011

By Emad W. Shublaq

Contractual site plans are implemented for executing pile foundations (5 x 5) at segmental concrete bridge. Project schedule demands have forced the contractor to find out the most economical procedure in achieving the goal. This paper presents a site management technique which is applied by the Contractor. This was found to be fruitful and as much as 60% saving was gained.

Jan 1, 1992

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018

By Wolfgang G. Brunner

The closing of the gap in the European waterway- net is one of the big and challenging traffic projects following the German reunification. The water canals in the North German plain connect the Rhine river, the border between Germany and France, with the Oder, the German border river to Poland. As early as in the 30's of the 19th century the planning and construction of a ship- lift and a canal bridge started, in order to close this last big gap in the system between the Mittelland Canal and the Elbe- Havel Canal near Magdeburg. This main waterway connects the West of Germany, known for its coal mines and steel mills, with the capital Berlin, and from there it goes on into Poland. The building activities started in 1934 but came to a complete stop in 1942 because of the war. The communist government in East Germany was not interested in continuing this huge project, including the ship lock Rothensee, the canal bridge crossing the river Elbe, the former border river between West and East Germany, and the lock Hohenwarthe due to lack of political backing along with low construction capacity.

Jan 1, 2000

By Dawn C. Tattle

[ ] Panoramic View of Completed Facade Supports The following case history describes the installation of earth retention systems, historical facade supports and structural caissons by Anchor Shoring & Caissons Ltd. at the Air Canada Centre/Raptors Stadium Project in Toronto, Ontario, Canada. The Air Canada Centre/Raptors Stadium project includes a 140,000 square foot office tower, a 20,000 seat basketball arena and their support facilities. The arena within the complex will also have the ability to host hockey, ice shows, concerts and family events.

Jan 1, 1997

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"ABSTRACTTheoretical approach to estimate the ultimate pile capacity gives a rough idea at the initial stage of design that later on strengthen by the execution of static pile load test at site. The static pile load test is the only best option for the estimation of ultimate capacity of various types of piles. There are various methods based on strength, serviceability, net deflection for end bearing, shaft adhesion, graphical and extrapolation approaches for the interpretation of pile load test data to calculate the ultimate capacity. In this paper an attempt is made to evaluate the best-fit method for the estimation of ultimate capacity of single helix screw pile. The pile load tests on model scale were performed on screw piles of different helix diameter. The purpose of adopting model scale of testing was to achieve a state at which settlement increases without further increase in vertical load. The ground was compacted with dry sand at denser state. It was observed from the test results that extrapolation methods such as Chin- Kondner and Decourt predict the load settlement curve of screw piles very well, however ultimate pile capacity was on higher side which may not be suitable for the strength of helix plate. Decourt approach to plot the pile load data showed clear indication of the deformation of helix due to strong subsurface condition. A modified approach in Decourt method is proposed for estimating the ultimate capacity of screw pile having deformed helix whereas reduction factor is suggested for Chin-Kondner method for the estimation of ultimate capacity of intact screw pile.INTRODUCTIONDeep foundations are used to avoid the soft ground at shallow depth that is not suitable for carrying the structural load. Different types of piles have been used to transfer the load to deeper stratum. The screw pile is one of the new piling method and its use is considerably increasing. It consists of a cylindrical steel shaft with one or more helices at various length of the shaft. The diameter of helices (Dw) is usually 2 – 2.5 times the shaft diameter (Ds). The pile is installed to the required depth through torque and pressure. The advantage of screw pile over other piling system is its quick installation mechanism, high end-bearing and uplift resistance, noise reduction and minimum use of man power."

Jan 1, 2014

By Leonello Sciacca

Deepening of harbours has become a priority, necessary to the ongoing operation of the wharves in the face of deeper draft merchant vessels and cruise ships. It is now standard practice in many areas to provide for harbours to be dredged to significant depths below mean sea level, in the order of 12.00 m (39 ft) for existing berths and 15.00 m (49 ft) for new wharf construction. The Ravenna Port Authority initiated a project to deepen the harbour bottom at selected wharves to a depth of 12.00 m (39 ft). In preference to reconstruction of the wharves with longer and heavier sheet piling or other equally disruptive reconstruction, they identified the structural reinforcement of the existing wharves by means of deep underwater tie rods as a possible alternative cost-effective solution. Having defined the design concept, effort was concentrated on developing the required technology. A technique, already in use for the installation of tie rods by means of robotics, was identified as potentially suitable for underwater use. It was decided to carry out the fine tuning and the evolution of the technology for a marine environment of the robot unit and of the related remote control software that controls the installation of the tie rods. An experimental test site was set up to refine the drilling, installation, grouting, monitoring and testing of underwater tie rods. The purpose was to confirm the feasibility of the proposed solution and the reliability of these tie rods for use in the reinforcement and construction of wharves. The paper also discusses the theoretical and experimental study of underwater tie rods dealing with the theoretical analysis of the interaction between tie rod and soil, aimed at identifying the correlation between the forces of applied traction and the corresponding measured elongations. A series of tests were carried out with positive results, both at the operating load of 300 kN (67 kips) and at the nominal maximum load of 630 kN (142 kips). The tests were carried out on seven tie rods, of which three were installed at a depth of 5.00 m (16 ft), principally to test the reliability of the operating and remote control systems in the presence of a significant hydrostatic pressure, and four were placed at a depth of 8.00 m (26 ft) to check the load bearing capability of the tie rods positioned at the depth called for by the current project.

Jan 1, 2011

By David Siu

Many problems were encountered with the mechanical wedge-type splices used for the 15-inch square precast prestressed concrete piles installed at an industrial plant site. Many of the wedges were breaking during installation of the splices and after pile driving resumed following splicing. Dynamic monitoring of the piles and uplift loading tests confirmed that the problems were associated with cracked or damaged wedges. More ductile, annealed wedges were subsequently used, and, while not completely satisfactory, they were found to perform better than the original more brittle wedges. Introduction Long precast prestressed concrete piles were installed to support heavy, settlement-sensitive structures at an industrial plant in Port Alberni, British Columbia, Canada. The piles were driven through soft compressible silts and clays to toe bearing in a dense sand and gravel deposit or on bedrock. Each pile consisted of two or three segments joined with mechanical wedge-type splices trademarked DYN-A-SPLICE. Shortly after construction began, problems arose during pile installation, and these problems were, later, identified to be related to the wedges, or clamps, used to connect the splice plates.

Jan 1, 1991

By Jim Frazier

Tradition has often dictated low design load stresses on piles. Such traditions often developed prior to modern static or dynamic pile testing methods and perhaps result from a few limiting situations. These low stress limits were then broadly applied, even in cases where the piles could carry substantially higher loads. With sufficient testing to prove the design, higher design loads may present significant overall savings to the project owner. The cost of the testing then becomes an insignificant cost compared to the potentially great benefit of increased pile loadings. To confirm higher load possibilities for driven piles, the pile is tested either statically or dynamically. Further savings and increased testing efficiency result from remote dynamic pile testing. This paper presents a project where design stresses were considerably increased as a result of additional testing and use of remote dynamic pile testing equipment.

Jan 1, 2002

By Aaron S. Bradshaw, Ryan M. Coulson

The offshore wind industry in the United States is slowly emerging with the recent construction of the first offshore wind farm located off the coast of Rhode Island. The turbines at the Block Island wind farm are supported by piled jacket structures, which historically have been used for much heavier oil and gas platforms. Offshore wind turbines have unique design requirements and the axial behavior of the supporting piles under cyclic loading is important to design. Cyclic degradation along the pile shaft can affect the capacity, deformation, and stiffness performance of the foundation and of the structure as a whole. This paper proposes a strain-based approach to estimate the fatigue (or endurance) limit of a cyclically loaded pile that may be applicable to long-term service loading. The method is applied to an existing load test dataset and the analysis results appear consistent with the observed pile response. INTRODUCTION The demand for renewable energy has been increasing in recent decades and wind power has seen a dramatic increase in popularity. In Europe, as of 2017 there were 4,149 grid-connected offshore wind turbines across 11 countries (windeurope.org), many of which are supported on monopile foundations. It wasn’t until recently (2016) that the first offshore wind farm was constructed in the United States off the coast of Block Island, Rhode Island. The project included 5 piled jacket structures founded in terminal moraine deposits. Future offshore wind development along the U.S. eastern seaboard could possibly utilize jacket structures in granular foundation soils. Loads from wave, wind, and turbine rotation induce cyclic loads on the foundation that have on the order of 108 loading cycles over the service life on the structure (Schneider and Senders 2010). Turbines located along the U.S. east coast have the added risk of hurricanes. As shown in Figure 1a, the lateral loads on a jacket structure are transferred primarily as axial compressive and possibly tensile loads on the supporting piles depending on the weight of the structure. The friction along the shaft of the pile can be prone to cyclic degradation, leading to reduced pile capacity and stiffness, and increased deformations. An offshore wind turbine foundation must be designed for a variety of limit states including ultimate, serviceability, and fatigue limit states. For a jacket structure this would include an analysis of the ultimate axial pile capacity, axial stiffness, and axial deformations, all of which can be affected by cyclic loading both under extreme (i.e. storm) conditions as well as long-term service conditions. Axial pile stiffness is needed, for example, to estimate the natural frequencies of the structure as a whole and to assess dynamic and fatigue loads. The structure must be designed such that its natural frequency remains outside the loading frequencies of the waves and turbine blade passing frequencies to avoid resonance. Therefore, prediction of the axial response of the piles is important to the design of these structures.

Jan 1, 2018

By D. E. Sherwood

Recent developments in high torque hydraulic rotary rigs has lead to the construction of secant bored pile walls by rotary drilling methods in circumstances where earlier methods were difficult and in some cases impossible. The evolution of secant bored pile wall construction is described including classical, rotary drilled and continuous flight auger construction methods. The paper then details the restraints which have been created in recent inner city redevelopment, many of which were not relevant in the early days of the technique. Typical examples of walls are presented to show the adapatability and advantages of the secant bored pile wall method. A number of in-situ retaining wall construction techniques are then compared in detail with regard to relative cost, technical quality and practicality.

Jan 1, 1989

By Romano J. Micciche

One of the largest scale uses of a multiple, high-strength steel bar tiedown system is described. Tiedowns were installed to resist hydrostatic uplift forces acting on a section of the Interstate Highway Route I-90 southern approach roadway to the Third Harbor Tunnel, in Boston, Massachusetts. Site specific information is discussed regarding design, testing, and installation of Tiedowns. Conclusions are presented regarding the overall performance of this system and the application of this type of tiedown system on future projects.

Jan 1, 1994

By Douglas W. Christie

Deep foundations in Washington, DC have played a role in the city?s development since the 19th century. Designers of government and commercial buildings sought deep foundations initially to minimize settlement of structures. As the western portion of the National Mall was made by filling in portions of the Potomac River, numerous memorials and monuments on the Mall required deep foundations. In recent years deep foundations have been used to allow underground construction for various reasons. Commercial developers have sought to maximize the use of sites by developing below-grade space for parking to meet code requirements and offset the limits on building heights. Underground museum and gallery space has been constructed to expand public space while preserving open space above grade. Access and security concerns have prompted the design of underground visitor centers rather than above-grade structures.

Jan 1, 2006

By Hiren J. Shah

The urban environment and geology create unique challenges for design and construction of deep foundations. The effect of these is prominently experienced in New York City. Three such project case histories are presented in this paper. The first project is a multi-use development. Relatively unusual glacial geology was observed at the site during the subsurface investigation phase. This played an important role in the selection of deep foundations as well as during construction. The design and construction aspects of the pile foundations, settlement estimates, a pile drive test program during design, piling equipment and production pile installation are discussed herein. A relatively smaller project is the second case history. A combination of drilled and driven deep foundations was employed in one area of the project due to its unique conditions. In another area of the project, an addition to a structure required the use of supplemental foundations to resist new additional loading. Tight space and load sharing with the existing foundations were important considerations in the design and construction. Finite element modeling of the existing and completed structure was performed which was an interesting aspect of the project. The third project case history involves a very large multi-billion dollar project in which various different types of deep foundation elements were used. The aspects requiring the use of such a variety of types and sizes of deep foundation elements included: geologic conditions, re-use of existing foundations, protection of adjacent infrastructure, construction staging, restricted space, loads, deep excavations, cost and schedule.

Jan 1, 2011

By Jason N. Scott

CFA piling is a ?blind? construction process that relies heavily on the rig instrumentation to produce sound piles. If the data measured and recorded during construction can be made available to engineers and managers within hours after construction then there are many economic and quality control benefits that can be realised. A state of the art CFA instrumentation and data management process has been developed in the UK. The key components of the instrumentation, GSM data service and the central database are described. Many benefits to the business have been realised and, where possible, these are quantified.

Jan 1, 2006

By Patrick E. Durnal

A joint venture of Ben C. Gerwick Inc., Sverdrup (now Jacobs) and DMJM (now DMJM Harris) designed the $779 mill seismic upgrade of the Richmond - San Rafael Bridge over the San Pablo Bay in the San Francisco Bay Area and provided construction support to Caltrans. Construction of the marine foundation retrofit was completed by a joint venture of Tudor Saliba/Tidewater/Koch-Skanska and their subcontractors: Pomeroy Precast Construction, AGRA Foundations, Dutra Construction and Vortex Divers. Construction management and inspection was performed by Caltrans with support of various consultants.

Jan 1, 2013

By D. Goossens

Quality control is a system which should guarantee that quality is achieved. It is the execution and verification of a project in an organised way, in order to obtain the maximum of certainty that the results meet the requirements. This concerns all stages of the project, from the soil investigation, over the design, to the execution. Quality control can and has been successfully realised for important projects by means of a quality plan. A quality plan is based on a number of general considerations, but should certainly be focussed on the particularities of a specific project. Practical examples of quality plans, which have been realised on sites in Belgium, are developed and the advantage of the system is shown by concrete case studies.

Jan 1, 1996

By Markus Schönit

Double rotary drilling combines continuous flight auger drilling with a casing for producing a cast-in-place pile. When producing a pile an outer casing and an auger (hollow auger) rotating inside the casing are driven into the ground in counter-rotation. The outer casing serves to support the surrounding soil and the inner auger excavates the drilling cuttings to the surface inside the casing. After reaching the projected drilling depth concrete is pumped through the hollow stem of the auger and outer casing and auger are extracted. After their complete extraction a reinforcement cage can be inserted in the fresh concrete. Compared to Kelly drilling the double rotary drilling method offers numerous advantages, including, for comparable diameter and length, shorter production times and higher accuracy (pile inclination and excess concrete) combined with increased occupational safety and lower noise emissions. Moreover, pile tests have proved that piles produced by double rotary drilling feature higher axial load-bearing capacities than comparable piles produced by Kelly drilling. This article offers an overview of the basic theoretical principles of double rotary drilling lists the required and currently available machinery and, finally, discusses the results and conclusions of a current jobsite.

Jan 1, 2011

By Bengt H. Fellenius

THIS PAPER deals with the analysis of results from axial testing of vertical single piles, i.e. the most common field test per-formed. Despite the numerous tests which have been carried out and the many Papers which have reported on such tests and the analysis thereof, the understanding of pile test loading in current engineering practice leaves much to be de-sired. The reason for this is that the engineers have concerned themselves with mainly only one question: "Does the pile have a certain least capacity?", finding little of practical value in analysing the actual capacity and the pile-soil interaction. This Paper aims to show that engineering value can be gained from elaborating on a pile test ? during the actual testing in the Held, as well as in the analysis of the results. The first portion of the notes make use of an earlier Paper by the author (Fellenius. 1975). However, additional views and recent literature have been incorporated.

Jan 1, 1988