Search Documents

By Janaka J. Kumara, Takashi Kurashina, Yoshiaki Kikuchi, Takahiro Yajima

"The inner frictional resistance of open-ended piles depend heavily on the degree of soil plugging. Many factors including pile diameter, relative density and end conditions of the piles influence the degree of soil plugging. In this paper, the effects of inner sleeves attached at the pile base on the inner frictional resistance are discussed. The experiments were conducted on a medium-dense sandy ground using smallscale model piles. The results suggest that the inner frictional resistance is influenced by sleeve height for 50 mm diameter piles although it is independent for 30 mm diameter piles. The results also indicate that soil plug height is influenced by the sleeve height. The results of the incremental filling ratio (IFR) showed that penetration of non-sleeved piles is closer to unplugged state than the sleeved piles. The results of the IFR also reveal that the degree of soil plugging is affected by the sleeve height for 50 mm diameter piles although the variation is very limited in 30 mm diameter piles. The results on the coefficient of lateral earth pressure suggested that it increases from 1.08 – 1.75 when the sleeve height is increased from 10 – 100 mm for 50 mm diameter piles.INTRODUCTIONPrevious studies have shown that the behaviour of open-ended piles is different from closed-ended piles (Szechy, 1961; Randolph et al., 1979; Paikowsky and Whitman, 1990). Open-ended driven piles are widely used for deep foundations, in particular in offshore deep foundations. Generally, it is accepted that a short open-ended pile produces a smaller bearing capacity than a similar closed-ended pile (Nauroy and Tirant, 1983). However, a long open-ended pile can produce a similar bearing capacity as a closed-ended pile due to a large inner frictional resistance mobilised between the inner pile shaft and inner soil (Lehane and Randolph, 2002). The ultimate bearing capacity of an open-ended pile, Qu consists of three components as given in Eq. 1."

Jan 1, 2017

By Meeok Kim, Paul Beljan, Gordon Chen

"Clinton combined sewer overflow storage (CSO) facility project developed by the Department of Water Environment Protection of Onondaga County, New York, is to improve sewer facilities and infrastructure in Syracuse, New York. The below grade facility will provide a storage of untreated stormwater during highflow periods to be treated later, thus reducing CSO discharges to Onondaga Creek.The CSO system consists of three parallel storage tunnels and two end chambers (west and east chambers) as main underground structure. The storage tunnels are about 850 ft. long, 55 ft. wide, 24 ft tall and located 20 ft deep below grade. The chambers, include above access and operation structure, are about 40 to 55 ft. deep and approximately 60 to 100 ft. wide.Kiewit Infrastructure and Weidlinger Associates Inc. developed an alternative approach for the tunnels to meet the facility completion schedule, strict design guide lines and quality control as an environmental and water tight concrete structure for the project. The original design anticipated use of a TBM machine to bore three parallel tunnels between two previously constructed chambers.The alternative design used a three barrel culvert cast-in-place structure in a cut and cover excavation supported by a soil bentonite wall. The SOE along the jet grouted bottom seal provided a ground water cut off as well.The SOE system is specially designed to enhance the quality of culvert CIP structure construction by providing enough space for a full height construction. Also it further reduces the construction time by having the less squarefootage of jet grout installation. The design of tunnel systems is accomplished effectively through the utilization of soil structure interaction using a finite element methodIntroductionTo avoid construction of an additional treatment plant to handle increases in combined sewage flows, the Department of Water Environment Protection of Onondaga opted to construct the Clinton combined sewer overflow storage (CSO) facility.The Clinton CSO facility provides an environmental friendly mitigation method for combined sewer overflows on Onondaga lake which is located in northwest of Syracuse."

Jan 1, 2015

By Timothy C. Siegel

In response to a solicitation for ground improvement for the construction of a new hospital in Owensboro, Kentucky, the team of Berkel & Company Contractors and Dan Brown and Associates PC designed and installed lightly reinforced cast-in-place piles (known commercially as Cast-in place Ground improvement Elements or CGEs) as part of a composite ground system. The concept of the design is that the structure load is shared between the piles and the soil subgrade. The load sharing is controlled (to some degree) by the placement of a cushion between the pile head and the bottom of the overlying spread foundation. In an effort to confirm the design principles and to better understand the behavior of composite ground, the design-build team performed plate load tests on ground with a single CGE and with a group of CGEs. The small plate test (on ground with a single CGE) characterized the stiffness of the cushion. The large plate tests showed that the cushion will distribute the applied load to the CGEs and to the soil subgrade between the CGEs. On the basis of the plate tests, it was concluded that the plate stiffness can influence the test results. The use of a concrete layer was effective at supplementing the plate stiffness. The cushion was shown to be an important component of a composite ground system by allowing mobilization of the soil subgrade resistance and avoiding a stress concentration at the tops of the CGEs that would otherwise be present if the spread foundation and piles were rigidly connected. Because the composite ground system engages the resistance of the soil subgrade, the structural demand is reduced and consequently there is a potential for savings when compared to a conventional pile foundation. Several foundations for the new Owensboro hospital are being monitored for vertical movement during construction of the superstructure that will extend through 2011. At the time of this paper (mid 2011) the settlement of the foundations due to only part of the structural load (primarily the structural steel) has been negligible.

Jan 1, 2011

By Julie Hampden, Tim Dardis, Per Reinhall

"Noise from impact pile driving can harm fish, marine mammals and other sensitive wildlife over large areas. Marine pile driving is highly regulated, and regulators require sound levels to be below certain thresholds to avoid harassment and injury to sensitive marine life. In many locations, timing restrictions, use of noise attenuation technologies and extensive monitoring for impacts to wildlife are also required. As a result, permitting can be laborious and time consuming, and project implementation and scheduling can be complicated. Underwater noise levels are measured with an underwater microphone (hydrophone), which converts noise pressure to voltage and is calibrated to express the noise pressure in Pascals (Pa). The pressure is often expressed using a logarithmic scale, in decibels (dB). Several specific metrics can be used to describe underwater noise. Three common metrics are the instantaneous peak sound pressure level (dBpeak), the root mean square pressure level (dBRMS) and the sound exposure level (dBSEL) referred to as the peak, RMS and SEL levels, respectively.During impact pile driving, the peak pressure represents the instantaneous maximum pressure, either overpressure or underpressure, observed during each pile strike. The RMS level is the square root of the mean of the square of the pressure during the duration of the impulse; it is the average pressure level of the pile strike from beginning to end. The cumulative SEL (SELcum) is calculated by summing the cumulative pressure squared and integrating over time of duration of the pile strike. SEL is used as an indication of the cumulative energy of a pile driving event, which may consist of one or many pile strikes.Regulatory agencies use these metrics to help characterize the noise pressure levels that can affect sensitive species. Some of the most frequently encountered biological thresholds in the Northwestern United States that are used by regulators to describe potential impacts to sensitive species are summarized in the following table. Agencies have defined thresholds for different types of injury, either hearing or bodily harm, and for temporary injury or disturbance."

Jan 1, 2017

By Wolfgang G. Brunner

Mai- Liao, in Yun Lin province of Taiwan, which was once a remote area on the coast of the South China Sea, has been developed into an offshore industrial complex. Approximately 100 million m3 of imported sand fill were used to reclaim the site from the sea with an overall area of almost 3.000 hectares. Land reclamation started in March 1994 and was completed at the end of 1998. A total of 41 industrial plants were constructed on the site, including an oil refinery, a naphta cracking plant, a cogeneration plant, a coal- fired power station, a heavy machinery plant, a boiler making plant, water purification plant, several petrochemical plants and a new harbour. From 1998 onwards, new plants were taken into operation in uninterrupted succession. The main purpose of the ground improvement by vibro- displacement, used predominantly to form the foundations of the oil storage tanks , was to reduce the liquefaction potential of the subsoil during earthquakes. The top layer across the site was treated by dynamic compaction before the installation of the stone columns. Heavy structures such as chimney- stacks and buildings were constructed on pre- cast concrete piles driven by diesel hammer. The earthquake design criteria specified an earthquake magnitude M = 7.3 and an acceleration a = 0.21 g. Stone columns were installed by the dry bottom feed process, which was controlled by an automatic monitoring system, to depths ranging from 13 to 20 m to provide flexible tank foundations. Installation of 1.500.000 linear m of stone columns commenced at the beginning of 1997 and was completed in August 2000. 60 % of the stone columns, in particular the deep ones, have been carried out by Bauer vibrators. The Chi- Chi earthquake ( M = 7.3 ) took place on 21 September 1999 and was followed by Cha- I earthquake ( M = 6.8 ) on 22 October 1999. A survey carried out after these earthquakes showed very positive results. The maximum observed settlement was 10 mm and none of the tanks suffered any damage.

Jan 1, 2002

By Kamil Nuzha, Jianchao Li, Bashar S. Qubain

"The Philadelphia Water Department is rehabilitating Belmont Raw Water Basin. As part of this work, a 500-ft long, temporary cofferdam was designed to retain 35 ft of combined water and soil at the western half during the reconstruction of the eastern half. A cofferdam that comprises two integral rows of sheet piles was selected to take advantage of the soil’s weight between the sheet piles for increased stability. To fine tune the design, a geotechnical investigation was carried out to verify the subsurface conditions and, in particular, the top of rock variations along the centerline of the cofferdam. A detailed finite element analysis was performed based on the subsurface findings and incorporating the construction sequence to evaluate the behavior of the cofferdam at the following stages: installation of tie rods to connect to the two rows of sheet piles; partial excavation and installation of tiebacks; complete excavation of the east basin, and demolition of the cofferdam. Inclinometers and survey markers were installed every 100 ft along the cofferdam and were monitored throughout construction. The deformation measurements were in good agreement with the finite element results.INTRODUCTIONThe Philadelphia Water Department (PWD) Belmont Raw Water Basin is located at the intersection of City Line and Belmont Avenues in Philadelphia, PA. The facility actually contains two raw water basins, east and west, separated by an earthen dividing dike. Water leakage at the bottom of the basins and through the dividing dike together with increasing demand for a larger storage capacity dictated the replacement of the wide earthen dike with new narrower concrete structure. The temporary cofferdam was designed for a two-year period to facilitate excavation support, water cutoff, removal of the existing earthen dike and replacing it with a new concrete dike. During this construction sequence, the water level in the west basin had to be maintained at or near its full capacity.Various excavation support systems were considered for this project prior to the selection of a double wall sheet pile cofferdam. Fig. 1 shows a plan view of the cofferdam and the new dividing dike. A typical cross section of the two structures is shown in Fig. 2. Double row sheet pile walls are commonly used as both temporary and permanent retaining systems in open water applications such as construction works, quaywalls, breakwaters and revetments for storing industrial waste as indicated by Ohori, et al. (1984), Ohori et al. (1988), and Khan, et al. (2001). There are many advantages to double row sheet pile systems as recognized by Ohori, et al. (1984; 1988): (1) It can be installed and removed in the presence of water easily and quickly; (2) it provides stability with small width to height ratio, utilizing the existing soils between the installed sheet pile rows; and (3) it serves well as a means for water cutoff. These advantages meet the specific project requirements."

Jan 1, 2016

By Beim Jorge, Piscsalko George

"Verifying the quality of cast-in-place foundation applications, particularly those cast under slurry, is of course important, due to its great dependency on the methodology employed and on the practices of the site personnel. Due to the techniques used to install these elements, it is usually not possible to inspect the hole prior to grout or concrete placement, but there are several Non Destructive Test (NDT) methods available to assess the integrity of the completed foundation elements. This paper will compare several NDT methods with the Thermal Integrity Profiling (TIP) method for verifying the integrity in Continuous Flight Auger (CFA) piles and Bored Piles. The Thermal Integrity Profiling method will be described and some examples will be presented where TIP testing was used to confirm the structural integrity of CFA piles and Bored Piles.IntroductionThere are several Non Destructive Test (NDT) methods available for integrity testing of foundation elements. Each of those methods has advantages and disadvantages (White et al, 2008). Some methods test the integrity based on the reflections of a stress-wave generated by low or high-strain impact, while others require tubes to be installed prior to concrete pouring, and test the integrity between those tubes, or within a small proximity of them. The former methods (especially the low-strain) are faster and more cost-effective, but are not able to detect the quadrant where the damage is located. The latter methods are able to determine the quadrant, but do not test the region outside of the reinforcing cage, that is, they are not able to determine the concrete cover. The Thermal Integrity Profiling (TIP) NDT method overcomes the limitations of these other NDT methods.Overview of Shaft Integrity MethodsUntil now, the most widely used methods to test the integrity of Bored and CFA piles were the low-strain pile integrity testing and the cross-hole ultra-sonic testing. The low-strain method for integrity testing (PIT) involves attaching an accelerometer usually to the pile top (using a putty or wax) and striking the pile surface with a handheld hammer, which causes a compressive wave to enter the pile. This wave is totally reflected when it reaches the end of the pile or a major defect, and is partially reflected when it encounters any change in crosssection, or a change in the resistance or density of the pile material. These reflections arrive at the top at a time determined by the distance and wave speed, and causes a noticeable change in the signal detected by the accelerometer. The acceleration signal is normally converted to velocity by simple integration, and sometimes the force applied by the hammer is also measured. The velocity (and force) signals can be processed by the pulse-echo method (in the time domain) or by the transient response method (in the frequency domain)."

Jan 1, 2015

By I. Stanculescu

The consolidation of thick and very compressible soil deposits by stone columns associated with cast-in-place plain concrete columns, has been performed for shallow foundations of some heavy industrial structures. The reduction of settlements and increase of soil bearing capacity were thus ensured as a result of soft soil interaction with stone and concrete columns. The results of model tests and in situ large scale applications are presented. A calculation procedure is also suggested for foundation bases improved by the proposed method.

Jan 1, 2010

By Hannah Lezzoni, Morgan NeSmith

The Augered Cast-in-Place and Drilled Displacement Pile Committee has historically been one of the most active and engaged DFI committees and has performed or spearheaded a number of research projects via the DFI Committee Project Fund (CPF). The authors have had the privilege of being either past or current committee chairs and have been involved in the performance of most of these projects since the fund's inception. The following is a historical overview of the committee's projects and their outcomes.

Nov 1, 2023

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

Large diameter open-end pipe piles are increasingly used as deep foundations to support heavy onshore and offshore structures. During the driving process, several factors such as subsurface conditions, hammer type, hammer efficiency, pile type, plug conditions, temporarily increased base resistance, and loss of shaft resistance have direct impact on the driveability of large diameter open-end pipe piles. In a uniform subsurface condition, the unit shaft resistance increases with depth. Consequently, more resistance is accumulated as piles penetrate to greater depths which results in higher driving resistance. However, according to the friction fatigue analysis, the greater the number of shearing cycles occurring on a soil segment along the pile shaft, the greater the reduction of its shear resistance. As a consequence, since upper soil layers are subjected to a greater number of blows than those at greater depths, they have a relatively lower resistance compared to what would be calculated with standard geotechnical analysis methods. As a result of this progressive and nonuniform loss of shaft resistance with driving, blowcounts tend to increase at a lower rate than expected from traditional analyses. This paper discusses one of the approaches to the driveability analysis with the geotechnical friction fatigue consideration. It also shows comparisons between predicted driveability obtained from wave equation analysis and field driving records. All analyses were performed for a 2.134 m (7.0 ft) diameter open-end pipe pile installed at a total depth of 192.90 m (554 ft). Two separate static resistance and wave equation analyses were completed for the case study presented in this paper: 1) Friction Fatigue analysis based on the recommendations of Alm and Hamre (2001), subsequently referred to as the FF model, and 2) Standard Driveability analysis based on soil set- up factors, hereafter referred to as the SD model in this paper. Results from analyses included the shaft resistance distributions compared to the result of the signal matching analyses determined from the pile dynamic measurement. Furthermore, predicted blowcounts were compared to observed blowcounts during the pile driving. The comparison analyses indicated a 54.4 percent resistance loss of the Static Resistance during Driving (SRD) due to the geotechnical friction fatigue corresponding to a 46 percent reduction in total resistance. The analyses also showed that average predicted blowcounts using the friction fatigue were 6.4 percent lower than measured blowcounts, whereas, the standard driveability approach showed 42.1 percent higher blowcounts compared to the blowcounts shown in the driving log values.

Jan 1, 2019

By Randy R. Williams, Brian W. Wilson, George M. Filz, Marina S. W. Li

"Detailed design of an extensive deep mixing (DM) scheme using the Cutter Soil Mixing (CSM) technique was completed for foundation support of mechanically stabilized earth (MSE) walls for Kitimat Liquefied Natural Gas (LNG) at Bish Cove, British Columbia, Canada. The design was based on the provision of soil-cement structures, constructed in highly variable subsurface conditions that consisted of thick deposits of fine-grained soils overlying granular soils, and required to meet project-specific performance criteria, to support the MSE walls. The design, consisting of rectangular CSM panels constructed to form barrettes connecting to a longitudinal wall of continuous CSM panels, was configured to manage the distribution of stresses and strains that could be developed within the soil-cement structure.The results from 2D finite element analyses were used to determine the necessary arrangement and properties of the CSM panels to accommodate localized areas of relatively high shear, tensile and compressive stresses within the soil-cement structure. The relationships between unconfined compressive strength and elastic modulus for fine-grained and granular soil-cement structures obtained from the Bish Cove data were compared with published references and were found to be significantly different in the higher strength range materials.BACKGROUNDDeep Mixing design was completed for the development of the Kitimat LNG Facility located in Bish Cove, British Columbia, for support of two relatively high MSE walls and associated bulk earthwork operations. Deep mixing was necessary to treat the very weak native deposits in-situ to meet project performance requirements and physical constraints without the need for significant excavation and disposal work. The DM design was undertaken on the basis of adoption of the CSM technique for in-situ ground improvement of the native foundation soils which consisted of very soft to soft fine-grained marine deposits and loose to compact sandy silt to silty sand, overlying dense sand and gravel (Fig. 1). The DM area is located immediately upslope of the Bish Cove beach area, and is “L” shaped in plan, approximately 300 m long by approximately 28.8 m wide (parallel to the beach area) and 165 m long by an average width of 21.0 m (perpendicular to the beach area). The depth of the DM ranged from about 5.0 m to 30.7 m with typically 2.0 m embedment into dense granular soils. Details of the design philosophy, including an overview of the DM design and the project background information are presented by Li et al. (2014a). Details of the construction aspects of the Kitimat LNG deep mixing are presented by Wilson et al. (2014)."

Jan 1, 2015

By Mark S. Greenleaf, Alec D. Smith, Mary Vittoria-Bertrand, Heather B. Scranton, Jean Louis Z. Locsin

"Rhode Island’s new $163.7 million, 2,265 ft (690 m) long, four-lane Sakonnet River Bridge sits just south of the existing bridge in Portsmouth/Tiverton. The bridge, a critical transportation system link between Massachusetts and Rhode Island, has a steel I-girder main span and concrete New England Bulb Tee approach spans. The foundation work was done between October 2009 and July 2010, and the bridge was completed in February 2014.Foundation design and construction challenges make the project noteworthy. There were thick layers of silty glacial soils with bedrock as deep as 400 ft (122 m) below the waterline, coupled with high foundation capacity demands at the river piers in 50 ft (15 m) of water. The Sakonnet was one of the first major bridge projects in the country to incorporate AASHTO Load and Resistance Factor Design (LRFD) guidelines for foundation design and construction. Because of these and other challenges, the engineers conducted two design-phase load test programs on several foundation elements. These programs were successful and allowed the engineers to adjust the final foundation design prior to the start of construction. During construction, the contractors drove thirty 6 ft (1.8 m) diameter steel pipe piles, each with a novel recessed steel plate insert, to depths of 130 to 200 ft (40 to 61 m) at the three river piers. The insert provided increased resistance of the steel pipe piles and saved about $9 million. Also, 457 14x117 en bearing or friction H-section piles were driven to between 50 and 190 ft (15 to 58 m) at five land piers. All piles were driven relatively close to the existing bridge, which remained in service during construction, due to the project team’s precautionary use of instrumentation and the installation of a jacking system.Area GeologyThe Sakonnet River is up to 60 ft (18 m) deep along the bridge alignment and is underlain by a deep bedrock valley. The bedrock valley is buried by at least 350 ft (107 m) of soil, which includes a complex sequence of interbedded glacial soils (glacial till, glaciolacustrine deposits and glaciofluvial deposits), overlain by geologically recent estuarine deposits. The soils having the greatest impact on the foundation resistance are the glaciolacustrine (fine sandy silt or silt) and glaciofluvial (silty sand with gravel, cobbles, and occasional boulders less than about 2.5 ft [0.8 m] in size). The soil overburden decreases toward the east and west banks of the river, as the bedrock surface rises."

Jan 1, 2015

By I. K. Ozaydin

Analysis of piles groups loaded with large bending moments and both vertical and batter piles can be best performed by matrix analysis. In this paper, a case history about a tall marine control tower is presented. The soil conditions at the site and the results of the computer analysis of the piled foundation are summarized. It is shown that the pile loads are indeed less than the allowable load for a single pile. Pile head loads and moments are used in the analysis of the raft foundation.

Jan 1, 2010

By Lisa M. Splitter

Drilled displacement piles were constructed as the foundation for a proposed 10-story building in San Francisco, California. At the study location, the stratigraphy consists of 14 to 21 feet of fill and 13 to 23 feet of weak, compressible clay (?Bay Mud?), underlain by dense sand, stiff clay, and bedrock. A sensitive critical public utility is located within approximately 20 feet of the constructed piles along one side of the building. The utility pipeline is entirely within the Bay Mud where it is adjacent to the project site. The San Francisco Public Utilities Commission (SFPUC) developed limits on the allowable total and differential movement of the utility pipeline. As requested by the SFPUC, inclinometers and piezometers were installed to monitor the soil movement and pore pressure increases in the Bay Mud caused by the installation of drilled displacement piles. Action levels were set such that if displacement and/or pore pressures reached an action level, the installation methodology would be reevaluated and additional measures to reduce these effects would be implemented. This paper will present the sequence of pile installation near the pipeline and monitoring points, and the data collected from inclinometers and piezometers at variable depths and distances from the piles. The data will highlight the build-up and dissipation of pore pressures over time and the displacement of Bay Mud caused by the pile installation. The conclusions of the study are useful in determining sequencing, spacing, predrilling, and other measures that can be implemented to decrease the displacement potential and pore pressure build-up in soft clays.

Jan 1, 2009

By Brian McGlynn

There are many factors that can result in a site characterization being limited. For example, a client may undervalue the importance of a good geotechnical report, or an owner may feel that it would take too much time to perform an appropriate investigation among other reasons. For this project, neither was the case. The challenge was that the construction sequence of work required wick drains to accelerate the settlement of soil that had yet to be placed, resulting in the need to create a wick drain bid package based on unknown settlement parameters. This wick drain project took place in Long Beach, California, at the Long Beach Middle Harbor Re- development. For much of the past decade, the Port of Long Beach undertook a $1.5 billion redevelopment of two outdated terminals to create the Long Beach Container Terminal (LBCT). To achieve this goal, the existing terminals were demolished and the slip that serviced one of the older terminals was designed to be infilled to create the new area that would allow for the LBCT to manage 3.3 million TEUS (a commonly used freight term meaning twenty-foot equivalent unit) of cargo each year. Ultimately, the construction of the LBCT would be performed under multiple contracts to allow the new terminal to begin operation in a phased approach. Menard performed the wick drain installation under two out of three contracts, and this case history focuses on the challenges anticipated and faced under the second of these awarded contracts.

May 1, 2023

By H. R. Masoumi

This paper presents a numerical model for the prediction of free field vibrations due to vibratory and impact driving. As the focus is on the response in the far field, where deformations are relatively small, a linear elastic constitutive behavior is assumed for the soil. The free field vibrations are calculated by means of a coupled FE-BE model using a subdomain formulation, proposed by Aubry and Clouteau (1992). The model is validated by means of the results of Kaynia and Kausel (1991) for the impedance of a single pile. First, the case of vibratory pile driving is considered, where the contributions of different types of waves are investigated for several penetration depths. The results show that in the near field, the response of the soil is dominated by a vertically polarized shear wave, whereas in the far field, Rayleigh waves dominate the ground vibration and body waves have been importantly attenuated. Second, the case of impact pile driving is considered. A linear wave equation model is used to estimate the impact force during the driving process. Furthermore, it is investigated how the soil stratification influences the ground vibration considering the case of a soft layer on a stiffer half space. The results show that when the penetration depth is smaller than the layer thickness, the layered medium has a small influence. However, when the penetration depth is larger than the layer thickness, these effects become more significant. Finally, the computed ground vibrations are compared with experimental data reported in the literature.

Jan 1, 2006

By David K. Crapps

The drilled shaft load tests at Port Orange were part of a demonstration project sponsored by the Federal Highway Administration (FHWA) and the Florida Department of Transportation (FDOT). Three load tests were conducted. Test 1 was a conventional test with the test shaft loaded from the top. Test 2 included an Osterberg load cell at the tip and a conventional load test from the top. Test 3 used an Osterberg load cell at the tip of a production drilled shaft. All three test shafts were socketed into limerock and were carried to failure. This paper describes the test program and presents a summary of the test results. Figure 1 presents some photographs of the load test setups and Figure 2 shows the location of the drilled shaft load tests. SITE CONDITIONS The Port Orange Bridge is located on US A1A over the Intercoastal Waterway in Port Orange, Florida (south of Daytona Beach). The new bridge will provide four lanes of traffic with a 65 foot vertical clearance for Intercoastal Waterway traffic. The channel and flanking piers will be supported by 54" drilled shafts socketed into the rock. The bridge is being constructed in two phases. The southern half will be completed first, the old bridge removed and then the northern half will be constructed. The first phase is scheduled to be opened to traffic in October 1989. Each of the four piers near the channel will be supported by 12 drilled shafts with 6 shafts per pier being constructed in each phase.

Jan 1, 1989

By Ivan Jackson Madura

The new Paradisus Coco Beach Resort in Rio Grande (PR) is located on an old swamp area, which has been filled with relatively clean to silty sands. The swampy deposits consists of organic silts, peat and loose fine to medium sand and silty sand. The project requires the placement of 1.0 to 1.5 meters of additional fill together with the construction of light structures. The need for the fill will trigger the development of settlements in the underlaying weak and compressible stratum. Furthermore, the susceptibility of the loose sand to liquefaction during an earthquake was considered. This paper describes the soil improvement by means of vibro-replacement, the purpose of which was threefold: reduction in total and differential settlement, acceleration of settlements during the surcharge period and densification of the loose sand to reduce its liquefaction potential. The predesign is presented together with relevant construction details of the preliminary trial areas from which the final column diameter and grid spacing were derived. Instrumentation together with settlement observations during the surcharge period are presented as well and compared with the initial predictions.

Jan 1, 2002

By Marco D. Boscardin

Control and mitigation of building response to construction activities are assuming a greater role in design decisions for underground construction. Alternatives for controlling building response have multiplied with the continued development of ground modification methods, better control of construction activities that cause ground movements, and increased understanding of building behavior and response. This paper describes approaches to estimating building response to construction-related ground displacements caused by adjacent excavation and highlights the discussion with several case history examples. Examples discussed includes experiences with two, seven-story historic structures, supported by timber piles with granite block pile caps, which were underpinned in preparation for ground-freezing ground stabilization and tunnel construction beneath the buildings. The elevation of each building column was monitored and elevation adjustments were actively performed during construction. The second example examines the performance of a slurry wall braced cut, 45 to 50 feet deep penetrating through a stiff crust into a soft clay layer and associated building response. This cut was immediately adjacent to two, approximately 15-story office buildings, which were supported by deep foundations founded in the stiff crust.

Jan 1, 2003

By Fritz J. Klingler

From site demolition, to design, to construction, Detroit's new Tiger Stadium project is required to be completed within a short 2 ½ years from award of the design-build contract. Such extreme schedule requirements together with somewhat difficult ground conditions at the site, resulted in several challenges in the design and construction of the deep foundation system for the stadium. During the geotechnical investigation, an intermittent water bearing sand layer was encountered overlying the hardpan at the site. As a result, some concern developed regarding the potential for collapse of caisson bells within this layer, as well as the potential for flooding of the caissons during drilling. Although sand and/or ground water was encountered within about half of the caissons, standard drilling and belling methods were used, and adverse conditions were controlled in almost all cases through expeditious drilling, inspection and concreting of the caissons. This paper will present a summary of the ground conditions, design and specification requirements, and construction methods used to successfully install the caissons for this project.

Jan 1, 1999