Search Documents

By Rasin Duzceer

In this paper, the results of pile load test on 24 piles from twelve sites are presented. The pile load tests were performed on 14 driven and 10 bored piles of varying diameters and lengths installed in different ground conditions in Turkey, Saudi Arabia and Kazakhstan. The purpose of this study is to evaluate and compare the axial capacity of the piles obtained using pile load test interpretation methods. Davisson, Brinch Hansen %80, Chin-Kondner, Shen-Niu, De-Beer, Housel, Mazurkiewicz, Fuller-Hoy, Brinch- Hansen (90%), Corps of Engineers, Butler Hoy and Tangent Intersection methods were used to determine the axial capacity of the piles. Static analysis using FHWA method was performed to predict the axial capacity of the piles. A statistical analysis was performed to compare and quantify the load test interpretation methods. The ratio of interpreted (Qi) to predicted (Qp) pile capacity was compared for each method. For each pile load test and for each interpretation method, the mean and coefficient of variation of (Qi)/ (Qp) were calculated. Among twelve methods investigated, the highest Qi/Qp value was obtained as 1.37 for Chin-Kondner method whereas the lowest Qi/Qp ratio of 0.70 was obtained from De Beer method.

Jan 1, 2002

By Robert B. Bittner

The Sutong Bridge across the lower Yangtze River in China will have, when completed, the longest span (1,088 m) and the highest towers (306 m) of any cable stayed span in the world. The foundations for this record setting span will also be record setting. They are located in water depths exceeding 30 m with maximum flows exceeding 3 m/sec. The soil at the site of the main pylons consists of layers of silty sands and silty clays extending to bed rock at 270 m below river elevation. This paper describes the innovative methods used by the team of foundation designers and constructors to support this record setting bridge at this very challenging site. This paper covers three specific topics related to the foundations of the Sutong Bridge: ? Design and construction of the 131 drilled shaft (2.8/2.5 m diameter and 114/117 m long) under each of the two main pylons, including the post-grouting of all drilled shaft tips. ? Design and construction of the scour protection for the two main pylons, ? Construction methods used to construct the waterline pile caps (113.8 m by 48.1 m by 13.3 m deep) under each pylon.

Jan 1, 2013

By Seyyed Mehdi Radeghi Mehrjou

The current work investigates the behavior of inclined micropiles under seismic loads. The dynamic finite element method (FEM) was employed. Rayleigh damping was applied to the soil, and elastic beam elements were employed to model the micropiles. The micropile structure was assumed to have one degree of freedom as a column with concentrated mass. The numerical modeling of micropiles was performed to explore the effects of their inclination on their seismic performance within homogeneous soils with uniform stiffness. In addition, the effect of soil stiffness was studied by considering various stiffness in soil depth. The results from the studies have shown significant effects on the dynamic amplification and internal seismic-induced loads of inclined micropiles.

Sep 1, 2022

There are many ways to classify structural slurry wall elements, but the DFI committee chooses to limit these descriptions to three functional requirements, namely: design function, plan configuration and type of panel reinforcement. (See Figure 1 in Part IV for panel classification). Slurry walls can function as: 1. Curvilinear or linear elements for temporary and/or permanent structures to resist lateral forces transferred from the ground, water, earthquakes and various surcharge loads. 2. Load bearing elements in various plan shapes to resist vertical forces. 3. Combination Elements to resist combined forces under conditions 1 and/or 2. For example, elliptical shafts with various openings for tunnels and conduits have been commonly used for deep excavations.

Jan 1, 2005

By Roger A. Bullivant

As the UK's foremost domestic foundation underpinning contractor over the last 25 years it has become abundantly clear that the size of the repair market, some £500m per annum is a significant waste of resource and cost. To experience this scale of foundation failure in mainly new construction less than 20 years old is unacceptable. This is being further endorsed by our contracting experience in the USA over the last 10 years. Our foundation repair systems are mainly based upon the use of driven mini piles and it was considered appropriate that this type of pile should be upgraded and used on new build construction where the ground was marginal or bad.

Jan 1, 1995

By Cheng Lin

The Group Equivalent Pile (GEP) approach was proposed by researchers to analyze a laterally loaded pile group. This approach enables engineers to evaluate the behavior of a pile group in single pile analysis software, such as LPILE. A previous study showed that the calculated results using the GEP approach for piles agreed well with field test data. To evaluate the accuracy of the GEP method for analyzing laterally loaded shafts, two case studies with different shaft diameters were performed in this study. The comparisons showed that the calculated results using the GEP method and considering the contribution of the shaft cap if embedded generally agreed with the measured from the full-scale tests.

Jan 1, 2009

By Tianfei Liao

Extensive site investigations revealed that abandoned shallow mine workings exist under a site planned for construction of a major new facility. Since the mine voids were susceptible to collapse, they were stabilized by grouting. After completion of the mine remediation, three types of deep foundations (micro-piles, auger-cast piles, and drilled piers) were considered for this site. Micro-piles spread the load via the bond between the pile and the bedrock. Without significant length socketed in rock, the axial load of auger-cast piles and drilled piers has to be concentrated on end bearing. Although spreading the load is preferable in this environment, economic consideration dictated the choice of drilled piers for construction.

Jan 1, 2009

By Charles R. Conlon, Matthew J. Niermann

This paper presents the underpinning and excavation support systems used for construction at 2100 L Street in Washington, DC. The excavation for the proposed building extended below bedrock, which presented significant challenges for underpinning the historic Stevens School, constructed in the late 1800’s. The Stevens School was underpinned using several techniques consisting of soil mixing below an unreinforced foundation, traditional hand-dug pits to rock, micropiles below rock, and bracket piles. The excavation support system for the remainder of the project consisted of soldier piles and lagging supported laterally by tiebacks and braces. Shotcrete and rock bolts supported the exposed bedrock. This paper will discuss the design, construction and monitoring results.

By Louay Owaidat

The United States Army Corps of Engineers (USACE) Sacramento District awarded a $64 million construction contract in February 2020 to the Maloney Odin Joint Venture for 3 mi (4.8 km) of levee improvements along the Sacramento River East Levee (SREL). This project kicked off approximately $1.5 billion of work to upgrade levees along the American and Sacramento Rivers and widen the Sacramento Weir and Bypass. The project received the 2021 ASCE Region 9 Project of the Year Award. Contract 1 improved levees along five segments of the river, the longest segment being a 2 mi (3.2 km) reach from Garcia Bend Park to the Freeport Intake Facility in the Pocket neighborhood of Sacramento.

Oct 1, 2022

By W. G. K. Fleming

The codification of foundation design and construction is a subject of extensive discussion in Europe and all current code proposals are based on limit state partial factoring. For simplicity, it is claimed, simplified forms of Partial Factor use are presently being advocated but, if this is the direction which codes are to follow, then it is preferable in this age of computer technology that a true system should be adopted rather than a simplification. A philosophically satisfactory method can readily be found which can fulfilcurrent requirements and it is better that such a method should be adopted from the beginning rather than later to find it necessary to make important alterations and amendments.

Jan 1, 1996

By R. Chowdhury

The relevance of reliability studies for deep foundations is considered in this paper with special reference to pile foundations. Attention is drawn to uncertainties related to applied loads, the load-carrying capacity and the safety margin of a pile foundation. The essential steps in a reliability study are outlined. An essential goal of any study is the determination of the Reliability Index or Safety Index under different conditions of loading and operation. Calculations concerning probability of failure or success require an assumption to be made concerning the probability distribution of the safety margin. The significance of this and other assumptions should be clearly understood. Reliability approaches should be used to complement conventional deterministic studies.

Jan 1, 2010

By S. P. Lin

The numerical models of nonlinear piles for deep foundations are studied in this paper. The purpose of these is to clarify the mechanical behaviour of deep foundation nonlinear piles subjected to axial and lateral loadings. Based on the site data of p-y curve as well as t-z curve of foundation soils, it is possible to evaluate pile performance under above mentioned loads by means of combined FEM/FDM models. Numerical examples are presented in tall building and offshore jacket for illustrating the technique, it show high efficiency of these models. Some information to be interested by design engineers are given, especially for those who pay very concerns on the interaction behaviours of structure and its pile foundation.

Jan 1, 2010

By Leena Korkiala-Tanttu, Ilkka Vähäaho, Juha Forsman, Paavo Lahdenperä, Kalle Rantala, Osmo Korhonen

"District of Arabianranta (Helsinki, Finland) has been founded on an old seabed, which was filled with miscellaneous soil materials. The subsoil consists of very low shear strength clays and organic clays (gyttjas). The soil was moving towards the sea at a rate of 1050 mm/year, because of filling on top of the soft subsoil. In the middle of 1990’s it was decided to build a residential area to Arabianranta, because it is located only 5 km away from the downtown. To inhibit the movement of soil, it was planned to build this 700 m long deep mixed column-wall barrier along the shore of Arabianranta in the years 1997–2005. A lot of instrumentation and inclinometers were analyzed and it was noticed that the column-wall remains at its place and the displacement rate inside the wall has been only 0.44.6 mm/year after construction works. Nevertheless, the displacement of soil at the landward side of the column-wall is still 1.25.1 mm/year. The soil at the seaside of the barrier is also moving towards the sea 12.922.2 mm/year. Another problem might be displacements of soil near the places where the column-wall ends (tails).1. INTRODUCTIONArabianranta district (Helsinki, Finland) has been an industrial, storage and wasteland area for a long time. Developing this area into a residential area was earlier considered too expensive, so it has been constructed during last decade. The organic clay layers (gyttjas), which have weak shear strength and high water content, were covered by various layers of fillings done in different phases. Because of the fillings, the area was not only consolidating, but also moving horizontally 1050 mm/year towards the sea due to the fact that the frictional soil under clay layers slopes towards the sea. A trial deep mixed structure was constructed in 1997 to inhibit the horizontal displacements of soil. The actual construction of the columnwall was completed in 2000-2005 with overlapping deep mixed cement columns on the seaward boundary. The barrier was built so that the horizontal movements would not risk the pile foundations at Arabianranta. The length of the barrier is about 680 m and width varies between 1220 m. There is a great amount of instrumentation near the barrier (inclinometer casings and other measuring devices). All this measuring information has been collected and analysed at 2014 to find out how this deep mixed column-wall has affected the horizontal displacements."

Jan 1, 2015

By Burt G. Look, David W. Lacey

"Certification of foundation capacity during the construction phase is often assessed by strength or weathering state descriptors based on visual observations. This case study used the Point Load Index (PLI) test as a quantitative tool in the construction certification of a pile’s design capacity. Construction phase tests were completed on irregular sized rock samples whilst comparable design phase testing was completed on intact rock core samples. Statistical comparisons were made to assess the repeatability between the PLI tests, with best-fit Probability Distribution Functions (PDFs) determined for both datasets. Pronounced differences were observed based on the PDF adopted to characterize the PLI dataset, the consequence of which would be a significant change to the pile’s design capacity. The adoption of the lower quartile value is shown to satisfy both design conservatism and construction simplicity requirements. The commonly held belief that rock samples produced during socket excavation may be biased towards the higher strength portion of the rock mass, is shown to be invalid for this site. As the central bridge piers were certified using Plate Load Tests (PLTs), the resultant load-settlement relationships were compared with the PLI strength assessments made for similar materials recovered from the adjacent abutment piles.INTRODUCTIONThe upgrade of the Foxwell Road Overpass across the Pacific Motorway in South East Queensland required the duplication of an existing four span bridge structure. The foundations of the new bridge included the installation of 1.2m diameter cast in place (bored) piles at the bridge abutments and 900mm diameter cast in place (bored) piles below a retaining wall to be constructed adjacent to the existing abutment.The site geology was dominated by the Palaeozoic Neranleigh–Fernvale Beds, predominantly comprised of argillite, sandstone and greywacke. Limited soil materials existed at the site, with Extremely Weathered (EW) rock typically encountered within metres of the existing ground surface. The exception to the existence of shallow rock were locations where existing filling of the site had occurred – i.e. approach embankments to existing bridge structure.Capacity of pile sockets is typically assessed onsite by descriptive rock strength or weathering assessment. Such descriptors encompass a wide range of values and lack precision. Due to the subjectivity of such assessment techniques – a factor of 3 is often observed in terms of strength assessment based on one’s interpretation of rock strength descriptors alone – uncertainty on site often occurs regardless of whether a lower bound, average or other characteristic design parameter applies."

Jan 1, 1900

By Patrick E. Durnal, Henrik Dahl

"A joint venture of Ben C. Gerwick Inc., Sverdrup (now Jacobs) and DMJM (now DMJM + Harris) designed the $779 million seismic upgrade of the Richmond - San Rafael Bridge over the San Pablo Bay in the San Francisco Bay Area and provided construction support to Caltrans. Construction of the marine foundation retrofi t was completed by a joint venture of Tudor Saliba/Tidewater/Koch-Skanska and their subcontractors: Pomeroy Precast Construction, AGRA Foundations, Dutra Construction and Vortex Divers. Construction management and inspection was performed by Caltrans with the support of various consultants. MARINE FOUNDATION RETROFIT SCOPEThe retrofi t design of the submerged foundations included:??A total of 476 tension and compression micro piles (290- 1140 kips or 1290-5071 kN) installed through cored holes through the underwater bells at 31 pier locations??Fourteen 126/150/164 inch (3.20/3.81/4.17m) diameter CISS (Cast-in-steel shell) concrete shear piles (1160- 2660 kips or 5160-11832 kN) installed through new precast concrete pile cap extensions??Twelve CIDH (Cast-in-drilled-hole) shear piles (1060- 2130 kips or 4715-9475 kN) with 150 inch (3.91m) diameter steel shells to top of bedrock and 30 ft (9,14m) long and 11 ft (3.35m) diameter rock socket installed through new precast concrete pile cap extensions The specifi ed post bid test boring revealed deeper bedrock at one pier location allowing deletion of the rock socket. Thus 15 CISS and 11 CIDH shear piles were installed at 11 pier locations - 9 piers with 2 piles and 2 piers with 4 piles. Cut off elevations for the shear piles ranged from 46 ft to 60 ft (14.0m to 18.3m) below mean sea level and cut off for the micro piles was 8 ft to 46 ft (2.44m to 14.0m) below mean sea level. Almost all foundation retrofi ts required work under limited headroom conditions. Underwater construction connections required innovative design details and construction techniques for each pile type. The 11 piers had 22 precast concrete pile cap extensions installed in pairs and connected by either tremie concrete closure pours or by large pipe struts. The precast pile cap extensions were strapped underwater using large steel bands wrapping around the belled piers with grouted annulus. The precast pile caps were founded with 14 inch (355mm) diameter steel pipe piles, which were either support piles or seismic tension and compression piles. The seismic piles were connected in grouted corrugated steel pipe sleeves cast into the new concrete pile caps."

Jan 1, 2007

"Standing 92 stories high and just over 1,362 ft tall, Chicago’s Trump International Hotel and Tower is perfectly positioned at the center of one of the world’s most impressive skylines.The Tower serves as a link between its famous predecessors, Willis Tower (formerly, the Sears Tower) to the south and the John Hancock Building to the north. Originally planned to be the world’s tallest building, the project was scaled back when the developers started questioning the need for super-tall buildings after the September 11, 2001 terrorist attacks. In its River North neighborhood, Trump Tower dominates the skyline as a symbol of Chicago’s last great building boom, standing triumphantly over other high-profile projects that have been postponed due to current economic realities.It is often said that the three most important factors in real estate are location, location and location. This maxim was not forgotten by The Trump Organization when the site was selected for the International Hotel and Tower. Located two blocks west of Michigan Avenue and Chicago’s famed Magnificent Mile, the site is bound by the historic Wrigley Building to the east, Wabash Avenue to the north and west, and the Chicago River to the south. The building’s position along a bend in the Chicago River allows visitors and residents unobstructed views to the mouth of the Chicago River and Lake Michigan. Site ChallengesUnderneath the site there are approximately 10 to 20 ft of sand and urban fill underlain by soft Chicago blue clay. At 75 ft in depth, the soft clay transitions into Chicago hardpan, a very hard till that was consolidated by the glaciers over 10,000 years ago. Below the hardpan, the till turns granular with cobbles, boulders and water under pressure. Bedrock is about 100 ft below existing grade and has a weathered surface with fractures and clay seams. Unweathered limestone bedrock is sound and hard with unconfined compressive strengths of 10,000 to 20,000 psi."

Jan 1, 2009

By Camilo A. Alvarez, Stephen K. Harris, Brian R. Zuckerman, Philip J. Meymand, Danielle M. Steinmetz

"The sleek new air traffic control tower at the San Francisco International Airport stands at 221 feet tall and is set to replace the existing air traffic control tower by 2016. This aluminum-clad, torch-like structure and three-story Integrated Facilities Building at the base are situated between Terminal 1 and Terminal 2 adjacent to the tarmac. Berkel & Company Contractors, Inc. and Simpson Gumpertz & Heger Inc. worked in conjunction with structural engineers from Walter P. Moore Engineers and Consultants, geotechnical engineers from URS Corporation, architects from Fentress Architects, and general contractors from Hensel Phelps Construction Company on the performance-based design of a foundation to support this critical facility, which is located in a high seismic zone and situated on the very soft soil of the San Francisco Bay margin. With the loading demands and performance criteria established and Young Bay Mud thicknesses ranging from 44 to 47 feet thick across the site, the design team employed a total of 214 24-inch diameter Auger Pressure Grouted piles, which were drilled into the underlying Franciscan Formation as deep as 148 feet below existing grade. Pile reinforcement included full-length confined cages.The piles were designed to resist Maximum Considered Earthquake axial demands as high as 1,400 kips in compression and 700 kips in tension. The performance-based pile design included verification of shear capacity under double-plastic-hinge flexural mechanisms, verification of pile ductility via non-linear moment-curvature analyses, and consideration of curvatures due to kinematic as well as inertial loading.The team implemented an extensive pile load test program including a full-scale static compressive load test on a sacrificial test pile and five non-destructive high-strain dynamic load tests, four of which were performed on indicator piles that were later used as part of the foundation system. These piles were monitored with extensive embedded instrumentation throughout their length, including strain gauges and accelerometers."

Jan 1, 2017

By M. England

Test equipment has been developed to record automatically both the displacement of the pile head and the load applied during a conventional maintained load pile test. Some systems also have, in addition, been fitted with the facility for maintaining the applied load, as set by the operator, at very constant levels. The advantages are both commercial and technical, but a well trained operator has to be in attendance to control the test. Since typical test specifications in the UK require more than 19 hours to complete, it became inevitable that at least one equipment operator remained on site to expedite the test for its duration. Although electronic measurement and data logging of load tests may be more safe than previous direct observation of dial gauges. A single person remaining on a construction site alone is not to be recommended, even if they are just supervising the test. Further development of the testing system produced equipment which will perform the entire test specification as required without operator intervention. To achieve this, full automation is employed. The patented method particularly addresses the safety requirements and by using additional sensors, detects any uncharacteristic behaviour of the pile under test or of the reaction system and the equipment takes appropriate action in a controlled and safe manner. The quality of test data returned from these automated systems is a key element when analysing pile behaviour with models such as CEMSOLVE? and TIMESETTM. These analysis methods often indicate ground disturbance resulting from installation technique and have allowed pile design to be optimised using actual field data rather than theoretical considerations alone. An additional feature is remote access, this allows the data recorded to be transferred and the progress of the test to be viewed from practically any location. This permits experts to view the data 'live' and allows rapid diagnosis of any problems with the expected pile behaviour.

Jan 1, 2002

By David Peterson, Terry Tucker, Rafael Serrano

"The Alameda Corridor-East (ACE) Construction Authority awarded a $172.6 million contract to Walsh Construction Company (Walsh) for the construction of a 2.2 mi (3.5 km) long grade separation including a 1.4 mi (2.3 km) long trench that will allow Union Pacific Railroad (UPRR) and Amtrak passenger trains to operate below ground through the city of San Gabriel, Calif. The project is necessary as the ACE trade corridor accommodates approximately 60% of the shipping containers that move from San Pedro Bay, the busiest port facility in the western hemisphere, to the rest of the country via an extensive rail network. Rail traffic is expected to increase by as much as 160% by 2020, and the resultant delays to vehicular traffic is projected to increase by an estimated 300%. The San Gabriel Trench Project is designed to mitigate the effects of this increased train and vehicle traffic throughout the San Gabriel Valley. Malcolm Drilling Company (Malcolm) was selected by Walsh to perform the specialty foundation and ground improvement work for the San Gabriel Trench.This project is part of ACE’s program to create 22 grade separations and safety improvements at 39 grade crossings throughout the San Gabriel Valley. In addition to safety improvements that will eliminate crossing collisions and delays to emergency responders, the project will reduce vehicle congestion and emissions from passenger cars and trucks having to wait for passing trains, and the project will also reduce locomotive horn and crossing bell noise to local residents.Construction of this portion of the project began in late 2012, and it is scheduled to be completed by the end of 2017, having created approximately 9,000 jobs during this period. The project is being funded from Proposition 1B transportation bonds approved by California in 2006, the Metropolitan Transportation Authority (MTA) Measure “R,” and other local and federal funds. The overall project cost is estimated to be $313 million."

Jan 1, 2017

By W. J. Kingwell

My comments and questions are addressed to Mr. Troughton. It seems to me that the tests were very well tailored to determine long term effects on performance of bearing piles as groundwater pressures rise in the London Basin. This rise is being simulated by means of a groundwater recharge system but it would be informative to have further details of the controls of conditions simulated. Ideally the porewater pressure in Standpipes 1, 2 and 3 should be the same throughout the test. Under test conditions are there not practical dif­ficulties? Recharge Well C2 is a lesser dis­tance from the pile than the other wells. Was the rate of recharge to C2 regulated to a lesser rate than the other three? In my experience the rate of acceptance usually varies from well to well. Under a common feed pressure were mea­sures taken to compensate for this? Since the problem does not only affect London, but also Liverpool, Nottingham, Birmingham and to a lesser extent, Manchester, I question whether an ideal procedure is being used. It is well known that rates of acceptance decrease with time and often recharge wells need to be flushed out at regular intervals. Other pro­cedures may need to be adopted to accurately simulate the effect of groundwater rise, if tests of longer duration are to be considered.

Jan 1, 1991