Search Documents

By G. Tamaro

The World Financial Center is situated on a 60,000 square meter site at Battery Park City at the southern tip of Manhattan Island. The foundations for the buildings and the related infrastructure posed difficult design and construction problems since the site was filled land in the Hudson (North) River. Foundation construction was made difficult by both the geology and the existence of two railroad tunnels which passed under the site. The soils at the site were unsuitable to support construction of heavy structures, and as a result, all of the foundations had to be carried down to bedrock, or the glacial till over rock. Two buildings were supported on piling and special battered caissons which provided lateral support against wind loading. The other two buildings were supported directly on rock, requiring excavation to depths of 19 meters (63 feet) below grade.

Jan 1, 1989

By Jim Frazier

Tradition has often dictated low design load stresses on piles. Such traditions often developed prior to modern static or dynamic pile testing methods and perhaps result from a few limiting situations. These low stress limits were then broadly applied, even in cases where the piles could carry substantially higher loads. With sufficient testing to prove the design, higher design loads may present significant overall savings to the project owner. The cost of the testing then becomes an insignificant cost compared to the potentially great benefit of increased pile loadings. To confirm higher load possibilities for driven piles, the pile is tested either statically or dynamically. Further savings and increased testing efficiency result from remote dynamic pile testing. This paper presents a project where design stresses were considerably increased as a result of additional testing and use of remote dynamic pile testing equipment.

Jan 1, 2002

By Mike Muchard

STATNAMIC load testing augmented with embedded instrumentation has been successfully used to obtain structural and geotechnical design information on large diameter spun cast concrete cylinder piles on many large marine construction projects. The paper focuses on one particularly interesting large marine project involving a new bridge to St. George Island, Florida where instrumentation and STATNAMIC load testing was used in conjunction with static load testing on high capacity piles. The information presented includes embedded instrumentation measurements taken during pile fabrication (post-tensioning), during pile driving, during static load testing, and STATNAMIC load testing. As much of this data is the first of its kind on concrete cylinder piles, it is exciting to present the foundation industry with this additional insight as to the behavior of this pile type and the accuracy of the methods used to test them.

Jan 1, 2005

By Mohamad Hussein

Low strain dynamic tests are performed to evaluate the structural integrity of driven or cast-in-place concrete piles. This type of testing requires minimal pile preparation, and is simply performed by attaching an accelerometer to the pile head and striking the pile head with a hand held hammer. The measured data is processed by a dedicated system, inspected for wave reflections, and interpreted based on one dimensional wave propagation theory. Piles are normally tested shortly after installation so that problems can be identified early and corrective measures taken before construction of the superstructure. However, evaluation of existing foundations is occasionally required. Often, pile installation records are not available rendering impossible any rational foundation reanalysis. This paper discusses three case histories where low strain dynamic measurements allowed determination of pile lengths and structural integrity under existing structures where pile heads were not accessible.

Jan 1, 1992

By Edmund J. Cardoza

The Detroit Water and Sewerage Department (DWSD) provides water and wastewater services to the Greater Detroit Metropolitan Area. Sewerage is treated at the DWSD Wastewater Treatment Plant (WWTP) located at 9300 W. Jefferson Street south of the City of Detroit, Figure 1. PARTICIPANTS Engineering and design of the project for the DWSD was performed by Harza Engineering Company, Inc., C.C. Johnson & Malhotra, P.C. and their sub-consultants, including Worley Engineering and Wade Trim. The Prime Contractor is a Joint Venture of Traylor Brothers, Inc. and Jay Dee Construction. The shaft drilling and riser installation was performed by The Millgard Corporation in joint venture with the Prime Contractor (MTJD). The selection of specialized drilling equipment and the supervision and performance of the access shaft and riser installations was primarily the responsibility of The Millgard Corporation (TMC).

Jan 1, 2001

By Jeffrey A. Gebhard

As part of the design and construction of the new St. Anthony Falls I-35W Bridge, a full-scale load test was conducted on a 6 1/2-foot diameter drilled shaft in the St. Peter Sandstone. This load test helped identify shaft-rock interaction properties, including end bearing and multiple zones of differing shaft resistance for design of the drilled shafts beneath the three piers adjacent the river. The load test was designed by Load Test, Inc., Braun Intertec and the design team of Figg Bridge Engineers/TKDA and constructed by Design Build Consortium of Flatiron/Manson. Oversight was provided by the Minnesota Department of Transportation. Based on these test results, the drilled shafts supporting the St. Anthony Falls I-35W Bridge were designed to reduce risk and maximize economy for the people of the State of Minnesota.

Jan 1, 2009

By K. S. Ho

With the aid of the advanced electronic devices and micro-processors, the quality control of deep foundations can be carried out by Non-Destructive Tests (NDT). Three methods are presented here: the Sonic Logging, Vibration and Stress Wave Analysis Methods. The principles, equipments used, testing procedures and applications are fully described. The correlation of these methods with the conventional tests (mechanical coring and loading test) are studied to give a better understanding of the methods. Several case histories with the test results obtained from a number of sites in Hong Kong and overseas are discussed to show how the pile quality can be examined and especially, how to confirm the effectiveness of remedial works on a defective pile. Recommendation on the percentage of piles to be tested are given at the end of the paper by using statistical method.

Jan 1, 2010

By Mike Muchard

STATNAMIC load testing augmented with embedded instrumentation has been successfully used to obtain structural and geotechnical design information on large diameter spun cast concrete cylinder piles on many large marine construction projects. The paper focuses on one particularly interesting large marine project involving a new bridge to St. George Island, Florida where instrumentation and STATNAMIC load testing was used in conjunction with static load testing on high capacity piles. The information presented includes embedded instrumentation measurements taken during pile fabrication (post-tensioning), during pile driving, during static load testing, and STATNAMIC load testing. As much of this data is the first of its kind on concrete cylinder piles, it is exciting to present the foundation industry with this additional insight as to the behavior of this pile type and the accuracy of the methods used to test them.

Jan 1, 2013

By Harald P. Ludwig, Matthew J. Niermann

The support of excavation (SOE) for the Capitol Crossing project in Washington, DC consisted of a combination of soldier piles, lagging, tiebacks, braces, underpinning, single auger soil mixed (SASM) walls, micropiles, and a tiedback slurry wall. Over 130,000 square feet of SOE was installed with more than 1,300 tiebacks providing lateral support for excavation depths of up to 72 feet. Several structures including the Holy Rosary Church, the Bell Tower, the Casa Italiana, and a modern office building were supported by a combination of conventional hand dug underpinning pits, bracket piles, and stiff SASM walls. This paper will focus on the design and performance of the SOE adjacent to the Holy Rosary Church and the Bell Tower. Deflection-based design was used to estimate the movements of and limit damage to these structures. An extensive monitoring program was used to provide real time movement data. The results of

By Timothy C. Siegel, Derrick Dasenbrock, Rich Lamb, Paul J. Axtell

"The axial resistance provided by deep foundations may be divided into two components: side resistance and tip resistance. The direction that the side resistance acts depends on the relative movement between the deep foundation and the adjacent soil. That is, when the foundation moves downward relative to the soil, then the side resistance is positive and acts upward. Conversely, when the soil moves downward relative to the foundation the side resistance is negative and acts downward. Research supports that both positive side resistance and negative skin friction develop in essentially all deep foundations. The side resistance distribution is a function of the soil strength and stiffness, the applied top loads, and whether the top load is sustained, transient, or a combination of sustained and transient loads. Consideration of drag load and downdrag has become more convoluted with implementation of geotechnical aspects into the AASHTO LRFD Bridge Design Specifications and its use of load and resistance factors. This paper examines the current AASHTO Specifications and presents an alternative design approach for drag load and downdrag using the LRFD framework. The alternative design approach is illustrated by two examples involving drag load and downdrag.IntroductionThe axial resistance provided by deep foundations may be divided into two components: side resistance and tip resistance. The direction that the side resistance acts depends on the relative movement between the deep foundation and the adjacent soil. That is, when the foundation moves downward relative to the soil, then the side resistance is positive and acts upward. Conversely, when the soil moves downward relative to the foundation the side resistance is negative and acts downward. Research supports that both positive side resistance and negative skin friction develop in essentially all deep foundations. The side resistance distribution is a function of the soil strength and stiffness, the applied top load, and whether the top load is sustained, transient, or a combination of sustained and transient.Consideration of drag load and downdrag has become more convoluted with implementation of geotechnical aspects into the LRFD Bridge Design Specifications and its use of load and resistance factors. This paper examines current LRFD design specifications and presents an alternative design approach for drag load and alternative design approach is applied to several examples where drag load and/or downdrag may control design."

Jan 1, 2015

By Lance Rasband, Richard Hanke

"Seattle Tunnel Partners (STP) started mining on Seattle’s SR99 tunnel on July 30, 2013, working slowly through a 15 ft (4.6 m) thick fiber-reinforced concrete headwall. Once through the headwall, the machine would move through roughly 400 lineal ft (122 m) of jet grout-improved soil at a rate slightly over 6 ft (1.8 m) per day. It was anticipated that once through the improved area, Bertha—the world’s largest tunnel boring machine—would move at a rate of 35 ft (10.7 m) per day. By the end of October 2013, Bertha had mined roughly 430 ft (131 m), averaging 4.73 ft (1.4 m) per day, and had begun mining within native soils. By the start of December 2013, tunneling reached the 800 ft (244 m) mark and Bertha averaged 12 ft (3.7 m) per day, achieving as much as 42 ft (12.8 m) of progress on some days. However, on December 6, 2013, Bertha began to stumble and all progress quickly came to a halt. Preliminary InvestigationInitial reports stated that an obstruction had stopped the machine in its tracks. Malcolm Drilling received an early morning call on Sunday, December 8, 2013, from STP to rapidly mobilize a Bauer BG-50 drill rig with crews to investigate what was hindering Bertha’s progress. Malcolm’s equipment and crews flew into action and were completely mobilized and operational by mid-week. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic head within the ground around the machine and allow STP personnel to inspect the cutter head from within the shaft for presence of obstructions. By the close of December 2013, the wells were installed and the dewatering system was fully commissioned. STP crews were then able to inspect the cutter head and found small fragments of a steel pipe wrapped around the outside of the shield. The steel was apparently from an abandoned 10 in (0.25 m) diameter monitoring well casing previously installed by WSDOT (Washington State Department of Transportation) to monitor groundwater conditions for the design and planning of this very project. After the steel was cut out of the head and cleared from Bertha’s path, she attempted to move forward but was only able to manage a slow crawl"

Jan 1, 2015

By Barritt Lovelace

Collins Engineers has been researching and implementing the use of drones on Civil Engineering Projects since 2015. Applications include bridge inspection, asset management, mapping, construction site management and emergency response. Recently this technology was used to map and model construction sites with deep foundations to verify and quantify designs. The ability to collect and use large amounts of data is transforming our world. Drone hardware and software is being used to capture and digitally replicate assets, giving owners unprecedented ability to visualize and manage their projects. Our teams help owners collect and process drone data into deliverables to be analyzed, annotated, stored, and shared. The use of drones can transform the way projects are managed and can improve project workflows. Data collected with drones can be processed into a digital twin of any project site or asset. This digital twin provides owners with a three-dimensional geometrically and geospatially accurate model. These models can be annotated and tagged with information that can be stored and shared locally or on cloud-based platforms. The data can be exported and used in a wide variety of CAD and GIS platforms. Goals When considering the use of UAS for several items need to be considered when establishing project goals. Safety Drones can be used to reduce job site safety risks in two ways. The first is that use of the drone can remove personnel from harm’s way. Surveyors and other project staff will traditionally walk the site to collect survey and other site information. These efforts can be replaced with the use of a drone eliminating much of the need for personnel to be on the job site itself which improves safety. The other way safety can be improved is that a digital model of a job site can be created on a daily or weekly basis that can be quickly analyzed for safety hazards. This analysis could be done remotely by safety officers to identify job site hazards which can then be corrected before injuries happen. Improved Deliverables Perhaps the most important reason to incorporate drones into project workflows it the ability to improve the project deliverables. Drones have the ability to quickly collect large amounts of high quality data which can be processed into orthomosaics, point clouds and 3D models that give engineers and project managers the information they need to make better decisions on design or project management.

Jan 1, 2019

By Mark R. Svinkin

Construction vibrations may adversely affect surrounding buildings and their effects range from human discomfort and disturbance of sensitive devices to visible structural damage. There is no unique conclusion regarding the effect of construction vibrations at every site. Measurement is usually made to monitor vibrations and control them with the vibration thresholds for disturbance of sensitive objects as well as damage to structures. To prevent potential litigation and mitigate the vibration effects on sensitive devices, people and structures, it is necessary to manage and minimize vibration problems before the beginning of construction activities or installation of vibrating machine foundations, and during construction. Pre-construction damage survey and engineering vibration investigations, including the prediction of anticipating vibrations, have to be made at most construction sites in advance of construction activities. Vibration monitoring and control have to be provided during construction. The instrumentation feedback of vibration prediction, monitoring and control provide the basis for choice of measures to prevent or mitigate vibration problems and settlement damage hazards.

Jan 1, 2002

By Michael H. Wysockey

The load test program for the pile foundation at Soldier Field included static and dynamic load tests at four locations around the site. The dynamic tests were run with no knowledge of the static results, and comparison between the two is very good. It was necessary to use a special testing hammer (not the production hammer) to demonstrate capacity with dynamic testing. Over 90% of the piles were HP14x89 with a design load of 230 tons (18 ksi). The load tests showed a capacity in excess of 590 tons for all tests where sufficient set up time was allowed. The remainder of the piles were mostly HP 12x53 with a design load of 100 tons (13 ksi). The measured capacity of these piles was typically about 250 tons. One experimental HP12×74 pile with a nominal yield of 65 ksi held 730 tons (67 ksi) before failing.

Jan 1, 2002

By Yin Zongze

The pile foundation of Sutong bridge pylons is an extra large pile foundation. The length of piles is 115m, and the diameter of the piles is 2.5-2.8m. Since the traditional design method may not determine the settlement and capacity reasonably for such a large pile foundation, the finite element method is used to study stress and deformation of the foundation. The interface element is set to simulate the possible slide between piles and soil layers. The hyperbolic model is taken for soils. Parameters are determined from triaxial test first, and then modified by back analysis on basis of in-situ loading test. The computation results show that the axial force of piles changes with the location of the pile. Outer piles support greater axial force and also friction. The settlement will not be greater than 26cm. The stress and deformation of the pile cap, the abutment, are obtained too. The whole foundation is safe.

Jan 1, 2006

By David R. Beadman

The Fleming method is widely used for the analysis and prediction of single pile behaviour under maintained loading. The method does not distinguish between bored and driven piles. Driven piling avoids the need to dispose of spoil from the pile installation and is therefore becoming increasingly attractive. This paper considers the theoretical effects of the possible preload at the base of a driven pile after installation, using the hyperbolic functions as defined by Fleming. The Fleming method is reviewed and the equations and analyses are adapted, using spreadsheets, to allow for a possible preload. The simplifying assumption of the effect of the elastic compression of the pile is also reviewed and a more analytical method adopted to assess the elastic compression. Some driven pile test data is analysed to consider the possible effects of the preload on the performance of a driven pile and to test the theoretical relationships that are developed in the paper.

Jan 1, 2006

By Mehih Demirkan, Kevin Tehansky

Located about an hour drive south from Washington, D.C., the Maryland Transportation Authority (MDTA) contracted with Skanska-Corman-McLean (SCM) to deliver a new Governor Harry W. Nice Memorial/Senator Thomas "Mac" Middleton Bridge, which takes U.S. 301 over the Potomac River, spanning 1.9 mi (3 km) from Maryland to Virginia. The new bridge aimed to improve capacity, safety and access of the roadway and was planned as a four-lane span with deep foundations that would be constructed fewer than 150 ft (45 m) north of the existing alignment of the more than 80-year-old bridge. The new Harry Nice Bridge opened in the fall of 2022 with a design life of more than 100 years, servicing 12 ft (4 m) wide lanes with 2 ft (0.6m) shoulders, doubling capacity, enhancing emergency response, upgrading maintenance and inspection activity access, and featuring lane sharing for cyclists.

Apr 1, 2023

By Hubert Law, Amin Rahmani

This paper evaluates the effects of pile diameter on the initial modulus of subgrade reaction and proposes modifications to the subgrade reaction moduli that are commonly used in the current state of practice based on American Petroleum Institute (API) guidelines. Three-dimensional continuum finite element model of a soil-pile system is simulated under monotonic lateral loadings to develop benchmark data. The benchmark data, which includes small (0.5 ft) to large (10 ft) diameter pile responses, is used to estimate the initial modulus of subgrade reaction for each of the considered pile sizes. The study shows that the subgrade reaction moduli provided by API may underestimate the actual soil stiffness at the soil-pile interface for large diameter piles and may overestimate it for piles smaller than a certain diameter. A simple equation is proposed herein to adequately estimate the initial modulus of subgrade reaction for all pile diameter ranges. The proposed equation is validated by the measurements of full-scale field tests.

By Lawrence Piccagli

This past spring of 2006, BENCOR installed the concrete reinforced diaphragm walls for the COSMOPOLITAN RESORT & CASINO in Las Vegas, Nevada. The project highlights include the excavation of approx. 326.000 square feet of reinforced diaphragm slurry wall with a thickness of 30 inches and a depth of 100 feet using three reverse circulation trench cutters (hydromills) at the same time. The reinforcing steel cages were fabricated on the 8 acre jobsite and approximately 12,000 cubic yards of 4500 psi concrete was placed via tremie. The jobsite logistics of coordinating three trench cutters and three separate desanding/slurry plants as well as the reinforcing steel fabrication and concrete placement all under a very tight schedule was quite challenging. A second main exercise was the execution of a temporary excavation support. As the excavation depths extends between 66 and 72 feet, five to six rows of temporary tieback anchors were required. Anchor lengths range from 43 -83 feet at a maximum design load of 235 kips.

Jan 1, 2007

By Aminul Islam, Vinay M. Kumar

"About 100 Hectares of land reclamation over the very soft to soft marine clay at Uran Creek in Maharashtra is planned. The depth of marine clay varies from 10m to 24m as observed from the geotechnical investigation. The marine clay was treated with Pre-fabricated Vertical Drains (PVD’s) installed from the elevation of +5.5mCD (chart Datum) and preload/placement of surcharge. A Settlement of soft soil mud under the reclamation was monitored using magnetic extensometer (M) and ground settlement maker (S2). These instruments are installed after constructing working platform at around +5.5m CD. Based on the field instrumentation data, the consolidation parameters were adjusted to match the theoretical and actual settlement plot. The author called this approach as “Back analysis method”. The objective of this paper is to present a case study of instrumented preloading treatment for a thick marine clay deposit. The degree of consolidation in clay strata was determined from magnetic extensometer and ground settlement marker data. Authors also determined degree of consolidation as Asaoka method, Hyperbolic method and Back analysis method and compared the results.INTRODUCTIONExpansion of Container terminal with port buildings, rail container depot, roads and utility buildings at Jawaharlal Nehru Port Trust (JNPT) is planned over a reclaimed land of 100 hectares. Uran creek predominately consists of the estuarine deposit of very soft to soft marine clay. They are characterized by low shear strength, very low bearing capacity and exhibit large settlement when subjected to loading. The additional load causes the significant magnitude of consolidation settlement over a considerable period of time. Thus for development projects on top of soft soil, the postconstruction settlement would be of primary concern.To accelerate the consolidation pre-fabricated vertical drains (PVD) were used. Pre-loading procedure was adopted to minimize the post construction total and differential settlements. PVD’s were installed at 1.0m and 1.2m c/c triangular pattern. Locally available borrow material is used as a reclamation material. The reclamation material has been placed over the existing sea bed level by land based method/end tipping method and created the working platform. The level of working platform is decided based on the tide data and it has been selected such that work should be affected during highest high water level. The PVD has been installed from the working platform and subsequently all the field instruments have been installed from the same level. Five different types of field instruments are installed to monitor ground improvement works."

Jan 1, 2017