Search Documents

By Roberto A. Lopez, Eric Lindquist, Jon Bussiere, Dean Iwasa

"The new 11-story U.S. Federal Courthouse building in downtown Los Angeles demanded a cost effective foundation system capable of attaining a strict total settlement criterion of 0.5 inches (12 mm) under high applied loads. A design-build ground improvement system consisting of 3 ft (0.9 m) and 7 ft (2.1 m) diameter deep soil mix (DSM) columns embedded into the relatively soft Fernando Formation bedrock was selected for the project. The DSM columns support applied stresses of up to 8,800 psf from four large concrete core elements that transfer concentrated building loads to a 3 to 6 ft (0.9 to 1.8 m) thick reinforced concrete mat. The soil mixing ground improvement solution provided flexibility by allowing installation of the DSM columns around existing belled caissons left in place from prior structures, and by allowing repositioning of some of the DSM columns to avoid other existing obstructions in the fill. DSM spoils were used to construct a 2 ft (0.6 m) thick load transfer platform on top of the DSM columns. Quality control measures included utilizing equipment outfitted with automated data acquisition systems, performing three full scale load tests, performing daily wet-mix sampling and compression testing, performing full-depth coring and unconfined compression testing on core samples, and using a borehole acoustic televiewer to evaluate the uniformity of the DSM columns where core recovery was problematic. The results of subsurface investigation and the load tests were used to develop 3-dimensional finite differences models for evaluating stress distribution and deformation of the foundation system.INTRODUCTIONThe new U.S. Federal Courthouse building is currently under construction in downtown Los Angeles, California. The new courthouse will be 11 stories tall with one partial below-grade B1 basement level. The building will have four structural core elements that extend from the main building foundation at the B1 level to the top of the structure. The majority of the building loads will be transferred through the structural core elements to a new 3 to 6 ft (0.9 to 1.8 m) thick reinforced concrete mat beneath the central portion of the structure. The foundation pressures beneath each of the core element locations will be approximately 6,200 to 8,800 psf (300 to 420 kPa) with lower foundation pressures at locations farther away from the central core area."

Jan 1, 2015

By Hayel M. El-Naggar, Marawan M. Shahien

"Large capacity piles are important type of foundation elements that are needed in case of high column loads such as in tall buildings with large span between columns. In many projects, especially if the designer uses the concept of one pile supporting one column (Hamza, 2003a & b). The axial capacity of the large bored deep foundations can be further increased by grouting the shaft skin and the base of the pile. The increase in the capacity of the piles due to grouting can be tremendous. Thus grouting appears as an ideal solution for achieving more reliable foundation and greater savings (Littlechild et al., 2000). A data base of pile load tests of instrumented grouted piles is under development in a major study aiming to propose a simple method to estimate the axial capacity of large bored grouted piles. The data base include pile load tests from projects constructed in Egypt and abroad. The main goal of this paper is to analyze pile load test(s) from one project. The tested deep foundations included 1.2 m diameter and 1.5 m diameter piles and a barrette of size 1.0mx2.8m. The instrumentation of the tested piles and barrette allowed for the separation of skin friction and base contributions to the axial load. Further, the contribution of the skin friction of every layer along the pile shaft could be identified. The results of the analysis clarified how base and shaft grouting increased the axial capacity of the pile and decreased the settlements for certain load level compared to conventional un-grouted piles installed under similar conditions.INTRODUCTIONIn recent years, significant research has been carried out to develop new techniques which are suitable to withstand problems in major projects such as high applied loads in high rise building, large spans structures projects and structures designed using the concept one pile supporting one column (Hamza, 2003a & b). Base and shaft grouting of piles are one of these new techniques which aim at decreasing the settlements and increasing the capacity of the pile under axial load that became major requirements in large projects (Stocker, 1983; Mullins et al., 2001; and Hamza, 2015).Base grouting consists of injection grout under pressure at the base of the pile after the concrete is sufficiently hard. Field evidences showed that the ultimate end bearing of base-grouted piles could be as high as 1.5 that of non-base-grouted bored piles (Suckling and Eager, 2001). Further, field evidences was provided by Shahien and El-Naggar (2015) that showed an increase in end bearing resistance due to base grouting reached to 2 to 3 times that of non-base-grouted bored pile. On the other hand, shaft-grouting causes increase in the soil density in the zone which had been disturbed by the pile construction and thereby improves the shaft resistance of the pile. Field measurements by Gouvenot and Gabaix (1975), Stocker (1983), Robson and Wahby (1994), Troughton and Stocker (1996), Byrne et al. (1998), Joer and Randolph (1998), Hamza and Leoni (1998), Littlechild et al. (2000), Hamza and Ibrahim (2002), Hamza (2003 a&b), Hamza (2015) and Shahien and El-Naggar (2015) showed that the shaft resistance of grouted piles could be nearly 1.5 to 5 times that of non-grouted piles."

Jan 1, 2017

By Kirk Ellison, Eric S. Lindquist, Peter Faust, Stephen M. McLandrich

"The 181 Fremont Tower will be an 800-foot high-rise with a 60-foot deep basement located in a dense urban part of downtown San Francisco. The design and construction methods of the subsurface elements navigated a variety of site constraints such as loose fill and soft estuarine soils, shallow groundwater, contaminants, historic obstructions, small work area, proximity of adjacent buildings, and the on-going excavation and build-out of the adjacent Transbay Transit Center (TTC) train box. Design of the approximately 260-foot-deep drilled shafts (some of the deepest foundations ever constructed in San Francisco) was proven by a full-scale load test that provided unique data on the frictional capacity of the deep soil and Franciscan Complex bedrock in the region. Design and construction of the shoring system for the 5-story basement excavation was exceptionally challenging because of the on-going construction for the TTC. To allow for flexibility during construction, hydraulic rams were placed in a transfer waler along the shared TTC shoring wall that could adjust the forces transferred through to the TTC excavation if required. Open and steady communication between the shoring engineer, the geotechnical engineer, and the shoring/foundation contractor was crucial in order to satisfy the complex constraints of this site.INTRODUCTIONThe 181 Fremont Tower is a new build mixed-use tower, currently under construction in the dense urban core of the South of Market District of San Francisco, California. This high-rise will consist of 54 above ground floors with the roof level 700 feet high. Atop the roof will be some architectural features including a spire that will top out at just over 800 feet, which will make it the second tallest building in San Francisco upon completion.The tower is being developed by Jay Paul Company and the architectural design is by Heller Manus. The structural engineer and geotechnical engineer for the project is Arup North America Ltd (Arup). The shoring designer is Brierley Associates (Brierley). The general contractor is Level 10 Construction (Level 10) and the specialty foundation contractor and excavation contractor is Malcolm Drilling Co., Inc (Malcolm)."

Jan 1, 2017

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007

By Junho Lee, Leopoldo Bello, Mohammad Khan

Multiline ring anchor (MRA) was developed as a cost-effective solution for securing floating offshore wind turbines (FOWTs) to the seabed. Since FOWTs are placed in arrays compared to conventional oilgas platforms, the availability of multiple mooring lines attached to a single anchor can make FOWTs economically competitive. Additionally, the MRA can provide a small and light-weight anchor with high resistance to mooring line loads due to its deep embedment depth. The combined benefits of fewer and smaller anchors allow substantial reductions in anchor material, transport, and installation costs. Such cost reductions are critical to reducing foundation costs for the wind turbine, which can comprise well over 25% of the capital costs for offshore wind power development. Since it substantially reduces the required number of anchor footprints, the multiline anchor concept also permits significant reductions in seabed site characterization costs. This study evaluates how potential advantages of the MRA can reduce the capital costs and provide a reliable cost analysis of the foundation component for offshore wind farms.

By Erik M. Westerberg

The Soilex Pile combines a slender shaft, for quick and easy installation, with an enlarged pile toe, for high capacity. The key component is the Expander Body, which is inflated by injecting cement grout when in position. The latest development in the Soilex Pile System results in a reduction of the total cost of Soilex Piles, in many cases values that are competitive with pre­cast concrete piles and displacement piles. Soilex Piles can now be installed on top of a bearing soil layer, instead of 3 to 4 m into that soil as previously required, further minimising the ground disturbance. Soilex Piles achieve high capacity in relatively loose soils, with ultimate loads typically between 1000 and 2000 kN in a sand with CPT qc = 5 to 10 MPa or SPT N= 10 to 20. It is possible to pre-load and proof-load all piles with dynamic testing up to 2000 kN or using built-in jacks, thereby verifying the capacity. The vibratory installation method, which is extremely quick and causes very little soil disturbance and noise, is exemplified by two case histories.

Jan 1, 2000

By Alan B. Wagner

Data from seven instrumented pile load tests in Milwaukee, Wisconsin and two other instrumented load tests reported in the literature, one in Evanston, Illinois and one in Houston, Texas were reviewed. The data were for pipe piles having diameters from 9-5/8 inches to 18 inches, driven to depths between 36 and 96 feet. These data were used to develop a relationship between effective vertical stress and unit side friction and unit end bearing. These relationships were based on readily measured soil parameters, undrained shear strength, Cu, and Standard Penetration Test (SPT) values. This Beta (ß) and Nt approach and four other methods were then used to calculate the bearing capacity of the nine cases analyzed. The results from each of the methods are compared with the measured results.

Jan 1, 1991

By R. H. Wright

This paper describes the design philosophy and methods employed in constructing the foundation elements for the Little Britain Project in the City of London. The Contract is a design and construct package for the foundations of a 3-storey basement which will be built using "top-down" construction techniques and is to be carried out by Fairclough Piling and Marine on behalf of Wimgrove Nominees. The Project includes 8000 sq.m. of diaphragm wall and barrettes 139 No. large diameter piles ranging from 900mm to 3000mm in diameter and up to 45m deep, and 9 No. cruciform barrettes for the heaviest column loads. Major factors influencing the design of these foundations include differential settlement, heave analysis and a fast track construction approach. Little Britain will provide 43000 sq.m. of space in two linked buildings which will bridge a new road joining London Wall to Newgate Street. The foundation contract is well advanced and the building is due for completion in the Summer of 1990.

Jan 1, 1989

By Daniel L. Hanson

This paper presents a case history of the design, installation and performance of a tied-back tangent caisson retaining wall which was constructed as part of the Third Harbor Tunnel project currently underway in Boston, Massachusetts. The Third Harbor Tunnel project consists of a large multi-lane transportation tunnel which is being constructed by the sunken tube method. In this type of construction, the tunnel alignment, slopes and bedding are excavated and installed underwater and the tunnel sections floated over the proper alignment and sunk in place. The tangent caisson retaining wall discussed in this paper was constructed to provide support of the upper portions of the tunnel excavation at the East Boston Portal where the tunnel exited from below the harbor and continued underground on shore. A portion of the tangent caisson retaining wall was also utilized to provide earth support for the barge unloading facility where spoil from the tunnel excavation was transferred to surface vehicles for removal from the site. PROJECT BACKGROUND The tangent caisson retaining wall was constructed by The Millgard Corporation (TMC) as a subcontractor to the Boston Third Harbor Tunnel Contractors, a Joint Venture which consisted of the firms of Morrison-Knudsen Corporation, Interbeton Inc., and J.F. White Contracting Company. The entire project team is listed below on Table 1. The design of the tangent caisson wall system was performed by Hanson Engineering, P.C. (HE) acting as design consultant to TMC. The retaining wall system incorporated a single row of pressure injected earth anchors (tie-backs) as part of the design. The earth anchors were designed and installed by Drill Tech as a subcontractor to TMC.

Jan 1, 1994

By D. V. Karandikar

Contiguous bored piles have been used in the past for retaining the sides of deep excavation. An innovative version of this method was adopted successfully in two prestigeous projects in Bombay in which in a very constricted and congested locality, adjoining seashore at Walkeshwar, 14 m deep excavations with vertical sides were required. 600 mm dia bored cast-in-situ piles were first installed at 1.2 m c/c and subsequently as the excavation proceeded, they were tied to cast-in-situ RCC waling beams. The shear connectors to the beams were pre-fixed to the pile reinforcing cage at specified depths. The pile / waling beam system was anchored into the ground by installing inclined prestressed cable anchors at the designed depths. The waling beams were also used to support the brickwalls, which formed the required backup wall for fixing the tiled water proofing system. Catch-drains were installed behind the brickwalls for relieving the ground water pressure and thus ensuring a very economic design. The adequacy of the system was proven in that where the system was not installed in time, failure of the sides occurred during monsoon. Whereas in the areas where the above retaining system was installed, there were no problems inspite of heavy monsoon and surcharge of construction materials and equipment. The system became a very effective and economic alternative to an anchored diaphragm wall. The paper presents the case studies of these two projects.

Jan 1, 1996

By S. Doombos

To convert the railway-bridge across the Oude Maas between Dordrecht and Zwijndrecht into a vertical lifting bridge, a drastic adaptation of the existing piers is necessary. Extra piles have to be placed quite close to the present piers to bear the extra weight of lift-towers and bridge-sections. This article describes the special technology applied to drive steel tubular piles l800 mm. in diameter and 36 m. in length vibration-free into position. At the same time a method of pile-point-reinforcement has been applied to minimize the settlements.

Jan 1, 1989

By W. Lum

In the U.S., flexible metal pipe culverts are designed by ring compression theory because the pipes are capable of deflecting and deriving side support from surrounding ground. For economy, tunnel liners are often designed as flexible structures that depend on the lateral pressure of the surrounding ground to maintain stability. In this paper, simple formulas are presented to determine the maximum deflection a concrete tunnel liner may assume and the ring compressive strength of the deflected liner. A tunnel can then be constructed to work within these limits. Similar techniques may be used to design concrete pipes.

Jan 1, 2010

By Carl D. Ealy

Work is being done to web enable the FHWA Deep foundation Load Test Database. Originally designed to function in the client server environment via modem, access to the database both for data maintenance and user queries has been upgraded to take advantage of the Internet and current and future information technology innovations. The DFLTD will be part of an Automated Geotechnical Information and Design Aid System, the object of which is to assist those involved with managing and maintaining our nation's highway infrastructure. The system will also meet the needs of university and other research institutions for a statistically meaningful source of high quality data for the development and verification of improved analysis methods, in-situ testing methods, etc.

Jan 1, 2002

By M. England

Keywords: Bi-directional tests, Osterberg cell, O-cell®, static load tests, Timeset® Static load testing, where loads are applied vertically to the top of the pile and often referred to as 'top down testing', has been used for many years and has become a 'standard' test for the world of foundation engineering. The method, although well developed, cannot be used under certain circumstances, magnitude of load being a particular issue. There is a finite limit to the load capacity that can be applied with either kentledge, the use of reaction piles or anchors, and as the loads increase, the costs escalate dramatically. A novel test method seeks to overcome all the associated problems of large scale and restrictive area "top down testing", utilising static load testing techniques. The method requires the foundation element to be divided into two or more sections and these can be loaded axially as required using a portion of the foundation element as a reaction. This paper presents some recent applications and developments in the use and application of the bi-directional testing technique using the Osterberg Cell or O-cell® and outlines some of the many advantages of the system. Recent bi-directional test loads applied to bored piles have mobilised capacities of 279 MN and with flight auger piles up to 25 MN.

Jan 1, 2006

By Arunsiva R., Sivaranan S., Venugopal B., Kumaran M.

Being a rapidly developing country, India is undergoing a massive infrastructure phase change remarkably. The construction industry is already set to boom, but the time and space constraints necessitate the employment of heavy plants and machinery to take the foundations deeper than ever. Operating such machinery on soft or poor ground conditions without a good working platform leads to uncertainties with massive loss of men and machinery. Plenty of such cases can be observed on construction sites across the globe. Unfortunately, forming a temporary working platform is given least to no importance in the construction industry, particularly ground engineering. This glitch can only be addressed through standard guidelines or codal recommendations on designing and implementing temporary working platforms issued by regulatory bodies. The present paper highlights the importance of providing the working platform, existing design method for working platforms such as TWf 2019:02 of Temporary Works forum, Building Research Establishment BR470 and a brief discussion on the design and construction of the geosynthetic reinforced working platform with a case study is also included. A pitch has been made on the importance of Indian codes/guidelines for the design and construction of temporary working platforms. These guidelines will ensure the safety of the men and heavy machinery and, in addition, increase the productivity of foundation construction irrespective of weather conditions and also become part of the regular construction scope.

Sep 1, 2022

By Wolf-R. Under

For improvement of urban traffic infrastructure, the City of Amsterdam is cur­rently constructing the 9.5 km long North-South Metro line passing through the central districts of Amsterdam. Focal section of the project is the Central Station linking the NS Line with the Central Railway Station, the East Metro line, new bus and tramway terminals, ferries and individual traffic. Construction works required for the project are of high complexity and technical standards. They are executed under severe restrictions concerning programming, space, logistics, and impact on the integrity of existing buildings and structures as all existing installations and facilities have to maintain fully operational during the construction period. The paper deals with the main geotechnical features of the project and in particular with the diaphragm wall and bored pile construction at the Voor-plein and the De Ruijterkade sections of the Central Station.

Jan 1, 2006

By Manasi Wijerathna, D. S. Liyanapathirana

"Deep cement mixing is a popular soft ground improving technology that improves the bearing capacity and settlement characteristics of natural soil. When Deep Cement Mixed (DCM) columns are installed attached to each other in a wall configuration, the walls are capable of resisting bending moments and shear forces in the direction transverse to the columns. Therefore, installing DCM walls beneath the embankment slope perpendicular to the alignment of the embankment is a proper solution to prevent excessive lateral deformations of the embankment. Previous research studies have shown that failure patterns of DCM column walls are different to failure patterns of individual DCM column rows, under lateral loads. This study investigates the failure patterns of embankments where DCM column walls are located beneath the slopes, with respect to DCM wall strength, DCM column wall width and the spacing between DCM walls. 2D and 3D numerical models developed using the ABAQUS/standard finite element programme, were used in this investigation. Results show that the DCM wall strength and width of the DCM wall have a significant influence on the failure mode and the critical failure surface of the embankment. 3D simulation results demonstrate that the failure due to soil extrusion between columns was less pronounced in embankments improved with DCM walls, due to the interaction between the DCM walls and the surrounding natural soil.INTRODUCTIONEmbankments constructed over soft ground are highly susceptible to global slope failure and excessive displacements due to combined effects of vertical and lateral loads beneath the embankment slope (Zheng et al., 2009, Han and Gabr, 2002). The overall stability of the embankment can be significantly improved by improving the soil beneath the slope of the embankment using Deep Cement Mixed (DCM) column rows or overlapped DCM column walls (Jamsawang et al., 2015, Larsson and Broms, 2000, Topolniki, 2004, Broms, 1999). According to the literature, the improved ground experience different failure modes other than shear failure, such as separation of columns, overturning, shear failure along the columns or dowel action (Broms, 1999). Some of the failure modes reported by Broms (1999) are shown in Fig. 1. The ultimate failure mode depends on the geometry and the strength of the improved ground (Jamsawang et al., 2015, Kitazume and Maruyama, 2006, Kitazume and Maruyama, 2007)."

Jan 1, 1900

By Achyut Kumar Allady, Praveen Arumughan

NCHRP Synthesis 418 (2011) entitled, “Developing Production Pile Driving Criteria from Test Pile Data” details the occurrence of dichotomy between pile Skin resistance and pile Tip resistance mobilizations at different times for different hammer blows during pile driving operations. With increasing usage of High Strain Dynamic Testing (HSDT) the engineering community started paying more attention to this occurrence of dichotomy resulting in overdriving, pile damage, increased claims, and loss of time. To overcome the dichotomy limitations of HSDT, NCHRP recommends, “the use of superposition to combine the back-calculated tip resistance from a blow on initial drive or from redrive with the back-calculated skin resistance from the early blows at the beginning of restrike”. However, the current practice of external mounted gauges and signal matching for a single blow are unable to evaluate independently the Skin resistance and Tip resistance to achieve the goal of determining the optimum Total Pile Capacity using the superposition. This paper discusses advancements of science and technology with sensors embedded at the pile top and pile tip, the data collected is analyzed by the state-of-the-art FDOT Method to determine Skin and Tip resistances independently for every blow. Independent Tip and Skin resistances each with a Resistance Factor can be summed up to obtain optimum Total Pile Capacity. Additional benefits of determining independent Skin and Tip resistances include obtaining lost skin capacity due to scour, due to pre-drilling/preforming and uplift tension capacity. Furthermore, the benefits of embedded sensors include increased quality control/quality assurance through 100% testing, accelerated construction, life cycle monitoring and asset management.

May 1, 2022

By Chengcan Wang, Jin-Tae Han, Young-Eun Jang

"The waveform micropile is a newly developed foundation type for increasing the bearing capacity with the created shear keys on the pile’s shaft. Analyzing the increment of resistance at the shear key zone is a crucial factor in the design of the waveform micropile. Hence, centrifuge tests were carried out employing six different models, including a waveform micropile in the axial loading condition. The analysis results of the load-settlement curves showed that the waveform micropile achieved a higher bearing capacity compared to the micropile without shear keys. In addition, the test results revealed that the load-settlement relationship was affected not only by the pile shape but also by the locations of the shear keysINTRODUCTIONA micropile is a small-diameter pile, typically constructed with a less than 300 mm diameter. Generally, the micropile’s construction involves drilling, grouting, and insertion of a reinforcement material, such as a thread bar. The micopile can be utilized in a variety of fields for reinforcing the foundations of existing structures. It also has advantages for accessing challenging areas like limited-access construction sites, including those with a low headroom space and adjacent structures, due to the small size of the construction equipment. Thus, since it was introduced in 1950 in Italy, the micropile has become one of the preferred solutions when other deep-foundation methods are not applicable to the site.Federal Highway Administration (FHWA) gives the micropile design implementation guideline of neglecting the end bearing due to its small diameter but considering the frictional resistance if the bond zone of the pile is in the soil or on a weak rock. The bearing capacity is considered primarily only if the micropile is founded on a high-quality sound rock (FHWA, 2005). Micropile design in South Korea is currently being performed based on the FHWA manual and taking into consideration the frictional resistance for the design as the pile generally sockets into a weak rock or soft rock. Moreover, the frictional resistance within the soil layer has usually been ignored, considering only the shaft resistance of the rocksocketed length in the conservative design. The design concept excluding the frictional resistance in the soil layer, however, may lead to an extension of the pile socket length, which will increase the construction cost. Hence, many researches have attempted to provide better design and construction methods to increase the bearing capacity in a cost-effective way (Juran et al. 2001; Sadek and Isam 2004; Tsukada et al. 2006; Finno 2002; Gomez et al. 2003; Seo et al. 2013)."

Jan 1, 2016

AUSTRALIA CHAPMAN Gary JOHN WAGSTAFF CONTSRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE BRISBANE HILLAR Jaaes Director J.A. HILLAR & ASSOCIATES 99 Woolwich Road WOOLWICH, NSW 2110 WAGSTAFF John Managing Director JOHN WAGSTAFF CONSTRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE, BRISBANE AUSTRIA FUCHSBERGER M. TECHNISCHE UNIVERSITAT INSTITUT FUR BODENMECHANIK Rechbauerstrasse 12 8010 GRAZ

Jan 1, 1994