Search Documents

By Mark R. Svinkin

Construction vibrations may be harmful to adjacent and remote structures, sensitive instruments and people. Construction vibration sources have a wide range of energy, displacement, velocity and acceleration transmitted on the ground. Effects of different dynamic sources and soil conditions on construction vibrations is analyzed. Consequences of construction vibrations are developed in various ways. It is important to assess intolerable vibrations before the beginning of construction activities. Guidelines for preconstruction survey are presented. Pre-construction survey and prediction of anticipated vibrations by IRFP method, monitoring and control of measured vibrations are important steps in preventing intolerable vibration effect.

Jan 1, 2000

By Patrick J. Hannigan, Geir Veslegard, Frank Rausche, Rozbeh B. Moghaddam

A common type of deep foundation used in Norway to support bridge structures is the drilled pipe piles (piles) filled with concrete reinforcement after installation. The standard installation practice is the use of down-hole hammers. Complex geology and difficult subsoil conditions in Norway causes a high variability of soil and rock layers which in turn make for differences between actual subsurface conditions and those expected from geotechnical exploratory borings. This situation is strongly noted when the foundations are not fully socketed, and the rock layer is sloped. In this particular case, special testing procedures are required to assess the drilled pile base material and evaluate the rock-socket to ensure full contact between the foundation base and the rock surface. The local standard practice to verify the latter condition, consists of coring and visually evaluating the material recovered at the bottom of the drilled pile. This paper presents a case where the coring and visual inspection were not possible and alternatively the geological material encountered at the base of the deep foundations was evaluated using force-displacement measurements. Two 1016-mm (40in) diameter open-end drilled piles identified as P02-04 and P02-05 were tested and evaluated using in-situ force-displacement data prior to filling the piles with concrete. Test results showed an average displacement of 7mm (0.28in) corresponding to 35MPa (5.1ksi) stress level for P02-04, and 7.2mm (0.28in) corresponding to a stress level of 38MPa (5.5ksi). Based on testing results, both drilled piles were within the established material assessment criterion presented by the local authorities. INTRODUCTION This paper presents a case study in Norway where the material encountered at the base of an open- end drilled pipe pile (pile) was evaluated using force-displacement data. In the deep foundation industry in Norway, it is a common practice to install piles to support transportation structures. Once the piles reach the embedment elevation, and the pile base is assessed, these are filled with concrete. In projects where sloping rock is the supporting layer, and all nominal loads are supported by the pile base resistance, assessing the material encountered at the pile base to ensure full contact with the rock becomes critical. The local practice to make this assessment consists of the use of weighted tape, coring, or inspection cameras. However, similar to any other testing and evaluation methods, these come with their own limitations. The variability associated with the use of the weighted tape, accessibility for the coring equipment to complete a coring process, or the conditions at the foundation base such as murky water or thick drilling fluids could significantly impact the photo or video quality taken at the pile base. In such conditions, it is important to consider alternate testing methods to evaluate the material at the foundation base.

Jan 1, 2018

By Robert Bachus, Jamey B. Rosen

"Abstract Large scale In Situ Barrier Wall Construction projects, specifically those related to earth dams, dikes, and levees, frequently require stringent quality control measures to ensure the success of the wall. This presentation discusses the applications of Geographic Information Systems (GIS) technology to capture information from multiple data streams and provide geotechnical feedback, quality control, and project control feedback. Techniques used to geospatially analyze verticality data from secant piles and panels will be demonstrated. Examples will be presented from barrier wall installations at two sites owned by the U.S. Army Corps of Engineers (USACE): the Wolf Creek Dam in Kentucky, and Center Hill Dam in Tennessee.IntroductionDeep foundation installations require contractors to collect a substantial amount of information over the course of a project, both for internal quality control of construction progress and for demonstrating compliance with customer or owner specifications. Methods of collecting information are constantly improving, bringing with it the need for a systemic approach to managing the increasing amounts and types of data. Handling these diverse types of data presents challenges with both budget and schedule demands. This paper discusses some techniques for adding or increasing quality control in barrier wall constructions by consolidating, visualizing and analyzing data using relational database and Geographic Information Systems (GIS) technology, collectively referred to as Information Management System (IMS) development. The IMS concept is designed to facilitate the collection, transfer and processing of data and provide an easy way to remotely access and visualize construction progress.The remainder of this paper presents the needs and objectives of an IMS applied to quality control in barrier wall construction, the components and data flows involved, the capabilities and user interfaces of the systems and the benefits for the end users. Examples are presented throughout from case study projects including: a pile barrier wall applied in the rehabilitation at the Wolf Creek Dam in Kentucky (under contract to the Treviicos-Soletanche Joint Venture), and a secant pile barrier wall currently under construction in the rehabilitation of the Center Hill Dam in Tennessee (under contract to Bauer Foundations Corporation) (both owned by the Nashville District of the USACE)."

Jan 1, 2014

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001

By Michael D. Justason

This paper details the static and Statnamic load testing on a 600 mm square pre-stressed concrete pile. The pile was located at Pier 15 on the 20 million-dollar Bayou Chico Bridge Project in Pensacola, Florida. The pile was 10.5 meters long and had a design load of 1.3 MN. Three static load test cycles were performed in November, 1996. The Statnamic load test was performed in January, 1997. The Davisson Failure load of the first cycle of the static test was 3.7 MN, and the Davisson Failure load of the Statnamic test was 3.2 MN. The load-displacement curves for the two types of tests were very similar, indicating that the Statnamic load test performed well in the sandy soils. Strain gauges embedded in the pile showed 35% skin friction and 65% end bearing for both test methods. Strain gauges were located at equal spacing at five elevations in the pile. A toe accelerometer verified the rigid body assumption of the Unloading Point Method currently used in the analysis of Statnamic load tests. The data collected from the pile instrumentation was of excellent quality and represents some of the best research to date comparing static and Statnamic load tests.

Jan 1, 1997

By Steni Stefani, Sanjay Dave

"This paper describes an innovative method, used for the first time in India, for the construction of a 1.0metre-thick positive plastic concrete cut-off wall (CoW) at the upstream toe of the dam at the Kishanganga Hydro-Electric Project in Jammu & Kashmir- India. The extremely difficult bouldery geology with an overburden laden with very hard Panjal Volcanics (quartz, feldspar, muscovite and chlorite minerals) boulders of up to 0.8m to 1.8 metres in size with UCS of up to 265 MPa and the requirement of socketing the CoW into the underlying hard bedrock (UCS 265 MPa) for 1.50m made the choice for the excavation methodology critically difficult. After having evaluated several other existing methods – including hydromill trenchers – the Civil Contractor Hindustan Construction Company, in agreement with its Foundations Engineering Consultant (Ricerca e Sviluppo – Cantieri e Gestioni) opted for a two-stage construction method: firstly, preliminary full-depth drilling and “surgical” blasting with full-length inclinometer checking of borehole verticality to ensure the exact location of rock fracturing and fragmentation coincided with the required position and that it was vertical, notwithstanding efficient trenching into the bedrock of a nominal 1m by 1.5m section; and, secondly, excavation by using heavy duty mechanical rope grabs made locally and developed by the Consultant in collaboration with the Contractor. The details of the methodology and the salient construction data is presented and commented for the 33-metre deep CoW installed at a working platform elevation of 2364.50 m above sea level in a very remote area.BACKGROUNDThe Kishanganga Hydro Electric Project (KGHEP) is a ROR (run-of-the-river) project is located on the Kishanganga River some 140kms North-West of Srinagar, capital of Jammu & Kashmir State of India, for generating 330MW of power in a 90% dependable annual year. The key components of the project are: Concrete Face Rockfill Dam (CFRD), Chute Spillway, Plastic Concrete Cut-off Wall (CoW), Head Race Tunnel (HRT), Surge Shaft (SS), Inclined Pressure Shaft (PS), underground Power House and Transformer Hall, Tail Race Tunnel (TRT).The Power House Site is accessible throughout the year from Srinagar while the remote Dam Site, with its tortuous road climbing the Rajdan Pass at 3556m (11,667 ft) above sea level and several 20-tonne capacity Bailey bridges removed prior to snowfall, remains inaccessible for around 4 months between mid-November to mid-May due to winter and heavy snowfall - the only access is by helicopter, weather permitting. Temperature at the Dam Site drops down to minus 27degrees Celsius during winter, therefore, careful planning from the beginning was most essential for the successful delivery of the Project.This paper deals with the Cut-Off Wall construction which was performed, for the first time in India, adopting a “Drilling and Surgical Blasting” method. However, this technology is not new and diaphragm wall excavation with the aid of drilling and blasting has already been done in some of the projects globally; namely:"

Jan 1, 2017

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By Kenneth Gavin

The accurate prediction of the shaft capacity of drives piles in sand continues to present problems for foundation designers. Research in this field has been carried out for many years and has yielded a wide range of design approaches -some of which have been shown by recent experimental work to be based on questionable assumptions. This Paper reviews some of the current popular design methods for piles in sand in the context of recent information obtained from high quality field tests conducted by institutions such as Imperial College London. A database of driven piles in cohesionless soils has been compiled from well documented (and reliable) case histories that have been reported in the literature. The measured shaft capacities of the piles in this database are compared with predictions made by the various methods and an assessment is made of the predictive performance and reliability of each method

Jan 1, 1996

By Frederic Masse

With widespread acceptance in the market place, many engineers are choosing ground improvement techniques to provide suitable foundation subgrade at sites that would have traditionally required deep foundations. This paper discusses the Controlled Modulus Columns (CMC) ground improvement technique and some case histories highlighting the use of this technique for retail development sites. CMC are a sustainable and cost-effective ground improvement technology that transmit load from the foundation to a lower bearing stratum through a composite CMC/soil matrix. The CMC installation is also an attractive option from an environmental perspective because it utilizes reverse flight augers, which displace the soil laterally. This installation technique achieves two goals: it densifies the soil around the CMC, which improves load transfer into the element and avoids spoil and its disposal. Through the introduction of two cases histories, we will present the key benefits of the CMC technology. Each case history will clearly illustrate how a CMC solution can reduce the overall cost of a project when compared to a more traditional type of deep foundations. They will also show how the use of CMCs has benefits that relate to the overall sustainability of the project. While CMCs are an attractive financial and sustainable option, they have also demonstrated that the performance of the system is comparable to that of deep pile foundations. Because CMCs are a relatively new technology many potential users are not aware of its benefits. While we discuss the use of CMCs to support buildings in this paper, CMCs also have been used for a variety of other applications including foundations for tanks, mechanically stabilized earth (MSE) walls, and embankments

Jan 1, 2011

By Charles Pol Vuillier

Piling work for modification to the Charles Grimes Bridge in Melbourne, Australia required piles to be installed through 15 to 20 m thickness of very soft to soft silty clay overlying 10 m of stiff clays and sands in turn overlying siltstone. The presence of an old sewer founded at depth in the soft clays demanded that vibrations be kept to a minimum. Two pile type were used by Vibro-pile (Australia) to provide the client with the most economical piling price. The two pile types were CFA piles of 750mm diameter founded in the weathered rock and a full displacement concrete injected screw pile developed by Vibro-pile called the "Z" pile, founded on the rock. The development and features of the "Z" pile are briefly discussed, including the perceived applications and advantages of the pile type. On board instrumentation comprising a computer was used to monitor all aspects of the construction. The rig instrumentation provided an important quality control measure that gave confidence in the pile installed. Pile performance was proved on the cast in situ piles by dynamic load testing methods. Initially tests performed with a 120 kN drop hammer, which was not capable of mobilising the required loads. The performance was then satisfactorily proved by using a drop hammer of 20 tonne mass delivering blows drop heights of 1.5m. Low strain integrity tests on a number of piles were also used to confirm the structural integrity of the piles.

Jan 1, 2000

By Jason N. Scott

CFA piling is a ?blind? construction process that relies heavily on the rig instrumentation to produce sound piles. If the data measured and recorded during construction can be made available to engineers and managers within hours after construction then there are many economic and quality control benefits that can be realised. A state of the art CFA instrumentation and data management process has been developed in the UK. The key components of the instrumentation, GSM data service and the central database are described. Many benefits to the business have been realised and, where possible, these are quantified.

Jan 1, 2006

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By Robert A. Field

Static-Load Piledriving utilizes a hydraulic push to facilitate the installation of a pile. The pile is not rotated, impacted or vibrated. A smooth pushing force advances the pile incrementally into the ground. Static-Load devices must have a reaction mass to push against. The most simple form of a Static-Load device is a jack; more advanced equipment, such as the Still Worker, also utilizes this approach. This paper focuses on the use of the Still Worker on three challenging projects. In each case, the existing site conditions made it risky, or unattractive, to utilize conventional impact, vibratory, or drilled-shaft equipment.

Jan 1, 1997

By Donald R. McMahon

This paper presents a unique case history that documents the use of a braced secant pile wall to underpin a heavily loaded footing inside of a manufacturing plant. Construction of a pit for a new manufacturing process directly next to the footing necessitated the underpinning. The footing supports an overhead crane that needed to remain operational throughout construction of the pit and therefore, settlement of the footing could not be tolerated. The base of the footing was about 7.7 feet above the base of the 17-foot deep excavation. The footing bears on a silty clay deposit that grades from a stiff consistency beneath the footing to a soft/medium consistency near the base of the pit excavation. This paper describes the design and construction of the secant pile wall and bracing to control wall deformations, ground movements and settlement of the footing. The footing was monitored for settlement throughout construction of the pit and no measurable movement was observed.

Jan 1, 2006

By D. E. Sherwood

Mr. Tamaro introduced his paper which concerned the construction of foundations for the buildings and related infrastructure of the World Financial Center on a reclaimed shoreline site at the Southern tip of Manhattan Island. This large project presented difficult design and construction problems, both geotechnical and structural. All structures were supported by foundations carried to rock. Two of the buildings were supported by conventional pier (pad) foundations constructed within diaphragm wall cofferdams. The remaining structures were supported by either piles to rock or caisson (large diameter) piles with socket depths drilled through the rock of up to 7.6 metres. Underground services, railway and proposed road tunnels all affected the installation of foundations. The proposed road tunnels for the new six lane 'Westway' would involve an excavation 12 metres deep adjacent to and under three buildings. This problem was solved by an agreement that tower windloads would be taken by the tower foundations and not distributed through the basement walls. This was achieved by a system of battered caissons founded on the rock and arranged so that adjacent caissons were founded in different rock masses. Diaphragm walls were restrained using tie backs. Ground testing indicated an exposure to D.C. stray current corrosion of all underground construction. As a result all of the foundations were isolated from the ground by non-conductive materials. In the case of piles and caissons the reinforcing for the caisson was fully protected by concrete and all outside steel used for the installation of piling was considered sacrificial and not used in the computation of long term load carrying capacity.

Jan 1, 1991

By Arturo Ressi di Cervia

The utilization of diaphragm wall construction in Hong Kong began in 1974 with the construction of the New World Center, the first diaphragm wall job built in the British Colony. That landmark job of which I am presenting a few slides and a schematic description, embodied all of the difficulties and problems which are encountered in the difficult geology of Hong Kong. A small rocky island in the South China Sea, Hong Kong provides one of the finest natural harbors in the world. It is its splendid harbor, coupled with the enterprising attitude of the Hong Kong Chinese and the laissez-fair attitude of the British government which has resulted in the explosive growth of this speck of land soon to revert to the political control of mainland China.

Jan 1, 1993

By R. T. Stain

Integrity testing of deep foundations is now common practice in Europe, indeed in the City of London such testing is a contractural requirement on every site. This paper is in two parts: Part 1 describes the most commonly used test methods and their applications. Part 2 presents a case history where both of the above techniques were used.

Jan 1, 1987

By Christian Divis

[ ]

Jan 1, 2002

By Douglas W. Christie

Deep foundations in Washington, DC have played a role in the city?s development since the 19th century. Designers of government and commercial buildings sought deep foundations initially to minimize settlement of structures. As the western portion of the National Mall was made by filling in portions of the Potomac River, numerous memorials and monuments on the Mall required deep foundations. In recent years deep foundations have been used to allow underground construction for various reasons. Commercial developers have sought to maximize the use of sites by developing below-grade space for parking to meet code requirements and offset the limits on building heights. Underground museum and gallery space has been constructed to expand public space while preserving open space above grade. Access and security concerns have prompted the design of underground visitor centers rather than above-grade structures.

Jan 1, 2006

By Vincent Jue

In December 2009, the Italian High Speed Rail Network AV began running over the full 1000 km system length from Turin, at the foothills of the Alps to Salerno, on the seacoast south of the volcano Mt. Vesuvius. It runs through Alpine rivers, highly seismic active zones, mountains, river plains, and through some of the most densely populated areas in Europe as well as some of its most expensive real estate. The Italian High Speed Network?s technical/economic constraints and its regulatory/socio-environmental concerns well may mirror similar obstacles set to confront the nascent California High Speed Rail Program. The two types of constraints must be dealt with together to reach the best construction solution. It is estimated that more than 20% of Italian High Speed Rail Network costs were spent on ground engineering including over 150 km of tunnels, 200 km of viaducts and bridges and 650 km of embankments and trenches. However, it also is estimated that 25% of costs were spent on social and environmental integration of the new rail lines including over 6 square miles of green offsets, 160 km of anti-noise walls, and 300 agreements for socio-environmental work. This paper will look at four examples of innovative ground engineering solutions, each with its own intricate set of constraints: ? Foundation system for viaducts across the ?Po? and ?Ticino? rivers. ? Soil consolidation under railway embankments ? Requirement of short tunnels for physical and environmental reasons ? Construction of railway stations in a confined right of way

Jan 1, 2010