Search Documents

By Amr M. Sallam

A case history of utilizing a mat foundation enhanced with ?settlement-control? piles to support a high-rise building in Downtown Orlando is presented. Original geotechnical engineering studies, performed by others, recommended pile foundations due to difficult soil conditions and highly variable loads. The value engineering study performed by the authors provided alternative foundation system of the mat foundation enhanced by ?settlement-control? piles. The alternative foundation system required few iterations of structural and geotechnical analysis. A target stiffness for the settlement-control piles was selected by the structural engineer. Pile load tests were performed to verify the recommended pile geometry. A total of 81 auger-cast-in-place settlement-control piles 45-foot long 16-inch diameter were installed. A total of 24 columns were monitored for settlement, which showed substantially less settlement than predicted. It is the authors? opinion that the ?settlement-control? piles increased the mat stiffness, relieved the concentration of contact pressures around heavily loaded columns, and reduced potential differential settlement. Mat foundation with settlement-control piles provided border-line foundation solution between shallow and deep foundations and has the potential to be widely used in Central Florida for similar subsoil and loading conditions; however a thorough analysis using three dimensional Finite Element Modeling may be needed to refine the geotechnical evaluations.

Jan 1, 2009

By Inc. Pile Dynamics, Daniel S. Belardo, Marcus Galvan, George Piscsalko

Soil nails are often utilized as a temporary or permanent earth retention technique for slope stabilization and for excavation retention for existing or new structures. Soils nails are generally advantageous as installation is relatively rapid and they can be installed beneath existing structures and where site access for equipment is limited. Due to the typically small cross-section of these elements, the inability to inspect the holes prior to grouting/concreting, and the various installation techniques utilized, quality control for assessing the integrity along the entire length is limited. Currently, quality assurance is conducted by load testing to verify the pull out capacity after installation. The load testing is typically done on a small percentage of the total number of soil nails. This paper will provide the results of a demonstration where the new Non-Destructive Test (NDT) method Thermal Integrity Profiling (TIP) was used to access the integrity of several soil nails along their entire lengths. This TIP method has been successfully used for several years to assess the integrity in drilled shafts and ACIP piles. The TIP method assesses the integrity across the entire cross-section and can identify regions where bulges, necks, and insufficient grout/concrete are present. TIP testing can also help assure that the contractor's installation methods are adequate and consistent for the intended design. For the project presented, instrumented Thermal Wire were affixed to the centered tension bars prior to placement in the excavated shafts. Temperature measurements were recorded from the hydration energy generated after grout/concrete placement, capturing the entire heating cycle. Manufactured defects were installed on the center bar at multiple locations. The results and conclusion will be discussed as well as recommendations for future use.

Jan 1, 2017

By Jason N. Scott

CFA piling is a ?blind? construction process that relies heavily on the rig instrumentation to produce sound piles. If the data measured and recorded during construction can be made available to engineers and managers within hours after construction then there are many economic and quality control benefits that can be realised. A state of the art CFA instrumentation and data management process has been developed in the UK. The key components of the instrumentation, GSM data service and the central database are described. Many benefits to the business have been realised and, where possible, these are quantified.

Jan 1, 2006

By Dempsey S. Thieman

Innovative marine bulkhead design and construction techniques were used in the fast-track design and construction of a high-capacity, deep-water dock in the highly seismic region of Alaska?s Aleutian Islands. The geotechnical investigation and design through construction phases were completed in just eight months. The adaptable OPEN CELL® design, readily available standard flat sheet pile and an experienced contractor were integral to the successful completion of the project. The cost of the structure was determined to be approximately 50 percent of a comparable pile-supported platform dock structure, allowed higher load capacity, rapid construction, less maintenance, and provided substantially more uplands. This paper details the design and construction of this unique and challenging project. The OPEN CELL structure is a vertical flexible membrane system that offers significant advantages over other structure types: ? Its flexible membrane structure is not dependent on toe embedment for stability. ? Poor soil conditions, shallow bedrock, high seismic loads, deep water, scour, etc., can be accommodated due to its adaptable design. ? It has a very high load capacity?capable of several thousand pounds per square foot. ? Allows buried utilities which results in lower cost and reduces freezing conditions ? The sheet pile tail walls can be extended to provide increased global stability if needed. ? Standard sheet pile and connectors with traditional installation techniques allow accelerated construction schedules.

Jan 1, 2008

By Paul Doherty

Expansion of the global piling industry has been coupled with significant research efforts investigating the mechanisms controlling pile capacity. Static pile design has transitioned from total stress approaches toward effective stress design, with associated improvements in predicting pile performance. As a result, the available literature is heavily skewed toward static capacity prediction. However, when considering piles offshore, the majority of loading is not static but highly variable and cyclic in nature. This paper outlines the additional factors that require consideration for cyclic pile design, including elevated loading rates, cyclic displacements and capacity degradation. A review of the literature identified a number of cyclic pile testing programs which are collated in this paper. General trends are established through comparison of the tests within the database and the conditions where cyclic loading is most likely to be a concern are identified. In particular, loading conditions which involve full plastic shear reversals are seen to cause the most extreme cyclic damage, with the degraded capacity as low as 31% of the precyclic static capacity. The underlying mechanisms which can result in cyclic damage are explored, with particular attention given to the pore pressure response, radial stresses, shear transfer and particle reorientation.

Jan 1, 2009

By Emad Farouz

This paper compares the predicted axial capacity of driven Pre-cast Pre-stressed Concrete (PPC) piles for the Lake Gaston Water Treatment Plant (LGWTP) using several design methodologies versus the axial capacity measured from dynamic and static load testing. The LGWTP site is located in Chesapeake, Virginia and is part of the Great Dismal Swamp. The subsurface investigation included soil borings, in-situ dilatometer (DMT) tests, and in-situ piezocone (CPTu) tests. The axial capacity predictions of the PPC piles were performed using the computer programs DRIVEN and FB-DEEP which are based on SPT N-values. Additionally, an empirical method proposed by Martin, et al. (1987) based on local experience with PPC pile design in the Yorktown formation in the Tidewater area of Virginia was also evaluated. Finally, the ?Laboratoire Central des Ponts et Chausées (LCPC)? method developed by Bustamante and Gianeselli (1982) based on CPT measurements was also used to develop the axial pile capacity of the piles. This paper shows that the FB-DEEP computer program and the LCPC method provided a reasonably good prediction of the pile axial capacity measured from PDA, CAPWAP, and Static Load Tests in comparison with the other design methods used. The soils in this area develop significant setup over time and it was found that FB-DEEP and the LCPC method are capable of incorporating this setup in the prediction of the long-term axial capacity of driven piles in this area.

Jan 1, 2007

By Maurice Bottiau

"Abstract When addressing the performance of deep foundations, many parameters play a role, from adequate soil investigation to performance monitoring and testing. The correct understanding of pile construction, though, remains crucial. After a long period of empirical design and regulations, the last decades have been the ones of theoretical considerations and extensive codes writing. The interaction between technology and design, however, still plays a determinant role. The introduction of hydraulics and the exponential increase in available power on one hand, the miniaturization and the introduction of electronics in control and monitoring systems on the other hand have exerted a major influence on new foundation systems or the evolution and control of existing systems. It appears important to try to take execution related parameters and their control during execution more deeply into account when assessing the final result of the deep foundations and the achieved level of safety and reliability. In this contribution, we will try to analyze how systems, equipment and pile production monitoring and testing can influence the pile performance, and if/how this influence could/should be translated in adapted safety or installation factors. This analysis will run through different categories of piles: driven, augercast and displacement auger piles and bored piles. INTRODUCTIONThe global performance of a deep foundation depends on different aspects (Poulos, 2003):1. Ground investigation2. Design and analysis3. Construction4. Testing5. Performance monitoring6. Remediation and performance enhancementThis paper intends to address the importance of pile construction and the control of it on the final performance of the pile-group of piles. There has been an increasing interest for theoretical analysis over the last 20 years, followed by an increasing impact of regulation and codes. Without denying the importance of the latter, the author wants to point out how installation procedure and project specific parameters can largely influence the reliability of the deep foundation. In this context, detailed and prescriptive standards can miss their objective of intended improvement of accuracy and reliability, but even worse they can adversely impact engineering judgment. In today’s construction world, it is possible to gather installation information which can be of outmost importance for the final deep foundations performance. Therefore, the increase or decrease of installation reliability through adequate pile testing and performance monitoring should be emphasized and should be taken into account in the codes. This is the case already in most advanced codes, but in a limited and insufficiently refined way. After reviewing how codes deal with this issue today, we will show some recent examples of unexpected results due to pile installation. We will try to put these examples into a broader perspective by highlighting some reference and/or recent literature considerations. Finally we will try to summarize how pile testing and installation documentation can increase reliability and attempt to open the debate on how codes could/should allow for more engineering judgment."

Jan 1, 2014

By Takefumi Takuma, Hiroyuki Nishimura, Shigeru Kambe

"Japan’s Great Tohoku Earthquake and the immediately following tsunami of March 11, 2011 killed more than fifteen thousand people and destroyed numerous buildings and infrastructures in the northeastern part of the country.In addition to reconstruction projects in the areas where the earthquake and tsunami hit, other seismically vulnerable regions in the country have started building new and more robust facilities as well as upgrading existing coastal structures so they will be able to cope with such deadly seismic and hydraulic force. This paper will highlight two different types of aseismic and anti-tsunami levee upgrades currently under construction on the coast of Kochi Prefecture, approximately 500 miles west of Tokyo. The first type is the installation of double sheet pile walls in existing seawalls. The second type is to drive tubular piles into existing levee structures for reinforcing them. Both sheet and tubular piles are being driven by the Press-in Piling Method without removing or compromising the function of the existing structures. 1. BACKGROUNDGreat Tohoku Earthquake of March 11, 2011 caused severe damage to many structures. ASCE’s survey of damaged coastal structures conducted immediately after the disaster by Ewing, et al. (2014) categorizes failure modes of the structures in the following manner.?Overtopping without structural failure.?Overtopping with structural damage or failure.?Wave uplift forces.?Movement of structure off foundation from sliding, rotation, or overtopping.?Impact loads.?Hydrostatic pressure.?Supercritical flows.?Scour.?Erosion.?Abutments end effects.?Subsidence."

Jan 1, 2017

By Dan A. Brown

Outline ? Basic Concept of ACIP Piles ? Factors Affecting ACIP Pile Performance ? Applications: - Favorable Conditions - Unfavorable Conditions ? Design for Axial Loading ? Lateral Loading Considerations ? Summary & Conclusions

Jan 1, 2004

By Seyyed Mehdi Radeghi Mehrjou

It is important to study structures and their retrofitting techniques in order to avoid earthquake-induced seismic damage within countries that are prone to earthquakes. Todays, micro piles are employed as useful structural components for seismic behavior improvement. The present study analyzes inclined micro piles subjected to seismic loading by using the three-dimensional finite difference method (FDM). FDM assumes an idealized three-dimensional soil-micro pile model to perform logical behavior evaluation in the event of an earthquake. Linear and elastic micro piles and elastoplastic soil were employed in this study. The Mohr-Coulomb criterion was employed in the failure control of the micro piles. The micro piles were subjected to the 1978 Tubas earthquake records. The numerical results were compared to experimental data. The comparison revealed good agreement between the numerical results and experimental data. The inclined micro piles were found to sufficiently enhance soil strength under seismic loading, inducing smaller displacements than vertical micro piles. Furthermore, the soil and inclined micro piles showed salient interaction.

Sep 1, 2022

By Bill Starke

The acceptance of AugerCast piles in Canada has been limited. Many engineers are apprehensive about the quality of the piles produced by this method. However, advances in the sensing instruments and computer technology can now provide satisfactory levels of quality assurance. Post construction tests such as the sonic echo method can give an indication of pile shaft integrity. Computerized monitoring of the pile installation process is an immediate and more positive method of quality assurance. The computer continuously measures and records the parameters which indicate the quality of the pile. If these parameters do not indicate a satisfactory pile, it is replaced before the concrete hardens. Computerized monitoring of the installation process is another tool available to the engineer. The data from this system analyzed with soil borings, site inspections, and possibly sonic tests can provide the engineer with enough information for pile certification.

Jan 1, 1997

By Maurizio Siepi

The realisation of most of the civil engineering works is subordinate to the execution of consolidation works, in order to improve the soil physical-mechanics characteristics. The works classifiable with the term "Soil Improvement" can be realised using several technologies, among which the Deep Mixing Method is distinguished for his remarkable flexibility and productivity characteristics. The Deep Mixing Method is a process whereby a rotary drilling machine mechanically drills a constant diameter hole while cement slurry is injected into the soil at high pressure. The process combines state of the art construction techniques merging mechanical and hydraulic mixing energies at the tool bit. The result is a soil-cement column of engineered strength, consistency and dimension. Whereby the soil cement column formation process is controlled by a computerised device, the result is a speedy installation, thorough mixing, and a high degree of control, repeatability and documentation.

Jan 1, 2002

By Shreyas Giridharan, Fursan Hamad, Sujith Gowda, Christian Moormann

"Pile installation in soil is a dynamic process which exhibits large deformation in the soil region. Experimental investigation of pile installation is both time and resource intensive. Numerical investigation can be a helpful tool for the analysis of the installation process. Furthermore, numerical analysis allows simulating various soils and loading conditions with ease. Finite Element Method (FEM) – a widely used framework for numerical simulations - fails to perform well for soil mechanics where large deformation and heavy material movement exists. In order to alleviate this shortcoming, Material Point Method (MPM), advancement to FEM has been used. In MPM, material points (particles) are used to represent the domain which carry the information and move over a fixed computational mesh where the governing equations are solved.In the present work, a variation of MPM, called CPDI (Convected Particle Domain Interpolation) is utilised which handles large deformation problems better than the classical MPM. Here, the material points are represented by a spatial domain which deforms according to the particle deformation. This eliminates stress oscillations while particles cross the grids. Implementation is validated and applied to pile installation in dry and saturated soil conditions. A 2D axisymmetric model is chosen, with penalty function method being used for evaluating contact between soil and pile. Sand is modelled via the hypoplastic constitutive description that takes into account large deformation, as well as small strain stiffness. From these simulations, various parameters like stress, void ratio and friction angle are studied.INTRODUCTIONOffshore piling is challenging in terms of testing and execution. Before the execution, predicting an efficient installation method requires study of various parameters, like soil conditions, type of loading, force requirement etc., and are the minimum parameters to be known beforehand. To obtain these parameters, testing a real scale prototype under different conditions is not feasible. Scaled model tests in lab can support in making certain decisions, but fail to replicate real behavior fully. Therefore, the need for a numerical simulation technique emerges, which can provide early predictions easily and accurately. This later can be extended to real scale tests, reducing the number of experimental investigation required.Simulation of displacement pile installation in sand involves large deformation due to penetration process, thereby making the application of FEM impossible, where large deformation causes heavy mesh distortions. Due to this, meshless methods are developed to treat large deformation in a better way. Among various meshless methods, Material Point Method (MPM) shows more applicability to geomechanical problems. This is mainly due to the ease of handling soil, structure and water in a unified manner."

Jan 1, 2017

By Kelvin Lo, Erwin Oh, Darren Newel

The use of interface elements is widespread in most numerical methods to separate the structural elements from soil elements. It allows slipping and gapping or overlapping between the two media in contact with highly distinct deformability characteristics, such as piles and retaining walls. However, many existing analytical methods still assume no pile-soil slipping before failure in axially loaded piles. This paper attempts to compare the slipping and non-slipping analytical models by introducing an interface with a virtual thickness. Results show that both have different load-displacement characteristics when comparing to the measured data. The non-slipping model would result in a stiffer load-displacement curve if the same input stiffness parameters applied to both models. Different procedures to calibration the input stiffness parameters in slipping and non-slipping models are recommended.

By Terrence M. Carroll, Chu E. Ho, Dimitrios Niarchos

"Construction of the new extension to Terminal 4 at John F Kennedy International Airport in Queens, New York involved the application of tapered piles for foundation support. Initial design based on past load testing experience had indicated that a pile depth of 65 feet was necessary to achieve a capacity of 394 tons. However, piles with a single length of 62 feet were ordered and installed, which led to marginal performance of the piles. This paper presents the technical considerations for mitigating the situation based on a systematic review of three preliminary pile load tests and dynamic capacity measurements on the shorter piles. Consideration was given to the long term gain in capacity of tapered piles due to set up in the Glacial Sand. The observational approach to the evaluation of piling performance adopted on this project resulted in salvaging many piles which failed to comply with the specified driving criteria. It was acknowledged that a more prudent course of action was for the Contractor to have ordered more appropriate pile lengths that allowed for potential variation in soil conditions across the site. The 4.6% saving in pile material did not warrant the effort that was required to mitigate the 39% of installed piles that did not meet the specified driving criterion.INTRODUCTIONAn expansion project at John F. Kennedy International Airport in Queens, New York involved the Phase 2 extension of Concourse B at Terminal 4. The site consists of 4 to 5 feet of pavement over about 10 feet of hydraulically placed sandy fill. Below this is a layer of marsh deposit, comprising of soft organic clay and peat, up to about 11 feet thick. Beneath the marsh deposits is a deep layer of glacial sand which extends to well over 100 feet below ground. Figure 1 shows the typical subsurface profile at the site. The new structures were supported on 223 steel tapered piles. The piles consisted of a straight steel pipe 18 inches in diameter and 0.375 inches thick, with a 25 feet long tapered bottom section (diameter varying from 18 inches down to 8 inches at the pile toe). The piles were first driven to the founding depth and subsequently in-filled with concrete. The concrete strength (fc) specified was 4,500 psi and the yield strength of the steel piles (fy) was 50 ksi. Initial pile design, based on earlier experience with static pile load testing for Phase 1 development at the same terminal, indicated that a pile length of 65 feet was necessary. However, piles with a single length of 62 feet were ordered and installed by the Contractor, leading to marginal performance of the piles. This paper presents the technical considerations for the adoption of alternative pile driving criteria, based on a systematic review of the preliminary static load test results for the present site and PDA measurements obtained during pile installation, in order to accommodate the capacity of the shorter piles."

Jan 1, 2017

By R. Bruce Patterson

The New Tacoma Narrows Bridge is a classic suspension bridge founded on concrete caissons. Caisson construction was complicated by the proximity of the existing bridge piers, only sixty feet away. High capacity plate anchors were used successfully to moor the new caissons in currents as strong as seven knots during construction.

Jan 1, 2004

By Alan B. Wagner

The River Tower is a proposed 27-story condominium building in the heart of downtown Milwaukee, Wisconsin (USA). The tower will be over 100 m tall, and will have a ground area measuring 15 m by 40 m. The structure will be constructed of cast-in-place reinforced concrete. Certain transfer girders and stabilizing diagonals will be constructed of post-tensioned concrete. Vertical loads will be transmitted through an arrangement of columns, bearing walls, and elevator and stair cores. A mat foundation will be used to connect and integrate these load-carrying elements. The site's geologic profile includes 8.4 m of compressible estuarine (organic) deposits. To control settlement, the mat will be pile-supported. These deposits are underlain by moderate-strength inorganic deposits that extend to bedrock at 32 m.

Jan 1, 2002

By Padmavathi V, M. Najamuddin, M. R. Madhav

Granular piles are one of the leading ground improvement techniques, adopted for the betterment of bearing capacity and reduction in settlements of the foundations and also to accelerate consolidation of the surrounding soil. In the recent past, there has been extensive research on the settlement analysis and behavior of granular piles under varied soil conditions. The application of these theoretical solutions to practical problems requires a knowledge of representative values of the deformation parameters of the ground and the granular piles. However, very little information is available on these parameters. The paper presents a new method for the estimation of the modular ratio of granular piles and modulus of deformation of the surrounding in-situ soil from the compression load tests. The load - settlement response obtained from the compression test results are used in the back analysis for estimating the modulus of deformation of the ground. The presence of granular bed, under the rigid plate for load testing, has been given due consideration in quantifying the proportion of load transferred on to the stone column. Based on these considerations a new method is developed to estimate the modulus of deformation of the ground and the modular ratio of the granular pile.

Sep 1, 2022

By S. Narasimha Rao

Significant amounts of lateral load may act on pile foundations supporting structures such as transmission line towers, tall structures, bridge abutments, offshore platforms, quay wails, harbour structures and anchorages for water front structures. There were several theoretical and experimental studies conducted on laterally loaded piles in clays to determine ultimate lateral capacity and deflections under working loads. Under a lateral load, a pile deflects in the direction of load application and the soil in front of the pile offers resistance to this movement. The ultimate lateral resistance of a pile can be estimated considering the statics of the pile for a known distribution of soil resistance with depth. In this paper, considering the contributions from both lateral shear drag and frontal passive earth pressure, a method has been proposed to estimate the ultimate lateral capacity of rigid piles in clays. The lateral shear drag has been estimated in terms of adhesion and shape factor. A few load tests were conducted on model piles subjected to lateral loading and these experimental values are used in verifying the proposed method. The reported results obtained from both model tests and field tests were used in support of the predictions made. In all the cases, there is a good agreement between the predicted and measured capacities.

Jan 1, 1996

By R. J. Yan

There was a plant equipped with a 32000t Hydraulic Press to be built, under which a box foundation of 22.5m x 15m x 14.25m (depth) with a base slab of, varying thickness was proposed. The subgrade reactions, bending moments and settlements needed to be determined by means of in-situ model test. A model of the same materials as the prototype scaled to l/10 was embedded in-situ with simulated depth in the bedrock. A lot of data obtained from 39 bench marks, 32 elongation measuring points, 30 couples of electric resistance strain gauges and 24 pressure cells attached to the model foundation enables all the quantities required to be found out. Since it was put into operation, the settlements measured has reasonably agreed with the test results and the foundation has been in good condition.

Jan 1, 2010