Search Documents

By Donald R. McMahon

This paper presents a unique case history that documents the use of a braced secant pile wall to underpin a heavily loaded footing inside of a manufacturing plant. Construction of a pit for a new manufacturing process directly next to the footing necessitated the underpinning. The footing supports an overhead crane that needed to remain operational throughout construction of the pit and therefore, settlement of the footing could not be tolerated. The base of the footing was about 7.7 feet above the base of the 17-foot deep excavation. The footing bears on a silty clay deposit that grades from a stiff consistency beneath the footing to a soft/medium consistency near the base of the pit excavation. This paper describes the design and construction of the secant pile wall and bracing to control wall deformations, ground movements and settlement of the footing. The footing was monitored for settlement throughout construction of the pit and no measurable movement was observed.

Jan 1, 2006

By Andrew Port, Ali Ghandeharioon

Nonlinear seismic deformation analyses using the finite difference program FLAC were performed for a wastewater treatment plant to estimate foundation displacement and performance of two proposed trickling filters during the 2475-year event design earthquake. The effective stress based constitutive model UBCSAND, which captures the cyclic behavior of both the “sand-like” and “clay-like” materials, was used to model the dynamic response of the soil strata. Dynamic analyses of the site indicated that in absence of ground improvement or deep foundations beneath the proposed trickling filters, those structures would undergo horizontal displacements in excess of 1 m and short-term differential settlement gradient of about 400 mm over 50 m as a result of seismic and post-seismic settlements. Three mitigation options were considered for limiting the seismic displacements and differential settlement gradients of the proposed trickling filters. These alternatives include vibro-replacement stone columns, vibro-replacement stone columns plus supplementary cutter soil mixing (CSM) configurations, and pile foundations. Various layouts for each mitigation option were considered including the lateral extent of the ground improvement, CSM walls and pile spacing. Seismic horizontal and vertical displacements of the proposed structures as well as post-earthquake consolidation settlements due to dissipation of excess pore water pressures in soil layers were assessed in all the analysis alternatives. The analyses indicate that all the alternatives considered have the potential to provide a comparable level of seismic and post-seismic performance. However, for similar performance levels, the ground improvement options need to extend well beyond the edges of the proposed structures, while the piles can be limited to just beneath the footprint of the structures. INTRODUCTION Annacis Island Wastewater Treatment Plant (AIWWTP) is owned and operated by Greater Vancouver Sewerage and Drainage District and services a population of approximately 1 million people in Vancouver, British Columbia. Wastewater is generated by residential, commercial, and industrial sectors and the treated effluent is discharged to Annieville Channel of Fraser River on the south side of Annacis Island. AIWWTP is located on a 51-hectare site and was commissioned in 1975 as a primary treatment plant, but has had two major expansions to meet the population growth needs, and to improve the treatment process efficiency through the provision of secondary treatment of the liquid stream. The current expansion includes construction of additional solids contact tanks and secondary clarifiers. Future expansions include the construction of proposed additional trickling filters. New expansion structures are required to be designed for post-seismic operation after the 2475-year event design earthquake.

Jan 1, 2018

By H. S. Radhakrishna

Foundations supporting power transmission and communications towers are subjected to both compression and uplift loads, often of a cyclic nature. Some novel foundations, combining the beneficial features of grouted and helix anchors with that of compression piles and grillages, were developed by Ontario Hydro during the construction of high voltage transmission lines in Ontario, Canada. In addition to meeting the load requirements, the foundations permit easy installation in swampy areas and also minimize impact on environmentally sensitive terrain. This paper describes the features of these composite foundations and outlines the performance criteria used for their design and installation on the basis of load test results.

Jan 1, 2010

By Takefumi Takuma, Masashi Nagano, Koji Kajino

As part of the construction of a multi-span pre-stressed concrete girder bridge for Japan’s new high speed rail line, landslide preventive piles were installed on the flank of a steep slope. The rotary pressin piling method was selected to install three parallel rows of long (up to 36m, i.e., 118ft) and large diameter (1,200mm, i.e., 47.2in) pipe piles safely into the slope as a deterrent measure. They were spaced at 2.5 Dia (3.0m, i.e., 9.8ft) on center and were staggered to allow the groundwater to migrate between the piles. Each pile had a sacrificial cutting shoe welded at its toe for speedy installation and was rotated and simultaneously pressed into soil on the slope through the stable bedrock thereunder to achieve a robust landslide prevention in a relatively short period of time.

By Edward L. Hajduk

During sonic logging quality control testing of the drilled shaft foundations for the replacement bridges crossing the Broad and Chechessee Rivers for SC 170 in Beaufort County, South Carolina, irregular signals were observed on a consistent basis near the shaft top elevations. These irregular sonic signals were attributed to access tube ?debonding?, which is the separation of the access tubing from the surrounding concrete. A total of 160 drilled shafts were installed for this project, of which 41 were evaluated using sonic logging testing. Both PVC and steel access tubes were used during the project to allow for sonic logging testing. This paper details the investigation of access tube debonding with time, discusses the solutions used to minimize access tube ?debonding?, and presents the results of the sonic logging testing for the entire project. The solution selected, installation of PVC along the pile length and steel access tubing within 40 feet from the top of shaft, allowed for reliable sonic logging to effectively evaluate the upper portions of the drilled shafts.

Jan 1, 2004

By Siavash Mahvelati, Alireza Kordjazi, Joseph Thomas Coe

Deep foundations are often constructed as end bearing members with a significant amount of their capacity derived from bedrock. Sites with highly variable bedrock conditions therefore present a unique challenge when attempting to estimate the design elevation of deep foundations. Typical subsurface characterization techniques such as drilling, standard penetration testing (SPT), and cone-penetration testing (CPT) may fail to adequately establish top-of-rock elevation in geologic settings prone to karst and/or significant amounts of residuum, saprolite, and deformed bedrock. Seismic surface wave geophysical methods have been increasingly used to map bedrock topography in such settings. However, the current standard of practice for these methods introduces resolution limitations in spatially variable subsurface conditions due to averaging effects from the analytical framework used to process the acquired data. This study explores the use of a tomographic approach with full waveform inversion (FWI) to map top-of-rock elevations at a numerically simulated site representative of highly variable bedrock topography. Comparisons are made with seismic refraction (SR) and a dispersion-based multichannel analysis of surface waves (MASW) approach as more commonly used in geophysical subsurface investigations. The results highlight that FWI provides a superior estimate of top-of-rock topography than SR and MASW at a cost of a significant increase in the required computational resources and time.

Sep 8, 2021

By Aly M. Mohammad

The Howland Hook Terminal Facility located in Staten Island, New York is one of the most active container terminals in the Northeast United States. Due to the high capacity of the facility, the Port Authority of New York and New Jersey (PANYNJ) recently acquired the adjacent 37-acre Port Ivory Facility. Expansion of this Site facilitates the additional transfer of goods for rail transport, where formerly the facility was solely highway transport. Upon completion, the facility will have the ability to transfer containers directly to a freight rail line onsite by crossing from Howland Hook Site to the Port Ivory Site via a proposed bridge over Bridge Creek. The geology of the Port Ivory Site consists of shallow glacial deposits left by the leading edge of the last advance of the Wisconsin Glacier. Glacial and marine action over the millennia and the modifications of past construction combined to form a challenging site geologically. Prior to the PANYNJ acquiring the site, the Port Ivory Facility was occupied by Proctor and Gamble for nearly 100 years. Over the course of time, the site has had a variety of structures constructed and demolished at the site. The earliest structures were often supported on shallow foundations and the foundation types used progressed over the years transitioning from low capacity timber piles to various new pile types as they became available; such as Raymond tapered piles, steel piles with concrete cores, precast piles and cast in place foundations. Currently, we are designing 4-foot diameter high capacity drilled shafts to support a new bridge over Bridge Creek to connect the two sites. Drilled shafts proved to be a very economical solution from both a design and construction point of view to carry the axial load of the bridge of approximately 400 tons per shaft. The paper will present a historical evolution of the progress of deep foundation types used at the Port Ivory Site; from low capacity timber piles to high capacity large diameter drilled shafts. The paper will also present changes and modifications of geotechnical design criteria over time that affects the type of deep foundations used. For instance, utilizing new seismic design criteria requires selecting a deep foundation system that withstands seismic loading conditions and overcomes the effects of liquefaction.

Jan 1, 2004

By Peter J. Nicholson

A new method of constructing retaining walls, in-situ, prior to excavation has been developed. This "Vertical Earth Reinforcement Technique" VERT, has been demonstrated at a full scale test wall at the National Geotechnical Experimentation Site at Texas A&M University. This 10 meter high wall, was constructed of elements of soil mixing in an array that forced composite behavior between the soil mixed elements and the in-situ soils. Inclinometers and extensometers were used to verify the performance of the wall. The construction and results of the testing are presented.

Jan 1, 1998

By B. H. Moore

Foundation and excavation problems associated with lock construction projects vary widely. Each lock requires a different foundation to respond to a unique geologic setting. The range of heights and founding materials are illustrated thru description of selected structures encountered in the United States. Examples range from 113-ft high John Day Lock on the Columbia River founded on basalt rock to the 17-ft high Lock No. 5 on the Arkansas River floated on a clay foundation. A description of the basic elements of design and construction is presented. Several case histories involving lock design and construction are assessed to aid in recognition of potential problem areas on forthcoming construction. In the past decade there have been many improvements in construction materials and techniques. The application of these new approaches to lock construction is discussed.

Jan 1, 2010

By Michael W. Neill, O&apos

Drilling slurry has become an effective aid to the construction of drilled shafts in caving and/or waterbearing soils. Historically, drilling slurry made of bentonitic clay and water was first used in the US in water well drilling as early as 1889. In coastal Texas drilled shaft contractors began using slurry, often made of on-site clay mixed with potable water, in the years following World War II, on a relatively routine basis. This type of slurry was used to "process" boreholes, in which the borehole was drilled "in the dry" until water or unstable soil was encountered, after which water and on-site clay were introduced into the borehole and mixed in place with the auger or other drilling tool. Drilling then continued under a slurry consisting of the uncontrolled mixture of clay and water until the excavation had reached a relatively impermeable and cohesive material. At this point, a steel casing was dropped into the hole and sealed into the lower stratum of impermeable geomaterial (soil or rock). The slurry inside the casing was bailed or pumped out, drilling continued to plan depth in the dry, a reinforcing cage was set in the partially cased borehole, concrete was placed and the casing was withdrawn. Some soil-slurry was undoubtedly trapped between the casing and the borehole wall, but the quality of that slurry was usually of no concern, because engineers of the period usually viewed drilled shafts as nothing more than deeply buried footings. Any unejected slurry would only serve to lower side shearing resistance, not yet considered in design, but would have no effect on end bearing. In the 1960 's the effectiveness of soil-slurry came into question because it was often ineffective in maintaining borehole stability at marginal drilling sites and because the economy of using shaft resistance, in addition to end

Jan 1, 1991

By Kyle Kershaw

Micropiles are routinely used in the United States for foundation support and stabilization of slopes. In recent years, several retaining walls have been constructed using micropiles in an A-frame type configuration to support temporary and permanent excavations at sites with limited access and limited right-of-way. Typical A-frame micropile walls consist of a row of vertical micropiles at the face of the wall and a row of battered micropiles extending into the soil or rock to be retained. The two rows are then tied together with a pile cap such that the front pile acts primarily in bending and the back pile acts primarily in tension. Because of tight right-of-way constraints at a residential site in Aspen, Colorado, it was not possible to construct the wall using conventional shoring systems or micropiles in the typical A-frame configuration. Rather, the wall was designed such that the row of battered piles was installed at the wall face and the row of vertical piles was installed adjacent to the property line behind the wall. As a result of the reverse configuration of the A-frame wall, FLAC, a two-dimensional, finite difference software program, was used to model the soil-structure interaction. The final wall design consisted of both temporary and permanent retaining wall sections with maximum heights of 26 feet. Inclinometers were installed in several piles to monitor the behavior of the retaining walls during and after excavation. This paper presents an overview of the design method, a discussion of construction techniques, and a comparison between the FLAC model and the measured behavior of the wall in the field.

Jan 1, 2007

By D. Michael Holloway

The realignment of Interstate 880 replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the proposed structures. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers and prospective contractors well beyond the limits of local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata, and quantifying the effects of installation on the long-term capacities of the piles, led CALTRANS to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1996

By Roberto Nova

The selection of the Osterberg Cell (O-Cell) technology as the standard testing method for deep foundations of the Railways Po Viaduct in Northern Italy offered a relevant number of field measures on large bored pile behaviour in alluvial soils. The assessment of pile response during such ?non standard? testing procedure was performed through the comparison with standard top load tests on companion piles as well as by numerical models of the tests including a simplified pile-soil interaction scheme. As shown in this paper, the O-Cell technology allowed a careful assessment of the non-linear pile behaviour even at quite small loading levels as those required by a posteriori proof tests on production piles. Simple numerical models proved to be very effective in the simulation and the interpretation of pile behaviour during such unconventional testing procedure.

Jan 1, 2008

By Karl A. Higgins

In 1976, Prof. G. G. Meyerhof published a famous article in the Journal of Geotechnical Engineering titled ?Bearing Capacity and Settlement of Pile Foundations?. This article presents the authors opinions on calculating pile capacities in clays and sands, group capacities and pile settlement. A portion of the article presents correlations of shaft friction and end bearing to the Standard Penetration Test (SPT) N-value. Subsurface exploration via the Standard Penetration Test is the most widely used exploration tool in the United States, so correlations of pile capacity to N-value are significant to the practice of geotechnical engineering. Meyerhof?s SPT-N correlations are relatively simple calculations compared to other pile capacity computation methods presented in the article or found in other text books (such as the a-method, b-method, Nordlund, Vesic, Meyerhof?s semi-empirical, others) and therefore are popular amongst practicing geotechnical engineers. At the time these correlations were published by Prof. Meyerhof, utilization of dynamic testing with the Pile Driving Analyzer (PDA) was not widespread in geotechnical engineering practice. Prof. Meyerhof?s correlations appear to be based upon conventional static pile load testing of instrumented piles. Dynamic pile measurements to estimate a pile?s static capacity provides certain advantages over conventional static load testing, namely the determination of unit shaft friction values at discrete intervals along the pile, and the unit end bearing support value. The author has compiled a database of driven, displacement piles tested with dynamic methods (ref. ASTM D4945, Test Method for High-Strain Dynamic Testing of Piles). The data was collected between 2002-2010 and is comprised of displacement piles driven into coastal plain sediments in the mid-Atlantic states of Virginia, Maryland and the District of Columbia. In layered soils, dynamic testing in particularly helpful as it reveals the differences in unit shaft friction for varying soil types. One hundred ninety (190) piles are included in the database, with a corresponding 1,373 discrete shaft friction and 190 end (toe) bearing measurements. The pile type typically consisted of 12 and 14 inch square, prestressed, precast concrete piles; however, a significant number of piles were steel HP 12 or 14 inch sections. The database was sorted based upon soil type, and then correlations of shaft friction and end bearing were derived in the same or similar manner as Meyerhof?s original 1976 publication. The new correlations are compared to Meyerhof?s original values.

Jan 1, 2011

Case I- Timber Pile Test- 4 pages describe the pile driving record, the pile load test and the boring log. Case II- 24 inch square prestressed concrete pile-5 pages give details about the pile driving, the boring log, the pile driving record, and the pile load test. Case III- 12 inch square prestressed concrete pile- 5 pages describe the compilation of SPT blow counts for the whole project, the pile driving record, the pile load test and the detailed boring logs. The 70 foot long pile was driven by a Vulcan 08 pile hammer. Case IV- 12 BP 53 Steel H pile- 3 pages give the pile load test, the pile driving record and the nearest boring log. The 64 foot long pile has its tip at elevation 908 ft. and the ground is at elevation 972 ft. The contractor augered to elevation 959 ft. before driving the pile with a Conmaco 08 single acting pile hammer. The hammer had an 8000 pound ram, a rated energy of 26,000 ft-1b., and a 7 1/2 inch thick asbestos cushion. Dynamic measurements were made during driving of the test pile and measured a hammer energy equal to 12,500 foot-pounds.

Jan 1, 1988

By H. Shiri

Iran's largest natural gas field is South Pars, geologically an extension of Qatar's 900-Tcf North Field. South Pars was first identified in 1988 and originally appraised at 128 Tcf in the early 1990s. This Field contains 38.6 % of the gas resources of Iran and is regarded as the largest offshore gas field in the world. Offshore geotechnical site investigations are one of the key activities of upstream fields operators to supply the EPC contractors with the required results for designing approaches of offshore complexes. In the mean time a lot of marine site investigations have been carried into execution within the phases of South Pars development. The authors are currently trying to create the fundamentals of investigating the small- and large-scale spatial variability of the South Pars Gas Field in Persian Gulf/ IRAN. Part of this investigation is the providing of an extensive data base of the offshore geotechnical properties of South Pars. Such a data base, will enable a model to be developed of the large-scale variability of these properties. In addition, this data set will provide a data whereby general trends to be established, as well as, providing relationships between geotechnical parameters and spatial parameters utilizing probabilistic and data mining methods like ANN (Artificial Neural Network) in Geotechnical Engineering.

Jan 1, 2006

By Samer R. Rabab?ah

As part of the PHX Sky TrainTM project at Phoenix Sky Harbor International Airport in Phoenix, Arizona, the existing traffic lanes at the 44th Street underpass below the Union Pacific Railroad (UPRR) Bridge will be shifted to accommodate the people mover guideway. The proposed reconfiguration and reconstruction of 44th Street required the utilization of micropiles and permeation grouting to resist the lateral forces induced by cutting into the slope below the existing bridge abutment footing. This paper discusses the evaluation of the existing bridge abutment, including analysis of the original foundation system, and design, installation and testing of a new micropile-supported retaining wall to support the cut slope below the existing bridge abutment foundation. A monitoring program was implemented during construction to evaluate the short- and long-term performance of the bridge abutment. Instrumentation included survey monitoring points, inclinometers, tiltmeters and crack gauges. A micropile load testing program was conducted to verify design assumptions concerning micropile axial and lateral loading. Numerical analyses (using PLAXIS software) were performed to predict the short- and long-term behavior of both the abutment wall and the bridge foundations. Movement data collected from the monitoring program indicate that the wall and bridge foundations are performing satisfactorily and within the general bounds of predicted movements. The results from the numerical modeling using PLAXIS software showed that the proposed solution is deemed adequate to provide the needed global stability with an acceptable factor of safety, along with acceptable deformation.

Jan 1, 2011

By Ali Bouafia

Five full-scale horizontal loading tests of piles carried out by the LCPC in France are interpreted in order to analyse P-Y load-transfer curves. The experimental piles are either bored or jacked into quite homogenous sandy soils and instrumented by strain gauges for measuring bending moments along the pile. Successive differentiation and integration of bending moment profiles have led to derive respectively lateral soil reaction and displacements then to construct the load-transfer P-Y curves. The initial horizontal lateral reaction modulus was derived from these curves and shows linear variation with depth in accordance with Gibson soils profiles. P-Y curves are validated by back-computation of the pile on the basis de these curves and the horizontal reaction modulus was compared to the recommendations frequently used in pile design practice.

Jan 1, 2002

By Mark R. Svinkin

Regulations are needed to keep construction vibrations in tolerable limits. The existing regulations were developed for low-rise residential structures, but they are incorrectly used for different super and underground structures. The existing regulations cannot prevent most of harmful vibration effects on sensitive devices, people and structures from construction and industrial vibration sources. It is important to determine the areas of application of the existing regulations and bring attention to the necessity of measurement of the structural responses for assessment of vibration effects on structures. For multi-story residential, commercial and industrial buildings, the frequency-independent safe limit of 51 mm/s (2 in./s) can be chosen for the peak particle velocity of structural, not ground, vibrations. Specifications for construction operations with dynamic sources have to consider specifics of each construction site. Preventive measures can be used to mitigate harmful vibration effects on various structures and settlements in sand and clay soils.

Jan 1, 2006

By E. W. Raabe

The paper discusses the increasing role of specialist grouting techniques to form water seals or cut-offs for deep basement construction. Raabe and Toth discuss the various grouting methods available for sealing applications and then concentrate on the use of Soilcrete Jet Grouting, a system particularly well suited to ground water control. The Soilcrete processes, suitable soil types and quality control methods are fully described, particularly with regard to the formation of cut-off walls and sealing slabs to prevent the progress of ground water or leachates. The authors have included case histories detailing their experience on designing and installing Soilcrete seals for various projects in West Germany. These include an underground rail project in Dortmund and a discharge structure for the Alz Canal at Burghausen.

Jan 1, 1989