Search Documents

By Gunhild Hennum, Tewodros Tefera, Gisle Håland, Annette Jahr

"Abstract The Gudrun field is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected to support the topside and was installed in 2011. The jacket shall be able to support 16 of 0.762 m (30 in) diameter conductors and is equipped with a drilling deck to allow for pre-drilling by a jack-up rig through the jacket. In general the soil conditions below mudline comprise of a thin top layer of very loose to dense sand overlaying several layers of sandy clay, ranging in stiffness from firm to hard. Below some 30 m depth the soil consists of layers of medium dense to dense silty sand overlaying very hard sandy clay containing thick beds of sand to 100 m depth or more below mudline. The jacket is secured to the seabed by twelve 2.438 m (96 in) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. Different design methods were used to determine the pile penetration depth. Pile drivability was evaluated using best estimate and upper bound soil parameters. The pile driving and blow count record show that the target penetration was reached as predicted. This paper discusses the different methods used to determine the pile capacity, target penetration depth and the drivability analyses made for the Gudrun jacket piles. The soil resistance during pile driving is back-calculated from the pile installation data and compared with the prediction made.IntroductionThe Gudrun platform is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected for the Gudrun platform. The general Gudrun platform jacket configuration is to a large extent dictated by the topside layout, the requirements for support points enclosing the well slots and access for the jack-up rig. The Gudrun platform jacket is a traditional 4 legged structure with a vertical side towards the jack-up rig. At the seabed the jacket is quadratic with a base dimension of 40 by 40 metres. Figure 1 shows the Gudrun jacket during load-out from the fabrication yard to the transport barge. At the site the jacket was lifted off the barge, upended and placed on the seabed by the installation vessel. The jacket is secured to the seabed by twelve 96"" (2.438 m) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. The target penetration of the piles is 47 m."

Jan 1, 2014

By Rouzbeh Afsharhasani, Moses Karakouzian, Brandon Kluzniak

"The Vegas High Roller is the centerpiece of a new development parcel adjacent to the Las Vegas Strip. At a height of 550 feet, the High Roller is currently the tallest observation wheel in the world. The design team conducted a geotechnical site investigation to characterize the alluvial soils and cemented layers encountered and to provide foundation design recommendations for the observation wheel, boarding platform, and temporary structures needed to erect the wheel structure. This paper presents a case history of the geotechnical design process, including development of a ground model and design parameters, high-strain dynamic axial load tests, and settlement monitoring during construction. Results indicated that design parameters were conservatively assumed and that the majority of the axial load was transferred to a near surface caliche layer, thereby resulting in insignificant settlement of the foundation system.IntroductionThe engineering of the Vegas High Roller is similar in concept to that of the London Eye and the Singapore Flyer. The wheel has 28 cabins, each with a capacity of 40 persons. The top point of the structure is 550 ft above ground level at the site.A geotechnical site investigation program was undertaken and subsequent analyses were performed to provide foundation recommendations for the observation wheel legs, boarding platform columns, and temporary structures directly associated with construction of the observation wheel."

Jan 1, 2017

By Arash Saeidi-Rashk-Olia, Dunja Peric

Energy piles are gaining increased popularity due to a growing demand for clean energy. To further advance the understanding of soil-structure interaction in energy piles, recently-derived analytical solutions have been implemented to investigate the impact of stratigraphy on the soil-structure interaction. This was accomplished by comparing the measured and predicted head displacements, axial strains and stresses in an energy pile embedded in the actual homogeneous and layered soil profiles, as well as into synthetic homogeneous soil profiles. The analytical solutions for homogeneous soil profile captured the smooth experimentally observed response versus depth very well. In the case of a layered soil profile, the corresponding analytical model was capable of capturing nuances in trends of axial stress and strain versus depth at the interface of different layers. The analytical predictions for the layered profile appear to be slightly less accurate than for the homogenous profile. The experimental data obtained from the layered profile appear to be a bit more scattered than those from the homogeneous profile. In the former case, the interplay of the individual soil layers with the pile occurs while maintaining the continuity of the pile stress and displacement at the interface of different layers. The response throughout each layer of the layered profile is quantitatively different than the corresponding homogeneous response. Nevertheless, qualitatively the response throughout each layer of the layered profile is similar to the response of the pile embedded in the corresponding homogeneous layer.

Sep 8, 2021

By John Wise

Significant movement to an existing slurry wall which serves as a retaining wall on 'O' Street in Southeast Washington, D.C. initiated the Department of Public Works for the District of Columbia to invite specialty contractors to propose a rehabilitation and stabilization for the failed slurry wall. Nicholson Construction Company proposed and was awarded a contract for the construction of an anchored precast lagging and soldier pile wall to be located approximately 4 feet in front of the existing structure with granular fill placed between the new and existing walls. Stabilization of the existing slurry wall also included drilling horizontal weep holes and demolishing the failed panels down to the existing ground surface. A new and improved drainage system was also constructed to increase the amount of water directed toward the existing storm sewer system running along 'O' Street. This paper provides a detailed account of these construction activities.

Jan 1, 2003

By Richard J. Finno

This paper presents an overview of methods that can be used to predict damage to buildings as a result of excavation-induced ground movements and describes an adaptive management approach for predicting, monitoring, and controlling excavation-induced ground movements. Successful updating of performance predictions depends equally on reasonable numerical simulations of performance, the type of monitoring data used as observations, and the optimization techniques used to minimize the difference between predictions and observed performance. This paper summarizes each of these factors and emphasizes their inter-dependence. Case studies are presented to illustrate the capabilities of this approach. Examples are given to show how optimized parameters based upon data obtained at early stages of excavation can be used to predict performance at latter stages, and how they can be applied to other excavations in similar geologic conditions.

Jan 1, 2010

By Brian W. Wilson

A case study is presented that describes the design and implementation of a combined blast densification and deep dynamic compaction program which was undertaken to improve the foundation soils for a proposed tailings dam raise in Ontario, Canada. Based on the results of the geotechnical investigation it was determined that the foundation of the dam would be situated on tailings of both variable thickness and density, much of which would be susceptible to liquefaction under the design earthquake for the region and type of facility. Blast densification trials were completed by the owner and the results of these made available to prospective tenderers in response to a call for a fixed price contract for the design and implementation of a densification program for approximately 800,000 m3 of foundation tailings. The variation in tailings gradation and the impacts of such on the ground improvement program are discussed, as are details of both the additional blast densification field trials completed by the contractor, and the selected blast pattern and explosive charging used for production blasting. The applicability of the various ground improvement techniques to the actual conditions encountered, and the results obtained are also discussed.

Jan 1, 2010

By Gust Van Lysebetten, Monika de Vos

The objectives of monitoring geotechnical structures can be very diverse, including optimisation of the design, quality control, long term performance assessment, and approval of innovative execution techniques. In this context, new measurement techniques, based on optical fibres, offer the possibility of accurate strain and temperature monitoring with very small sensors and limited numbers of cables. This paper briefly presents optical fibre sensing techniques and illustrates their application to geotechnical structures by means of some projects, carried out by the Belgian Building Research Institute (BBRI).

May 1, 2022

By James E. Parkes

The Silver Spring Transit Center is a new three-level transit center that will include bus loops for County, Metro and intercity buses, parking, and retail space. It replaces an existing bus station and connects to a busy metro rail station in downtown Silver Spring, Maryland. Significant site constraints in both plan and profile had to be dealt with in developing a design for support of the structure. Over 90 rock-socketed drilled shafts ranging in size from 3 to 7 foot in diameter were ultimately used to accommodate the limited space and large column loads, and to adapt to the variable rock surface at the site. Site access during design was limited due to the existing active bus station, so contract documents were adapted to include further explorations. Differences in anticipated and actual field conditions regarding the depth, quality, and variability of the rock had to be overcome in construction. Osterberg Load Cell testing during construction allowed for verification and optimization of the shaft design. Additional issues dealt with on this constrained site in an urban setting included construction staging issues, such as working around specialty contractors for tieback walls, blasting operations for rock excavation, productions issues for hard bedrock, as well as coordination issues with third parties, most notably the Washington Metro Area Transit Authority. Aspects of the foundation design and optimization, preparation of the contract documents to deal with the complicated nature of the project, and lessons learned from construction are also discussed.

Jan 1, 2011

By Filippo Maria Leoni, Alessandro Bertero, Gianluca Pianezze

"As part of the Southeast Louisiana (SELA) drainage program, designed by the U.S. Army Corps of Engineers (USACE) to reduce flood damages in the City of New Orleans and surrounding parishes through the construction of new pumping stations and better drainage canals, the SELA-22 project entailed the installation of a concrete covered canal along Jefferson Ave. and Prytania Street, in a highly urbanized portion of Uptown New Orleans, LA. The scope of the required soil improvement was to replace the soil between two parallel lines of sheet piles with a soil-cement mass to eliminate underseepage and provide structural support for the concrete culvert. The USACE selected the jet grouting (Jet Grout) technology for the construction of the bottom plug. The bottom plug is between 18 and 21.5 ft thick with a maximum depth of approximately 40 ft, for a total length of approximately one mile. The treated soil comprised soft clays and silts with occasional presence of sands. Project specifications required 100% area coverage, a 28-days unconfined compressive strength of 100 psi and hydraulic conductivity of 1x10-6 cm/s, to be verified by testing specimens from cored samples. The specialty geotechnical contractor proposed to accomplish the task utilizing their proprietary and innovative elliptical bi-fluid Jet Grout technology, and elected to perform a pre-construction bench scale laboratory mixing program to determine the most suitable grout mix features (i.e. binder type and proportions, binder content, etc.) to be applied in the subsequent field test and production stages. This paper will summarize and compare the results obtained from the different pre-construction and construction stages; interpretations of the data will be provided, along with general considerations regarding the effectiveness and significance of bench scale testing for jet grouting applications.INTRODUCTIONIn general, the effectiveness of the construction parameters in any ground improvement work depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2016

By Philip Derbyshire, Dale J. Scheffler

"Continuous Flight Auger (CFA) piling is a variation of Augered Cast-In-Place (ACIP) or augercast piling. In both cases a continuous auger with a hollow stem is used to drill a hole and a pile is formed by injection of cementitious material through the hollow stem as the auger is withdrawn. CFA differs from conventional American ACIP by the use of concrete rather than grout to form the pile, and by the type of equipment used to advance the auger into the ground and withdraw it. CFA installation uses a European style rig (i.e. fixed mast and rotary system) which can produce greater crowd and usually has a larger rotator or drill motor than the standard augercast setup. A standard augercast setup will consist of a lattice-boom crane and a set of leads to house the drill motor and auger. The auger size will range up to 24 inches (610mm). With CFA rigs larger diameter piles can be constructed, 24 to 36 in dia. (610mm to 915mm) are common and the technique has been applied with diameters up to 48-inch (1220mm). CFA makes use of sophisticated computer controlled monitoring systems, which have more recently been introduced for conventional ACIP piling. Developments in CFA have taken place over the last 25 years in Europe and particularly in the UK, but are relatively new in the USA. One application is in the construction of secant (overlapping) piled retaining walls. D.J. Scheffler Inc. recognized the potential of the CFA system following visits to the UK and has introduced its use into California for both secant piling and other applications.BACKGROUNDThe high price of real estate in many of the favored areas of California has increasingly led owners to want to build basements under their houses to increase the floor space available on a lot. Many of these areas are by the coast where the ground conditions are predominately granular and the water table is high. Conventional shoring and dewatering systems have often caused problems with adjoining properties. Clearly tangent walls are not suitable in these conditions because of leakage and loss of ground. The secant pile system, using CFA techniques, has proved very effective at overcoming the problems experienced by other methods. Other applications for CFA secant walls have included use for an emergency job on a highway following erosion caused by unusually heavy rainfall.METHODThe concept of secanting piles, whereby primary(female) piles are installed first and then secondary (male) piles are cut into the primary piles is not new. The method has been known for more than 30 years. Originally ‘Benoto’ grabbing rigs, developed in Japan, were used together with sectionalized double skinned casing and oscillators.This early method was slow, although very effective. More recently high torque rotary machines have been used. Contractors in the UK have increasingly used CFA techniques to further improve productivity of this type of piled wall. The improved capabilities of piling rigs available, as well as developments in concrete technology and instrumentation, have made this possible."

Jan 1, 2005

By RavikiranVaidya, Vishal Dhamecha

Low Strain Pile Integrity Testing has been used in India since 1990’s and several have tried to demonstrate the utility and benefits of this method. However, use of this technology was limited till 1998 as not enough data maybe was not available to justify its use and application on major infrastructure and real estate projects. The first author has done significant work in this method resulting in its use in practically all sectors of the industry that use concrete bored pile foundations as a supporting element. The paper explains various signal enhancers or modifiers involved in processing of low strain test data and its implication on the final output. It also describes how the method can lead to abuse or can provide poor interpretation if incorrectly used. The current effort is to demonstrate that data collection and evaluation becomes complex with changes in soil stratum and pile profile. The paper highlights the present testing practices and provides a guideline for classification of pile integrity into few simple categories in Indian context rather than writing complex interpretations.

Sep 1, 2022

By Mauricio Coto

Three bidirectional static load tests (BDSLT) were executed on bored concrete piles, as part of the permanent foundations for two buildings sites located at the Sabana, San Jose, Costa Rica, separated at a relatively short distance of about 1 km. Unit skin friction values obtained for both sites, principally for the “Lahar” layer show that in general, friction pile capacity from the tests is higher than anticipated per static calculations from soil borings geotechnical parameters correlations. Results from the tests were also compared with dynamic load tests (DLT) executed at other two sites in the surrounding area, and with a Finite Element (FE) Analysis that model soil-pile interaction for one of the projects. On the other side, some construction issues were detected on one of the sites, which negatively affected the end bearing capacity, but being that pile friction was higher than anticipated, the required overall pile capacity was accomplished. The BDSLTs results of these tests help to better understand the geotechnical behavior of the soil layers in the Sabana. Moreover, they also show that is possible to optimize the design and construction of other bored pile supported buildings and structures on the zone.

By T. Jason Hardell

The Victory Bridge project was contracted by the New Jersey Department of Transportation. The project included the construction of two 4000-ft precast segmental concrete bridges to replace the existing Victory Bridge that was built in the 1920's. The existing bridge was a swing span bridge that was in desperate need of replacement. The project was considered high priority due to the large maintenance costs to keep the swing span operating over the busy navigational channel. In March of 2003 construction began on the first bridge and by April of 2005 all of the segments were set for the second bridge. On September 5 of 2005 the second bridge was open to traffic. The total cost of the project was $110-million. The two new bridges required the construction of 24-eight foot and 32-six foot diameter-drilled shafts with rock sockets. All of the shafts were constructed in the tidal Raritan River working from barges. What will follow is a description of the construction techniques that were used to build these drilled shafts, the anticipated and unanticipated challenges that were encountered during the project, and the lessons learned.

Jan 1, 2005

By Liqun Liang

Various nondestructive testing (NDT) inspection methods are available to evaluate the structural integrity of cast-in-place shafts. The widely used methods include Cross Hole Sonic Logging Testing and Low Strain Testing. Due to its advantages such as low cost, easy operation, quickness and flexibility (no need to plan ahead and prepare inspection tubes or other devices), Low Strain Test is frequently specified in quality assurance programs of many countries or when doubts arise as to the integrity of the finished shafts/piles. The method is well suited for small to middle sized shafts. However it is an indirect NDT testing method and has certain limitations. Data interpretation requires proper training, experience and judgment and, therefore, inconsistent conclusions and reporting may be provided by different testers. To avoid or reduce such inconsistencies, it is best to follow a standardized data interpretation and record classification system. In this paper, a new classification method is presented with examples. A step-by-step data evaluation and interpretation procedure is proposed with examples of real cases to help understand the LST data. The paper also makes recommendations for measures to be taken when anomalies are detected in tested production piles.

Jan 1, 2011

By S. H. Miller

Biodegradable hydraulic fluids can save tens or hundreds of thousands of dollars in fines and clean up costs in the event of a hydraulic fluid leak or spill. When properly selected, applied, maintained and monitored, a biodegradable fluid will have a long useful life and will protect equipment as well as or better than conventional petroleum based hydraulic fluids.

Jan 1, 2000

By Marcel Bielefeld, Joost Bakker, Rob van Dorp

Pile load testing can be performed by a static, rapid or high strain dynamic (generally designated as dynamic) testing method. The static load test is often considered the “gold standard” of testing with the other methods merely ‘alternatives’. However, the rapid load test, as a quasi-static test, has all the positive elements of the static alternative: the direct measurement of loads and displacements. Moreover as stress wave phenomena have no influence, the interpretation of rapid load test results is more straightforward than that of dynamic testing, and also independent of the person performing the interpretation. This paper will explore the Rapid Load Testing method and illustrate the advantages and limitations through a case study in Rostock, Germany

May 1, 2022

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By Aniruddha Sengupta, Rana Chattaraj, G. R. Reddy, Raj Banerjee

"Earthquake induced liquefaction in saturated granular soils is an important phenomenon which causes severe damage to life and property. In the present study, dynamically induced liquefaction of saturated Kasai River sand is studied in 1-g shake table to assess its liquefaction potential. In the shake table, the soil was subjected to sinusoidal motions of amplitude 0.35g at a frequency of 2Hz. A numerical model using FLAC 2D (Itasca 2005) was performed to simulate the shaking table tests. Reasonably good agreement between the experimental and the numerical results has been observed. Moreover, wavelet analysis has been conducted to identify the occurrence of liquefaction in sand and to correlate the observations found from the experiments. The nonlinear curves used to represent shear strain dependency of stiffness of the Kasai River sand was obtained from cyclic tri axial tests.INTRODUCTIONThe term Liquefaction is used in conjunction with a variety of phenomena that involve soil deformations due to cyclic disturbance in saturated soil under undrained conditions. The generation of excess pore water pressure is the hallmark of all liquefaction related phenomena and the reduction in the volume or the tendency of cohesionless soil to densify during undrained loading condition as prevails during an earthquake is also well known. Use of shaking table tests to understand liquefaction of soils has been demonstrated by several researchers (Ye et al. 2013; Ha et al. 2011). Mohajeri and Towhata 2003 and Towhata et al. 2006 carried out 1-g shaking table tests on soil models prepared in laminar box to study the rate dependent behavior of liquefied soils. Ueng et al. 2010 used a biaxial laminar shear box mounted on shaking table to study the settlements in saturated clean deposits of sand and related the volumetric strain in liquefied sand to the relative density for various shaking durations and earthquake magnitudes. Maheshwari et al. 2012 reported increase in liquefaction resistance of reinforced sand through shaking table tests and concluded that the type and amount of reinforcement in the soil layer has influence on its liquefaction potential.The objective of the present study is to compare the behavior of dry and saturated Kasai River sand when subjected to seismic shaking. The Kasai River separates two growing cities, Medinipur and Kharagpur in the state of West Bengal in India. A number of road and railway bridges exist over the river connecting the two cities. The area being in Seismic Zone III, that is, a zone with moderate probability of earthquake, it is important to characterize the behavior of the Kasai River sand during a possible earthquake event especially when a number of bridges are existing over it. Small scale laboratory model tests and numerical analyses using a commercial finite difference algorithm called FLAC2D (Itasca 2005) have been utilized to study the difference in behavior of dry and liquefied Kasai River sand during dynamic loading conditions."

Jan 1, 2015

By Jie-qun Zhai, Jian Jia, Ke Yang, Xiao-lin Xie, Yu Zhang

"With cities’ development, underground space exploitation presents a need for bigger and deeper constructions now. Technical problems founded during the construction of deep foundation pit support become more and more important. The supporting system has to cut or partly cut off hydraulic connection outside and inside the foundation pit, control the ground settlement caused by dewatering and make sure safety of foundation pit and its surroundings. Some preliminary study and application of ultra-deep soil reinforcement methods have been conducted in Shanghai’s deep excavation engineering. On the basis of engineering practice of ultra-deep foundation pit in Shanghai, some field and laboratory test, this paper analyzes effects of different ultra-deep soil reinforcement methods and their influence characteristics of surrounding environment. It also summarizes these methods’ sealing effect, construction and economic efficiency and concludes their characteristicsINSTRUCTIONShanghai is formed from marine sedimentation. In Shanghai, from earth’s surface to 30~40m underground, soil is mainly consist of soft clay with 40% moisture content. There are also many thin silty-sand layers in the earth, so the soil is both soft and permeable. Under 40m, soil is mainly thick silty-sand layers and fine-sand layers with medium density and confined groundwater whose water head is about 7m high.With the rapid development of Shanghai’s municipal construction and high-rise buildings in the recently ten years, the number of underground structure including subway station, tunnel and high-rise building basement are constructed rapidly. Due to the permeability and softness of Shanghai’s soil, it is necessary to reinforce soil to make sure the safety and high construction rate of engineering project in Shanghai.Because of deeper excavation depth and bigger excavation area in Shanghai, ultra-deep soil reinforcement is used preliminarily in Shanghai. Combining with engineering practice of ultra-deep foundation pit in Shanghai and employing field and laboratory test, this paper analyzes effectiveness of different ultra-deep soil reinforcement methods and concludes these methods’ characteristics and their applicability. All this can guide further application of these methods."

Jan 1, 2015

By Robert C. Simpson, Ghada S. Ellithy

"There are several methods for estimating the axial capacity of drilled shafts installed in coarse-grained soils. Most methods estimate the ultimate capacity for side friction and tip resistance. Design capacity is then calculated by applying a resistance factor to the ultimate capacity. In reality, however, ultimate resistance may not be mobilized except after a significant displacement that is not structurally tolerated in either compression or tension modes.A full- scale load test is the best way to obtain the load settlement curve for a drilled shaft, especially in soil formations where accurate estimation of soil frictional properties from a field investigation may be difficult. This paper presents the results of a static, axial, compressive bi-directional load test, using the Osterberg method (O-cell test). The test was designed so that the shaft above the O-cell would move up and the shaft below it would move down when loaded. At the start of the test the concrete around the O-cell is fractured generally on a plane near the bottom of the cell.The test was designed to validate the design capacity of drilled shafts embedded into the Vashon recessional outwash (Qvro), which is a glacially derived sediment consisting of thick deposits of cobbly sand and gravel relatively free of silt and clay found in the Seattle, WA area. The test shaft consisted of a 2.5- feet (0.75 m) diameter drilled shaft. The test shaft was installed to a depth of about 47 feet (14.3 m) into this formation. A maximum load of 437 kips (1.95 MN) was applied during the test, in each direction. The maximum load was attained at upward and downward displacements of less than 0.1 inch (2.5 mm), respectively.Although the load test did not yield ultimate values, the results are compared to the design assumptions using methods adopted in the FHWA and AASHTO guidelines, which verified the adequacy of the design assumptions. We conclude that more emphasis is needed in the prediction of the service loads and corresponding mobilized displacement that may lead to a more cost effective design. It is also clear that more testing to higher loads could lead to more efficient designs on specific projects and generally as data is added to the local knowledge base."

Jan 1, 2015