Search Documents

By Bernardo J. Jiménez Vega, Edy L. T. Montalvan

Rammed stone columns and similar reinforcement systems are used worldwide more frequently as a cost-effective method for improvement of foundations on soft soils. The effectiveness of the treatment method is evidenced by the increase in bearing capacity and reduction of compressibility of the treated ground. In this study, two job sites with over 500 stone columns were studied. On both jobs sites, shallow soft silty soils were found and stone columns were designed to support the foundations of MSE walls, which serve as abutments for viaducts. In order to verify the soil improvement efficiency CPT tests were performed before and after the construction of stone columns, also plate load tests were performed on both job sites to verify the deformation modulus of the stone columns. From CPT data it was observed an increase up to 30% of sleeve friction and 20% of tip resistance, which demonstrated a higher deformation modulus maintaining the same strength in the soil after stone columns construction. The plate load tests yield load-deformation curves which indicated that the original assumed modulus was conservative. As a result of these findings, optimization of the settlement reduction ratios was conducted using the modified values of deformation modulus for the soil and stone column, obtaining a reduction up to 30% of stone columns for further job sites with similar soil conditions.

Sep 8, 2021

By Dario Libano, Armando Caputo, Francisco Caputo

"UHE Peixe Angical is a 452 MW hydroelectric power plant located on the Tocantins River in Tocantins, Brazil. In 1999, geologists began feasibility studies to estimate the river’s hydroelectric potential, and the decision was made to proceed with the construction of a power plant. In 2002, after extensive investigation, the studies indicated geological homogeneity at the site for the dam, except for an anomaly detected on the left margin, and construction began on the $1.2 billion project.As the work began, the complex ground conditions presented several serious difficulties. The solution was unlike any undertaken before in Brazil— a 100-m-long secant cutoff wall, with 76 1.8-m-diameter piles of up to 78 m deep. All were placed in a six-month period.In the preparation for the detailed construction plans, further studies in the area of the anomaly better defined the geology so that a treatment program could be developed. The feasibility study had detected silicified rock with high permeability in one area, and an injection curtain was designed with five injection lines. In the other area with an anomaly, further investigation revealed a permeable marble formation that was 50 m thick. Here, a specific injection program with three injection lines was developed.The injections started in February 2005 in the marble formation area. By July of that year, only the primary and secondary holes were drilled from the three lines, resulting in a space between injections of 1.50 m. By the end of July, the drilling was halted. The contractor had identified a thick area of heterogeneous material below the transition zone that was characterized by a mixture of soil, fractured rock and hard fractured rock. The anomalies were detected while drilling, and both the general contractor and the designer concluded that the phenomenon of “piping” was taking place.Constructing a positive cutoff wall became a priority."

Jan 1, 2009

By Roy Jennings

The Discovery Expedition of St. Charles, MO chose to build its two-story museum in the flood plain of the Missouri River, near the starting point of the Lewis and Clark Expedition. Should the lower level be inundated at flood stage, plans call for the replica riverboats to be moved by trailer to higher ground. The museum's design required an open span structure with heavily loaded footing or piles. Spread footings could not be used due to the compressible soil profile. The location, in a historical district, precluded dynamically driven piles. Sixty-three uncased Helical Pulldown Micropiles were driven to the bearing stratum to support the museum with minimum disturbance. There were no spoils to dispose of during construction and the piles were completed in eight working days with minimum impact to the environment and neighborhood. The maximum working load required was 84,000 pounds (374kN). Test results are given in the form of installing torque.

Jan 1, 2003

By J. J. Beresford

The primary function of a support slurry is to provide stability during excavation. Today foundation structures can be designed around the additional friction afforded by the absence of the filter cake attributable to the use of polymeric fluids as support slurries. These fluids use pseudoplastic fluid viscosity to advantage over the fragile thixotropic gel structures of bentonite. Many of today's polymeric fluids are environmentally acceptable for disposal directly to municipal sewers.

Jan 1, 1989

By Markus Schönit

Double rotary drilling combines continuous flight auger drilling with a casing for producing a cast-in-place pile. When producing a pile an outer casing and an auger (hollow auger) rotating inside the casing are driven into the ground in counter-rotation. The outer casing serves to support the surrounding soil and the inner auger excavates the drilling cuttings to the surface inside the casing. After reaching the projected drilling depth concrete is pumped through the hollow stem of the auger and outer casing and auger are extracted. After their complete extraction a reinforcement cage can be inserted in the fresh concrete. Compared to Kelly drilling the double rotary drilling method offers numerous advantages, including, for comparable diameter and length, shorter production times and higher accuracy (pile inclination and excess concrete) combined with increased occupational safety and lower noise emissions. Moreover, pile tests have proved that piles produced by double rotary drilling feature higher axial load-bearing capacities than comparable piles produced by Kelly drilling. This article offers an overview of the basic theoretical principles of double rotary drilling lists the required and currently available machinery and, finally, discusses the results and conclusions of a current jobsite.

Jan 1, 2011

By Dennis Nottingham

Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971 L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers' experiments, observations and measurements, led to an "H" pile probe design which has produced measured soil density improvements up to 250% using SPT "N60" values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern "Open Cell" bulkhead projects will be presented and discussed.

Jan 1, 2004

By Jan Pru?ka

This paper describes the sheet pile design for the Line C extension from Ládví station to the North of Prague. The first part of the paper describes the geological conditions and structural configuration of the project. Typical cross sections, the description of the construction stages, and monitoring are discussed. The second part of the paper focuses on the sheeting design method. It describes the method of dependent pressures, that is, how the pressures acting upon a structure depend on the deformation. The design process and verification methodology are described in detail with comparison of the results with in-situ monitoring.

Jan 1, 2011

By D. R. Dance

The Resonant, or as it has more commonly come to be known the 'Sonic' Pile Driver, dates back to the early 1960's, when prototypes were produced by Charlie Guild, of Providence, Rhode Island, and A1 Bodine of Los Angeles, California, these were later to be developed into the unit known as the BRD 1000. Based on this initial work, the Shell Oil Companies of Sonico and The Resonant Pile Corporation, produced and operated 30 of these BRD 1000 machines, which were used throughout the U.S.A. and Canada on a wide range of foundation projects. Subsequent to this, Raymond International and G K N, of England, operated units on programs; the G K N units being of slightly modified configuration. In 1973 Hawker Siddeley Canada Ltd., acquired the license for the Pile Driver and related systems with the intent of promoting the use of the machines to install support pilings on the Alyaska Pipeline Project, but this did not materialize due to problems with the oscillator. After radical redesign and field testing of the oscillator system the unit was employed on a number of test projects principally in Northern Canada and Alaska.

Jan 1, 1987

By Nagarajkumar BV

Pavai-and TeampT JV started working on the project T49A, Sumbar J & K State as part of slope and earth stabilization for ongoing Banihal - Katra Railway Connection Project. This project has several tunnels and bridges with slopes that are protected with various types of protection system such rock bolting, rock anchors, and micro piles. For the main two bridges Bring number 2 and 3 at T49 A location Pavai - TeampT JV has to design and execute the circular group of micro piles (Fig.1) for deep excavation of earth for the purpose of construction of well foundations (CAISSON FOUNDATIONS) for both bridge 2 and 3 piers. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with composite rock bolt applications and permanent rock anchors for slope stabilization works in this project.

Nov 1, 2022

By R. Lee Wooten, David R. Shields, Darren D. Clark

"Borehole permeability tests that measure flow or head changes in boreholes located within seepage barrier walls are commonly used to estimate the in situ permeabilities of those walls for quality control and assurance. The current state of practice for estimating permeabilities from these barrier wall borehole tests is to use equations published by M. J. Hvorslev in 1951. Hvorslev’s borehole test equations model an infinite stratum of uniform permeability, which is not the actual condition for a test performed in a low permeability barrier wall located within a high permeability stratum. We examine and develop alternative equations based on line source analytical models, which more closely match barrier wall test conditions. We describe how these alternate equations can be used to estimate barrier wall permeabilities from borehole tests and compare the results to those obtained from the Hvorslev models. We also provide recommendations that consider differing upstream and downstream water levels.Barrier Wall Permeability Tests - State Of PracticeThe installation of seepage barrier walls has become more common in a variety of applications ranging from dams and levees to contaminated sites requiring retardation of groundwater flow. The types of seepage barrier walls and installation methods include soil-bentonite, soil-cement-bentonite, concrete, self-hardening slurry, geomembranes, and sheet piles, installed with various soil mixing, slurry-supported trench, and driving methods.Owners and contractors have used a variety of methods to evaluate the permeability of these seepage barriers. The following table lists commonly used quality control/assurance tests for evaluating the permeability of a seepage barrier."

Jan 1, 2016

By Nuno Cruz, Saúl Rodríguez

"When executing offshore bored piles there are several specific factors and problems to consider in order to guarantee excavation stability. One of the methods employed to carry out this type of work consists in setting up a floating work platform, typically a barge, and implementing a soil stabilization system that combines a partial steel guiding casing with third generation polymeric drilling fluids. The main aspects to take into consideration when performing offshore pile boring works are soil stabilization, project design, work methodology and operational aspects. An example of a work methodology problem arises before any pile boring work takes place as the steel guiding casing contains water, sometimes salt water. What to do with this water in order to replace it by an adequate polymer fluid will determine the stabilization capacity as soon as the shaft advances below the protection of the casing. Another example of operational problem may derive from barge movements while executing boring activities. This study is the result of extensive field data collection and concrete logging analysis from marine projects using polymers in different continents. The bored pile stability target was set ranging between 2% to 15% of concrete overbreak. Values above 15% or below 2% mean that there is a stability problem. Then the off-target pile’s data is collected, analyzed and classified under categories. Thus, a direct correlation is established between the problem category and the final results. Modifying steps in the pre-established construction methods or operational variables guarantees target results without the need to replace the approved construction methods. As a general conclusion, the worldwide experience in large diameter marine works, allows to provide truthful information and solutions for these problems. In knowing how to follow a logical sequence of work and applying adequate work methodology will be the key for success.GENERALBackgroundTo carry out the drilling process of offshore bored piles there are two main options to take into consideration: drilling the pile by using full guiding casing until final depth; or using a combined system of partial steel guiding casing and support drilling fluids.The knowledge and situations described in this paper come from the experience acquired in different projects where the second method was employed. This construction method consists in installing a steel guiding casing by vibration and thus covering the water table and further stabilizing the soil below it with polymeric fluids until reaching the pile’s final depth. The Fig. 1 schematic shows an example of this method where H corresponds to the length of the steel guiding casing whereas the remainder of the shaft’s length is stabilized by polymer fluid. The entire bored length is full of slurry up to top of casing.In most cases this kind of civil works results from the need to build a bridge or executing port structures in places where the creation of temporary artificial peninsulas with fill material is impracticable or not allowed. Hence the need to use floating work platforms, commonly referred to as barges."

Jan 1, 2017

By Ground Improvement Committee

The evaluation of earthquake-induced liquefaction has become a routine part of geotechnical engineering design. For a given project, if an analysis identifies a potential for liquefaction and the consequences of liquefaction are deemed unacceptable, then some form of hazard mitigation is required. Mitigation efforts may consist of removing the liquefiable soils, bypassing the liquefiable soils with deep foundations, structurally accommodating the deformations or strength loss caused by liquefaction, or preventing the onset of liquefaction through ground improvement. The fundamental ground improvement mechanisms for liquefaction mitigation include densification, drainage, and reinforcement. When evaluating, recommending and specifying various ground improvement methods for liquefaction mitigation, practitioners should understand the fundamental mechanics involved and applicability and limitations of the various methods. The DFI Ground Improvement Committee offers a review of the fundamental mechanics and commentary on the applicability and limitations of each method to provide clarity and guidance on the issues related to ground improvement for liquefaction mitigation.

Aug 1, 2013

By Paola Campana, Maurizio Lenzi

"In the paper a non linear model for the analysis of the pile response to the axial loads is presented. The study aims to find a general analytical solution concerning the pile-soil interaction modeled by means of the method of the load transfer curves. It makes use of a criterion based on the plastic and on the hardening work locally done by the shear stresses and due to the current elastic shortening of the shaft. Then a specific solution, denoted fractal model, is found applying recurrent relations that link the shaft shear stresses and the tip normal stresses to the pile settlements. These relations are based on that one proposed by Kondner in modeling the soil samples response in the triaxial tests and then used by Chin in the inverse slope method in estimating the pile capacity by the load test results. The comparison between the model predictions and the load tests measures validate the fractal model.INTRODUCTIONThe behavior of the axially loaded piles is known to be characterized by a highly non linear trend caused by the onset of plastic and irreversible deformations in the soil starting just from the first load levels. With the purpose to reach a deeper understanding of the pile-soil interaction, the influence of the soil inelastic properties on the distribution of the axial loads and of the vertical displacements is investigated. The research starts analyzing the behavior of an infinitesimal length of a pile embedded in a non linear homogeneous soil. That initial study leads to a criterion based on the plastic and on the hardening work locally done by the shear stresses and that allows to find the axial loads as a function of the elastic shortenings of the shaft. The relation that links the pile axial load to the elastic strain of the pile material is then used. That allows to find the vertical displacements and the axial loads as function of the depth in a parametric form in which the tip settlement acts as an independent parameter. The method of the load transfer curves is used and the effects of the pile technology are included in the soil constitutive relations. The analysis is then extended to the non-homogenous soils in a very effective way. The solution is applied taking as constitutive relations of the pile-soil interface the one proposed by Kondner to analyze the soil triaxial tests and by Chin to interpolate the pile response measured in the load tests."

Jan 1, 2017

By Cau T. Bui

Thanks to Doi-moi (renovation) policy, many great bridges were constructed in Vietnam to meet demands of her booming economy in the recent decade and deep foundation structures were the only alternatives for the foundations of these great bridges. The deep foundation structures were constructed by modern technologies and almost of all these deep foundation structures were designed by foreign companies and carried out by Vietnamese workers and engineers under supervision of foreign experts. Beside successes, there were several failure cases in which the collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation killing 54 workers and seriously injuring 80 other workers was the most serious. This paper introduces construction techniques of the deep foundation structures applied to building of great bridges in Vietnam recently. It will especially focus on two failure cases: 1) collapse of temporary scaffolding system of Can-tho Cable ? Stayed Bridge due to settlement of its pile foundation and 2) failure of drilled shaft foundation of Thanh-tri bridge due to poor construction technique and management. These two failure cases were greatly concerned by both bridge specialists and the public. Reasons of and lessons from these two failure cases will be carefully discussed. From the two failure cases, this paper will draw some lessons that should be important issues to be seriously paid attention when designing and constructing deep foundations in Vietnam.

Jan 1, 2008

By Paul J. Sabatini

Between 2008 and 2009, more than 6,000, 23-m long deep mixing method (DMM) elements were constructed to support 124 concrete mats comprising the foundations for the process trains for an LNG facility. The Owner requested first-of-its-kind analyses and assessments to confirm the quality and reliability of the DMM foundation. This paper provides information on these assessments and the procedures used to ultimately conclude that a fit-for-purpose foundation system was constructed. During early phases of construction, several DMM test cores revealed nodules of unmixed clay in upper core samples. A comprehensive review of available DMM core information was undertaken. It was concluded that the amount of coring being conducted as part of the contractor?s QA/QC program should be increased to achieve a foundation system with the required level of reliability. Three-dimensional finite element analyses were completed considering various distributions of defects in the DMM elements and the effects of potential downdrag on DMM elements. Calculated mat settlements and mat stresses were compared to cases without defects in the DMM elements. Various distributions of loaded and unloaded mat areas and number and position (both in the subsurface and laterally) of defects were considered. Four (of the 124) mats were identified as potentially ?at-risk?. The settlement performance of these mats is currently being monitored and, to date, performance has been acceptable.

By Mohammed Sakr

A Two-Section Helical Pile (TSHP) is a steel pipe with two shaft sections of different diameters and with one or more helix plates near the bottom of each shaft section. TSHPs are used regularly in western Canada as foundation pockets for single and double circuit distribution power line poles. The results of a comprehensive lateral pile load test program and the field monitoring of TSHPs installed in organic soil (muskeg) over soft clay are presented in this paper. A total of nine full scale lateral load tests were carried out, including seven tests using TSHPs with different diameters and embedment depths, and two tests using one-section helical piles. The prime objective of the study was to evaluate the lateral resistance of TSHPs installed into very soft organic soil (muskeg) overlying soft clay soils, to compare their lateral resistance relative to one-section helical piles and to compare the measured and the estimated lateral resistances using p-y curves. In order to provide sufficient soil data for analysis, the subsurface soil stratification was evaluated using two different techniques including; Cone Penetration Tests (CPT) and Portable Soil Probe Tests (PSPT). The two testing techniques were also compared and evaluated. This paper summarizes subsurface soil conditions, pile configuration, helical pile installation procedure, testing setup and results.

Jan 1, 2009

By Shoji Higashi, Nobuhiro Honda, Takeo Asanuma, Tatsuo Nagatsu, Masaki Kitazume, Sachihiko Tokunaga, Shigeru Kubo, Hidenori Takahashi, Tsuneyasu Onishi, Yoshiyuki Morikawa

"Various kinds of civil engineering structures and facilities were seriously damaged in the earthquake in Tohoku and Kanto regions of Japan on 11 March 2011 due to the greatness of its magnitude. In contrast, many structures resisted the large seismic force having been reinforced by the CDM (Cement Deep Mixing) method, which is often used for increasing the bearing capacity of ground and improving seismic performance. This paper summarizes the field survey undertaken to investigate damage to structures and facilities reinforced by the CDM method. Several prefectures and metropolitan areas were selected for the survey, based on the occurrence of strong seismic motions. A total of 847 structures and facilities were studied, in the survey using a questionnaire, which mainly inquired about the appearance of structures and facilities. Of the respondents to the questionnaire, 789 replied that there were no seriously damaged structures. The paper presents the damaged and non-damaged sites of CDM-technique sites and non-CDM-techniques sites. It can be concluded from the field survey that the CDM Method demonstrates high efficacy and durability against a strong seismic motions.INTRODUCTIONDuring the afternoon of 11 March, 2011, a huge magnitude-9.0 Mw (Category 9.0 on the Richter scale) earthquake occurred about 25 kilometers below the Pacific Ocean’s surface off the coast of Tohoku. This massive earthquake, now called the 2011 Off the Pacific Coast of Tohoku Earthquake was the largest earthquake ever observed in Japan. The seismic intensity of this earthquake was measured 7, the maximum on the Japanese intensity scale, as observed 7 in northern Miyagi Prefecture. The earthquake caused severe damage over a wide area from Tohoku to Kanto, and triggered large tsunamis that struck the Pacific coast of Hokkaido, Tohoku, and Kanto. The number of missing and fatalities caused by this earthquake exceeded 18,000 persons, making this an unparalleled earthquake disaster with a cost-in-life toll not experienced by Japan in recent years. Because of the scale of its seismic motions, the earthquake damaged facilities and structures of many kinds. In the years prior to this earthquake, the CDM method was used extensively to increase the bearing capacity of the ground as an anti-seismic countermeasure and to prevent liquefaction. Immediately after the earthquake, the CDM Association visually surveyed the state of damage to about 800 facilities in the Tohoku and Kanto regions where a seismic intensity of 5 or higher was observed. This report summarizes the survey of damage to facilities and structures constructed applying the CDM method in order to confirm the durability and performance of the method against seismic motions."

Jan 1, 2015

By Satyajit Vaidya, Rudolph Frizzi, Luis Berroteran

This paper presents design and construction challenges associated with a high-capacity rock-socketed drilled pile foundation system for a 60-story building recently constructed in an urban environment. The site is in very close proximity to surrounding 1-to-6-story buildings and a commuter rail subway tunnel structure. High compression, uplift, and lateral loads imposed by the tall, slender tower constructed over a relatively small site footprint posed a significant design challenge due to the close proximity of the subway tunnel and other structures. Construction challenges included those associated with advancing the drilled pile casings through overburden materials using internal flush method mandated by the Transit Agency, advancing the casings through very dense glacial till materials encountered above top of rock, and drilling rock sockets in variable rock conditions. This paper provides a brief overview of the site and subsurface conditions, and discusses the resulting design and construction challenges for the drilled pile foundation system and how they were addressed. SITE AND SUBSURFACE CONDITIONS The 8,350-square-foot site is located in a busy neighborhood in downtown New York City (NYC). Buildings neighboring the site are supported on shallow foundations, and their basements extend about 15 feet below the sidewalk level. A NYC-Landmarked building is located within a NYC Department of Buildings (DOB)-designated 90-foot influence limit from the Project site. NYC Transit Authority (NYCTA) subway tunnel and station structures are located in close proximity to the Project site. The subway tunnel structure extends about 50 to 55 feet below the sidewalk level. Although the upper portion of the tunnel structure is about 13.5 feet away from the site property line, the lower portion is only about 1 foot away from the property line. A site location plan is presented as Fig. 1. Geotechnical borings revealed subsurface conditions generally consisting of successive strata of surficial fill, sandy and silty soils, and glacial till (predominantly consisting of cobbles and boulders) overlying mica schist bedrock. A generalized subsurface profile is presented in Fig. 2. The surficial fill stratum was about 10 to 23 feet thick, and generally consisted of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick. The underlying sandy and silty soil stratum was about 60 to 79 feet thick and generally consisted of loose to medium dense inter-bedded layers of fine to coarse sand, silty fine sand, and silt. The underlying glacial till stratum was about 26 to 70 feet thick and generally consisted of cobbles and boulders embedded in a very dense soil matrix. Top of bedrock was encountered in the borings about 110 to 150 feet below sidewalk level. Groundwater level was measured at about 30 feet below sidewalk level.

Jan 1, 2018

By Lucian L. Bogdan

"SummaryActive loaded strand anchors are often used for slope stabilization, retaining walls or tiedown anchors. Normally, strands are tensioned against the structure and wedges are locked inside the anchorages at a certain lock-off load. During the life of the structure, anchors can receive additional loading during a surcharge, seismic event or other activity on the structure.In order to have a reliable ground anchor system, the strand must not slip through the anchorage wedges during its service life. Strand slippage has been reported during lock-off, when dirty wedge plates and wedges have been used. Low lock-off loads are believed to contribute to strand slippage too. Since the initial lock-off load for a ground anchor is usually lower than the lock-load for an equivalent capacity tendon in other types of post-tensioning construction, there is a concern that strand slippage may occur if the load on the anchor increases above the initial lock-off load.Corrosion protection grout, placed after the anchor is locked off, fills the pocket and surrounds the strand and wedges. Some anchor installers believe that the grout will prevent the anchorage from developing additional capacity if the load increases above the initial lock-off load.The load-carrying capacity of an anchorage depends on several factors. Most important are: initial applied load, anchorage geometry, friction between wedge-anchorage-strand and condition of the contact surfaces.The ADSC Anchored Earth Retention Committee considers that the industry should know how wedges behave once the permanent strand anchors are stressed and grouted inside the transition pipe, between wedges and inside the grout cap."

Jan 1, 2005

By Nick Hytiris, Mohammed Al Maadheedi, Slobodan B. Mickovski

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.