Search Documents

By M. D. Khattar

The paper describes the salient construction features of the Pile foundation work for the Railway viaducts in Algeria. Six viaducts were constructed for execution of the Railway line between Aintemouchent and Benisaf in Algeria. The work was executed by the Indian Railway Construction Company Limited of India (IRCON) for the Algerian National Railways (S.N.T.F.). These six viaducts had multiple spans of 36M resting on hollow piers of heights upto 69M. Most of the piers were founded on piles of 1 and 1.2M dia bored piles going upto 22M deep through cal­careous rocks and were designed for Railway loading in seismically active area. The work involved 356 piles & constituted a very important aspect of the whole work. The concrete in the piles was made with sulphate resistant cement and the integrity of the concrete was tested with Sonic method so as to ensure the quality. The piles were driven with the help of a hydraulic oscillator and the concrete was laid with a tremie pipe. Problems as encountered during execution have been explained.

Jan 1, 1989

By John W. M. Lambert

This paper describes the execution and the results of a new method to seal off leaks in water retaining constructions. The new method, called BioSealing is based on activating the bacteries, present in soil and groundwater. The method was tested under field conditions in 2004 and applied at the HSL aqueduct of the 'Ringvaart Haarlemmermeer' in 2005.

Jan 1, 2006

By Tanaya Deb, Sujit Kumar Pal

"Experimental investigations are carried out on failure pattern around 2D models of belled anchor piles in dry sand bed of density 15.60 kN/m3 under uplift. The models are having thickness ratio (Ts/Tb) = 0.28, 0.32, 0.38 and 0.46 and total 12 numbers tests are performed on models possessing 45° bell angle and shaft thickness 26 mm. The foundation bed is prepared with alternate dyed and non-dyed sand layers and continued upto reaching embedment ratio of 3, 4 and 5 for each width ratio. The failure points are presented with respect to meridian section of anchor in X-Y coordinate system and the equations formed are of polynomial of degree 3; and R2 values are near about 1. The developed wedge is implemented as three-dimensional axisymmetrical failure surface around similar 3D models. In the horizontal slice method vertical limit equilibrium is used for calculating weight of wedge and mobilized shear (as per Chattopadhyay and Pise, 1986) on the slip surface of each element. The summation of all elementary forces demonstrates gross uplift capacity. The initial and final failure angles are detected and parametric study is conducted on failure pattern as well as predicted net ultimate uplift capacity. Almost all the analytical data are within ± 10% variations with respect to the experimental results of uplift capacity which shows better correlations. INTRODUCTION Belled or enlarged base anchor piles are attractive and economic alternative to the geotechnical engineers for compressive load bearing capacity as well as tension anchorage. These types of anchors may be useful for foundations erected below ground water table. In light weight structures like radar tower, television tower, power pole and outdoor sign pools imbalance horizontal forces due to wind loads, are more than of those self-weight of those structures. Due to chronic tensile loads most possibly from wind loads and associated imbalanced cable tension, the legs of power transmission tower should be properly designed to be safe against resultant pull-out forces. In belled anchor pile, uplift is influenced by embedment ratio, diameter ratio; so, contributions of these parameters on failure surface influence uplift capacity. Balla (1961) first introduced non-linear failure surface in the pattern of circular arc based on Kotter’s equation (1903) and soil friction was assumed to act on slip surface. The predictive mathematical models established by Matsuo (1967), Rao and Kumar (1987), Chattopadhyay and Pise (1986), Saeedy (1987) and Ghaly and Hanna (1994); it was reported that net ultimate uplift capacity was combination of bulk weight of failure wedge and shear resistance along slip surface acting in opposite direction of wedge movement. From the literatures available till date, it reveals that the contribution of mobilised shear and weight of breakout wedge separately, demanding for more clarification depending on the on parameters like embedment ratio, diameter ratio."

Jan 1, 2015

By Steve Davidow, Scott Tunison

As the demand for electric power grows and generation facilities are constructed in more remote areas, the industry faces an increasing number of foundation construction challenges. The importance of quality geotechnical information prior to construction is accentuated by the linear nature of the projects and the potential for drastic changes from one end to the other, but is often difficult or unfeasible to obtain. Alignments are crossing remote, rugged and/or environmentally protected terrain, and completing a comprehensive geotechnical program is made challenging from an access or economic standpoint, or both. In these situations, the industry needs a flexible foundation alternative. This paper will present micropiles as that alternative and demonstrate how the implementation of micropile foundations mitigated these challenges on the Koolau-Wailupe 46 kV Circuits in Oahu, Hawaii, which involved rugged, steep slopes and helicopter construction methods. It will detail the selection of micropiles over other foundation options, micropile and steel pile cap design methodologies, foundation construction, and quality control. Special attention will be given to the unique geology in the area, and why precise identification of saprolite and basalt layers was integral to the successful performance of the foundations. The intention is to communicate the benefits of a flexible solution based on continuous collaboration between design and construction.

By Dardis J. T. II, P. G. Reinhall

"Impact pile driving of steel piles in marine environments produces extremely high sound levels in the water. It has been shown that current pile driving noise attenuation techniques provide limited noise reduction because significant noise is transmitted through the sediment into the water. To solve this problem, we have developed a double walled pile to decrease the total noise transmitted into the water.The double walled pile consists of two concentric tubes connected by a special driving shoe, allowing for an air gap between the two tubes. The double walled pile is driven into the sediment using traditional equipment by striking the inner tube only. The air gap between the inner and outer tube prevents the radial deformation wave produced by the pile hammer from interacting with the water and the sediment. In one embodiment of the double pile design the inner tube can be removed and repeatedly reused.In this paper we report on the results from a recent full scale field test in Puget Sound, Washington. The use of these double walled piles reduces the peak sound pressure over 20 dB relative to single walled piles. We also show that only a 3 to 6 dB reduction is obtained when a bubble curtain is used on a single walled pile.INTRODUCTIONImpact pile driving of steel piles in marine environments produces extremely high sound levels in the water. It has been shown that current noise attenuation techniques provide limited noise reduction because the noise from pile driving is transmitted through the sediment into the water. In [1,2] we showed, using modeling and field data, that the primary source of underwater sound from an impact driven pile originates from radial expansion of the pile as the compression wave propagates down the pile after each strike. The radial expansion is coupled to the compression wave through the Poisson’s ratio of steel. As discussed in [1], the supersonic radial expansion wave (with respect to the water) produces an acoustic field in the shape of an axisymmetric cone, or Mach cone. We showed in [3] that the ability of any sound shield that surrounds the pile in the water only (such as a bubble curtain or a surrounding double wall engagement) to attenuate the sound in the water is limited by the fact that an upward moving sound Mach wave is produced in the sediment and is transmitted into the water. To improve the performance of bubble curtains and other noise shields in the water, it is necessary to attenuate the noise emanating from the sediment into the water. Figure 1 illustrates how sound from the seabed leaks out from the sediment, limiting the effect of the surrounding bubble curtain."

Jan 1, 2017

By Ali S. Fayad

"In June 2014, Orange County Flood Control District (OCFCD) completed construction improvements of the East Garden Grove-Wintersburg Channel for a price of $42 million. Instead of the pre-existing traditional trapezoidal levee, the channel was improved with a vertical compact levee. Dubbed Soil-Mix-Sandwich (SMS), this geo-structural and environmental solution for coastal channel improvements, underlain by liquefiable soil strata, was both a design and construction innovation. It employed Deep Soil Cement Mixing (DSCM) within the confines of a hydraulically-pressed (Giken Method) sheet pile duo. SMS was unique because it incorporated both subterranean and supra-dredge-line soil mixing within a very narrow workspace. Its DSCM pattern aimed at optimum densification of the workspace and was confirmed during the construction process. It availed the DSCM sub-contractor (Hayward Baker Inc.) the opportunity to demonstrate the fitness of their huge wet-mixing machinery within a very confined access-area and introduced approximately 70,000 cubic yards of DSCM within a limited 15 foot workspace width that stretched for a mile. The sheet pile duo created a construction-enclosure that became a stay-in-place load resisting system. PROJECT CHRONOLOGY AND LOCATIONAn Orange County Flood Control District (OCFCD) project-report was commissioned to study the East Garden Grove Wintersburg channel (OCFCD facility # C05). The report examined the hydraulic conveyance of the C05 channel and was concluded in 1994 by Williamson & Schmidt. The project-report did not encompass extensive geologic studies; but it provided several alternatives for channel improvement. It recommended a single row of sheet piles as the preferred alternative for the downstream reach.The most downstream reach of the C05 channel is located in an environmentally sensitive area, in City of Huntington Beach, California, USA. Its site includes seismic chasms that surface within the C05-footprint (the Newport- Inglewood tectonic fault). Extensive deposits of liquefiable soil exist beneath the channel. Furthermore, tidal-influence prevails against the channel levee. Implementation of a successful design for channel improvement emerged after several traditional concepts were deemed unacceptable by geotechnical consultants. OC Public Works (on behalf of OCFCD) was in need of a design and construction technique that mitigated many associated risks. From these circumstances, Soil-Mix-Sandwich was born and was referred to in the rest of this discussion as SMS. OC Public Works required the SMS design concept to undergo verification by independent geotechnical consultants. SMS chronology from conception to construction can be summarized as follows:"

Jan 1, 2015

By Brett K. Mainer

In the summer and fall of 2007, Drill Tech Drilling and Shoring, Inc. designed and built three 24-foot inside diameter shafts in Northern California using soil mix panels for support. The soil mixing was performed using the Bauer Cutter Soil Mix (CSM) method, by which rectangular soil mix panels up to 71 feet deep were arranged in an overlapping manner to form a 24-foot inside diameter circle. The shafts were then excavated to depths up to 51 feet. One of the shafts was a test shaft and used only the soil mix panels for support. The other two shafts were located immediately adjacent to the Mokelumne River and were used as access pits for a microtunnel drive under the river. These two shafts had wide flange beams embedded in the panels and were supported with several levels of ring steel placed during excavation. This project was the first use of the Bauer CSM method in the United States. The CSM method has been used extensively in Europe and Asia, but never for this application and never with this high a loading criteria due to water head and microtunnel reaction forces. Soil conditions at the river crossing shafts consisted of sands, gravels, and cobbles over top of sandstone and conglomerate bedrock ranging in strength up to 5,000 psi. Groundwater was within several feet of the surface. The shafts were successfully completed between October 2007 and January 2008, and the microtunnel was successfully completed in February 2008. This paper provides discussion regarding selection of the shoring type, structural design, the soil mixing method, and the mix designs. Shaft construction, shaft performance, and the capabilities of the CSM equipment are presented.

Jan 1, 2008

By Trevor I. Addenbrooke

Stress reducing piles were used for the first time at the Queen Elizabeth II Conference Centre near the Palace of Westminster in London, UK. The inclusion of these piles directly beneath heavily loaded columns was to reduce the high anticipated bending stress in the foundation raft, and to eliminate local yield of the London Clay beneath the column locations. Load cells were placed in one of the stress reducing piles during construction. The data showed that the pile carried about 30% of the column load. This can be contrasted with conventional piled raft design where the pile carries upwards of 80% of the column load. The build up of load on the pile and pile displacement have been accurately reproduced using coupled finite element analysis. These numerical results demonstrate the value of geometrically simple axially symmetric analyses for modelling a pile-enhanced raft. On site, excavation preceded construction of the raft and subsequent pile loading. Failure to model this construction sequence caused the shear strength to mobilize at the base of the pile first, during loading, whereas following the construction sequence caused the shear strength to mobilize at the top of the pile first.

Jan 1, 2002

By Chris L. Powell, Russell J. Denny.

"The remotely located Cockatoo Island iron ore mine off the Kimberly coast in Western Australia, which has been in operation since 1951, was recently expanded up to 50m below sea-level using staged construction of a rock-filled seawall around the open cut mining operation. The most recent stage of the seawall expansion required a seepage reducing cut-off barrier to be installed through the seawall into underlying seabed sediments. A line of grout holes at 1m centres was proposed to form the seepage barrier, with grouting extending 17m below the top of the seawall. Top hammer drilling techniques were used to penetrate the 12m deep rockfill to seabed level, and permeation grouting carried out within the rockfill to fill voids and stabilise material around grout holes. The local 10m tides meant that tidal washout of fines and grout would be a major risk, and so a combination of cementitious and chemical grout was used to create rapid gel times. Following permeation grouting, holes were re-opened to allow jet grouting to hydraulically mix and grout permeable seabed sediments below the seawall. Using the duplex jet grout system in a single pass to 17m below platform level, the jet grouting was extended upwards into the seawall fill itself to overlap with the earlier permeation grouting. Finally a soil/cement mixed capping trench was installed using slurry trenching techniques with soil/cement/bentonite mixed backfill in order to complete the grout treatment. The approach taken allowed considerable onsite flexibility in technique. An automated slurry batching plant allowed adjustment of mixes to suit the varying subsurface conditions which were encountered during the works.IntroductionLate in 2013 Wagstaff Piling was engaged to install a seepage barrier through a rockfilled seawall built to allow expansion of sub-sea iron ore mining operations on Cockatoo Island off the remote Kimberley coast in the North West of Western Australia. Earlier stages of seawall construction had used a variety of different construction techniques with varied success, and the history of sub-sea mining on the island had been plagued with failures, including failures in the slope of the seawall itself, hanging wall failure underneath and inside the seawall, and footwall failures as the ore was mined leaving the rock face inclined at 55 degrees, parallel to the bedding. The current expansion, known as the Stage 4 expansion, was more tightly constrained by the pit geometry and available materials than previous seawall expansion stages that adopted clay core and sheet pile seepage barrier solutions. In Stage 4, an innovative grout curtain seepage barrier solution was selected to ultimately provide the necessary cut-off to allow access to high grade ore, while protecting the mine from inundation by the sea."

Jan 1, 2016

By P. V. Chandramohan

"The paper deals with the arrangement of structural members for a retaining structure used as a berth in the port of Krishnapatnam. The height of retention is 24.3m. A T-shaped diaphragm wall acts as the retaining surface. A relieving platform has been provided at the top to ease lateral earth pressure on the wall. The diaphragm wall is tied back to a combination of vertical and raker pile. Later, this arrangement was altered to replace the relieving platform with just lowering of ground level below the berth. The tie back was changed to a classical A-frame anchorage. At certain reaches, installation of piles pointing towards the rear was obstructed by a conveyor structure. The anchorage was then changed to include a vertical pile and a pile that points towards the front of the berth. Change in position of inclined pile alters the force in the pile from compression to tension.GeneralPort is a major link in the multimodal transport chain. Berth is the heart of the Port infrastructure. It is here the ocean freight changes to land transport. The change-over, warrants special type of heavy duty handling equipment. The equipment and the process necessitate deep seated foundations. On one side of the berth, deep drafted ships would be berthed. But adjacent to this heavy duty cranes would be operating at the deck level. Berths are of various types. Some are founded on piles and may project into water. Some operators prefer a retaining structure. At the port of Krishnapatnam, a retaining structure was preferred. Dredged level at the berth was to be -20. Deck of the berth was at +4.3. This meant that the height of retention of soil was 24.3m. Ports are generally located near the coast. Subsoil in the port area generally consists of cohesive material of low shearing strength. The berth has to cater to imposed vertical and horizontal loads.Structural functionFor bulk cargo and containers, berth has to support the two crane tracks. These tracks will carry heavy wheel loads of the crane. Besides, the space between the tracks would be used for stacking of cargo or hatch covers. In short, the deck will be subjected to heavy surcharge. This vertical load will manifest as additional lateral force on the retaining wall. Since the height of soil to be retained is high, it is a practice to relieve the lateral earth pressure due to the heavy surcharge of the wall. This is done by providing a relieving platform. The surcharge of superimposed load on the deck and the self-weight of the soil up to a few metres below would be relieved by a suitable platform. This vertical load would be transferred directly to deeper levels through piles. Mooring pull is a horizontal force exerted by the vessel on the bollards towards water side. Berthing force is exerted by the vessel during berthing, through fenders and acts towards land side.Diaphragm walls are usually employed as the retaining face. If the height of retention is less, these walls can cantilever out but in the case of large retention, they have to be tied back. The ties are to be anchored on to suitable arrangements like a dead-man or an A-frame. Berthing structure in the early stages at Krishnapatnam port is shown in fig 1."

Jan 1, 2015

By Abid Adekunte

Traditionally, designers and contractors provide additional external supports to retaining walls through the use of tie-back anchors or braces. Both approaches are known to have their shortcomings; braces limit working space within excavation areas, while tie-backs are seldom used in built-up areas where intrusion into adjacent property of non-cooperative owners has to be avoided or in situations where sensitive structures exist behind the wall. This paper focuses on the design, construction and monitoring of deep excavation support systems on two separate projects located in different ground conditions in the Republic of Ireland. On both projects, conventional ground anchorage and propping were inapplicable. This led to the development and application of two different novel solutions on both projects. Methods of wall performance monitoring on both sites also differ. Wall monitoring results show these innovative methods to be safe and effective. Advantages of the novel solutions over traditional approaches are highlighted.

Jan 1, 2010

By Chandramohan P. V

A unique tension pile where the pull is at a point a certain distance below the top of the pile. The pull is transferred by a cable consisting of high tensile strands. The HDPE duct of the cable prevents bond between the strands and pile concrete in upper portion. While soil friction on the pile will act downwards on the whole length, there is tension in the bottom portion of pile, there will be compression at the top portion.

Nov 1, 2022

By Dino Kartofilis, Rick Deschamps, Giovanni (John) Bonita

"Anew condominium complex in Arlington, Va., presented some formidable constraints. One was the requirement for a permanent retaining wall to support a 48.5-ft (15-m) cut and an existing 16- story building on top of the slope. Another was the adjacent property owners’ refusal to allow tieback anchors to encroach on their property. The General Contractor (GC) proposed an innovative design incorporating vertical concrete load-bearing elements (LBEs) supported by post-tensioned tiedowns. The owner accepted and the project was successfully completed in 2007.The original designer had proposed a system that included a temporary, raked soldier pile and lagging wall and a permanent cantilever retaining wall with a large piled footing. The system was potentially costly and its constructability questionable.The GC then asked for a design-build alternative to reduce costs and enhance the schedule. The first idea was a diaphragm wall with vertically anchored T-sections. However, configuring a crane to excavate perpendicular sections using grab equipment seemed impossible. There were also utilities approximately 25 ft (9 m) from the existing building, two tiered retaining walls down the slope and a large swimming pool at the base. However, the GC was committed to providing a stable bench 20 ft (6 m) wide along the wall alignment to support the crane.The design evolved to single bite panels using diaphragm wall technology, commonly called LBEs, or barrettes, when they carry vertical loads. For this project, 44 LBEs were horizontally spaced at 9 ft (2.75 m) on center, oriented perpendicular to the wall, extending into bedrock and anchored vertically on the upslope side to resist overturning moments. They were essentially large soldier piles that provided both temporary and permanent support of excavation.An unusual formal agreement was established with the GC to complete the work based on pricing, and prior to completion of final design. This arrangement allowed for an exchange of ideas that increased project efficiencies and lowered costs — without the fear that design concepts would be “shopped” to competitors."

Jan 1, 2009

By Armin W. Stuedlein, Jim Zammataro, Bernie Hertlein, Daniel Belardo, Qiang Li, Antonio Marinucci

"An experimental program focusing on four drilled shafts was conducted to determine the effect of high strength steel reinforcement bars on lateral resistance, steel casing on axial and lateral resistance, and steel casing without internal reinforcement on lateral resistance. Thermal Integrity Profiling (TIP) Thermal Wires and crosshole sonic logging (CSL) access tubes were installed in each shaft, and thereafter the corresponding non-destructive testing (NDT) was performed on each shaft to assess the integrity of the shafts and to compare the results from the different NDT methods. The results of the CSL tests using scored PVC tubes are compared against those conducted in 73/56 fully-threaded steel hollow bars, whereby the results indicated that the threaded bars served as a good host for performing the CSL tests. The data from the TIP Thermal Wires is compared against the results from the CSL tests for each of the four shafts, and the similarities and discrepancies between the two methods are discussed. This paper will serve as a reference to those interpreting the measurements and data obtained by performing nondestructive integrity tests on drilled foundations.INTRODUCTIONNon-destructive tests (NDTs) embody a set of critical tools for the evaluation of the integrity of constructed deep foundations, particularly for cast-in-place foundation elements. Construction defects may require the rejection of the foundation element by the owner’s representative, resulting in costly repairs or replacements and delays to the project schedule. The use and appropriate interpretation of the results from the NDTs provide the information required when evaluating the integrity of these constructed elements. A cooperative research program was conducted to assess the effects of various construction variables on the axial and lateral performance of drilled shaft foundations, which provided an opportunity to compare the established Crosshole Sonic Logging (CSL) test method to the newer Thermal Integrity Profiling (TIP) Thermal Wire method. This paper presents an overview of the experimental program performed at the geotechnical test site at Oregon State University (OSU), details of the CSL and TIP installation and testing methods, and the results of the NDTs on the constructed drilled shafts. Because one of the shafts was constructed with fully-threaded longitudinal steel hollow bars, this experimental program also allowed the assessment of the use of the hollow bars as access tubes for the CSL tests. Both the CSL and TIP test methods indicated that the shafts were of good quality and free from defects or anomalies; the data obtained using the TIP method also provided an estimate of the as-constructed shaft diameter and the reinforcement cage alignment, which will prove helpful when back-calculating axial and lateral load transfer during future loading tests."

Jan 1, 2016

By Ivan Hee

The 2.5km long bridge over the Beauharnois Canal and St. Lawrence Seaway is a major structure in the new Autoroute 30 project near Montreal. Foundations for the bridge consist of footings on bedrock, driven piles, and drilled shafts. This paper describes the design, verification, and construction of 1.85m diameter drilled shafts socketed into very strong and abrasive dolomitic sandstone. Two loading tests on sacrificial, heavily-instrumented, 1.18m diameter test shafts using Osterberg load cells were performed, with telltales installed to monitor a possible rock cone failure mechanism. The loading tests resulted in a revision to the initial design and provided a greater understanding of the cone uplift mechanism in rock. Insights gained are discussed and economies of the load testing program presented. Construction methodologies are also presented.

Jan 1, 2011

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"Previous studies revealed that the helix deflection reduced the end bearing capacity of screw pile in dense ground even if the installation process is completed with minimal soil disturbance. The ultimate end bearing capacity in dense ground is difficult to achieve during the full-scale pile load test due to the limitation of the loading system. Therefore, in the present study, model scale of testing is selected to investigate the effect of helix deflection on load settlement behavior of single helix screw pile under increasing stress level. It is observed from the test results that the applied surcharge pressure, which is used to simulate the effect of stress level, is decreased with increase in model ground thickness. This decrease in the stress level is due to the frictional resistance between the container wall and sand. It is also observed that the end bearing capacity of screw pile increases with the increase in stress level but at gradually decreasing rate. The test results indicated that the helix deflection during the pile load test should not be more than critical deflection (0.72 mm average) of the helix to avoid any reduction in the end bearing capacity of screw pile. The helix deflection, which is measured after the pile load tests are also compared with the equations of flat circular plate having uniformly distributed load over the plate with simply supported and fixed inner edges.INTRODUCTIONThe screw pile consists of a central steel shaft with one or more helices attached at different location on the central shaft. The installation mechanism of screw pile consists of torque and pushing force. The screw pile installation mechanism can affect the unit weight of the ground during its installation. This effect is small in cohesive soils but it is quite noticeable in loose to medium dense sands (Adams 2011; Santos et al. 2013). The pushing force should be controlled in such a manner that pile penetration should be at least 80% of the pitch of the helix, during each revolution (Perko, 2009)."

Jan 1, 2017

By Zhou Lu-Jian

The Port of Shekou is situated at Shenzhen Bay on the east bank of Lingding Ocean. Its coastline is about 6 km long and the water depth near the shore is Favourable. Across the bay is the ' New Territories " of Hong Kong. The port is at a distance of 22-23 seamilesaway from center of Hong Kong and 80 seamiles to Huangpu Harbour of Guangzhou, its highway links with Shen-Guang Highay. Since 19 79 China Merchants Group of the Transportation Department, began to set up Shekou Industrial Zone, the port has been developing and flouri­shing in business. With 15 large or small berths in all, the present portline is 2600 m, and the annual cargo throughout is over 3,000,000 tons and the annual passenger traffic is about 2,000,000 persons. Equalling a medium-scale seaport, it has been officially approved as an oceangoing transit port by the ministry of Transportation. The construction of Shekou port is chara-terized by the self-collected funds and the short construction period. In view of this, the optional plan of the port structure must serve the requirements of simplicity in struture, economy in mate­rial and speed in construction. That accounts for the most application of the sheet piling type to the port in Shekou. Once the project was approved, the cons­truction started. Only within an average period of 7-8 months, a deep water pier was completed and put into operation, which covered series of processes from exploration, designing, tender for con­struction to completion.

Jan 1, 1991

By Frederick C. Rhyner

This paper describes the design and construction of two high-capacity rock anchors to restrain a supplementary backstay for the Bear Mountain Bridge, which is a suspension bridge spanning the Hudson River about 40 miles north of New York City. The supplementary backstay was installed to relieve a portion of the tension in the southern main cable, which had been creeping in recent years. The two new rock anchors were 1,200 kip capacity each, installed at a batter to depths of 59 feet. This paper describes the subsurface investigation, group capacity analysis, installation and load testing. The rock anchors included strain gages connected to the monitoring system for the bridge. The paper describes the long term strain gage data which shows no change in stress distribution in either anchor.

Jan 1, 2010

By S. Merjan

Three papers were presented for discussion at the conference: 1) Instrumented driven steel tube piles at Canary Wharf; author: A. R. Gaba, United Kingdom. The author described the Canary Wharf development in the London Docklands, and in particular, the decision to build over the water by driving open-ended steel piles 25m in length into the sands below the soft estuarine deposits. The tubes were then filled with concrete above the sand plug (usually 17m below pile head). Three trial piles were instrumented with: a) resistance strain guages on the inside of the tubes; b) vibrating wire guages on the re­inforcement of the concrete. The trial piles showed elastic behaviour in five cycles of lateral loading, while the verticle load tests showed a definite bi-linear load-settlement behaviour. The initial stiff portion was a result of frictional staff resistance, both inside and outside the tube, with the soil at the base contributing at higher settlements. Loads were taken to three times working load, with no imminent signs of failure.

Jan 1, 1991

By James L. Vinson

Wilbur Smith Associates (WSA) has provided planning, engineering and construction oversight assistance to the Tennessee Department of Transportation (TDOT) for three construction projects intended to widen and improve segments of I-40 and associated interchanges in Knoxville, Tennessee. The projects are within the karst terrain of the Valley and Ridge Province. Subsurface conditions are characterized by an irregular rock surface coupled with differential weathering. Because of the projects? impact to local and interstate motorists, consideration was given to innovative planning, materials and construction practices that could accelerate construction. Two innovative deep foundation measures included rock-socketed pipe piles, which act as both foundations and substructure elements for a bridge?s interior bents, and the first widespread use of rock-socketed drilled shafts as bridge foundations on a TDOT project. The pipe piles were used at a site with significant cavities within the limestone bedrock. This resulted in design verification and constructability difficulties that required delays, but measures were ultimately employed to produce a sound foundation system. Over 110 drilled shafts have been constructed at sites with generally low solution activity. Relative to H-pile footings, which were included as an alternate foundation, they have apparently allowed accelerated construction at a competitive cost.

Jan 1, 2006