Search Documents

By Derek J. Lennon

Ground conditions in central Glasgow generally comprise loose granular deposits overlying stiffer soils. CFA piling would normally be preferred for urban sites in these ground conditions, but flighting of the superficial deposits has on occasions resulted in building damage. Over the last five years rotary bored piling with vinyl polymer support fluid has proved to be an economic alternative to bentonite slurry. Two case histories in central Glasgow are described in this paper, one for piles founding in granular soils and one for piles founding into bedrock. A comparison is made between the methods required for disposal of the liquid waste from bentonite and vinyl polymer slurries.

Jan 1, 2006

By Mohammad Ali Rowshanzamir, Mehdi Aghayarzadeh

"This article is an effort to improve our understanding of the performance of geogrid retaining structures (GRS) through numerical analyses. The numerical modeling utilized a commercially available finite difference program, FLAC3D. In this context an extensive parametric study has been carried out on two different GRS walls (vertical reinforced block and inclined reinforced block) to investigate the influence of internal design factors such as soil strength properties and reinforcement stiffness on the performance of these walls. The main purposes of the parametric study were to (1) investigate the sensitivity of the modeling results to the input material properties, (2) examine the influence of the internal design factors on the performance of GRS retaining structures, and (3) improve the internal design of GRS walls on the basis of the working stress information obtained from the parametric study. Based on the analyses results, it was revealed that GRS walls with oblique reinforcement and reinforced block (rotated against natural backfill) have much better performance in terms of reduction in the stresses and strains of reinforcing elements as well as decrease in the wall lateral and vertical displacements in comparison with vertical reinforced block (conventional wall). For example, with 12° inclination of the wall reinforced block there was 50% reduction in the backfill settlement. Also increasing the reinforcement stiffness amount from 10MPa to 50MPa decreases the wall face displacement more than 50% in both GRS walls.INTRODUCTIONOver the past few decades, Geosynthetic- Reinforced Soil (GRS), a soil mass reinforced by geosynthetic layers to restrain the soil lateral deformations, has been employed in the construction of many types of earth structures, including retaining walls, embankments, slopes and bridge abutments. In fact GRS structures are typically more flexible (hence more tolerant to differential settlement), more adaptable to low quality backfill, easier to construct, require less over-excavation, and more economical. Nevertheless, there is a need for an accurate design tool that can predict the performance of GRS structures under working stress conditions and can predict their failure loads as well.Many studies have been published on the performance of the soil reinforced walls such as Isabel et al., 1996; Bathurst et al., 2000; Kazimierowicz-Frankowska, 2005; Nernheim and Bathurst, 2008; Chen and Chiu, 2008 Correia et al., 2012; Erlich et al. 2012. Several numerical studies have also been made throgh finite elements and finite difference techniques on reinforced soil retaining walls to analyze the wall deformations (e.g. Hatami et al. 2001& 2006, Liu and Won 2009, and Abdelouhab et al. 2011). A limited laboratory research has been reported indicating of improving effect of tilting face on GRW performance (Chen and Chiu, 2008). However no major numerical study was found on the effects of face or reinforcement tilting."

Jan 1, 2017

By Dongwook Kim

Recently, load and resistance factor design (LRFD) is gradually being adopted internationally in geotechnical design due to the advantages of LRFD over the existing allowable stress design (ASD). LRFD is a more advanced design method compared to the ASD because resistance factor is calibrated based on the reliability analysis for a given target reliability index. Target reliability index changes with the importance of the structure. Typically, target reliability index of offshore foundation is less than those of onshore. The widely-used Imperial College Pile (ICP) design method is used for the calculation of pullout capacity of driven piles. The uncertainties regarding pullout capacities of driven piles are assessed using the statistical data reported in the literature. The first-order reliability method (FORM) is used to calibrate resistance factors for the pullout ultimate limit states of the driven piles for three different levels (2.5, 3.0, and 3.5) of target reliability index. The load factors used in this paper are the ones proposed in the AASHTO LRFD bridge design specifications.

Jan 1, 2010

By Carl D. Ealy

Work is being done to web enable the FHWA Deep foundation Load Test Database. Originally designed to function in the client server environment via modem, access to the database both for data maintenance and user queries has been upgraded to take advantage of the Internet and current and future information technology innovations. The DFLTD will be part of an Automated Geotechnical Information and Design Aid System, the object of which is to assist those involved with managing and maintaining our nation's highway infrastructure. The system will also meet the needs of university and other research institutions for a statistically meaningful source of high quality data for the development and verification of improved analysis methods, in-situ testing methods, etc.

Jan 1, 2002

By D. E. Sherwood

Mr. Tamaro introduced his paper which concerned the construction of foundations for the buildings and related infrastructure of the World Financial Center on a reclaimed shoreline site at the Southern tip of Manhattan Island. This large project presented difficult design and construction problems, both geotechnical and structural. All structures were supported by foundations carried to rock. Two of the buildings were supported by conventional pier (pad) foundations constructed within diaphragm wall cofferdams. The remaining structures were supported by either piles to rock or caisson (large diameter) piles with socket depths drilled through the rock of up to 7.6 metres. Underground services, railway and proposed road tunnels all affected the installation of foundations. The proposed road tunnels for the new six lane 'Westway' would involve an excavation 12 metres deep adjacent to and under three buildings. This problem was solved by an agreement that tower windloads would be taken by the tower foundations and not distributed through the basement walls. This was achieved by a system of battered caissons founded on the rock and arranged so that adjacent caissons were founded in different rock masses. Diaphragm walls were restrained using tie backs. Ground testing indicated an exposure to D.C. stray current corrosion of all underground construction. As a result all of the foundations were isolated from the ground by non-conductive materials. In the case of piles and caissons the reinforcing for the caisson was fully protected by concrete and all outside steel used for the installation of piling was considered sacrificial and not used in the computation of long term load carrying capacity.

Jan 1, 1991

By Christian B. Woods, Joe C. Drumheller

"Kenneth A. Huber, P.E., Langan Engineering & Environmental Services, New York, New York, USAThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. The Prudential Center site encompasses an entire city block that had a varied history of uses ranging from a cemetery in the late 18th century, to a rail yard and train station for the now-defunct Central Jersey Rail Road in the 19th and early 20th centuries, to commercial development in the latter half of the 20th century. Each of these prior uses presented challenges to the design and construction of the Prudential Center that required innovative engineering solutions, including: archaeological investigation and exhumation of the former cemetery occupants, protection of historic buildings surrounding the site, and extensive demolition to remove old train bridge foundations.The design team was required to develop potential foundation systems for the arena. Several foundation concepts were evaluated for cost and constructability, including: driven piles, drilled shafts, and shallow foundations on improved subgrade. Following a detailed cost analysis and value engineering exercise, the decision was made to support the arena on spread footings following the completion of a multi-phased ground improvement program consisting of a combination of dynamic compaction and removal and replacement. To evaluate achievable allowable bearing pressure as part of the design, a dynamic compaction test section was performed within the building footprint prior to the start of production work; this resulted in an increase of the allowable design bearing pressure from 2 tons per square foot (tsf) to 3 tsf. This reduced the expected foundation costs by 30% and gained sufficient time in the schedule to allow for the completion of the arena in time for the New Jersey Devils 2007- 2008 hockey season.BACKGROUNDThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. After several years of negotiating between the City of Newark, local landowners, area developers, and the Devils themselves, a deal was finally struck to erect Newark Arena, now known as the Prudential Center, right next to City Hall. This is not to say, however, that once the site location was finalized, that no further challenges were encountered in the construction of Newark’s new crown jewel."

Jan 1, 2015

By Y. Z. Wang

Zhengzhou Yellow River Highway Bridge, which is under construction, has a total length of 5550 meters with bored cast-in-place concrete piles as the foundations of its piers which have a diameter of 2.20 m with a length of approximately 65 m. This paper attempts, through the introduction of the said bridge's footing pile design and construction, mainly to give an account of the following points: 1) experiment and research on deep friction pile with a large diameter, 2) calculation of vertical carrying capacity of the pile with a large diameter, 3) analy­sis of horizontal forces the footing-piles of the column-shaped piers, 4) application of normal and reverse-circulation rotary drilling technologies to the construction of bored cast-in-place concrete piles with a large diameter and 5) applying super-sonic impulse on destruction detective device to examine the quality of the pile concrete.

Jan 1, 2010

By P. Middendorp, Gerald E. H. Verbeek

"INTRODUCTIONStatic Load Testing (SLT) is generally considered the pile testing method that provides the de-facto answers regarding pile capacity and load-deflection behavior. However, as this testing method is time consuming and costly, alternative pile testing methods are applied, such as High-Strain Dynamic Testing (HSDT), commonly referred to as Dynamic Load Testing (DLT), and Rapid Load Testing (RLT), which includes Statnamic Testing (STN) and the Fundex Pile Load Tester (PLT). Extensive descriptions of these pile testing methods as well as comparisons of the results from these two methods have been widely published, but little is written on the choice between HSDT and RLT. This article will address this issue for concrete piles by discussing five different aspects that should be considered when making a choice between HSDT and RLT for either cast-in-situ piles or precast driven piles. TIMINGThe timing of the pile load test is independent of the testing method. For cast-in-situ piles load testing is performed some time after the pile has been installed (to allow the pile to obtain the compressive strength required to withstand the test load), while for precast driven piles load testing is performed after a so-called set-up period following pile installation (to allow the soil to recover from driving induced disturbances and, at least in most cases,regain strength).In other words, the timing of the test does not affect the choice of the testing method.ACCURACY OF THE APPLIED LOADWhen a pile is tested by RLT the applied load is measured by a calibrated load cell placed on the pile head, just as it would be during SLT. This means that the error in the applied load value is less than 0.1% of the maximum range of the load cell.However, when a pile is tested by HSDT the load is calculated from the measured strains, which means that the outcome is dependent on the pile material properties. In this case the applied load (F) on the pile head is calculated by multiplying the measured strain (?) with either the calculated or estimated elastic modulus of concrete (E) and the pile cross section (A).The elastic modulus is generally back calculated from the (average) stress wave velocity (c), which in turn is derived from the reflection time (T) it takes for a stress wave to travel over the pile length (L) from the pile head to the pile toe and back to the pile head."

Jan 1, 2006

By Jinung Do, Sung-Ryul Kim, Juhyung Lee

"Model tests have been performed to investigate the vertical, horizontal and cone tip resistances of bucket pile embedded in sand by different installation methods; suction force by pump and jacking force by actuator. Micro-cone penetrometer is used to evaluate the variation of the effective stress inside and outside of the pile after installation. As a result of vertical pull-out test, the jacked pile shows 3 times larger resistance than the suction-installed pile. For horizontal pull-out test, the ultimate horizontal capacity and the slope of load-displacement curve on the suction-installed pile decreases by 22% and 40%, respectively, compared to the jacked pile. In cone penetration test, inside cone tip resistance of the suction-installed pile is about 40% smaller than the jacked pile, which indicates that the effective stress is reduced due to upward seepage of bucket pile in sand by suction force. Therefore, installation methods can affect the behavior of the bucket pile significantly.INTRODUCTIONA suction force occurred when bucket pile penetrates into sandy soils induces seepage flow into the bucket pile so downward seepage near the outside of bucket pile causes to increases the effective stress, while upward seepage inside the bucket pile decreases the effective stress (Mahn, 2005; Fig. 1). The effect of induced seepage causes to reduce the penetration resistance during installation. On the other hand, reduced effective stress can decrease the horizontal and vertical capacities of bucket pile by significant disturbance at the tip of the bucket pile due to the flow net. Due to the complexity and difficulty considering the effects of suction installation, many previous researchers generally have neglected the effect of suction installation in their experiments. Therefore in this study, the effects of suction installation on resistance of bucket pile is examined."

Jan 1, 2016

By Matthias Pulsfort, Jiarui Du, Torsten Wichtmann, Achim v. Blumenthal, Diethard König, Rowena Verst

The influence of the interaction between support fluid and soil, e.g., filter cake formation, on the shear stress transfer in the soil-concrete interface of diaphragm walls and bored piles is still controversially discussed. Actual research on the soil-concrete interface using bentonite suspensions indicates that shear stress transfer is underestimated by existing standards. Investigations on the soil-concrete interface using polymer solutions are rare. Therefore, complementary field investigations and systematic laboratory studies were conducted to analyse the soil-concrete interface using both bentonite suspensions and polymer solutions. Thickness and composition of real-scale filter cakes were investigated on several slurry wall construction sites, where bentonite suspensions were used. Direct shear tests (60 mm x 60 mm) were executed for soilbentonite mixtures with varying amounts of bentonite and different granular fines representing a realistic bandwidth of in-situ filter cake compositions. Larger direct shear tests (300 mm x 300 mm) with preceding horizontal penetration, subsequent vertical tremie concrete placement, and filter cake consolidation were performed using both bentonite suspensions and polymer solutions. The results support the view that shear stress transfer in the soil-concrete interface can be described by a wall friction angle in a range of 25° to 30° for bentonite suspensions and between 35° and 40° for polymer solutions in non-cohesive soils.

May 1, 2022

By Maurice Bottiau

When dealing with displacement auger piling, some general and fundamental issues have to be considered, irrespective of the system. More than with other pile types, the interplay between the soil conditions and the design and execution is of outstanding importance. This paper intends to address these issues and to summarize some critical matters in terms of design, execution and control such as : ? Importance of a reliable soil investigation ; ? Summary of the design as it is addressed in Europe for this category of piles ; ? Criteria for a good choice and control of the correct asset of the piles ; ? Importance of the concreting phase; ? Relation between the power and the engine characteristics of the drilling equipment with the final bearing capacity. For each of these issues detailed examples will be given as well as results of load tests and in-situ control during execution.

Jan 1, 2003

By P. B. Kelleher

Most of the piers and other pile-supported marine structures in the New York City Harbor area were constructed prior to the widespread use of currently available pile protective systems. As a result, the support piling of many existing marine structures have experienced deterioration to an extent that their structural sufficiency is impaired long before the useful life of the structures they support is over. This situation presents special and unique problems of how to restore the structural integrity of these piles while at the same time allowing full use of the structures they support. Spearin, Preston & Burrows is a 100 year old New York City-based marine construction firm specializing in waterfront and foundation construction. In recent years it has undertaken and successfully completed several unusual projects in the New York City Harbor area involving the rehabilitation of existing, deteriorated piling underneath major, economically important marine structures. This work was accomplished using techniques that permitted full use of these structures. Several different pile rehabilitation systems were used, each having their own particular application to the deterioration problems of the piles supporting each structure.

Jan 1, 1989

By Arash Khosravifar

The seismic design of extended pile shafts for the combined effects of dynamic shaking and liquefaction-induced lateral spreading is investigated using nonlinear dynamic finite element analyses (NDA). Results of NDA parameter studies are used to illustrate how inertia and lateral spreading loads combine during shaking. The NDA results are used to evaluate equivalent static analysis (ESA) methods. Implications for design practice are discussed.

Jan 1, 2010

By James C. Scott

Compression and tension load testing were performed on bored concrete piles installed to depths of 18 to 34 meters below excavation levels for a large mixed-use development in Kuala Lumpur, Malaysia. The 900 mm diameter piles were installed in weathered graphitic schist bedrock. Load testing confirmed the side shear and end bearing capacities of the piles. The work formed part of the investigations for the 56,000 m2 site which includes a 79-story office tower, hotel tower, apartment tower, retail complex, and plaza area underlain by 4 to 6 basement levels. The paper provides the results of the site investigations, pile-load testing procedures, pile-load settlement behavior, and shaft load distribution.

Jan 1, 2007

By J. Pei

The studies of dynamic measurements using stress wave theory has commenced in China. This paper introduces some practical experiences using "CASE method" in Shanghai showing applications of dynamic measurement to determine ultimate bearing capacity of pile, the change of capacity due to set up, determining the optimum bearing layer during pile driving, the efficiency of hammer system and integrity of pile and discussions of method concered.

Jan 1, 2010

By S. E. Stallibrass, A. M. McNamara, J. P. Panchal, Leonardo M. LaLicata

Urban development in congested cities requires a better exploitation of the available surface, leading to taller structures. These buildings are usually founded on piles that have to be increased in dimension to accommodate the larger loads. Consequently, both the cost and the carbon footprint of the pile foundations rises. An alternative option is to improve pile performance by enhancing shaft capacity, which is commonly the most important factor in determining the ultimate capacity of a pile constructed in a clay soil subjected to axial load. For piles in stiff clays, such as London Clay, the soil/pile friction may be increased by profiling the side walls of a bored cast in situ pile with small discrete “impressions” such that the latter form nodules on the shaft of the concreted pile. The results from centrifuge and full scale field tests showed that the impression pile represents a viable technology to enhance the shaft capacity as they provide an increase in capacity of 40%. Alternatively, reduced length impression pile can be used. This paper explores the implications of the impression pile technology on the potential carbon saving.

May 1, 2022

By Amr Sallam, David Thompson, Moataz Hassan

"The Little Lake Harris (LLH) Bridge was constructed in 1951 to replace the eastwest County Road 48 Bridge connecting the towns of Howey-in-the-Hills and Astatula in Lake County, Florida, United States. The 78-span bridge carries two lanes of traffic, is 3,130 feet long, and 36.1 feet wide. The concrete deck is supported by steel I-girders carried by one row of 18-inch square precast concrete driven pile. In the late 1980's, slight settlements were observed in several bents. In 1990, Florida Department of Transportation (FDOT) initiated annual survey of deck elevations during bridge inspections to monitor settlement. Due to the slow nature and magnitude of settlement, substructure instability was not a major concern to the department. However, public concern over the settlement and rough ride of the bridge continued to rise. FDOT contracted Kisinger Campo & Associates Corp. (KCA) to provide the needed design to correct the dips in the riding surface and minimize future settlement. KCA's initial design was based on the concept of ""helper bents"" at the settled bents in order to restore the bridge to original elevation. Estimated construction cost for seven helper bents was about $3.3M. FDOT requested evaluating other alternatives to reduce the cost of the bridge restoration. KCA involved the geotechnical consultant, Terracon Consultants, Inc. (Terracon), to perform a peer review and provide an economical alternative solution. Jacking and shimming the bridge was determined to be both technically viable and economical with a total cost of less than $300K. The design was completed in March 2010 and construction was completed in February 2011. This paper provides an overview of the LLH Bridge history, summarizes the evolution of the design methodology including the findings of the geotechnical study and presents lessons learned during the design and construction of the project.INTRODUCTIONThe Safety and Preservation of the State Highway System is the top priority of the FDOT. Therefore, FDOT initiated a bridge management program that starts with conducting biennial safety inspections performed by Certified Bridge Inspectors (CBI). The inspection reports together with the CBI’s recommendations are reviewed by a registered Professional Engineer (PE) and work orders are issued with priority ranking depending on the severity of the bridge deficiencies. If the scope of work is considered beyond the in-house crews’ capability, the work is then included in a contract for and bid. LLH Bridge was a little different. It was initiated in direct response to number of complaints the FDOT District 5 Structures Maintenance Office (D5SMO) received regarding settlement of the Little Lake Harris Bridge."

Jan 1, 2015

By Joshua R. Omer

A numerical model is developed for predicting the load transfer and settlement behaviour of vertically loaded, bored cast in-situ piles. Based on analysis of full-scale pile tests, closed-form equations are formulated to uncouple the shaft and base transfer resistance components of the pile/soil system. Appropriate parameters are introduced to take into account: (i) the shaft resistance distribution in unlined and partially lined piles, (ii) the effects of ?soft toe? (voided toe pile) behaviour on base resistance development. For convenience, an interactive computer program has been developed in Matlab? with a user friendly interface system. The program can be applied to predict the complete load-settlement curve and axial force distribution in bored cast in-situ piles if reliable soil test data are available. To demonstrate its validity, the proposed method is applied to 4 test piles, which are also analysed using two previously published methods: (a) elastic solution method and (b) layer discretisation method. Methods (a) and (b) above are based on load transfer (t-z) and finite element models respectively. It is shown that the proposed method yields axial force distributions and load-settlement curves that are in good agreement with the observed pile test data.

Jan 1, 2010

By Mihir B. Roy

"Coal transported by rail for Thermal Power Plant in Haldia, West Bengal, India, was to be received and stored in Coal Complex comprising of Wagon Tippler, Track Hopper, Junction Houses and network of horizontal and inclined tunnels. The site was very soft with high ground water level. Deep excavation and dewatering posed great difficulty. Original plan was to drive about 1000 m of steel sheet pile and well sinking which had major impact on cost and time. High ground water was identified as the main problem. Controlling water level and maintaining it would allow open excavation over major areas. Scheme for lowering aquifer with one and two-stage well-point dewatering system was developed following basic principles of groundwater and seepage. Arrangements of wells, installation and pumping were worked out in detail. Water levels could be lowered below bottom levels of excavation. Design of sheet pile was modified under lowered ground water condition. Overall length and depth of sheet pile were reduced drastically. Open excavation was possible in segments over major areas. The scheme was highly successful in smooth and fast progress of underground works. The works were completed safely months ahead of schedule time and with significant saving in cost.INTRODUCTIONThe Coal Receiving Complex of thermal power plant comprised of 250 m long 8 m deep Track Hopper (TH), 12 m deep Wagon Tippler (WT) with provision for addition of another Wagon Tippler. Track center lines of TH and WT were very close. Coal unloading facilities were connected with a network of underground tunnels and Transfer Points (TP) upto Pent House (PH). The facilities were optimized in a compact layout within about 400 m x 120 m area. Initially excavation for TH was started adopting side slope of (1 V : 1.5 H) with 2 m wide berm and dewatering by in-pit sump and pump. When depth of excavation reached about 5-6 m, failure occurred over a long stretch as shown in Figs. 1a - 1b photos. Further work was stopped to develop scheme for carrying out deep excavation and civil works safely."

Jan 1, 2015

By Kenneth M. Berrry

A unique situation has developed at an abandoned coal mine in St. Clair County, Illinois. Subsidence features have been observed at the ground surface over the mine including settlement of a pair of bridges for Illinois Route 158. The Illinois Department of Transportation (IDOT) is currently replacing the two bridges. Foundation treatment for the two new bridges included backfilling the mine void. The light rail system for St Louis (MetroLink) is also constructing a bridge over the same abandoned coal mine less than 1000 ft from the Route 158 bridges. The new MetroLink bridge is being constructed using piles which extend through the coal mine and overlying bedrock in order to transfer the loads to below the mine floor. The differing foundation types for the IDOT and MetroLink bridges were due to geometry and economic factors involved with the individual structures.

Jan 1, 2001