Search Documents

By James A. Mason

The State of California has instrumented numerous buildings, bridges, and dams throughout the state with earthquake recording devices. These accelerometers are strategically placed to measure the response of the structure to a specific seismic event. This comprehensive program enlightens the field of seismic engineering after each earthquake. The Office of Strong Motion Studies, California Strong Motion Instrumentation Program, a sub-branch of the Division of Mines and Geology, provides a professional service unequalled in the world. Within hours of a local earthquake, a preliminary report with the epicenter / hypocenter, structural damage, and time history records are available to all interested parties. The included partial report in the appendix, see section 5.1, is one of the reports that C.S.M.I.P. produced after the Loma Prieta Earthquake of October 17,1989. The diagram on the cover is even of interest. This is a small portion of San Francisco. The values on the diagram are the recorded maximum horizontal ground accelerations at that location in the city. For example, the acceleration at Yerba Buena Island was 0.06g. (The "g" refers to the acceleration of gravity. Thus, a 0.06g acceleration refers to the force, F=m*a, that the structure would experience. For this case, the force would be six percent, 6 % , of the mass of the structure.) Yet, directly on the other side of the Bay Bridge, at Treasure Island, the acceleration was 0.16g. Yerba Buena Island is a natural island composed of hard granular material. Whereas, Treasure Island is a man-made island of imported filled. Here one can see the absorption / transmission difference between hard material, which interact with short seismic wavelengths, and soft cohesive material, which interact with long seismic wavelengths.

Jan 1, 1993

After the Loma Prieta Earthquake, which caused major damage to viaducts in the Bay Area, the California Department of Transportation set up a test programme for foundation piles. Funderingstechnieken Verstraeten B.V., beter known as Fundex, was approached, since one of the piling systems of Fundex, named Tubex, is extremely suitable in areas sensitive to earthquakes and we were very much interested to prove the capabilities of this piling system. Equipment For the installation of Tubex and Tubex grout-injection piles special piling equipment is required. Since our company is not only a contractor, but also a designer and manufacturer of piling equipment, all special equipment for our range of foundation techniques is designed and built by our own piling equipment department. For the installation of both Tubex piles and Tubex grout-injection piles for the Caltrans test programme, the following pieces of equipment were selected: a) Fundex F12 piling rig b) Drill table c) Hydraulic powerpack d) Grout mixing unit and high pressure pump

Jan 1, 1993

By Lawrence F. Johnsen

In 1989, the Connecticut Department of Transportation authorized the evaluation and design for a reconstructed Route 1 bridge over the Quinnipiac River in the City of New Haven, Connecticut. The project extends from the intersection of Route 1 with East Street, easterly for approximately 3/4 mile to the intersection of Route 1 with Wheeler Street and Stiles Street. The reconstructed roadway will be relatively on-line and widened to provide for four lanes of vehicular traffic and a single-track railway line. The existing bascule bridge and approach spans, which were constructed in 1924, will be replaced by a 270-foot span lift bridge and new approach spans. The lift bridge will have a main lift span weighing approximately 3000 tons, second largest after the Burlington Northern Bridge over the Williamette River in Portland, Oregon. The new bridge will widen the navigation channel to 24 0 feet and provide vertical clearances of 13 feet when closed and 62 feet when open. The project is located in an industrial area. Adjacent properties include retail gasoline sales, auto repair, railroad transport and bulk storage of petroleum. Existing structures include the Yale Boathouse and several retaining walls serving as containment dikes for petroleum storage tanks. The Yale Boathouse, located on the east bank of the river, was constructed in 1909-1910 and is eligible for listing in the National Register of Historic Places.

Jan 1, 1993

By Donald A. Bruce

Pin Piles are small diameter, bored, cast-in-place piles used to underpin structures. They were first employed over 40 years ago in Italy, and have been used in the U.S. since the late 1970's. However, it is only in the last few years that their full potential in terms of load holding capacity has been exploited: whereas 100 kip working loads typified former practice, ultimate loads approaching 700 kips have recently been recorded for Pin Piles founded in sand. In order to better understand the actual performance of these piles, fundamental research has been conducted by a consortium of industry and academia. This paper describes the advances made in the laboratory and full scale field testing programs. In particular, the extensive field tests have been conducted in a variety of materials in which different pile configurations have been cyclically tested to failure. By using this test method, the elastic performance of the piles has been examined and so the progressive interfacial debonding phenomenon has been studied. This has led to the development of the Elastic Ratio concept which is proving extremely useful in analyzing and predicting Pin Pile performance. Data are provided from the full scale Test Pile Programs conducted at Mobile, AL and Port Vancouver, WA. Given that Pin Piles are usually installed in areas of low headroom or restricted access, and through difficult, occasionally contaminated soils, the paper also describes key aspects of construction.

Jan 1, 1993

By Douglas Brittsan

This paper presents pile tension and compression load test results for the Southern Freeway Viaduct (North) pile load test site. The testing program represents a collaboration between California Department of Transportation (Caltrans), Federal Highways Administration (FHWA), and a group of pile manufacturers and construction firms. The participating manufacturers included Fundex, Halliburton, Monotube, and Nicholson, with each firm supplying proprietary pile systems. The field test program measured and will allow the direct comparison of the tensile and compressive capacity of nine common and proprietary pile systems installed in nearly identical soil conditions. Data reported here-in details pile compression and tensile load-deformation measured at the pile head. Cursory data regarding pile installation details are included to aid in data interpretation.

Jan 1, 1993

By Samuel J. Kosa

The Monotube is a uniformly tapered high-strength steel shell pile manufactured for friction pile applications. The Monotube pile was developed in the early 1920's in Canton, Ohio. Its first commercial installation was an Ohio railroad trestle in 1926. The Monotube has been manufactured in the same Canton plant since its inception. The Monotube is produced in four diameters, 12, 14, 16 and 18 inches, with U. S. Standard Gage wall thicknesses of 9, 7, 5 and 3. The uniformly tapered Monotube section can be manufactured in one of three rates of taper.

Jan 1, 1993

By Jon E. Bischoff

Construction of a secondary clarifier on the banks of Rainy River, Northern Minnesota, required the driving of H-piles 14HP102 to a sloping, very strong bedrock through thick deposits of soft and medium stiff soils. Pile toe protection, APF Hardbite HP 77750, was specified to prevent damage to the pile toe and to enable the pile toe to bite into the bedrock surface. The toe protection worked well for bedrock sloping less than 2H:1V. However, where the bedrock was steeper, the piles experienced damage and failed to reach bearing. In most cases, the also the replacement pile failed. Pile Driving Analyzer measurements showed that on encountering the bedrock, the pile toe reflection, which at first was sound, deteriorated indicating pile toe damage. Extraction for visual inspection showed that the failed piles were bent and had deformed pile shoes. In areas of steeply sloping bedrock and for replacement piles, an alternative shoe, the Scanpile Herkules rock shoe, was employed. This pile shoe proved to be able to secure the pile toe into the rock and to eliminate the problem. The costs of the Herkules rock shoe considering price, shipping, and attaching, were about equal with the Hardbite shoe.

Jan 1, 1993

By Brian Maroney

In this paper an overview of the California Department of Transportation's (CALTRANS) bridge design criteria is presented. Special emphasis is focused upon seismic design and retrofit criteria. Topics include earthquake load definitions, foundation and structure type selection, structural earthquake analysis, and structure behavioral requirements.

Jan 1, 1993

By F. M. Abdrabbo

Flight auger bored piles are formed by screwing a continuous flight auger into the ground, and pumping cement/sand grout or concrete down the hollow stem of the auger as its withdrawn. The auger is driven at the top by hydraulic or electrical motor and is guided by a vertical crane leader. Loading tests on concrete piles are described. The stability plot method is used to drive the shaft friction and the end bearing load components of the pile capacity. This paper outlines features of crucial construction factors that affect the geotechnical capacity of this type of piles. These factors include, vertical speed of auger during boring, grout factor, grout pressure, number of reborings, type of material, and slump of concrete used to form the piles. Two of these factors are highlighted in this paper. It was found that, shaft resistance is independent of grout factor, whilst point resistance increases as grout factor increases. Nevertheless the engineer should decide the safe pile load associated with the most economical grout factor. High vertical speed of auger during boring of piles may cause disaster for the adjacent buildings, due to soil decompression.

Jan 1, 1993

By Lawrence P. Goldfarb

This paper presents the results of the geotechnical investigation for the repair of the Fashion Island Boulevard Bridge, Bridge No. 350160, in San Mateo, California. The concrete, precast girder bridge suffered considerable damage during the Loma Prieta earthquake. The existing 36-inch, precast, prestressed concrete piles cracked and spalled at their tops. Based on analyses performed by Biggs Cardosa Associates, structural engineers, the piles did not have sufficient strength and ductility to resist the dead plus seismic loads specified in the Caltrans "Bridge Design Specifications". Additional support for the bridge was needed and the repair strategy consisted of installing large diameter pipe piles at the existing bent and abutment locations. This paper describes the geotechnical engineering analysis and design decisions for the large diameter pile design.

Jan 1, 1993

By R. G. Horvath

The Statnamic loading test is a new and innovative method for testing deep foundations. The test is relatively inexpensive, quick, easily mobilized, provides for direct measurement of applied load and corresponding displacement, and is capable of very high loading capacities. The long duration of the applied loading, as compared to a dynamic loading test, allows for a straightforward determination of the static behaviour of the foundation tested. A new method of analysis of the Statnamic loading test, the Equilibrium Point Method, is presented. A description is given of the pile-soil model and a demonstration of how the static load-displacement behaviour of deep foundations may be predicted from the Statnamic loading test data. The Equilibrium Point Method of analysis is applied to three types of deep foundations in soils which respond differently to fast loading rates. These case histories, from Canada and the United States, include data from static loading tests for direct comparison, and demonstrate the ability of the Equilibrium Point Method to predict static behaviour of the deep foundations.

Jan 1, 1993

By Peter Florian

At 5:50 am on October 1, 1992, the new $800 million Pittsburgh International Airport Midfield Terminal opened its gates to the world after five years of construction and more than 24 years of planning. Despite numerous design changes, this massive project was completed on time and substantially within budget. The importance of this airport to Allegheny County and the Pittsburgh region was recognized 24 years earlier by Allegheny County Commissioners Tom Foerster and the late Leonard Staisey. Staisey and Foerster established a program to acquire land for the "Airport of the Future".

Jan 1, 1993

By William M. Camp

An extensive design phase testing program in which 10 piles and 2 drilled shafts were instrumented and statically load tested to failure, was undertaken to establish relevant foundation design parameters for two bridges in Charleston, South Carolina, USA. The bearing strata at both test sites was a calcareous, overconsolidated, firm to very stiff, slightly sandy, clayey silt (locally known as Cooper Marl). Confirmation dynamic and static loading tests on production piles indicated only 50 to 60% of anticipated pile capacities; including consideration of time effects. Supplemental subsurface explorations did not reveal any significant variations in marl properties. Ultimately, 22 static and 75 dynamic tests were performed on production piles for a 2 mile section of the project. Pore water pressures in the marl were also monitored during and after pile driving. A study of unit skin friction in the marl as a function of time revealed two distinct trends: piles driven in areas with a sand overlaying the marl gained more capacity significantly faster than those driven through a clay or silt. Although the insitu marl properties are apparently similar across the site, the material immediately above the marl evidently has a large effect on pile capacity. This effect of overburden on pile capacity was verified by testing piles over a period of two years.

Jan 1, 1993

By Roy M. Schnabel

The Fashion Island Boulevard Bridge over the Marina Lagoon in San Mateo, California is an eight span precast, prestressed concrete girder bridge. It is approximately 495 feet in length and 61 feet in width. It is supported on 36" diameter octagonal, hollow precast-prestressed concrete pile columns. The bridge was constructed in 1968 and suffered considerable damage during the Loma Prieta Earthquake in 1989. A damage survey report prepared by the State's Office of Emergency Services (OES) recorded that sixteen of the twenty-one pile-columns sustained heavy to moderate damage from the Loma Prieta Earthquake. The damage consisted of cracking and spalling at the tops of the pile-columns. Spalls at the most heavily damaged columns exposed the prestressing strands and confinement reinforcing which also showed signs of corrosion.

Jan 1, 1993

By Mohamad H. Hussein

A minipile system was employed in underpinning a historical structure in Florida. The existing structure is founded on shallow foundations. Subsurface conditions at the project site consist of deep organic deposits interbedded with loose sand and silty sand. A minipile foundation system was deemed the most appropriate underpinning corrective measure for the already badly cracked structure. A total of 68 minipiles, 3.5 inch OD and 0.25 inch wall thickness closed-ended concrete-filled steel pipes, were installed to depths varying from 55 to 175 feet. Installation was accomplished with a pile driving hammer having a rated energy of 1 kip-ft. Highest required pile design load was 15 kips. Conventional static and wave equation analyses were performed to establish preliminary pile lengths, to assess pile drivability and establish driving resistance criteria. Dynamic pile testing using the Pile Driving Analyzer was conducted on six of the production piles. This paper describes geotechnical design considerations, installation procedures, and dynamic field monitoring. This case represents unique applications of pile dynamic testing and such slender, very long minipiles in compressible soils.

Jan 1, 1993

By Patrick Bermingham

This report presents the results of six STATNAMIC loading tests that were carried out on four different pile types at the CALTRANS 280 Test Site (Bridge No. 34-46) in conjunction with the Tension Pile Test Program. The STATNAMIC testing was performed by Berminghammer Corporation at the request of the California Department of Transportation, Office of Geotechnical Engineering. Others performed the static tension (uplift) and compression loading tests which werecarried out on the piles tested using the STATNAMIC method. A summary of the STATNAMIC test results is presented and discussed, and the appropriate results are compared with the static test results

Jan 1, 1993

By G. G. Goble

Dynamic pile testing is now over 20 years old as a routinely applied tool for evaluating driven pile installation. The first test on a cast-in-place pile was performed more that 15 years ago. The research that produced the method began almost 30 years ago. But, questions still arise regarding the appropriate use of this technique so some review is useful. Today a number of methods including dynamic testing all depending in some way on the application of dynamics are in routine use. First, Wave Equation analysis can be used to predict pile driveability before going to the field. The same approach can be used during driving to estimate the bearing capacity based on the blow count observed in the field. Dynamic measurements, on the other hand, can only be used after pile driving has begun. They offer predictions of pile capacity as well as measurements of hammer, driving system, and pile driving performance characteristics. The first part of this paper will be devoted to discussing how the foundation engineer can use these tools. First, a brief review of what dynamic methods actually do. In Wave Equation analysis a numerical model of the hammer, driving system, pile, and the soil is created by the engineer. The hammer is dropped on the pile and using a discrete, dynamic analysis the motion of the individual pile elements is calculated as a function of time. Of course, input information must be supplied by the program user to describe the hammer, driving system, pile, and soil. In the current state of development, the primary problem in input data is with the hammer performance (efficiency) and the soil description. Research may be able to do a better job with the soil data, but hammer performance will always vary from hammer to hammer and is dependent on the affectiveness of the inspection process. Prior to beginning pile driving the Wave Equation analysis supplies the best available estimate of what will happen when driving begins. It gives an estimate of blow count during driving, driving stresses, both tension and compression in the pile, and for diesel hammers, stroke. The selection of the driving system can be checked with the results of Wave Equation analysis and modifications can be made if required. For example, if the blow count at the required capacity was deemed excessive by the contractor a larger hammer could be tried or if driving stresses were too high changes could be made in the cushion or the hammer selection could be modified. All of these modifications are possible with only the cost of a computer run. The primary questions regarding the accuracy and reliability of Wave Equation analysis at this time is with regard to the assumptions made to represent the soil characteristics and the difficulty in predicting hammer performance.

Jan 1, 1993

By Mark DeSalvatore

Currently, at Caltrans, the Office of Structure Design is carrying out an extensive seismic retrofit program involving transportation structures throughout California. The goal of the retrofit program has been to upgrade existing transportation structures to meet the present seismic codes and anticipated loads that are generated during a seismic event Part of the retrofit program involves retrofitting existing structure foundations when required. To determine if the foundations of a specific structure need to be retrofitted, an engineering analysis of the existing foundations has to be done. If the engineering analysis of the structure foundations determines that the foundations will not meet the load carrying demands required by the structural engineer, the existing foundations are then retrofitted. The retrofit projects that require foundation modifications can be separated into two general cases. The first case comprises structures where the original designs will not meet the demands of the present seismic design code. In this case, the existing foundations are not capable of providing the load capacities the current seismic code requires. The second case consists of structures where the retrofitting of the superstructure will increase the required load carrying capacity of the existing foundations during a seismic event In this case, the anticipated load demands on the existing foundations are greater than the foundations are capable of providing. For either of the cases listed above, the present strategy for increasing the capacity of the existing structure foundation consists of installing tiedown anchors or large capacity piles to provide the required resistance to seisraically induced loads.

Jan 1, 1993

By Arturo Ressi di Cervia

The utilization of diaphragm wall construction in Hong Kong began in 1974 with the construction of the New World Center, the first diaphragm wall job built in the British Colony. That landmark job of which I am presenting a few slides and a schematic description, embodied all of the difficulties and problems which are encountered in the difficult geology of Hong Kong. A small rocky island in the South China Sea, Hong Kong provides one of the finest natural harbors in the world. It is its splendid harbor, coupled with the enterprising attitude of the Hong Kong Chinese and the laissez-fair attitude of the British government which has resulted in the explosive growth of this speck of land soon to revert to the political control of mainland China.

Jan 1, 1993

By M. England

A method for the analysis and prediction of single pile displacement behaviour is described. It is the displacement in time, under constant load, based on the use of hyperbolic functions to characterise individual constituents of the displacement-time behaviour. Extensive use of this technique has confirmed its validity in a variety of soils and that consolidation and creep settlement appear to be indistinguishable. The algorithms employed are suitable to model the displacement behaviour from the onset of load to infinite time for all types of piles and surface foundations. Until the advent of computer controlled static load testing, analysis of the displacement-time characteristic during pile load tests has been hindered by the quality of the data recorded and inconsistency of loading. This has hitherto made the development of suitable behavioural models very difficult. Understanding the soil deformation within a proper time framework allows the subject of pile instrumentation and testing to be developed. The equipment required is basically a computer controlled loading and pile head displacement measuring system which allows accurate analysis of the settlement characteristic in almost every situation.

Jan 1, 1993